Test Databank Print
D:\TestGen\CSWIP 2006 Questions Set 11 .mdb
1 Oxy fuel gas may be used for which of the following?
A. Pre- heating
B. PWHT
. Cutting
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 10
2 Ifa pressurized cylinder was left in the horizontal position ,how long should it left in
the upright position before it can be safely used?
A. Minimum of 20 minutes
B. Mi jum of 40 minutes
C. Minimum of 10 minutes
D. Minimum of 60 minutes
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 20
3 Whatiis the highest temperature achievable when acetylene is combusted with
oxygen?
A. 3200C
B. 3000C
c. 25006
D. 2000¢
E.
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 304 When using Oxy - Acetylene and oxidizing flame is used for mainly what type of
1g?
A. Stainless steel welding
B. Bronze welding
C. Carbon steel welding
D. All of the above
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question ID: 40
5 When using Oxy - Acetylene a carburizing flame is used for mainly what type of
welding?
A. Stainless steel welding
B. Hard facing welding
C. Bronze welding
D. None of the above
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question 1D: 50
6 _ Oxy-Fuel gas cutting method is dependant on which of the following?
A. Gas
B. Nozzle
C. Pressure
D. All of the above
E.
Correct Answer: D
Reference:
Media Typ
Media Location:
Question 1D: 607 Which of the following are types of plasma cutting processes?
A. Transferred are
B. Non transferred arc
C. Sub are
D. Both A and B are correct
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 70
8 It is the duty of the welding inspector to ensure that which of the following safe
working practices are carried out?
A. Welding/cutting process safety
B. Safe use of lifting equipment
C. Safe use of hand tools
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 80
9 When working with electrical power we must ensure a good working practice and
be especially vigilant in?
A. Wet
B. Damp
C. Low supply voltage will be used (110V)
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 9010 Which types of arc cutting and gouging are generally used?
A. Conventional cutting/gouging electrodes
B. Oxy-are cutting/gouging
C. Arc air-air cutting/gouging
D. All of the above
E.
Correct Answer: D
Reference:
100
11 Which type of material is used for the consumable for Arc - Air cutting/gouging?
A. Carbon steel coated
B. Stainless steel coated
C. Copper coated
D. Manganese coated
E.
Correct Answer: c
Reference:
Media Type
Media Location:
Question ID: 110
12 When considering any type of weld cracking mechanism which elements must be
present for its occurrence?
A. Stress
B. Restraint
C. Susceptible microstructure
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID:
12013. The minimum critical factors for hydrogen cracking could be which of the
following?
A. Hydrogen content more than 15m for every 100 gm of deposited weld metal
B. Hardness more than 350 VPN
C. Temperature less than 300¢
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 130
14 To control hydrogen cracking which of the following could be carried out?
Pre - heating
Rapidly cool the steel
Heat the steel above the critical temperature
The creation of martinsite in the grain structure would avoid any hydrogen
cracking
pomp
E.
Correct Answer: A
Reference:
Media Type:
Media Location:
Question 1D: 140
15 Elements to be considered when pre - heating are which of the following?
A. Hardenability
B. Arc energy
C. Thickness
D. All of the above
E.
Correct Answer: D
Reference:
Media Location:
Question ID: 15016
7
18
Higher carbon steel will have which of the following?
‘A. Large amount of ductility
B. Very little ductility
C. Carbon will have no effect on ductility
D. Higher the carbon more the ductility
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question ID: 160
Sol
ication cracking is caused generally by which condition?
A. High sulpher content
B. High carbon content
C. High hydrogen content
D. High quenching of the steel
m
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 170
Careful consideration must be given to the Mn/S ratio, which should be in the
region of which of the following?
A. 30:4
B. 25:1
C. 10:1
D. 40:1
Gs
Correct Answer: D
Reference:
Media Type:
Media Location:
Question 1D: 18019 Which types of steels are particularly prone to solidification cracking?
A. Carbon steel
B. Chrome moly
C. Ferretic stainless steel
D. Austenitic stainless steel
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 190
20 Lamellar tearing could be caused in which type of joint configurations?
A. Corner joints
B. Butt joints
C. T joints
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 200