Professional Documents
Culture Documents
Fax PDF
Fax PDF
D DRIVELINE/AXLE
B
SECTION
FRONT AXLE C
FAX
E
CONTENTS
PRECAUTIONS .......................................................... 2 FRONT WHEEL BEARING ................................... 5 F
Precaution ................................................................ 2 Components ............................................................. 5
PREPARATION ........................................................... 3 Removal and Installation .......................................... 5
Special Service Tools ............................................... 3 REMOVAL ............................................................. 5 G
Commercial Service Tools ........................................ 3 INSTALLATION ..................................................... 6
NOISE, VIBRATION, AND HARSHNESS (NVH) Disassembly and Assembly ...................................... 6
TROUBLESHOOTING ................................................ 4 DISASSEMBLY ..................................................... 6
H
NVH Troubleshooting Chart ..................................... 4 INSPECTION AFTER DISASSEMBLY .................. 6
ASSEMBLY ........................................................... 6
2WD SERVICE DATA AND SPECIFICATIONS (SDS) ........ 7
Wheel Bearing .......................................................... 7 I
FRONT WHEEL HUB AND KNUCKLE ...................... 5
On-Vehicle Inspection .............................................. 5
J
FAX-1
PRECAUTIONS
PRECAUTIONS PFP:00001
Precaution EDS000EM
SBR686C
FAX-2
PREPARATION
PREPARATION PFP:00002
A
Special Service Tools EDS000EN
Tool name
Description
Tool number B
Drift C
KV38104010 Installing hub assembly
a: 67 mm dia.
b: 49 mm dia.
FAX
ZZA1051D
E
Drift
KV38100500
Installing wheel bearing
a: 80 mm dia.
b: 60 mm dia. F
ZZA0701D
S-NT360 J
FAX-3
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
NVH in WT section.
NVH in WT section.
NVH in PS section.
Refer to FAX-5
Refer to FAX-5
Reference page
ROAD WHEEL
STEERING
TIRES
Noise
Shake
Vibration
Symptom FRONT AXLE
Shimmy
Judder
Poor quality ride or handling
: Applicable
FAX-4
FRONT WHEEL HUB AND KNUCKLE
[2WD]
FRONT WHEEL HUB AND KNUCKLE
[2WD] PFP:40202
A
On-Vehicle Inspection EDS000EO
Check front axle for excessive play, cracks, wear, or other damage.
Move front wheel (right/left), and check for play. B
Confirm that nails or equivalents are not stuck in wheels.
Retighten all axle nuts and bolts to specified torque.
C
FRONT WHEEL BEARING
Lift vehicle, and check the following.
Move wheel hub in axial direction by hand, and check front wheel bearing for looseness. If looseness is FAX
detected, check and adjust front wheel hub assembly.
Axial end play : 0 mm (0 in)
E
Rotate wheel hub, and check for unusual noise. If any, replace wheel bearing.
Components EDS000EP
SDIA0500E
REMOVAL
1. Remove cotter pin. Using a hub lock nut wrench (special service
tool), and remove lock nut.
2. Remove caliper from knuckle. Using a wire, hang it aside.
CAUTION:
While brake caliper is removed, do not depress brake pedal.
3. Remove cotter pin from tie rod ball joint, and remove tie rod lock
nut.
4. Using a ball joint remover (commercial service tool), remove tie
rod from knuckle. During removal, be careful not break ball joint
boot. RAC0197D
CAUTION:
Ball joint remover (commercial service tool) may come off suddenly. Therefore, temporarily
tighten lock nut.
5. Remove bolts securing upper arm to knuckle and lower arm to knuckle.
FAX-5
FRONT WHEEL HUB AND KNUCKLE
[2WD]
INSTALLATION
Install in reverse order of removal.
Disassembly and Assembly EDS000ER
DISASSEMBLY
1. Remove wheel bearing lock nut.
2. Remove bearing hub bolt, and remove hub bearing assembly.
SDIA0502E
SDIA0393E
FAX-6
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX
FAX-7
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-8