Professional Documents
Culture Documents
Construction PDF
Construction PDF
For
2
1910, 1926
Construction Safety Policy
Table of Contents
I. Objective
II. Policy
III. Applicability
IV. Implementation
V. Administration
VI. Reporting Injuries
VII. Notifications
VIII. Basic Safety Rules
IX. Enforcement of Safety Policy
X. Attachments
A. Job Safety Checklist
B. Safety Equipment Checklist
C. Safety Meeting Report
D. Employee Acknowledgment
3
(Company Name)
Safety Policy
I. OBJECTIVE
Compliance with the following Safety Policy and all items contained therein is mandatory for all
employees of the company. The authorization and responsibility for enforcement has been given
primarily to the Responsible Person . The Other Responsible Person(s) share in this
responsibility as well.
II. POLICY
It is company policy that accident prevention be a prime concern of all employees. This includes
the safety and well being of our employees, subcontractors, and customers, as well as the
prevention of wasteful, inefficient operations, and damage to property and equipment.
III. APPLICABILITY
Every employee is expected to comply with the Safety Policy, as well as OSHA Health and
Safety Standards.
IV. IMPLEMENTATION
This Safety Policy supports six fundamental means of maximum employee involvement:
4
E. Audio and/or visual safety presentations given at jobsites by Responsible Person .
F. Various incentive awards for exemplary safety performance.
The Responsible Persons will meet at least once a month to evaluate all areas of safety and
make recommendations to the company president.
V. ADMINISTRATION
The Safety Policy will be carried out according to guidelines established and published in this
and other related procedures. Specific instructions and assistance will be provided by
Responsible Person as requested. Each supervisor will be responsible for meeting all of the
requirements of the Safety Policy, and for maintaining an effective accident prevention effort
within his or her area of responsibility. Each supervisor must also ensure that all accidents are
thoroughly investigated and reported to Responsible Person(s) on the same day of the
occurrence.
All employees will be held accountable for filling out a Notice of Injury Form" immediately
after an injury occurs, even if medical treatment is not required. (Notice must be made at or near
the time of the injury and on the same day of the injury.) Employees must report the injury to
their supervisor/leadman/foreman/superintendent/project manager, etc. A casual mentioning of
the injury will not be sufficient. Employees must let their supervisor know:
Failure to report an injury immediately (meaning at or near the time of the injury and on the same
day of the injury) is a violation of the Safety Policy, and may result in immediate termination, in
accordance with company policy.
VII. NOTIFICATIONS
After the injured has been taken to the hospital, the leadman/foreman/supervisor shall
notify the main office and Responsible Person(s) as soon as possible. Statements from
witnesses shall be taken. Statements are to be signed by witnesses and should include the
time and date. Photographs of the area where the incident occurred and any other relevant
5
items are to be taken. Responsible Person will assist in the investigation. The
completed accident report form will be sent to the main office.
A. Compliance with applicable federal, state, county, city, client, and company safety
rules and regulations is a condition of employment.
B. All injuries, regardless of how minor, must be reported to your supervisor and the
Safety Office immediately. An employee who fails to fill out a "Notice Of Injury
Form" and send it to the Safety Office can be issued a safety violation notice and may
be subject to termination, in accordance with company policy. In the event of an
accident involving personal injury or damage to property, all persons involved in any
way will be required to submit to drug testing.
C. Hard hats will be worn by all employees on the project site at all times. The bill of
the hard hat will be worn in front at all times. Alterations or modifications of the hat
or liner are prohibited. Crane operators, when in an enclosed cab, have the option of
not wearing a hard hat due to the possible obstruction of view.
D. Safety glasses will be worn as the minimum-required eye protection at all times.
Additional eye and face protection such as mono-goggles and face shields are
required for such operations as grinding, jack hammering, utilizing compressed air or
handling chemicals, acids and caustics. Burning goggles for cutting, burning or
brazing and welding hoods for welding, etc., are required.
1. Full body harnesses and lanyards shall be worn and secured any time there is a fall
hazard of more than six (6) feet.
2. Lifelines shall be erected to provide fall protection where work is required in areas
where permanent protection is not in place. Horizontal lifelines shall be a
minimum of 2-inch diameter wire rope. Vertical lifelines shall be 3/4 inch manila
rope or equivalent and shall be used in conjunction with an approved rope grab.
3. Structural steel erectors are required to "hook up" with full body harness and
lanyard.
6
4. Employees using lanyards to access the work or position themselves on a wall or
column, etc., must use an additional safety lanyard for fall protection.
5. Manlifts must be used properly. As soon as an employee enters an articulating
boom lift and before the lift is started, the employee must put on the harness and
attach the lanyard to the lift. Employees are not required to wear harnesses on
scissor lifts.
F. Clothing must provide adequate protection to the body. Shirts must have at least a tee
sleeve. Shirts with sleeves and long pants will be worn at all times. No shorts are to
be worn on projects. All employees, except welders and burners, must tuck shirt tails
inside trousers. Burners and welders will not be permitted to wear polyester or nylon
clothing. Sturdy work boots with rigid, slip resistant soles are required. No clogs,
tennis shoes or loafers are permitted. Steel-toed tennis shoes with the ANSI label are
the only alternative to the leather work boot.
H. Firearms, alcoholic beverages or illegal drugs are not allowed on company property or
in company vehicles at any time. When drugs are prescribed by a physician, the
Responsible Person must be informed. The use or possession of illegal drugs or
alcoholic beverages on the jobsite will result in immediate termination.
J. Burning and cutting equipment shall be checked daily before being used. Flash back
arresters shall be installed at the regulators on both oxygen and LP bottles. All gas
shall be shut off and hoses disconnected from bottles and manifolds at the end of the
work day. Caps shall be replaced on bottles when gauges are removed. When gauges
are removed and caps replaced, the oxygen and LP bottles shall be separated into
storage areas no less than 20 feet apart with a No Fire or Smoking" sign posted and a
fire extinguisher readily available. Makeshift field repairs will not be allowed.
K. Drinking water containers are to be used for drinking water and ice only. Tampering
with or placing items such as drinks in the water cooler will result in immediate
termination. The "common drinking cup" is not allowed. Only disposable cups will
be used.
7
mushroomed heads, hammers with loose or split handles, guards missing on saws or
grinders, etc.
M. All extension cords, drop cords, and electrical tools shall be checked, properly
grounded with ground fault interrupters (GFIs), and color-coded by a designated
competent person each month. This shall be part of the assured grounding program.
Cords and equipment that do not meet requirements shall be immediately tagged and
removed from service until repairs have been made.
O. Glass containers or bottles of any kind are not permitted on jobsites or in company
vehicles.
P. The jobsite speed limit is 10 MPH. No employee is permitted to ride in the bed of a
truck standing up or sitting on the outside edges of a truck. Employees must be sitting
down inside the truck or truck bed when the vehicle is in motion. Riding as a
passenger on equipment is prohibited unless the equipment has the safe capacity for
transporting personnel.
Q. Adequate precautions must be taken to protect employees and equipment from hot
work such as welding or burning. Fire extinguishing equipment shall be no further
than 50 feet away from all hot work. Used fire extinguishers must be returned to
(Responsible Person) to be recharged immediately. Use of welding blinds is
required in high traffic areas.
R. All scaffolding and work platforms must be built and maintained in accordance with
OSHA specifications. All ladders must be in safe condition without broken rungs or
split side rails. Damaged ladders shall be removed from service. Ladders shall be
secured at the top and bottom and extend three (3) feet past the working surface.
Metal ladders around electrical work are prohibited. A step ladder shall never be used
as an extension ladder. A step ladder must only be used when fully opened with
braces locked.
8
U. All floor openings or excavations shall be barricaded on all sides to ensure employees
are aware of the hazards. Floor holes shall be covered, with the covers secured and
clearly marked.
V. Warning signs, barricades, and tags will be used to the fullest extent and shall be
obeyed.
1. Green tags are to be placed on 100 percent complete scaffolds with all braces,
locks and hand, mid, and toe rails in place before use.
2. Yellow tags indicate incomplete scaffolds. If scaffold is missing a hand, mid, or
toe board, it must have a yellow tag and employees on it must be tied off at all
times.
3. Red tags indicate scaffolds that are in the process of either being erected or
disassembled. These scaffolds are not to be used at any time.
4. Scaffold tags should be placed in a highly visible location on the scaffolds for
all employees to see.
X. All OSHA Safety Standards will be followed for job processes requiring respiratory
protection. SEE RESPIRATORY PROTECTION PROGRAM.
Z. All OSHA Safety Standards concerning confined space entry will be followed. *SEE
CONFINED SPACE PROGRAM.
AA. All OSHA Safety Standards concerning lockout/tagout of energized equipment will
be followed. *SEE LOCKOUT/TAGOUT PROGRAM
BB. All OSHA Safety Standards will be followed for job processes requiring fall
protection. *SEE FALL PROTECTION PROGRAM.
*These sample written programs can be downloaded from the Frankenmuth Safety Services
Website.
Safety violation notice(s) shall be issued to any employee, subcontractor, or anyone on the jobsite
violating the safety rules or regulations by Responsible Person .
9
B. Any employee receiving three (3) written general violations within a six (6) month
period shall be terminated.
C. Issuance of a safety violation notice for failure to use fall protection or for failure to
report a job injury (at the time of the injury) may result in immediate termination, in
accordance with company policy.
It is understood that Company Name is not restricting itself to the above rules and
regulations. Additional rules and regulations as dictated by the job will be issued and posted as
needed.
10
ATTACHMENT A
The following Job Safety Checklist has been condensed and edited from the Occupational Safety
and Health Act, Part 1926, Construction Safety and Health Regulations.
A. Safety Rules
B. Recordkeeping
_________ OSHA poster "Safety and Health Protection on the Job" posted.
_________ OSHA " 200 Log or Occupational Injuries and Illnesses posted during the month of
February only.
_________ Hard hat sign posted in a conspicuous manner.
_________ Weekly safety meeting sign-in logs maintained in a folder with a copy forwarded
to the main office weekly.
11
_________ Adequate supply of drinking water.
_________ Sanitary facilities adequate and clean.
_________ Adequate ventilation.
D. First Aid
_________ First aid stations with supplies and equipment. The expiration dates of supplies
checked monthly. Expired supplies discarded.
_________ Trained first aid personnel.
_________ Injuries promptly and properly reported.
F. Fire Protection
12
I. Electrical
_________ All portable tools and cords properly grounded [Ground Fault Interrupters (GFI=s)
properly installed].
_________ Daily visual inspection of caps, ends and cords for deformed or missing pins,
insulation damage and internal damage.
_________ Tests of cords, tools and equipment for continuity and correct attachment of the
equipment grounding connector (GFI) to the proper terminal made every month
and:
1. Prior to first use.
2. Prior to return to service after repairs.
3. Prior to return to service after incident that may have caused damage to
cord or equipment.
_________ Cords and equipment not meeting requirements immediately tagged and removed
from service until repairs have been made.
J. Ladders
K. Scaffolding
_________ Guardrails, handrails and covers installed wherever there is danger of employees or
materials falling through floors, roots or wall openings and shall be guarded on all
exposed sides.
_________ Posts at least 2 x 4 stock and spaced no more than eight (8) feet apart.
13
_________ Top rail 42 inches above the floor and of 1 x 4 stock.
_________ Intermediate rail 21 inches above the floor and of 1 x 4 stock.
_________ Guardrail assemblies around floor openings equipped with toe boards. Toe boards at
least four (4) inches above the floor level with no more than 1/4 inch clearance above
the floor level, when there are employees below or when conditions dictate.
_________ Hole covers permanently attached to the floor or structure and identified with a hole
cover sign stenciled with the word "Danger". Hole covers for holes two (2) inches or
greater in diameter made of at least 3/4 inch plywood or heavier.
M. Material Hoists
N. Motor Vehicles
_________ Material at least two (2) feet from edge of excavation site.
_________ Proper temperature and moisture levels for safe storage of materials to prevent
deterioration or volatile hazards within the storage area.
_________ Inventory maintained and inspected frequently.
_________ Proper protective gear worn when handling chemicals.
_________ Full body harnesses as positioning devices for employees tying rebar greater than six
(6) feet above adjacent working surface have
_________ Automatic shut-off switches on trowel machines.
14
_________ No riding on concrete buckets or flying forms.
_________ All forms properly shored.
_________ Single post shores braced horizontally.
_________ Prohibition of the use of cranes or derricks to hoist employees on a personal platform
except in the situation where no safe alternative is possible.
15
ATTACHMENT B
The following is a list of Safety Equipment that should be on the job, if required, or available
from the Responsible person at all times. Equipment should be checked at intervals in
accordance with the applicable OSHA Safety Standards by the Superintendent to ensure that all
required equipment is present and in good condition.
16
ATTACHMENT C
A safety meeting report is signed to indicate attendance. The form has room for employees to
sign after attending their weekly safety meeting. This form shall be filled out for each jobsite
safety meeting that is held. After completion of the form, make a copy to maintain at each
jobsite and return the signed original copy to the main office.
Topic:___________________________________
17
ATTACHMENT D
EMPLOYEE ACKNOWLEDGMENT
I state that I have attended the safety orientation, and have read and received a copy of the
Company Name safety rules and regulations.
I further state that I understand these rules and acknowledge that compliance with the safety rules
and regulations is a condition of employment. If I violate the safety rules or fail to report an
injury to my supervisor immediately, I understand that I am subject to termination, in accordance
with company policy.
__________________________________________
EMPLOYEE SIGNATURE
__________________________________________
DATE
__________________________________________
Responsible Person SIGNATURE
__________________________________________
DATE
cc: Supervisor
The information and suggestions contained in this material have been developed
from sources believed to be reliable. However, Frankenmuth accepts no legal
responsibility for the correctness or completeness of this material, or its
application to specific factual situations.
18