Professional Documents
Culture Documents
Dasmesh Parivar International School: Project Report
Dasmesh Parivar International School: Project Report
INTERNATIONAL
SCHOOL
PROJECT REPORT
ON
TRANSFORMERS
Submitted By:
TANUJ GUPTA
CLASS: XII
ROLL NO:
________________
Certificate
This is to certify that Tanuj Gupta, student of Class XII, Dasmesh Parivar
International School, has completed the project titled Transformers during
the academic year 2012-2013 towards partial fulfillment of credit for the
Physics practical evaluation of CBSE 2013, and submitted satisfactory report,
as compiled in the following pages, under my supervision.
_________________
Department of Physics
Dasmesh Parivar International School
Acknowledgement
s
"There are times when silence speaks so much more loudly than
words of praise to only as good as belittle a person, whose words
do not express, but only put a veneer over true feelings, which
are of gratitude at this point of time."
I would like to express my sincere gratitude to my physics mentor for his vital
support, guidance and encouragement, without which this project would not
have come forth. I would also like to express my gratitude to the staff of the
Department of Physics at Dasmesh Parivar International School for their
support during the making of this project.
TANUJ
GUPTA
INTRODUCTION
The transformer is a device used for converting a
low alternating voltage to a high alternating
voltage or a high alternating voltage into a low
alternating voltage. It is a static electrical device
that transfers energy by inductive coupling
between its winding circuits. Transformers range in
size from a thumbnail-sized coupling transformer
hidden inside a stage microphone to huge units
weighing hundreds of tons used in power plant
substations or to interconnect portions of the
power grid. All operate on the same basic
principles, although the range of designs is wide.
While new technologies have eliminated the need
for transformers in some electronic circuits,
transformers are still found in many electronic
devices. Transformers are essential for highvoltage electric power transmission, which makes
long-distance transmission economically practical.
A transformer is most widely used device in both
Clo
se-up of single-phase pole mount transformer.
PRINCIPLE
It is based on the principle of mutual induction that
is if a varying current is set-up in a circuit then
CONSTRUCTION
A transformer consists of a rectangular shaft iron
core made of laminated sheets, well insulated from
one another. Two coils p1 & p2 and s1 & s2 are
as
the
switch
is
open.
For
an
ideal
An ideal voltage step-down transformer. The secondary current arises from the
action of the secondary EMF on the (not shown) load impedance.
THEORY AND
WORKING
When an altering e.m.f. is supplied to the primary
coil p1p2, an alternating current starts falling in it.
The altering current in the primary produces a
changing magnetic flux, which induces altering
voltage in the primary as well as in the secondary.
In a good-transformer, whole of the magnetic flux
linked
with
primary
is
also
linked
with
the
(1)
Es = -Ns D/dt
(2)
(3)
E Ep
Ip Rp
= 0 or Ep = E
Es I s
Es Is
=
Ip / Is
Or
=
In a step up transformer
EFFICIENCY
Efficiency of a transformer is defined as the ratio of
output power to the input power i.e.
= output power / input power = Es Is / Ep Ip
Thus in an ideal transformer, where there is no
power losses, = 1. But in actual practice, there
are many power losses; therefore the efficiency of
transformer is less than one.
ENERGY LOSSES
In practice, the output energy of a transformer is
always less than the input energy, because energy
losses occur due to a number of reasons as
explained below.
1. Loss of Magnetic Flux: The coupling
between the coils is seldom perfect. So, whole of
the magnetic flux produced by the primary coil is
not linked up with the secondary coil.
2. Iron Loss: In actual iron cores in spite of
lamination,
Eddy currents are produced. The magnitude of
eddy current may, however be small. And a part of
energy is lost as the heat produced in the iron core.
3. Copper Loss: In practice, the coils of the
transformer possess resistance. So a part of the
energy is lost due to the heat produced in the
resistance of the coil.
4. Hysteresis Loss: The alternating current in
the coil tapes the iron core through complete cycle
of magnetization. So Energy is lost due to
hysteresis.
5. Magneto restriction: The alternating
current in the
Transformer may be set its parts in to vibrations
and sound may be produced. It is called humming.
USES OF
TRANSFORMER
A transformer is used in almost all a.c. operations
In
voltage
regulator
for
T.V.,
refrigerator,
is
used
for
the
A Big Transformer
Bibliography
The End