UNIVERSITY OF TRIPOLI
FACULTY OF ENGINEERING
Electrical and Electronic Engineering Department
Subject: Data Communications and Networking Date: 8-1-2013
Course Code, :- EE524 Midterm Exam I Solution
Fall 2012 ime: 1.5 hours
PART 1 MCO QUESTIONS Right answer 3 marks wrong answer 1 miark)
QU. _During the movement of the frame,
a b | The logical addresses will change but
the physical addresses remain the same
| The port addresses will change but the |d | None of the above
logical addresses remain the same
Q2. _If the channel bandwidth increases,
'a|_The bite rate decreases fb h
ic | The bite rate will not affected id | None of the above
Q3. _If the codeword contains 5 bits and the dataword contains 2 bit we can,
la | Check only one bit error [b | correct two bit error
ic | Correct one bit error id
Q4. ‘The purpose of establishing layered modules is,
a [b | To make the cost much cheaper,
To make network independent on hardware [d | None of the above
ec
QS. In OSI module,
fa] Each layer add header and pass the data to _[b | Each layer add tail and pass the data
the upper layer to the upper layer
e (d | None of the above
Q6. ‘The layers in OSI module talk physically,
To its peer in the destination host b
id
fa
je] To the upper layer onl ‘None of the above
QJ. _ Shannon capacity =
Defines the bit rate of a noiseless channel [b PURCIECW WS Sinaliy
Determines the bit rate of a noisy channel__|d | None of the above
Self synchronization is obtained b ER
8 zeros are replaced by 000—+0-+ always _[d | None of the above
a
le
Q8. _In Bipolar with 8-Zeros Substitution line code
a
le
Q9. The maximum number of bits exist in a link at a time is 2 bits. If the bit rate
‘a | The total link delay is | milliseconds (b | Maximum delay is 0.5 mi
ic | Minimum delay is 2 milliseconds d NGHEE!
QU0._The minimum hamming distance between these
a 2
c 4
of | RaePART 2 GENERAL QUESTIONS,
Q11. A 20 MHz channel is used to transmit digital data using a signal has 8 levels. Suppose the
used bite rate 80% of the maximam possible bite rate. what is the minimum signal to noise
ratio 2 )
R=2B logl =2 x20 x 10° x log,8 = 40 x 10° x 3 = 120 MBPS
= =a m_
R= 08x C 3C=Te ae 7 150 MBPS
= p SNR 3X6 _ 3150x106 _
C= BEE > SNRyp = 22S = AI _ ops ap
SNR = 1072/30 = 177,83
Q12. Sketch the following data ~ 1001000010" as
i) NRZ-I with SOMBPS
T, =2=—
DR Sox108
1, = 20ns
ii) Differential Manchester encoding with 100 MBPS
222
Dole 10010
Ty = 10ns
iii) HDB3 with 100 MBPS
Ty = R= Fooxio®
10ns
Q13.
Byr
The
and the bits in the last row shows the vertical parity checks.
From the table we have an error in the second row and the
seco
So we have one etror in the second bit of the second byte.
A system uses two dimensions parity check code C(40.28). The following data was
received, “110011 11MM 11007 0QMMMMBGO110101°. Examine the received data
fiom the error point of view
‘eorganizing the received data in 5 rows and 8 columns table.
bits in the last column shows the horizontal parity checks
nd column
GOOD LUCK FOR EVERY BODY ___
DR. T. BENMUSA
2of2inie