Professional Documents
Culture Documents
Product Name
GSM BSS
Product Version
INTERNAL
Confidentiality Level
INTERNAL
Total 34 pages
Prepared by
GSM&UMTS
Network
Performance
Research Department
Wang Fei
Reviewed by
Reviewed by
Granted by
Date
2008-06-18
Date
Date
Date
2008-10-25
Page 1 of 34
GSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
Revision Record
Date
2008-06-18
Revision
Version
0.8
2008-07-18
1.0
2008-10-25
Change Description
Draft completed.
The document is modified according to
review comments.
Author
Wang Fei
Wang Fei
Page 2 of 34
GSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
References
Number
1
2008-10-25
References
GSM BSS Network KPI (Immediate
Assignment Success Rate) Baseline
Author
Liu Xiuyu
Date
2007-03-10
Page 3 of 34
GSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
Content
1 Overview of the Immediate Assignment Success Rate..............................................................7
1.1 Definition.................................................................................................................................7
1.2 Signaling Procedure and Measurement Points......................................................................8
1.3 Symptom Description .............................................................................................................8
2 Factors Concerning Immediate Assignment Success Rate........................................................9
2.1 Signaling Factors....................................................................................................................9
2.2 Factor Analyzing According to the Definition of the KPI.........................................................9
2.3 Factors Analysis....................................................................................................................11
2.3.1 Equipment Faults............................................................................................................11
2.3.2 Um Interface Problems...................................................................................................11
2.3.3 SDCCH Congestion........................................................................................................11
2.3.4 MS Problems..................................................................................................................12
3 Method of Analyzing the Problem of Low Immediate Assignment Success Rate.....................12
3.1 Process of Analyzing the Problem of Low Immediate Assignment Success Rate...............12
3.2 Method of Solving the Problem of Low Immediate Assignment Success Rate....................14
3.2.1 Equipment Faults............................................................................................................14
3.2.2 Um Interface Problem.....................................................................................................14
3.2.3 System Capacity (Congestion) Analysis ........................................................................19
3.2.4 MS Problem Analysis......................................................................................................24
4 Test Method...............................................................................................................................26
5 Cases of Immediate Assignment Success Rate Optimization..................................................27
5.1 Case 1: Decrease in Immediate Assignment Success Rate Because of SDCCH Congestion
Caused by Incorrect LAC Setting...........................................................................................27
5.2 Case 2: SDCCH Congestion Caused by a Burst of Location Updates................................28
5.3 Case 3: Low Assignment Success Rate Because the RACH Minimum Access Level Is Set
to 0.........................................................................................................................................28
5.4 Case 4: Low Immediate Assignment Success Rate in Some Cells Because of MS Error...30
6 Onsite Information that Needs to Be Obtained.........................................................................33
2008-10-25
Page 4 of 34
GSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
Tables
Table 1 Mapping between formulae and factors..........................................................................10
2008-10-25
Page 5 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
2013-7-18
Full Spelling
BSC
BTS
SDCCH
Page 6 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
1 Overview
of
the
Immediate
INTERNAL
Assignment
Success Rate
Immediate assignment success rate indicates the success rate of the MS accessing
the signaling channel. It concerns the procedure from the MS sending a channel required
message to the BTS to the MS sending an establish indication message to the network.
Immediate assignment success rate is a key access counter. It directly reflects the
success rate of the MS accessing the signaling channel and affects the user experience.
The BSC versions concerned in this document are as follows:
BSC32G3BSC32V300R007C01B015
BSC6000BSC6000V900R001
1.1
Definition
The immediate assignment success rate is calculated from traffic statistics. The
Assignment
Success
Rate
(Successful
Immediate
2013-7-18
Page 7 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
1.2
INTERNAL
MSC
BSC
Channel REQ
Channl RQD
A1
Channel ACT
Channel ACT ACK
I MM ASS CMD
B1
f i rst SABM
UA
EST I ND( CM Servi ce REQ)
C1
Note:
A1: Immediate Assignment Requests (Channel Requests (Circuit Service))
B1: Immediate Assignment Commands
C1: Successful Immediate Assignments (Call Setup Indications (Circuit Service))
1.3
Symptom Description
If the immediate assignment success rate decreases, the following symptoms may
occur:
2013-7-18
Page 8 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
Success Rate
2.1
Signaling Factors
According to the signaling flow, the factors concerning the immediate assignment
2.2
Page 9 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
Formula
Affecting Factor
Um
interface
problems
Reception
of CHAN
ACTIV
NACK
because
of
equipment
faults
during
SDCCH
activation
2013-7-18
SDCCH
congestion
MS
problems
Page 10 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
2.3
INTERNAL
Factors Analysis
Generally, reception of CHAN ACTIV NACK during the SDCCH activation is caused
by equipment faults. If one TRX fails in the cell configured with multiple TRXs, the
immediate assignment may fail or the SDCCH may be congested. If you are sure that the
fault lies in a TRX, replace the faulty TRX. Otherwise, check the cables in the antenna
system and the VSWR. If the cables are properly connected and the VSWR is normal,
you need to replace the TRX, and then check whether services are normal again.
The BTS may mistakenly regard the interference on the Um interface as the random
access signal. This may lead to immediate assignment failure or SDCCH congestion. In
this situation, the interference problem should be solved.
2.3.2.2
In a cell configured with six or more than six TRXs, the combination losses of the
BCCH TRX and non-BCCH TRXs are different, leading to coverage difference. If the
SDCCH is configured on the non-BCCH TRX, a call that is far away from the serving cell
may fail to access the SDCCH when it is assigned to the non-BCCH TRX. Thus, the call
drop may occur.
Page 11 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
configuration. For SDCCH congestion caused by traffic burst, such as group sending of
short messages and location update at the portal of a tunnel, the problem cannot be
completely solved. You can, however, alleviate the congestion by enabling the functions
such as SDCCH dynamic adjustment.
2.3.3.2
Location area planning: a reasonable location area plan can help alleviate the
SDCCH congestion.
Dynamic SDCCH assignment: the dynamic SDCCH assignment can help alleviate
SDCCH congestion.
Dual-band network: a reasonable setting of dual-band network parameters (for
example, CRO, CBA, CBQ, and Cell Reselection Hysteresis) can help alleviate SDCCH
congestion.
Check whether the settings of related timers (such as T3101, T3122, T3212, and
T3111) are reasonable.
2.3.4 MS Problems
In some cases, the location updates performed by the MS are abnormal, leading to a
low immediate assignment success rate. These MSs fail to establish a link on the
SDCCH after sending the channel request, causing a low immediate assignment success
rate. For the detailed analyzing method and case study, see case 4 in section 3.
2013-7-18
Page 12 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
the range in which the problem exists, and then find out the factors related to the problem
according to KPI statistical formulae. For details, see section 2.2 "Factor Analyzing
According to the Definition of the KPI". In the case of recommended formula, the general
process of analyzing the problem is as follows:
Start
Analysis of low
immediate assignment
success rate
Equipmen
t fault?
Um interface
fault?
Yes
Ye
s
Check TRX
availability and
TRX alarm
Check
SDCCH
availablity
Idle interference
band/signaling
analysis
TRX receive
level and quality
analysis
Check number of
SDCCH activation
failures/timeout
TRX fault or
transmission
failure
Solve
Interferenc
e problem
RACH
overload
times
No
Ye
Insufficient system s
capacity?
No
Abnorma
l
Traffic volume
per SDCCH
exceeds paln
MS fault?
SDCCH and
TCH traffic
volume
analysis
Incoming and
outgoing
handovers of
the cell
Check timers
related to
location
update
Check SDCCH
dynamic
configuration
Enable CBA
of the cell
Replan the
location
areas
Hardware
expansion
Locate
problem
and submit
report
No
Problem
solved?
Yes
End
2013-7-18
Page 13 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
Figure 1 Process of analyzing the problem of low immediate assignment success rate
3.2
find out the difference between the actual immediate assignment success rate and the
expected value. You should also find out the influence of the problem and the definition of
the specific immediate assignment success rate KPI.
BSC Level
Cell Level
Page 14 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
success rate. Especially in the areas with a small space between BTSs and dense BCCH
frequency planning, the system allocates SDCCH for each signal if a large number of
interference signals are received. Thus, the congestion may occur. In this situation, the
immediate assignment success rate and paging success rate decrease, and the RACH
may be overloaded. You can locate the problems by analyzing the idle interference bands
and the TRX receive quality during the call.
If the system mistakenly regards the interference as a random access signal and
sends an assignment command, the immediate assignment will fail. You can locate the
problem by analyzing the Chan Req message.
For the SDCCH congestion caused by interference, you can check the following
traffic statistics for reference:
Cause
SDCCH
congestion
caused by
interference
BSC Level
Cell Level
TRX Level
Call Measurement
-> Flow Control
Measurement per
Cell -> MSG CCCH
LOAD IND (RACH)
Messages Sent on
Abis Interface
MR Measurement ->
Analyzed Measurement
of Interference Band per
TRX
Receive
Quality
Measurement per TRX
BSC Level
Cell Level
Page 15 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
SDCCH
per BSC
INTERNAL
Page 16 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
MS codes
bits
8 .... 1
101xxxxx
Emergency call
110xxxxx
Call re-establishment; TCH/F was in use, or
TCH/H was in use but the network does not
set NECI bit to 1
011010xx
Call re-establishment; TCH/H was in use and the
network sets NECI bit to 1
011011xx
Call re-establishment; TCH/H + TCH/H was in use
and the network sets NECI bit to 1
100xxxxx
0010xxxx
0011xxxx
0001xxxx
Answer to paging
See table 9.9a/3GPP TS 04.08
111xxxxx
Originating call and TCH/F is needed, or originating call
and the network does not set NECI bit to 1, or
procedures that can be completed with a SDCCH and the
network does not set NECI bit to 1.
note 1
0100xxxx
Originating speech call from dual-rate mobile station when
TCH/H
is sufficient and supported by the MS for speech calls and the network
sets NECI bit to 1
note 5
0101xxxx
Originating data call from dual-rate mobile station when TCH/H
is sufficient and supported by the MS for data calls and the network sets
NECI bit to 1
note 5
000xxxxx
Location updating and the network does not set NECI bit to 1
0000xxxx
0001xxxx
Other procedures which can be completed with note 1
an SDCCH and the network sets NECI bit to 1
011110xx
01111x0x
01111xx0
One phase packet access with request for single timeslot uplink
transmission; one PDCH is needed.
01110xxx
Single block packet access; one block period on a PDCH is
needed for
two phase packet access or other RR signalling purpose.
2013-7-18
Page 17 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
01100111
LMU establishment
01100xx0
01100x01
01100011
01111111
INTERNAL
note 2
note 2a
note 2b
NOTE 1: Examples of these procedures are: IMSI detach, Short Message Service (SMS),
Supplementary Service management, Location Services.
NOTE 2: If such messages are received by a network, an SDCCH shall be allocated.
NOTE 2a: If such messages are received by a network, an SDCCH may be allocated.
NOTE 2b: This value shall not be used by the mobile station on RACH. If such message is
received by the network, it may be ignored.
3.2.2.2
Coverage Difference
If the combination mode of the BCCH TRX and the non-BCCH TRX is different, or
the losses are inconsistent because of different transmit power or other problems, the
assignment on the non-BCCH TRX may fail.
The causes can be classified into three types:
The transmit power of TRXs in the same cell is different.
If concentric cell technology is not applied, the power of different TRXs on the
antenna input port is different because of different uplink losses. This causes inter-TRX
coverage difference. Thus, assignment failure may occur. To solve this problem, check
whether the combiner, divider, CDU, or SCU is properly connected.
Multiple antennae are installed in a cell.
When multiple antennae are installed in a cell, the coverage differences of the
2013-7-18
Page 18 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
antennae may cause assignment failure. You can solve this problem through engineering
adjustment.
The transmit and receive antennae are not on the same horizontal plane or their
tilts are not the same. You can solve this problem by adjusting the antennae.
Generally, heavy traffic on the SDCCH is caused by frequent location updates. You
can check the rate of the SDCCH being occupied by querying the counter Channel
Requests (Location Updating) and the total number of channel requests. Figure 3
shows the ratios of different kinds of SDCCH requests to the total number of SDCCH
requests on Shanghai Unicom when the traffic is heavy. If the ratios are high, check the
location area planning and the drive test result. If the edges of location areas are
configured in the area with heavy traffic, reconfigure the location areas. In addition, you
can adjust the CHR parameters to reduce location updates. For details, see Case 1.
If the SDCCH congestion rate is high (greater than 5%), the traffic volume on each
SDCCH may have exceeded the limit as planned. You should check the configuration of
the location update and SDCCH dynamic configuration parameters. If the settings of
parameters are reasonable, a hardware capacity expansion is required.
If the congestion rate and traffic volume of the SDCCH are high, but the traffic
volume of the TCH is normal, the SDCCH congestion may be caused by burst traffic. For
the sites along the railway, especially for these near the tunnel portal, the capacity
configured is generally small. When a train passes through or stops, a large number of
location updates occur, which finally lead to SDCCH congestion. In addition, during the
period when the volume of short messages is large, SDCCH congestion may occur. This
problem cannot be completely solved, but you can take some measures to alleviate the
congestion. For example, configure more SDCCHs, or enable the dynamic conversion
between the SDCCH and TCH. For details, see Case 2.
2013-7-18
Page 19 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
For the configuration of related parameters, see section 3.2.3.2 "Congestion Caused
by Inappropriate Parameter Configuration".
You can check the following traffic statistics for reference:
Cause
BSC Level
Cell Level
Congestion
caused by
heavy traffic
on
the
SDCCH
Call
Measurement
->
Immediate
Assignment
Measurement per Cell -> Channel Requests per Cell ->
Channel Requests (MOC), Channel Requests (MTC),
Channel Requests (Emergency Call), Channel Requests
(Call Re-establishment), Channel Requests (Location
Updating), Channel Requests (Packet Call), Channel
Requests
(LMU+Reserved),
Channel
Requests
(Protocol Incompatible)
KPI Measurement per Cell -> SDCCH Traffic Volume,
SDCCH Seizure Requests, Failed SDCCH Seizures due
to Busy SDCCH
Figure 3 shows the ratios of different kinds of SDCCH requests to the total number
of SDCCH requests on Shanghai Unicom when the traffic is heavy:
Rat i os of Di f f erent Ki nds of SDCCH Request s to t he Total Number of SDCCH Requests on
Shanghai Uni comwhen t he Traf f i c i s Heavy
Rati os of di f f erent ki nds of SDCCH request s
50. 000%
47. 003%
45. 000%
40. 000%
35. 000%
31. 059%
30. 000%
25. 000%
20. 000%
9. 309%
Figure 3 Ratios of different kinds of SDCCH requests to the total number of SDCCH
requests on Shanghai Unicom when the traffic is heavy
Page 20 of 34
0. 006%
A300KNumber
of SDCCH
r equest s
( pr ot ocol
i ncompat i bl e)
0. 001%
A300I Number
of SDCCH
r equest s ( LMU +
Reser ved)
A300CNumber
of SDCCH
r equest s
( mobi l e
t er mi nat ed
cal l )
A300ANumber
of SDCCH
r equest s
( mobi l e
or i gi nat ed
cal l )
0. 030%
A300HNumber
of SDCCH
r equest s
( packet cal l )
0. 055%
0. 000%
A300F Number
of SDCCH
r equest s
( l ocat i on
updat i ng)
5. 000%
A300ENumber
of SDCCH
r equest s ( cal l
r eest abl i shment )
12. 538%
10. 000%
A300DNumber
of SDCCH
r equest s
( emer gency
cal l )
15. 000%
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
follows:
1. CRO: Generally, it is recommended that an MS should not camp on a cell with
high traffic volume or low QoS. The parameters of such cells should be set as follows:
firstly, set PT to 31, so that TO becomes invalid. Secondly, set C2 to the same value as
CRO subtracted from C1 so tha t the value of C2 is reduced and thus the possibility of
reselecting this cell is reduced. In addition, network operators can set the CRO according to
the actual conditions. The greater the CRO is, the more difficult it is for an MS to access
the cell.
2. Cell Reselection Hysteresis (CRH): This parameter is used to determine
whether cell reselection is performed between different location areas. This parameter
can prevent frequent location update, thus minimize the possibility of losing paging
messages. Generally, this parameter is set to 6 dB. For dual-band networks in urban
areas not sharing the location areas, this parameter is set to 810 dB.
If the traffic volume in an area is high, and signaling overload occurs frequently,
it is recommend that you set the CRH of the neighboring cells belong to different
LACs under this area to a larger value.
If the overlapping area of the neighbor cells under different location areas is
large, it is recommended that you set the CRH of the cells to a larger value.
If some areas between two neighbor cells under different location areas have
poor coverage, or if most of the MSs in the area (such as highways) move at a
high speed, it is recommended that you set the CRH of the cells to 26 dB.
Description
SDCCH
Dynamic
Allocation
Allowed
Idle SDCCH
Threshold
N1
2013-7-18
Page 21 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
TCH
Minimum
Recovery
Time(s)
T3122: This timer is started by the MS when the MS receives the IMMEDIATE
ASSIGN REJECT message. The MS can send a new channel request message
only after T3122 expires. If the length of T3122 is too short, the MS may send
the channel request message frequently when no system resources are
available. This increases the load on the RACH and CCCH.
T3212: This timer is used for the periodic location update. Increase the length of
this timer properly to reduce the load on the SDCCH brought by periodic
location update.
T3111: This timer delays the deactivation of channels after main signaling links
are disconnected to reserve time for repeated link disconnection. T3111 is
started during the disconnection of both TCH and SDCCH. The value of T3111
must be the same as the value of T3110 at the MS side. Generally, they are set
2013-7-18
Page 22 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
to 2 seconds. If the length of T3111 is too long, the SDCCH congestion rate is
increased.
5. RACH Min Access Level: If the value of this parameter is too small, much
interference may access the network, thus leading to SDCCH congestion. If the value of
this parameter is too large, it is probable that MSs cannot make the call even though the
signal level is high. This parameter should be set on the basis of the actual receiver
sensitivity of the BTS, the minimum access level of the MS, and the interference
condition.
6. Late assignment: This function is set at the MSC side. If this function is enabled,
the call is on the SDCCH before the called MS answers. This prolongs the time when the
SDCCH is occupied and thus may cause SDCCH congestion.
7. RXLEV_ACCESS_MIN: If this level is too low, a large number of MSs may access
the network, and SDCCH congestion may occur during call initiation or location update.
In addition, interference signal may be mistakenly regarded as the random access
signals. For details, see Case 3.
8. Tx-integer: When the network traffic is heavy, the success rate of immediate
assignment is low if the sum of S and T is small. Thus, the value of T should be properly
adjusted to make the sum of S and T greater. For details about the value of S, see the
description of Tx-integer.
9. Cell Bar Access (CBA):
0: cell access allowed;
1: cell access prohibited.
Together with CBQ, CBA determines the priority of a cell. For details, see the GSM
04.08 protocol.
CBQ
CBA
Cell Selection
Priority
Cell Reselection
Priority
Normal
Normal
Prohibited
Prohibited
Low
Normal
Low
Normal
2013-7-18
Page 23 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
10. Cell Bar Qualify (CBQ): CBQ takes effect during cell selection rather than cell
reselection.
Objective: to check the problems that exist on site and solve the problems caused by
poor air interface quality and incorrect parameter settings.
The symptoms are listed as follows:
Symptom 1: The number of failed SDCCH seizures due to timeout is almost equal to
the number of location updating requests minus the number of link establishment
indications for location updating.
Symptom 2: The problem happens discontinuously during both busy hours and idle
hours.
Symptom 3: The call service is normal. Except for low immediate assignment
success rate in a few cells during certain periods, the KPIs and drive test result are
normal, and no call drop complaint is received. Because when an MS fails in location
update, it may try to access other cells or try to access the cell again periodically.
Symptom 4: No interference and no cells with the same BCCH frequency and BSIC
exist.
Symptom 5: No abnormality such as uplink-downlink imbalance exists.
Symptom 6: The result of signaling analysis on the Abis interface shows that the
number of request retransmissions and the retransmission interval of the failed location
updates meet the configuration requirements.
If all the previous symptoms exist, you can infer that the problem is low immediate
assignment success rate caused by abnormal location update.
3.2.4.2
Problem Handling
As the problem of low immediate assignment success rate is caused by some MSs,
and the MSs cannot be located because no layer-3 information is provided in location
update procedure, this problem cannot be solved on the network side currently.
To improve the user satisfaction, do as follows:
2013-7-18
Page 24 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
(1) Reduce the impact of abnormal MS location updates on the network KPIs.
(2) Communicate thoroughly with customers.
Problem handling:
If any of the previous six symptoms does not exist, initiate the procedures for
network optimization and troubleshooting.
To perform network optimization according to the RSL signaling, do as follows:
1. If the value of TA in the location update signaling is high and the access level is
low during the time when the problem exists, do as follows:
Adjust the following parameters: Max TA, RACH Min Access Level, and Txinteger (increase S and T).
Increase the length of the following timers: T3101, T3122, T3212, and T3111.
Adjust the cell selection priority by setting the value of CBA and CBQ.
2. For the sites located on the edge of location areas, do as follows to optimize the
location update strategy:
Adjust the parameter Cell Reselection Hysteresis and adjust the cell selection
priority by setting the value of CBA and CBQ.
3. Reduce the MS retransmission times (recommended value: 1) and reduce the
impact of retransmission on the network KPIs.
Data analysis:
1. For the analysis report of problem location, see the following attachment.
Analysis on Low Immediate Assignment Success Rate Caused by Abnormal MS Location Update-qiuwenfang.rar
Based on the previous analysis, we find that the channel requests received when the
problem occurred were sent by some abnormal MSs, and the BTS responded and
handled the requests correctly. The analysis is based on the uplink and downlink. The
details are described as follows:
2. Uplink channel requests from the MS
(1) When the cell access is prohibited, the immediate assignment success rate of the
cell becomes normal. This indicates that the abnormal location updates are caused by
the MS rather than the interference.
(2) The location update requests are with high level, low error rate, and small TA
2013-7-18
Page 25 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
(except for some sites with wide coverage area). This indicates that the abnormal
location updates are initiated by the MS.
(3) The number of location update requests sent by an MS complies with the settings
of network parameters. This also indicates that the abnormal location updates are
initiated by the MS.
3. Downlink immediate assignment
(1) The immediate assignment commands are sent correctly, because the values of
T1, T2, and T3 are the same as those in the channel requests.
(2) Call access and the supplementary services such as short message are all
normal. The problem only exists in the SDCCH access related to location update. This
indicates that the immediate assignment commands are sent correctly.
4. Network data comparison (for the swapped offices and the offices with segmental
networking)
By comparing the data before and after swapping (for swapped offices) and the data
of the surrounding cells (for the offices with segmental networking), we find that the
problem also exists in the networks of other companies.
4 Test Method
Immediate assignment success rate is a traffic measurement counter.
As the formulae of this counter in different manufacturers and operators are different
currently, you should record the value of other related counters and choose a proper
formula according to the actual conditions.
2013-7-18
Page 26 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
Rate Optimization
5.1
Problem description
The SDCCH congestion rate of cell 2 in S1/1/1 configuration was higher than 8%,
and the immediate assignment success rate of that cell was 90%.
Cause analysis and handling
(1) The measurement counters of the TCH and SDCCH shows that the traffic volume on
the TCH is low, and the traffic volume per cell in busy hours is lower than 2.2 Erl; however,
there are many SDCCH seizure requests (3032 in busy hours), the traffic volume on the
SDCCH is 1.86 Erl, and the congestion rate is higher than 8%.
(2) The SDCCH is mainly occupied by the signaling before the call is established,
the signaling during handover, the signaling for location update in idle mode, and the
short messages.
(3) As the traffic volume on the TCH, the number of TCH seizure requests (318), and
the number of handover requests (146) are all normal, we infer that the high SDCCH
seizure rate may be caused by too frequent location updates or too many short
messages.
(4) The LAC of the cell is 0500, but the LACs of other cells around this cell are all
0520. After the LAC of the cell is changed to 0520, the number of SDCCH seizure
requests becomes 298, the traffic volume on the SDCCH becomes 0.27 Erl, the
congestion rate decreases to 0, and the immediate assignment success rate reaches up
to 95%.
2013-7-18
Page 27 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
5.2
INTERNAL
Problem description
The immediate assignment success rate was low in a local network. Traffic statistics
showed that the problem was mainly caused by SDCCH congestion on some sites.
5.3
Problem description
Subscribers of the cells controlled by a certain BSC complained that the success
rate of random access was low.
2013-7-18
Page 28 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
When Random Access Error Threshold and RACH Min Access Level are
set to 200 and 1 respectively, the mean immediate assignment success rate of
all the cells is 97.9% an hour later;
When Random Access Error Threshold and RACH Min Access Level are
set to 200 and 0 respectively, the mean immediate assignment success rate of
all the cells is 91.92% an hour later;
When Random Access Error Threshold and RACH Min Access Level are
set to 180 and 1 respectively, the mean immediate assignment success rate of
all the cells is 97.24% three hours later.
After discussing with the customer, we decide to set Random Access Error
2013-7-18
Page 29 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
Threshold and RACH Min Access Level of all the cells to 180 and 3
respectively. In this way, mean immediate assignment success rate of all the
cells is higher than 98.6%.
5.4
Problem description
The personnel on site reported that the immediate assignment success rate of some
cells was low.
(3) The signaling of the cells with problem shows that generally the value of TA is
2013-7-18
Page 30 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
small and the level is high. This indicates that the problem is not caused by interference.
But after the BSS sends the immediate assignment command and waits for the MS to
access, the uplink signal strength detected by the BTS is always lower than 110 dBm.
This indicates that the MS does not report the link establishing indication and thus
causing the immediate assignment failure.
2013-7-18
Page 31 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
Page 32 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
(5) For a swapping project, check whether the problem exists in the network before
swapping. If the problem existed, then we can infer that the problem is mainly
related to the MS.
Onsite
Information
that
Needs
to
Be
Obtained
1. Traffic statistics of the network during one week before and after the problem
occurred.
BSC32:
(1) All the counters of the Access Capability Measurement 1 and Access
Capability Measurement 2 in BSC Overall Performance Measurement;
(2) All the counters of Receive Quality Performance Measurement;
(3) All the counters of the SDCCH Assignment Performance Measurement
and TCH Assignment Performance Measurement in Channel Assignment
Performance Measurement;
BSC6000:
2013-7-18
Page 33 of 34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual
INTERNAL
(1) All the counters of Access Measurement per BSC in BSC Measurement;
(2) All the counters of Interference Band Measurement per TRX and Receive
Quality Measurement per TRX in MR Measurement;
(3) All the counters of Channel Configuration Measurement per Cell in
Channel Measurement;
(4) All the counters of KPI Measurement per Cell, Immediate Assignment
Measurement per Cell, and Flow Control Measurement per Cell in Call
Measurement.
2. Data configuration and OMC data operation logs before and after the problem
occurred.
3. Data configuration file and engineering parameters table.
4. Whether the network optimization operations, such as antenna adjustment,
frequency adjustment, and location area adjustment, are performed after the problem
occurred.
5. Alarms generated before and after the problem occurred, including commissioning
alarms.
2013-7-18
Page 34 of 34