EBEB393 ~ Experiment |
Semester 2 2016/2017
COLLEGE OF ENGINEERING
PROGRAMME,
PUTRAJAYA CAMPUS
Bachelor of Electrical Power Engineering (Honours)
Bachelor of Electrical and Electronics Engineering
(Honours)
SUBJECT CODE EEEB393
SUBJECT Power Electronics
PRE-LAB 1 Diode Rectifiers
Instructor Name
Section 1A / 1B /1C / 2A / 2B 2C Group:
Date of Pre-lab report submission: 31% October 2016
GMD _ | Student ID
Student Name:
erect
Pre-Lab 1 Evaluation:
Simulation Model [10 marks]
Simulation Results [15 marks]
Condusion [05 marks]
Total [30 marks}
Page | of 10EBEB393 ~ Experiment | Semester 2 2016/2017
Student is required to submit @ short report which contains the following.
1, Simulation model [10 marks]
2, Simulation resuit with short discussion, [15 marks}
Input voltage(s) of the rectifier,
Input current(s) of the rectifier,
Diode(s) voltage, vas
Diode(s) current, 14,
Oviput current(s),
Ouiput valtage(s).
menses
3. Condlusion [5 marks]
Report Format: Maximum 6 pages (A4 size), minimum fort size is 10, Single line spacing,
dovble-pege printing
Page 3 of 10£393 — Experiment | Semester 2 2016/2017
@
nee
COLLEGE OF ENGINEERIN
PUTRAJAYA CAMPUS
PROGRAMME Bachelor of Electrical Power Engineering (Honours)
Bachelor of Electrical and Electronics Engineering
(Honours)
SUBJECT CODE EEEB393
SUBJECT Power Electronics
LABORATORY Experiment | Diode Rectifiers
TIME 3 hours
Instructor Name
Section: 1A / IB / 1C / 2A / 2B / 2C Group:
Date of Experiment
Lab Report Due Date: One week after the laboratory work is conducted.
Group Member
Student Dy
‘Student Name:
Experiment 1 Report Evaluation:
Ree Total marks score
Part! [10 marks}
Part? [10 marks}
Pat3 [10 marks}
Discussion [43 marks]
Total
[73 marks}
Page 5 of 10EBEB393 ~ Experiment |
Part 1: SINGLE-PHASE HALFWAVE RECTIFIER
Cireuit Diagram:
va fo
Ta AGT] FORT)
Stand Stand
Tasigterstmeeeov | [geting | Labret
Semester 2 2016/2017
Connect the circuit in Figure 1 for resistive load.
Set the supply voltage to 45V
Set the resistance value to S00.
Check the following setting/connection:
a Check each Isolation Amplifier setting,
The grounding between [soletion Amplifier and Oscilloscope
5. Ask the lab instructor to check your circuit connection,
6. Switch on the tepping transformer
7. Obtain end print the following waveforms using OSC:
Output voltege, V2, vs. Output current, J,
‘6. Output voltage, V5, vs Diode voltage, Vs
8. Measure end record the parameters in Table 2
Note: measured the Izy from the OSC
‘Table 2: Result for R-Load
[2 marks}
[2 marks}
RLoad 302
Vo
Vrms
Toa
Toons
ay
Iams
Page 7 of 10
16 marks}EBEB393 ~ Experiment | Semester 2 2016/2017
Part 3: THREE-PHASE FULLWAVE RECTIFIER
ke
id a
ols] ffoTsasin Ape
hare A hamele
tine setnc
t
Teppng artes t5/80V
$5) 45
i hk
|
|
Ss
AAS
Figure 3: Three-phase full-wave rectifier
1. Comnect the circuit in Figuee 3 for resistive load
2. Set the supply voltage to 45V for STAR connection.
Set the resistance value to 500.
4. Check the following setting/connection:
a Check each Isolation Amplifier setting,
The grounding between Isolation Amplifier and Oscilloscope
5. Ask the lab instrustar to check your circuit connection,
6. Switch on the tepping transformer
7. Obtain end print the following waveforms using OSC:
Output voltege, V2, vs. Output current, J, [2 marks]
b. Diode curent, Js vs. Output curest,/, [2 marks}
8. Messure end record the parameters in Table 4
Table 4: Result for R-Load
RLoad 500
Vos
[6 marks}
Page 9 of 10