15, FAIRING/ EXHAUST SYSTEM
SERVICE INFORMATION 15-1 REAR FENDER 15-5
p SIDE COVER/SEAT 16-2 EXHAUST PIPE/MUFFLER 16-7
FAIRING 15-2
GENERAL
d SERVICE INFORMATION
4
Bo net service the exhaust system while tts hot.
p TORQUE VALUES
Exhaust pipe joint nut 22. Nem (2.2 kg-m, 16 ft-lb}
Muffler band bolt 20 Nem (2.0 kg-m, 14 fib}
Muffler bolt 25 Nem (2.5 kg-m, 18 fib)
Exhaust pipe heat protector bolt 10 Neen (7.0 kg-M, 7 ft-lb) Apply locking agent to the threads
oar carrier mounting batt (AFTER “&8) —35.Nem (3.8 kg-m, 25 ft-b)FAIRING/EXHAUST SYSTEM
SIDE COVER/SEAT
REMOVAL/INSTALLATION
Remove the side cover bolts, and remove the sida cavers by
pulling the eavar etude out of the gramets.
Remove the sear bolts and remove the seat, sliding it back. (1) seAT
Install the seat end side covers in the reverse order of the re-
movel
FAIRING
REMOVAL/INSTALLATION
Remove the two scraws and right and left felting cover,
Remove the two screws and inner cover,
Femove the center ‘airing and windshield by removing four (1) SCREW. en bai (2| CENTERS
screws. FAIRING
Femeve the front grils by removing the four serews,
(4) FRONT
GRILLE
15-2FAIRING/EXHAUST SYSTEM
Remove the screws and right and lett alr guides.
remove the two serows and heat laze
Remove the ght and left faiings by removing the screws and
(ysTuD FAIRING
pulling the etud out of the fuel tenk gromot. \ ag
15-3FAIRING/EXHAUST SYSTEM
Install the removed parts In the reverse order of the wemoval
“| AFTER 88
(9) INNER COVER.
16) LEFT FAIRING
COVER,
AFTER ‘88
17) LEFT FAIRING
(3) CENTER,
FAIRING
(2) RIGHT FAIRING
COVER
(1) RIGHT FAIRING
(7) LEFT FAIRING
(10) HEADLIGHT
PLATE,
(11) RIGHT AR,
GUIDE (9) FRONT GRILLE (s) Leet ain GUIDE
15-4FAIRING/EXHAUST SYSTEM
REAR FENDER (1) FENDER MOUNTING 2) TURN SIGNAL
BOLIS, LIGHT BOLT
) REMOVAL/INSTALLATION
Inctall the rear fonder escombly in the reverse order of the ro-
moval.
(1) RIGHT TURN SIGNAL |3| REAR FENDER E
LsHT
12] REAR FENDER A
(4) LEFT TURN SIGNAL,
> LisHT
15-5FAIRING/EXHAUST SYSTEM
AFTER 86:
Remove the seat (page 18-2).
Disconnect the rear turn signal and tallibrakelight connectors.
Remove the four rear carrier mounting bole, rear carrier and
rear turn signels.
Famove the fear ‘ender A, rear fender 8, and rear fender
mount by remioving the two bolts.
Install the removed parts in tho revere order of the removal
(3) REAR CARRIER 36 Nem (3.5 kgm, 26 fib)
(4) REAR FENDER B
(5) REAR FENDER,
MOUNT
15-6FAIRING/EXHAUST SYSTEM
EXHAUST PIPE/MUFFLER [Fv SiOre ei Sano RSS a Son ar
5
EXHAUST PIPE REMOVAL f :
Remove the right side cover (page 15-21.
Loosen the muffler band bolts, and remove the exhaust pipe
int nuts, exhaust pipes joint collars and exhaust pipe aas-
ket
Nore
+ Whenever the exhaust pipe geskets are removed, replace 3 13) EXHAUST
with new ones. : PIPES
Remove the exhaust pipe heat protector, if necessary.
(2) MUFFLER BAND
EXHAUST MUFFLER REMOVAL
Remove the side covers Ipage 15-2)
Loosen the muffler band bolts, and remove the muffler bolts
‘ond mufflers.
Install the removed parts in-the reverse order of the removal,
‘and tighten the bolts and nuts to the specified teraue.
‘TORQUE:
Exhaust pipe joint nut: 22 Nim (2.2 kgm, 16 ft-b)
Muffler band bolt: 20 Nem (2.0 kg-m, 14 feb)
Mutfiar bo! 25Nom(2.5 ka-m, 18 ft-lb}
Exhaust pipe heat protector bot
10 Nem (1.0 kg-m, 7 fbi Apply a locking agent to the
threads.
(4) MUFFLERS
(2) EXHAUST PIPES
(1) EXHAUST PPE
HEAT PROTECTOR (3) MUFELER
SANDS
(4) EXHAUST PPE
casket
5) EXHAUST PIPE
YOINT COLLARS
15-7