Professional Documents
Culture Documents
Datasheet Cua KIT MSP430G2553 Rev 1 - 4 PDF
Datasheet Cua KIT MSP430G2553 Rev 1 - 4 PDF
User's Guide
List of Figures
1 MSP-EXP430G2 LaunchPad Overview .................................................................................. 5
2 Insert Device Into Target Socket .......................................................................................... 8
3 Code Composer Studio v4 in Debugging Mode ...................................................................... 9
4 MSP-EXP430G2 LaunchPad With Attached eZ430-RF2500 Target Board ....................................... 10
5 Device Pinout .............................................................................................................. 13
6 Schematics, MSP-EXP430G2 Emulator (1 of 2), Revision 1.4 ...................................................... 14
7 Schematics, MSP-EXP430G2 Emulator (2 of 2), Revision 1.4 ...................................................... 15
8 Schematics, MSP-EXP430G2 Target Socket, Revision 1.4 ......................................................... 16
9 Schematics, MSP-EXP430G2 Emulator (1 of 2), Revision 1.5 ...................................................... 17
10 Schematics, MSP-EXP430G2 Emulator (2 of 2), Revision 1.5 ...................................................... 18
11 Schematics, MSP-EXP430G2 Target Socket, Revision 1.5 ......................................................... 19
12 Layout, LaunchPad Top Layer ........................................................................................... 20
13 Layout, LaunchPad Bottom Layer ....................................................................................... 21
14 Layout, LaunchPad Silkscreen .......................................................................................... 22
List of Tables
1 Jumper Connection J3 Between Emulator and Target................................................................. 9
2 eZ430 Debugging Interface .............................................................................................. 10
3 Supported Devices ........................................................................................................ 11
4 Features Supported by On-Board Emulator ........................................................................... 13
5 Bill of Materials............................................................................................................. 23
1.1 Overview
The MSP-EXP430G2 LaunchPad is an inexpensive and simple evaluation kit for the MSP430G2xx Value
Line series of microcontrollers. It is an easy way to start developing on the MSP430 with on-board
emulation for programming and debugging as well as buttons and LEDs for a simple user interface.
Rapid prototyping is simplified by the 20-pin BoosterPack headers which support a wide range of available
BoosterPack plug-in modules. You can quickly add features like wireless connectivity, graphical displays,
environmental sensing, and much more. You can either design your own BoosterPack or choose among
many already available from TI and third party developers.
The LaunchPad features an integrated DIP target socket that supports up to 20 pins, allowing MSP430
Value Line devices to be plugged into the LaunchPad board. The MSP-EXP430G2 LaunchPad comes
with an MSP430G2553 device by default. The MSP430G2553 has the most memory available of the
compatible Value Line devices.
The MSP430G2553 16-bit MCU has 16KB flash, 512 bytes RAM, up to 16-MHz CPU speed, 10-bit ADC,
capacitive touch enabled I/Os, universal serial communication interface, and more plenty to get you
started in your development.
Free software development tools are also available: TI's Eclipse-based Code Composer Studio IDE
(CCS), IAR Embedded Workbench IDE (IAR), and the community-driven Energia open source code
editor. More information about the LaunchPad, including documentation and design files, can be found on
the tool page at http://www.ti.com/tool/msp-exp430g2.
4 MSP-EXP430G2 LaunchPad Evaluation Kit SLAU318E July 2010 Revised March 2014
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
www.ti.com MSP-EXP430G2 LaunchPad Overview
1.2 Features
MSP-EXP430G2 LaunchPad features:
USB debugging and programming interface featuring a driverless installation and application UART
serial communication with up to 9600 Baud
Supports MSP430G2xx2, MSP430G2xx3, and MSP430F20xx devices in PDIP14 or PDIP20 packages
(see Section 4.7 for a complete list of supported devices)
Two general-purpose digital I/O pins connected to green and red LEDs for visual feedback
Two push button for user feedback and device reset
Easily accessible device pins for debugging purposes or as socket for adding customized extension
boards
High-quality 20-pin DIP socket for an easy plug-in or removal of the target device
SLAU318E July 2010 Revised March 2014 MSP-EXP430G2 LaunchPad Evaluation Kit 5
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
Installation www.ti.com
1.4 Revisions
The first production revision of the LaunchPad in 2010 was 1.3. In 2012 the LaunchPad board revision
changed from 1.4 to 1.5 to align with the new release of Value Line devices. The differences in the
schematic and the kit contents are:
Layout and Schematic:
Voltage feedback in the emulator changed to increase startup stability (Rev 1.3 to Rev 1.4)
Rearranged jumper J3 to support two UART configurations: vertical (SW UART), horizontal (HW
UART)
VCC on the connector J4 can now be disconnected from the emulator VCC by J3
Pullup resistor R34 and capacitor C24 on P1.3 removed to reduce the current consumption
Presoldered male headers J1 and J2
2 Installation
The MSP-EXP430G2 LaunchPad installation consists of three easy steps:
1. Download the required software.
2. Install the selected IDE.
3. Connect the LaunchPad to the PC.
Then the LaunchPad is ready to develop applications or to use the pre-programmed demo application.
6 MSP-EXP430G2 LaunchPad Evaluation Kit SLAU318E July 2010 Revised March 2014
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
www.ti.com Getting Started With MSP-EXP430G2 LaunchPad
SLAU318E July 2010 Revised March 2014 MSP-EXP430G2 LaunchPad Evaluation Kit 7
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
Develop an Application With the MSP-EXP430G2 LaunchPad www.ti.com
The following example for Code Composer Studio shows how to download and debug the demo
application described in Section 3.2.
8 MSP-EXP430G2 LaunchPad Evaluation Kit SLAU318E July 2010 Revised March 2014
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
www.ti.com Develop an Application With the MSP-EXP430G2 LaunchPad
NOTE: The assignment of jumper J3 has been changed in MSP-EXP430G2 revision 1.5, see the
comments in Table 1 to find the assignment for a specific board revision.
Jumpers 4 and 5 connect the UART interface of the emulator to the target device pins P1.1 and P1.2. The
direction of the UART signal lines can be selected by the orientation of the attached jumpers. In horizontal
orientation, the jumpers connect TXD to P1.1 and RXD to P1.2, as they are used for the software UART
communication on the demo application (see Section 3.2). In vertical orientation, the jumpers connect the
TXD signal to P1.2 and the RXD signal to P1.1, as required for the MSP430G2553 USCI.
SLAU318E July 2010 Revised March 2014 MSP-EXP430G2 LaunchPad Evaluation Kit 9
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
Develop an Application With the MSP-EXP430G2 LaunchPad www.ti.com
To program the attached target without interfering with the LaunchPad socket board, jumper connections
TEST and RST of J3 must be open. The interface to the eZ430 target board is always connected to the
MSP-EXP430G2 emulator, so the programming and debugging of a connected LaunchPad target device
is possible only if the eZ430 target is not connected on the same time. The application UART, on the other
hand, is connected directly to the LaunchPad target device, and jumper J3 can be closed to monitor the
transmission from the LaunchPad target to the attached eZ430. This way both possible connections, from
the device to the PC and from the device to the eZ430, can be established without changing the direction
of the UART pins.
The VCC connection to the eZ430 interface is directly connected to the LaunchPad target VCC and can
be separated with jumper J3, if the LaunchPad itself should be powered via a connected battery on J4. To
supply the eZ430 interface with the onboard emulator the jumper J3 VCC needs to be closed.
Table 2 shows the pinout of the eZ430 debugging interface J4, the first pin is the left pin located on the
emulator part of the LaunchPad.
SLAU318E July 2010 Revised March 2014 MSP-EXP430G2 LaunchPad Evaluation Kit 11
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
Develop an Application With the MSP-EXP430G2 LaunchPad www.ti.com
12 MSP-EXP430G2 LaunchPad Evaluation Kit SLAU318E July 2010 Revised March 2014
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
www.ti.com MSP-EXP430G2 Hardware
5 MSP-EXP430G2 Hardware
SLAU318E July 2010 Revised March 2014 MSP-EXP430G2 LaunchPad Evaluation Kit 13
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
www.ti.com
EZ_VBUS
TP6TP4TP2
8 41
9 40
10 39
11 38
12 37 SBW & UART I/F to external Target
GND 13 36
14 35 BRXDI R6 100R
URTS 15 34 BTXDI R7 100R
UDTR 16 33 URXD J4
UDSR UTXD P1.1 1
UCTS EZ_VCC 2
SBWTCK 3
SBWTDIO 4
GND 5
P1.2 6
SL127L6TH
Schematics
1.4
5.2
14
15
MSP-EXP430G2 Hardware
4
2
5
3
1
R22 TUSB3410VF 22p 22p
3k3 S4 SHIELD4
C11
GND
VCC
IO2
IO1
NC
R23 C12
100R 100n GND GND GND USB_MINI_B5
GND 100n
GND GND
SCL
SDA
RST/SBWTDIO P1.3
2
GND
S1
S2
1
1
VCC
100nF
C20
6 P1.4 6 15 P1.7 15
DNP 7 P1.5 7 14 P1.6 14
GND 8 P2.0 8 13 P2.5 13
C14
1nF
1
2
P1.0
LED1 270R
green
R33 J5-2
3
4
P1.6
100nF
LED2 470R
C24
red GND
MSP-EXP430G2 Hardware
GND DNP
MSP-EXP430G2 TARGET SOCKET
GND
1.4
16
17
MSP-EXP430G2 Hardware
EZ_VBUS
TP6TP4TP2
R2 R3
C4 C5 47k 47k
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
4
2
5
3
1
R22 TUSB3410VF 22p 22p
3k3 S4 SHIELD4
C11
GND
VCC
IO2
IO1
NC
R23 C12
100R 100n GND GND GND USB_MINI_B5
GND 100n
GND GND
VSS VCC
CAT24FC32UI
C13 100n
GND GND 1.5
18
19
MSP-EXP430G2 Hardware
2
J6
1
2
3
S1
S2
1
1
GND
GND
6 P1.4 6 15 P1.7 15
DNP 7 P1.5 7 14 P1.6 14
GND 8 P2.0 8 13 P2.5 13
DNP 9 P2.1 9 12 P2.4 12
C22 R28 10 10 11 11
XOUT P2.2 P2.3
12pF 0R Socket: TBD
100nF
J1 Type: TBD J2
C24
C14
1nF
R32 J5-1 DNP
1
2
P1.0
LED1 270R
green
R33 J5-2
3
4
P1.6 GND GND
LED2 470R
red
20 MSP-EXP430G2 LaunchPad Evaluation Kit SLAU318E July 2010 Revised March 2014
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
www.ti.com MSP-EXP430G2 Hardware
SLAU318E July 2010 Revised March 2014 MSP-EXP430G2 LaunchPad Evaluation Kit 21
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
MSP-EXP430G2 Hardware www.ti.com
22 MSP-EXP430G2 LaunchPad Evaluation Kit SLAU318E July 2010 Revised March 2014
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
www.ti.com MSP-EXP430G2 Hardware
SLAU318E July 2010 Revised March 2014 MSP-EXP430G2 LaunchPad Evaluation Kit 23
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
Suggested Reading www.ti.com
6 Suggested Reading
The primary sources of MSP430 information are the device-specific data sheets and the family user's
guides. The most up-to-date versions of those documents can be found at the Texas Instruments MSP430
landing page.
For more information on CCS and IAR, download the latest version from http://www.ti.com/mspds and
read the included user's guides and documentation in the installation folder. Documents describing the
IAR tools (Workbench/C-SPY, the assembler, the C compiler, the linker, and the library) are located in
common\doc and 430\doc. All necessary CCS documents can be found in the msp430\doc folder in the
CCS installation path. The FET user's guide also includes detailed information on how to set up a project
for the MSP430 using IAR or CCS, and it is included in most of the IDE releases and on the TI MSP430
side.
24 MSP-EXP430G2 LaunchPad Evaluation Kit SLAU318E July 2010 Revised March 2014
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
www.ti.com Frequently Asked Questions (FAQ)
SLAU318E July 2010 Revised March 2014 MSP-EXP430G2 LaunchPad Evaluation Kit 25
Submit Documentation Feedback
Copyright 20102014, Texas Instruments Incorporated
Revision History www.ti.com
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Les changements ou les modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de
l'utilisateur pour actionner l'quipement.
Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente
(p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante.
Le prsent metteur radio a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs dans le manuel
dusage et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
Important Notice for Users of EVMs for RF Products in Japan
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministrys Rule for Enforcement of Radio Law of
Japan,
2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
1. 61118328173
2.
3.
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
2. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
3. Since the EVM is not a completed product, it may not meet all applicable regulatory and safety compliance standards (such as UL,
CSA, VDE, CE, RoHS and WEEE) which may normally be associated with similar items. You assume full responsibility to determine
and/or assure compliance with any such standards and related certifications as may be applicable. You will employ reasonable
safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM should fail to
perform as described or expected.
4. You will take care of proper disposal and recycling of the EVMs electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TIs recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright 2014, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as components) are sold subject to TIs terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TIs terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TIs goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or enhanced plastic are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright 2014, Texas Instruments Incorporated