SYLVANIAS
DH engrnig ita sri
CHARACTERISTICS
GENERAL DATA
Focusing Method... «= Electrostatic
Defiection Method 2 2 202 2 12 2. 1 2 2 Blectrostaic
Phosphor* PLP? P7 Pu
Fluorescence. . Green Green Blue-White Blue
Phosphorescence. "— Green Yellow —
Persistence. . Medium Long Long Shore
Faceplate Clear
“Ia addition, che SDEP—can be supplied with several
other screen phospors.
ELECTRICAL DATA
Heater Voltage 63 Volts
Heater Current 06 + 10% Ampere
Direct Incerelecirode Capacitances (Approx.)
Grid to All Other Electrodes 6.0 pn
Beoween Deilecting Plates 1-2 |. | 3.5 wae
Becween Deflecting Plates 3-4 50 maf
Defiecting Plate 1"to All
Other Electrodes . 100 maf
Deflecting Plate 24 ro All
‘Other Electzodes 65 wal
Deflecting Plate 31 to All
Other Electrodes 75 wal
Deficting Plate 4" to All
Other Electrodes . 5.0 put
MECHANICAL DATA
Minimum Useful Screen Diameter 4¥4 Inches
Bulb Jay
Base (Smal Sell Duoeaa 12-Pin) a Bi2-43
Basing :t : RE
Weight (Approx) 14 Pounds
MAXIMUM RATINGS (Absolute Maximum Values)
Anode No. 2 Voluge . . . . 2750 Vols de
‘Anode No. 1 Voltage . : 1100 Vols de
Grid Voltage
‘Negative Bias Value 20 Volts de
Positive Bias Value. | | OVolrs = de
Positive Peak Value 2 Volts
Peak Heater-Cathode Voltage
Heater Negative with Respect to Cathode . 140 Volts
Heater Positive with Respect to Cathode . 140 Volts
Peak Voltage Beoween Anode No.2 and
‘Any Deflection Place 550 Volts
TYPICAL OPERATING CONDITIONS
Anode No.2 Voltage 2. + 2000 Vols de
‘Anode No. I Voltage for Focus || ‘340 10640 Volts de
‘Maximum Grid Voltage Required for Cutoff? 90 Vols de
Deflection Factors,
Deflecting Plates 1-28, 48 t0 64 Volts de/Inch
Deflecting Places 3-47 27037 Volts de/Tach
Spot Position (Undeected)® - 10mm Max,
CIRCUIT VALUES
Grid Circuit Resistance... 2.
Deflection Circuit Resistance |
15 Megohms Max.
5.0 Megohms Max.
SYLVANIA
SDEPI
SDEP-"
QUICK REFERENCE DATA
Oscilloscope Tube
5” Direct Viewed
Round Glass Type
Electrostatic Deflection
Electrostatic Focus
High Deflection Sensitivity
SYLVANIA
ELECTRONIC TUBES
Splvania ee Prd a
PICTURE TUBE OPERATIONS
SENECA FALLS, NEW YORK
Prep end Reload By The
‘TeciiNicae PUBLICATIONS SBCTION
"EMPORIUM, PENNSYLVANIA
‘OcTOBER, 1961,
PAGE 1 OF 2
File Under
SPECIAL AND GENERAL PURPOSE.
‘CATHODE RAY TUBESSYLVANIA
SEPT
SEP."
PAGE 2
NOTES:
Positive voltage ow DI (Pin No. 10) will move spot approximately in direction of Pin No. 4.
Positive voltage on D3 (Pin No. 6) will move tpot approximately in direction of Pin No, 1
Brilliance and definition decrease with decreasing Anode No. 2 Voltages. In general, Anode No. ? Voltage should not
be ess than 1000 volts for the Type SDEPI and not lexs than 1500 sts for the Types SDEP2, SDEP?, and SDEPI!
Visual extinction of undeflected focused spot
Angle between trace produced by Plates D1-D2 and the plane through the tube axis and Pin No. 4 does not exceed 10
Angie between DI-D2 trate and D3-D4 trace is 90° * 1",
Deflecting Plates 1-2 are nearer the screen.
Deflecting Plates 3-4 are nearer the base.
With she tube shielded and with all deflection plates connected to A2, he spot shall fall within a square, 10mm on a ide,
centered with respect to the face and with the sides parallel to the deflection axes
OUTLINE
vserur screen 1m,
DIAGRAM NOTE:
1. Dimensions are in inches.