Professional Documents
Culture Documents
Performance Sheet Drill Pipe: Pipe Body: Tubular Assembly
Performance Sheet Drill Pipe: Pipe Body: Tubular Assembly
Tensile Strength (lbs): 617,041 583,816 550,841 485,641 Upset Type: IEU Fluid Capacity w/o IPC (gal/ft): 0.57
Torsional Strength (ft-lbs): 57,506 54,346 51,218 45,060 Max Upset OD (in): 4.688 Fluid Capacity w/o IPC (bbls/ft): 0.0136
Drift Size (in): 3.125
Burst Capacity (psi): 18,348 19,920 18,872 16,775
Collapse Capacity (psi): 17,228 15,747 14,244 11,168
18
0
Note: These are OEM values that may vary with actual values due to mill tolerances, IPC tolerances, OEM rounding, and other
Notes: Body properties are calculated based on uniform OD and wall thickness. factors. Pipe is purchased at a guaranteed 95% RBW. IPC is applied to a nominal thickness of 0.009''. Pipe will have an ID of
Burst capacity for Nominal (100% RBW) based on 87.5% RBW per API. 3.771'', which is smaller than pipe purchased at 87.5%.
Internal Pressure Rating (psi): 15,000 Tool Joint Torsional Strength (ft-lbs): 32,400
External Pressure Rating (psi): 10,000 Tool Joint Tensile Strength (lbs): 611,100
CTM43 is a trademark of NOV Grant-Prideco. Note: Elevator capacity based on assumed elevator bore, no wear factor, and contact stress of 110, 100 psi. An increased
Note: MUT values are based on a friction factor of 1.0. elevator shoulder OD increases elevator capacity without affecting make-up torque.
The technical information containted herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical
information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various
inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices,
and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
www.workstringsinternational.com 08-Sep-15
Download the Workstrings International Pipe Specification App on the App Store or Google Play
Operational Limits of Drill Pipe
Connection CTM43 Tool Joint OD (in) 5.250 Tool Joint ID (in) 3.250 Tool Joint Specified Minimum 120,000
Yield Strength (psi)
Pipe Body 80 % Inspection Class Pipe Body OD (in) 4.5 Wall Thickness (in) 0.337 Pipe Body Grade Z-140
Combined Loading for Drill Pipe at Combined Loading for Drill Pipe at
Maximum Make-up Torque = 19,400 (ft-lbs) Minimum Make-up Torque = 16,200 (ft-lbs)
Operational Assembly Pipe Body Connection Max Operationa Assembly Pipe Body Connection
l Torque Max Tension Max Tension Max Tension
Torque Max Tension Max Tension Tension
(ft-lbs) (lbs) (lbs) (lbs) (ft-lbs) (lbs) (lbs) (lbs)
Connection
Make-up Torque Range
Make-up Torque Connection Max
(ft-lbs) Tension (lbs)
Min MUT 16,200 585,300
16,600 599,700
16,900 610,600
17,300 595,900
17,600 584,100
18,000 568,300
18,300 556,500
18,700 540,700
19,000 528,800
Max MUT 19,400 513,000
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
06-17-2015