Professional Documents
Culture Documents
Aprilia - Pegaso 650 - '97 - Service Manual PDF
Aprilia - Pegaso 650 - '97 - Service Manual PDF
This manual supplies the main information for normal TABLE OF CONTENTS
servicing procedures.
The information and illustrations contained in this man-
ual are updated to the moment of its publication.
This publication is meant for professional mechanics,
therefore many notions have been intentionally omit-
GENERAL INFORMATION 1
ted, as they were regarded as superfluous.
For any further information, contact aprilia s.p.a.
SERVICE DEPARTMENT.
For any further information see the ENGINE SERVICE
MANUAL, No 933 (D-UK) / No 934 (I-E-F), the EN-
SERVICE AND SETTING UP 2
GINE SPARE PARTS CATALOGUE and the "CHAS-
SIS PARTS" SPARE PARTS CATALOGUE, No 261V
aprilia s.p.a. reserves the right to modify its models at
any time, without prejudice to the main characteristics
here described.
ENGINE 3
All rights as to electronic storage, reproduction and total
or partial adaptation, with any means, are reserved for all
Countries.
The mention to products or services supplied by third par-
ties is made only for information purposes and is not
FUEL SUPPLY SYSTEM 4
binding in any case.
aprilia s.p.a. takes no responsibility as to the perfor-
mance or the use of said products.
COOLING SYSTEM 5
HOW TO USE YOUR SERVICE
AND REPAIR MANUAL
c 8
REPAIR INFORMATION
Remember: 1 mile = 1.6 km
1 km = 0.625 miles
SYMBOLS
Carefully observe the instructions preceded by the fol-
lowing warning signs:
a
Safety norms and regulations to protect the
pilot, the mechanic and other people from se-
vere injuries or grave risks.
In this manual the various versions are indicated by Produced and printed by:
the following symbols: Studio Tecno Public
& optional
Viale del Progresso - 37038 Soave (VR) - Italy
Ph. 045 - 76 11 911
0 -3
NOTE / NOTES / ANMERKUNGEN
0 -4
INFORMAZIONI GENERALI
1
INFORMACIONES GENERALES
GENERAL INFORMATION
2
1 -1
INFORMACIONES GENERALES GENERAL INFORMATION
1 -3
INFORMACIONES GENERALES GENERAL INFORMATION
c c
lo. hicle.
La alteracin de los nmeros de identificacin Do not alter the identification numbers if you
puede provocar graves sanciones penales y do not want to incur severe penal and admin-
administrativas y la invalidez de la garanta. istrative sanctions and to cause the immediate invali-
dation of the guarantee.
1.1.1 NMERO DE BASTIDOR
El nmero del bastidor est impreso en el tubo de la di- 1.1.1 FRAME NUMBER
reccin, en la parte derecha del vehculo. The frame number is printed on the vehicle right side of
the steering tube.
1.1.2 NMERO DE MOTOR
El nmero del motor est impreso en la parte trasera su- 1.1.2 ENGINE NUMBER
perior. The engine number is printed high up on the rear part of
the vehicle.
a a
El combustible para la propulsin de los mo- The fuel used for internal combustion engines
tores de explosin, es muy inflamable y puede is extremely inflammable and in certain con-
volverse explosivo en determinadas condicio- ditions can become explosive.
nes. Es oportuno reponer gasolina y realizar las ope- It is advisable to perform the operations of refuelling
raciones de mantenimiento en una zona ventilada y and maintenance in a well-ventilated area with the en-
con el motor apagado. No fume durante la provisin gine switched off. Do not smoke while refuelling or
de gasolina y cerca de los vapores del combustible; when near fuel vapours and, in any case, avoid con-
evite el contacto con llamas, chispas y cualquier otra tact with naked flames, sparks and any other source
fuente que pueda causar el encendido o la explosin. of heat that might cause the fuel to catch fire or to
Adems, evite que el combustible salga de la boca de explode. Avoid escape of fuel from the fuel filler as it
llenado, ya que ste podra incendiarse si toca las su- could ignite on contact with the red-hot surfaces of
perficies candentes del motor. En caso que se vierta the engine. In case fuel has accidentally been spilt,
accidentalmente combustible, antes de arrancar el make sure that the area is completely dry before
vehculo, controle que la zona est completamente starting the vehicle.
seca. El combustible se dilata con el calor y bajo la Never fill the tank to the brim as fuel expands under
accin de los rayos solares. Por lo tanto, nunca llene the heat of the sun and reacts to the effects of sun ra-
el depsito hasta el tope. Cierre cuidadosamente la diation .
tapa al finalizar las operaciones de reposicin. Close the cap securely after refuelling.
Evite el contacto del combustible con la piel, la inha- Avoid contact of the fuel with the skin and inhalation
lacin de los vapores, la ingestin y el trasiego de un of the fumes; do not swallow fuel or pour it from one
recipiente a otro por medio de un tubo. container into another by means of a tube.
No esparsa el combustible en el medio ambiente. Do not dispose of fuel in the environment.
MANTNGASE LEJOS DEL ALCANCE DE LOS NI- KEEP FUEL AWAY FROM CHILDREN.
OS.
Normal version:
Versin normal: premium grade petrol (4 Stars U) according to the DIN
Gasolina super (4 Stars U) DIN 51 600, mnimo octano 51 600 standard, min. O.N. 98 (N.O.R.M.) and 88
98 (N.O.R.M.) y 88 (N.O.M.M.). (N.O.M.M.).
Versin cataltica 2: Catalytic version 2:
Gasolina super sin plomo segn DIN 51 607, mnimo oc- unleaded petrol according to the DIN 51 607 standard,
tano 95 (N.O.R.M) y 85 (N.O.M.M.). min. O.N. 95 (N.O.R.M.) and 85 (N.O.M.M.).
a a
El aceite del motor puede causar graves da- Engine oil may cause serious damage to the
os a la piel si es manipulado por mucho skin if handled daily and for long periods.
tiempo y diariamente. Se aconseja lavarse las It is advisable to wash your hands thoroughly
manos tras haberlo manipulado. No esparza el aceite after using.
en el medio ambiente. Entrguelo o hgalo retirar por Do not dispose of oil in the environment.
la empresa de recuperacin de aceites usados ms Deliver it to or have it collected by the nearest used
cercana o por el proveedor. oil recovery firm or by the supplier.
Controle cada 500 km el nivel del aceite del motor; vase Check engine oil level every 500 km; see 2.12
2.12 (CONTROL DEL NIVEL DEL ACEITE (CHECKING THE ENGINE OIL LEVEL AND TOPPING
DEL MOTOR Y RELLENO). Cambie el aceite del motor UP).
tras los primeros 1000 km y sucesivamente cada 6000 Change engine oil after the first 1000 km and successive-
km; vase 2.13 (CAMBIO DEL ACEITE MOTOR Y DEL ly every 6000 km; see 2.13 (CHANGING ENGINE OIL
FILTRO DEL ACEITE DEL MOTOR). AND OIL FILTER).
Aceite del motor (aconsejado): Recommended engine oil:
IP SUPERBIKE 4, SAE 5W - 40. IP SUPERBIKE 4, SAE 5W - 40.
Como alternativa a el aceite aconsejado, pueden utilizar- As an alternative to the recommended oil, high quality oils
se aceites de marca con caractersticas conformes o su- with performance conforming or superior to CCMC G-4,
periores a las normas CCMC G-4, A.P.I. SG. A.P.I.SG. specifications may be used.
1 -5
GENERAL INFORMATION
a a
Fork oil may cause serious damage to the The coolant can be harmful if swallowed or if
skin if handled daily and for long periods. it touches the skin or eyes.
It is advisable to wash your hands thoroughly If it comes in contact with the skin or eyes,
after using. rinse thoroughly with large quantities of water.
Do not dispose of oil in the environment. If the coolant is swallowed, induce vomiting and im-
Deliver it to or have it collected by the nearest used mediately consult a doctor.
oil recovery firm or by the supplier.
a
Do not remove the radiator cap when the en-
gine is hot as the coolant is under pressure
Recommended fork oil: IP F.A. 5W or IP F.A. 20W fork
and at a very high temperature.
oil.
If an intermediate performance is desired (between those KEEP COOLANT AWAY FROM CHILDREN.
of IP F.A. 5W and IP F.A. 20W) the products can be mi-
xed as follows:
c
It is advisable to keep the same mixture in the hot season
This vehicle is provided with front and rear as well, since in this way losses due to evaporation are
disc brakes, with separate hydraulic circuits. reduced and it is not necessary to top up so frequently.
The following information refers to a single braking The mineral salt deposits left in the radiator by evapora-
system, but is valid for both. ted water are thus lessened and the efficiency of the coo-
ling system remains unaltered.
a
Brake fluid may cause irritation if it comes
into contact with the skin or eyes. If the outdoor temperature is below 0, check th cooling
Carefully wash the part of the body that has circuit frequently and inf necessary increase the antifree-
come into contact with the fluid. ze concentration (up to maximum 60%).
Consult an oculist or a physician if the fluid comes
into contact with your eyes. Use distilled water for the cooling solution so as not to da-
Do not dispose of brake fluid in the environment. mage the engine.
a
Use the brake fluid; it may chemically alter On the basis of the desired freezing temperature of the
painted surfaces and the parts in plastic, rub- coolant mixture, add to the water the percentage of coo-
ber, etc. lant indicated in the following table:
a
To avoid serious damage to the braking sy- -20 35
stem, do not use fluids other than the recom-
mended ones nor mix different fluids for top- -30 45
ping up.
-40 55
Do not use brake fluid taken from old or already ope-
ned containers. Do not use brake fluid left from pre-
vious repairs if they were done some time ago.
Sudden variations in clearance or an elastic resistan-
ce in the brake levers may be due to trouble in the
c The characteristics of the various antifreeze
liquids are different. Be sure to read the label
on the product to learn the degree of protection it
hydraulic circuits. guarantees.
a
Make sure that the brake discs and the friction pads Use only antifreeze and anticorrosive without
are completely free of grease or oil, especially after nitrite in order to ensure protection at at least
maintenance or checking operations. -35C.
Check that the brake cables are not twisted or worn.
Make sure that neither water nor dust accidentally
enter the circuit.
1 - 10
GENERAL INFORMATION
a
submitted to a more efficacious running-in. The use of naked flames is forbidden for any
type of operation.
a
Before commencing any service or inspection
Only after the first 1500 km of running-in is it operation on the vehicle, switch off the engine and
possible to obtain the best performance. remove the key, wait until the engine and the exhaust
system have cooled down and, if possible, raise the
Keep in mind these important indications: vehicle with the suitable equipment onto firm flat
ground.
Do not open the throttle completely if the speed is low,
In order to avoid burns, be careful not to touch any
both during and after the running-in.
parts of engine or exhaust system which have not
During the first 100 km put on the brakes with caution, cooled down completely.
avoiding sharp and prolonged brakings. This ensures The vehicle is constructed of inedible parts.
a correct bedding-in of the pads on the brake disc. Do not bite, suck, chew or swallow any part of the ve-
Do not open the throttle at low speeds, both during and hicle for any reason whatever.
after running-in. If not expressly described, the reassembly of the
Brake cautiously during the first 100 km, avoiding ab- units is carried out by reversing the order of opera-
rupt and prolonged braking to ensure a correct adap- tions. Do not run the engine in closed or badly venti-
tation of the brake disc pads. lated places.
Do not exceed 4000 rpm during the first 500 km (see Handle fuel with the greatest caution.
table). Never use fuel as a solvent for cleaning the vehicle.
Do not exceed 5000 rpm between the first 500 and
Disconnect the negative cable () from the battery
1000 km (see table).
when electric welding.
a
After the first 1000 km perform the checking
When two or more persons are working together,
operations indicated in the after running-in
make sure that each is working in safe conditions.
column, see 2.1.1 (PERIODIC SERVICE
CHART FOR THE COMPONENTS) in order to avoid Use only original aprilia SPARE PARTS.
injuring yourself or others a/o damaging the vehicle. Use the recommended lubricants.
Use, when necessary, the special tools designed for
Between the first 1000 and 2000 km increase and vary
this vehicle.
your speed, using the maximum acceleration only
Always use the centre stand, if the vehicle is provided
briefly to ensure better coupling of the components
with it.
subject to wear.
In order to carry out certain interventions we recom-
NEVER exceed 5500 rpm (see table).
mend using a stand to hold the vehicle in a vertical po-
After the first 2000 km you may expect better perfor- sition.
mance from the engine without, however, exceeding a When tightening screws and nuts, begin with those ha-
maximum 6250 rpm. ving greater diameters or with inner ones, proceeding
diagonally.
Tighten screws or nuts in successive passages before
Engine maximum rpm applying driving torque.
for the running-in Clean and wash carefully any disassembled parts with
low inflammability detergents.
Mileage km Max. rpm Whenever possible, lubricate the parts before reas-
sembly.
0 - 500 4000 Make sure that each component has been reassem-
500 - 1000 5000 bled correctly.
Always replace gaskets, grommets, circlips, O-rings
1000 - 2000 5500
and split pins with new ones.
over 2000 6250 Before disconnecting the joints (pipes, cables, etc.),
mark the positions on all of them and mark them with
different distinguishing signs.
Each piece must be marked clearly, in order not to
have problems during installation.
The bearings must rotate freely, without halting a/o
noise otherwise they must be replaced.
a
Never re-use a circlip.
When a circlip is disassembled from a shaft it
must be replaced with a new one.
When assembling a new circlip be careful not to
stretch its ends more than strictly necessary to put it
on the shaft.
After installing a circlip, make sure that it is com-
pletely and firmly inserted in its seat.
1 - 11
INFORMAZIONI GENERALI / INFORMACIONES GENERALES / GENERAL INFORMATION
a a a
Limpiego di ricambi NON Utilizar repuestos NO origi- Failure to use aprilia Gen-
originali aprilia pu cau- nales aprilia, puede cau- uine Spare Parts may result
sare problemi di prestazio- sar daos y problemas de in incorrect performance
ni e danneggiamenti. rendimientos. and damages.
1 - 12
INFORMAZIONI GENERALI / INFORMACIONES GENERALES / GENERAL INFORMATION
TRASMISSIONE
RAPPORTI Rapporto Primaria Secondaria Rapporto finale Rapporto totale
DI STRASMISSIONE / 1 37/72 = 1 : 1,946 12/33 = 1 : 2,750 16/47 = 1 : 2,937 15,720
2 16/28 = 1 : 1,750 10,003
3 16/21 = 1 : 1,312 7,502
4 22/33 = 1 : 1,045 5,976
5 24/21 = 1 : 0,875 5,001
TRANSMISION
RELACIONES Relacin del cambio Transmisin primaria Transmisin secundaria Relacin final Relacin total
1 37/72 = 1 : 1,946 12/33 = 1 : 2,750 16/47 = 1 : 2,937 15,720
2 16/28 = 1 : 1,750 10,003
3 16/21 = 1 : 1,312 7,502
4 22/33 = 1 : 1,045 5,976
5 24/21 = 1 : 0,875 5,001
TRANSMISSION
GEAR RATIOS Gear Primary transmission Secondary transmission Final gear ratio Total gear ratio
1 37/72 = 1 : 1,946 12/33 = 1 : 2,750 16/47 = 1 : 2,937 15,720
2 16/28 = 1 : 1,750 10,003
3 16/21 = 1 : 1,312 7,502
4 22/33 = 1 : 1,045 5,976
5 24/21 = 1 : 0,875 5,001
CARBURATORI / CARBURADORES / CARBURETTORS
Modello / Modelo / Model Mikuni BST 33
Diffusore / Difusor / Choke tube 31,5mm
ALIMENTAZIONE / ALIMENTACION / FUEL SUPPLY
Tipo / Tipo / Type a caduta / por gravedad / gravity feed
Carburante / Combustible / Fuel
versione normale / versin normal / normal version benzina super (4 Stars U) DIN 51 600, minimo ottanico 98
(N.O.R.M.) e 88 (N.O.M.M.) / gasolina super (4 Stars U) DIN
51 600, mnimo octanos 98 (N.O.R.M.) y 88 (N.O.M.M.) /
premium grade petrol (4 Stars U) DIN 51 600, O.N. 98
(N.O.R.M.) and 88
versione catalittica / versin cataltica / catalytic version 2 benzina super senza piombo DIN 51 607, minimo ottanico 95
(N.O.R.M.) e 85 (N.O.M.M.) / gasolina super sin plomo segn
DIN 51 607, mnimo octanos 95 (N.O.R.M.) y 85 (N.O.M.M.) /
premium grade unleaded petrol DIN 51 607 min, O.N. 95
(N.O.R.M.) and 85
TELAIO / BASTIDOR / FRAME
Tipo / Tipo / Type A struttura composita in acciaio e lega leggera con culla e reg-
gisella smontabili / Con estructura compuesta de acero y
aleacin ligera con cuna y vstago del silln desmontables /
Composite structure made of steel and light alloy, with remov-
able cradle and saddle pillar.
Angolo inclinazione sterzo / ngulo inclinacin direccin / 28
Steering inclination angle
Avancorsa / Lanzamiento / Fore stroke 109 mm
SOSPENSIONI / SUSPENSIONES / SUSPENSIONS
Anteriore / Delantera / Front forcella telescopica a funzionamento idraulico /
horquilla telescpica con funcionamiento hidrulico /
hydraulically operated telescopic fork
Escursione / Carrera / Stroke 180 mm
Posteriore / Trasera / Rear monoammortizzatore idraulico / amortiguador hidrulico /
hydraulic shock absorber
Escursione / Carrera / Stroke 49 mm
FRENI / FRENOS / BRAKES
Anteriore / Delantero / Front a disco 300 mm con trasmissione idraulica /
de disco 300 mm con transmisin hidrulica /
disc brake, 300 mm with hydraulic transmission
Posteriore / Trasero / Rear a disco 220 mm con trasmissione idraulica /
de disco 220 mm con transmisin hidrulica /
disc brake, 220 mm with hydraulic transmission
RUOTE / RUEDAS / WHEELS
Tipo / Tipo / Type in alluminio a raggi tangenti / de aluminio de radios tangentes /
Aluminium tangent spoke wheels
CERCHI / LLANTAS / RIMS
Anteriore / Delantera / Front 2,15 19"
Posteriore / Trasera / Rear 3,00 17"
PNEUMATICI / NEUMATICOS / TYRES
Anteriore / Delantera / Front 100/90 - 19 57H
Posteriore / Trasera / Rear 130/80 - R17 65H
PRESSIONE DI GONFIAGGIO STANDARD / PRESION DE HINCHADO ESTANDARD / STANDARD INFLATION PRESSURE
Anteriore / Delantera / Front 180 kPa (1,8 bar)
Posteriore / Trasera / Rear 190 kPa (1,9 bar)
PRES. DI GONFIAGGIO CON PASSEGGERO / PRESION DE HINCHADO CON PASAJERO / INFLATION PRES. WITH PASSENGER
Anteriore / Delantera / Front 180 kPa (1,8 bar)
Posteriore / Trasera / Rear 220 kPa (2,2 bar)
1 - 13
INFORMAZIONI GENERALI / INFORMACIONES GENERALES / GENERAL INFORMATION
0 0
0 F.A. 5W e da 0 F.A. 20W, si pos-
Olio forcella (consigliato): olio per forcelle F.A. 5W oppure F.A. 20W.
Qualora si intendesse disporre di un comportamento intermedio tra quelli offerti da
sono miscelare i prodotti come sotto indicato:
SAE 10W 0 F.A. 5W 67% del volume, + 0
F.A. 20W 33% del volume
SAE 15W 0 F.A. 5W 33% del volume, + 0
F.A. 20W 67% del volume
1 - 14
INFORMACIONES GENERALES GENERAL INFORMATION
0 0
as indicated below:
SAE 10W F.A. 5W 67% of the volume, + F.A. 20W 33% of the volume.
SAE 15W 0 F.A. 5W 33% of the volume, + 0 F.A. 20W 67% of the volume.
Bearings and other lubrication points (recommended): 0
AUTOGREASE MP.
As an alternative to the recommended product, use high-quality grease for rolling bearings, working temperature range
-30C+140C, dripping point 150C230C, high protection against corrosion, good resistance to water and oxidation.
Protection of the battery poles: neutral grease or Vaseline.
Spray grease for chains (recommended): 0 CHAIN SPRAY.
Brake fluid (recommended): 0 F.F., DOT 5 (compatible with DOT 4).
a Use new brake fluid only.
0 0
as indicated below:
0 0
SAE 10W F.A. 5W 67% of the volume, + F.A. 20W 33% of the volume.
SAE 15W F.A. 5W 33% of the volume, + F.A. 20W 67% of the volume.
1 - 15
INFORMAZIONI GENERALI
1 - 16
1
OPERAZIONI DI MANUTENZIONE
PERIODICA E DI MESSA A PUNTO 2
OPERACIONES DE MANTENIMIENTO
PERIDICO Y DE PUESTA A PUNTO
3
PERIODIC SERVICE
AND SETTING UP OPERATIONS
4
2 -1
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
2.1 PLAN PARA EL MANTENIMIENTO 2.1 PERIODIC SERVICE PLAN ...................... Pag. 2-4
PERIDICO ......................................................Pag. 2-4 2.1.1 PERIODIC SERVICE CHART
2.1.1 FICHA DE MANTENIMIENTO PERIDICO ....Pag. 2-5 FOR THE COMPONENTS .............................. Pag. 2-5
2.2 PUNTOS POR LUBRICAR.........................Pag. 2-6 2.2 POINTS TO LUBRICATE .......................... Pag. 2-6
2.3 BATERA ...........................................................Pag. 2-9
2.3.1 CONTROL DEL NIVEL DEL ELECTROLITO .Pag. 2-9
2.3.2 RECARGA BATERIA ....................................Pag. 2-11
2.3 BATTERY ......................................................... Pag. 2-9
2.3.1 CHECKING THE ELECTROLYTE LEVEL ..... Pag. 2-9
2.3.2 RECHARGING THE BATTERY .................... Pag. 2-11
2
2.3.3 LARGA INACTIVIDAD ..................................Pag. 2-11 2.3.3 LONG INACTIVITY OF THE BATTERY ....... Pag. 2-11
2.4 TUERCAS DE LOS TUBOS 2.4 EXHAUST MANIFOLD NUTS................ Pag. 2-11
DE ESCAPE ..................................................Pag. 2-11 2.5 AIR CLEANER .............................................. Pag. 2-13
2.5 FILTRO DEL AIRE ......................................Pag. 2-13 2.6 SPARK PLUG ............................................... Pag. 2-15
2.6 BUJA ...............................................................Pag. 2-15 2.7 CARBURETTORS ....................................... Pag. 2-17
2.7 CARBURADORES .......................................Pag. 2-17 2.8 FUEL TUBING.............................................. Pag. 2-17
2.8 TUBERAS DEL COMBUSTIBLE .........Pag. 2-17
2.9 ACCELERATOR CABLE .......................... Pag. 2-17
2.9 CABLE DEL ACELERADOR ....................Pag. 2-17 2.9.1 ADJUSTING
2.9.1 AJUSTE MANDO ACCELERADOR ..............Pag. 2-17 THE ACCELERATOR CONTROL ................ Pag. 2-17
2.9.2 AJUSTE DEL RGIMEN DEL RALENT ......Pag. 2-17 2.9.2 ADJUSTMENT OF IDLING RPM .................. Pag. 2-17
2.10 CABLE DEL ARRANQUE EN FRO ..Pag. 2-19 2.10 COLD START CABLE............................. Pag. 2-19
2.11 CABLE DEL EMBRAGUE ......................Pag. 2-19 2.11 CLUTCH CABLE ....................................... Pag. 2-19
2.12 CONTROL DEL NIVEL DEL ACEITE 2.12 CHECKING THE ENGINE OIL LEVEL
DEL MOTOR Y RELLENO.....................Pag. 2-21 AND TOPPING UP................................... Pag. 2-21
2.13 CAMBIO DEL ACEITE MOTOR Y DEL
FILTRO DEL ACEITE DEL MOTOR ..Pag. 2-23 2.13 CHANGING ENGINE OIL
2.13.1 PURGA DEL AIRE DE LA BOMBA
AND OIL FILTER ...................................... Pag. 2-23
DE ALIMENTACIN DEL ACEITE ..............Pag. 2-25 2.13.1 AIR BLEEDING
FROM OIL DELIVERY PUMP ...................... Pag. 2-25
2.14 CONTROL Y RELLENO
DEL LQUIDO REFRIGERANTE ...........Pag. 2-27 2.14 CHECKING
AND TOPPING UP COOLANT ........... Pag. 2-27
2.15 SUBSTITUCIN DEL LQUIDO
REFRIGERANTE .......................................Pag. 2-29 2.15 CHANGING THE COOLANT ............... Pag. 2-29
2.16 CADENA DE TRANSMISIN...............Pag. 2-31 2.16 DRIVING CHAIN ...................................... Pag. 2-31
2.16.1 CONTROL DEL JUEGO ..............................Pag. 2-31 2.16.1 CLEARANCE CONTROL ........................... Pag. 2-31
2.16.2 CONTROL DEL DESGASTE .......................Pag. 2-33 2.16.2 CHECKING WEAR...................................... Pag. 2-33
2.16.3 AJUSTE .......................................................Pag. 2-33 2.16.3 ADJUSTMENT ............................................ Pag. 2-33
2.16.4 LIMPIEZA Y LUBRICACIN .......................Pag. 2-33 2.16.4 CLEANING AND LUBRICATION ............... Pag. 2-33
2.17 CONTROL Y RELLENO LIQUIDO 2.17 CHECKING AND TOPPING UP
FRENO DELANTERO ..............................Pag. 2-35 THE FRONT BRAKE FLUID ................ Pag. 2-35
2.18 CONTROL Y RELLENO 2.18 CHECKING AND TOPPING UP
LIQUIDO FRENO TRASERO ...............Pag. 2-37 THE REAR BRAKE FLUID ................... Pag. 2-37
2.19 PURGA DEL AIRE 2.19 BLEEDING
DEL SISTEMA DE FRENADO .............Pag. 2-39 THE BRAKING SYSTEM ...................... Pag. 2-39
2.20 AJUSTE DEL PEDAL 2.20 REAR BRAKE PEDAL
DEL FRENO TRASERO ..........................Pag. 2-41 ADJUSTMENT .......................................... Pag. 2-41
2.21 AJUSTE DE LA PALANCA 2.21 FRONT BRAKE LEVER
DEL FRENO DELANTERO ..................Pag. 2-41 ADJUSTMENT .......................................... Pag. 2-41
2.22 COMPROBACION 2.22 CHECKING
DESGASTE PASTILLAS ........................Pag. 2-41 THE BRAKE PAD WEAR ...................... Pag. 2-41
2.23 NEUMTICOS ............................................Pag. 2-43 2.23 TYRES ........................................................... Pag. 2-43
2.23.1 CONDICIONES DE LA BANDA 2.23.1 CONDITION OF TREAD ............................. Pag. 2-43
DE RODAMIENTO .......................................Pag. 2-43 2.23.2 INFLATION PRESSURE ............................. Pag. 2-43
2.23.2 PRESIN DE INFLADO ..............................Pag. 2-43 2.24 STEERING................................................... Pag. 2-45
2.24 DIRECCIN .................................................Pag. 2-45 2.24.1 CHECKING THE BEARING SLACKS ........ Pag. 2-45
2.24.1 CONTROL JUEGO COJINETES .................Pag. 2-45 2.24.2 ADJUSTING THE BEARING SLACKS ...... Pag. 2-45
2.24.2 AJUSTE JUEGO COJINETES ....................Pag. 2-45 2.25 FRONT FORK ............................................ Pag. 2-47
2.25 HORQUILLA DELANTERA ...................Pag. 2-47 2.26 REAR FORK ............................................... Pag. 2-47
2.26 HORQUILLA TRASERA .........................Pag. 2-47 2.26.1 ADJUSTING THE REAR FORK ................. Pag. 2-47
2.26.1 AJUSTE BASCULANTE .............................Pag. 2-47
2.27 REAR SUSPENSION .............................. Pag. 2-49
2.27 SUSPENSIN TRASERA ......................Pag. 2-49 2.27.1 ADJUSTING THE REAR SUSPENSION .... Pag. 2-49
2.27.1 AJUSTE SUSPENSION TRASERA ............Pag. 2-49 2.27.2 ADJUSTING
2.27.2 AJUSTE SUSPENSION TRASERA THE REAR SUSPENSIONWITH PRELOAD
CON REGULACION HIDRAULICA
DE PRECARGA &
....................................Pag. 2-51
HYDRAULIC ADJUSTMENT &
............... Pag. 2-51
2.27.3 CHECKING
2.27.3 CONTROL PALANCAS THE REAR SUSPENSION LINKAGE ........ Pag. 2-51
SUSPENSION TRASERA ............................Pag. 2-51
2.28 FRONT WHEEL ......................................... Pag. 2-53
2.28 RUEDA DELANTERA ..............................Pag. 2-53
2.29 REAR WHEEL ............................................ Pag. 2-53
2.29 RUEDA TRASERA ....................................Pag. 2-53
2.30 APRIETE DE LOS TORNILLOS 2.30 TIGHTENING SCREWS
Y TUERCAS ................................................Pag. 2-54 AND NUTS .................................................. Pag. 2-54
2 -3
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO / OPERACIONES DE MANTENIMIENTO PERIDICO
Y DE PUESTA A PUNTO / PERIODIC SERVICE AND SETTING UP OPERATIONS
Questa sezione descrive le procedu- Esta seccin describe los procedi- This section describes the proce-
re dintervento per la manutenzione mientos de mantenimiento peridico dures for periodic service on the prin-
periodica dei principali componenti de los principales componentes del cipal components of the vehicle.
del veicolo. vehculo.
a
Before beginning any serv-
a a
Prima di iniziare qualsiasi Antes de comenzar con ice operations or inspec-
intervento di manutenzione cualquier tipo de manteni- tion of the vehicle, switch
o ispezione al veicolo, ar- miento o inspeccin del ve- off the engine and remove the key,
restare il motore e togliere la chia- hculo, apague el motor y quite la wait until the engine and the ex-
ve, attendere che motore e impian- llave, espere a que el motor y el haust system have cooled down
to di scarico si siano raffreddati, sistema de escape se hayan en- and, if possible, lift the vehicles
sollevare possibilmente il veicolo friado y levante el vehculo con un with the proper equipment onto
con apposita attrezzatura, su di un equipo adecuado, sobre una su- firm and flat ground.
terreno solido e in piano. perficie slida y plana. In order to avoid burns, be careful
Porre particolare attenzione alle Para evitar quemaduras, tenga not to touch any parts of the en-
parti ancora calde del motore e cuidado con las piezas del motor y gine or exhaust system which
dellimpianto di scarico, in modo del sistema de escape que an es- have not cooled down completely.
tale da evitare ustioni. tn caliente. The vehicle is constructed of non-
Il veicolo e costruito con parti non El vehculo est fabricado con pie- edible parts.
commestibili. Non mordere, suc- zas no comestibles. Do not bite, suck, chew or low any
chiare, masticare o ingerire nessu- No muerda, chupe, mastique ni part of the vehicle for any reason
na parte dello stesso per nessun trague ninguna pieza del mismo whatever.
c
motivo. por ningn motivo.
c c
If not expressly described
Se non espressamente de- Si no est expresamente otherwise, reassembly of
scritto, il rimontaggio dei indicado, la reinstalacin the units is carried out repeating
gruppi segue in senso inverso le de los grupos sigue el orden con- the disassembly operations in the
operazioni di smontaggio. trario a las operaciones de des- reverse order.
c
montaje.
Remember:
1 mile = 1.6 km
1 km = 0.625 miles
2.1 PIANO PER LA 2.1 PLAN PARA EL 2.1 PERIODIC SERVICE PLAN
MANUTENZIONE MANTENIMIENTO
aprilia recommends respecting the
PERIODICA PERIDICO
intervals indicated for the periodic
Per mantenere ottimali le condizioni Para que las condiciones de funcio- service on the various components in
di funzionamento del veicolo, aprilia namiento del vehculo se mantengan order to ensure the best operating
raccomanda di rispettare gli intervalli ptimas, aprilia aconseja respetar conditions of the vehicle.
previsti per gli interventi di manuten- los intervalos previstos para las inter-
zione periodica dei vari componenti. venciones de mantenimiento peridi-
co de los diferentes componentes.
2 -4
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO / OPERACIONES DE MANTENIMIENTO PERIDICO
Y DE PUESTA A PUNTO / PERIODIC SERVICE AND SETTING UP OPERATIONS
2.1.1 SCHEDA DI MANUTENZIONE 2.1.1 FICHA DE MANTENIMIENTO 2.1.1 PERIODIC SERVICE CHART
PERIODICA PERIDICO FOR THE COMPONENTS
2 -5
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO / OPERACIONES DE MANTENIMIENTO PERIDICO
Y DE PUESTA A PUNTO / PERIODIC SERVICE AND SETTING UP OPERATIONS
2.2 PUNTI DA LUBRIFICARE 2.2 PUNTOS POR LUBRICAR 2.2 POINTS TO LUBRICATE
Una lubrificazione corretta impor- Una lubricacin correcta es importan- Correct lubrication is important for a
tante per un funzionamento scorre- te para que las piezas no se agarro- good performance and long life of the
vole e una lunga durata del veicolo. ten y garantizar una larga duracin vehicle.
del vehculo.
2 -6
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO / OPERACIONES DE MANTENIMIENTO PERIDICO
Y DE PUESTA A PUNTO / PERIODIC SERVICE AND SETTING UP OPERATIONS
2 3
1 7 12 6 5
14 13 12 11 10
2 -7
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
2.3 BATTERIA
Leggere attentamente 1.4 (PRECAUZIONI E INFOR-
MAZIONI GENERALI).
Dopo i primi 1000 km (o 4 mesi) e successivamente ogni
6000 km (o 8 mesi) controllare il livello dellelettrolita e il
serraggio dei morsetti.
a
L'elettrolita della batteria tossico, caustico,
e a contatto con l'epidermide pu causare
ustioni, in quanto contiene acido solforico.
Indossare abiti protettivi, una maschera per il viso
e/o occhiali nel caso di manutenzione.
a
Se del liquido elettrolitico venisse a contatto
con la pelle, lavare con abbondante acqua cor-
rente. Se venisse a contatto con gli occhi, lava-
re con acqua abbondante per quindici minuti, quindi ri-
volgersi tempestivamente a un oculista. Se venisse
ingerito accidentalmente, bere grosse quantit di ac-
qua o latte, continuare con latte di magnesia od olio ve-
getale, quindi rivolgersi prontamente a un medico.
La batteria emana gas esplosivi (specialmente durante
la fase di attivazione e/o ricarica), opportuno tenere
lontane fiamme, scintille, sigarette e qualsiasi altra fon-
te di calore. Durante la ricarica o l'uso, provvedere a
un'adeguata ventilazione del locale, evitare l'inalazione
dei gas emessi durante la ricarica della stessa.
Non invertire mai il collegamento dei cavi della batte-
ria.
Porre attenzione a non inclinare troppo il veicolo onde
evitare pericolose fuoriuscite del liquido della batteria.
a
Il liquido della batteria corrosivo.
Non versarlo o spargerlo, in particolare sulle
parti in plastica.
a
Collegare e scollegare la batteria con linter-
ruttore di accensione in posizione m.
Collegare prima il prima il cavo positivo (+) e
poi quello negativo ().
Scollegare seguendo lordine inverso.
2 -8
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
a a
El electrolito de la batera es txico, custico The electrolyte in the battery is toxic and
y si toca la piel puede causar quemaduras ya caustic and may cause burns on contact with
que contiene cido sulfrico. En el caso de the skin as it contains sulphuric acid. Wear
mantenimiento, colquese ropa de proteccin, una protective clothing, a face mask and/or goggles dur-
mscara para la cara y/o gafas. ing service operations.
a a
Si el lquido electroltico tocara la piel, lvese If electrolyte liquid comes in contact with the
abundantemente con agua corriente. Si entra en skin, wash with large quantities of running
contacto con los ojos, lave abundamente con water. In case of contact with the eyes, wash
agua por quince minutos y luego dirjase inmediata- with large quantities of water for fifteen minutes and
mente a un oculista. Si se traga accidentalmente, beba consult an oculist without delay.
mucha agua o leche, siga con leche de magnesia o If the liquid is accidentally swallowed, drink large
aceite vegetal, luego dirjase inmediatamente a un m- amounts of water or milk, then continue drinking milk
dico. La batera emana gases explosivos (especialmen- of magnesia or vegetable oil and promptly call a doc-
te durante la fase de activacin y/o recarga), es conve- tor. The battery gives off explosive gases, particular-
niente mantener alejadas llamas, chispas, cigarrillos y ly during the phase of starting and/or recharging;
cualquier otra fuente de calor. keep it away from flames, sparks, cigarettes and any
Durante la recarga o el uso, ventile adecuadamente el other source of heat.
local, evite inhalar los gases que emite durante la recar- During recharging or using, make sure the room is
ga de la misma. Nunca invierta las conexiones de los properly ventilated and avoid inhaling the gases re-
cables de la batera. Tenga cuidado en no inclinar de- leased during recharging. Never invert the connec-
masiado el vehculo para evitar que el riesgo de que el tion of the battery cables.
lquido salga de la batera.
a a
El lquido de la batera es corrosivo. The battery fluid which is very corrosive.
No lo vierta o desparrame, en particular, sobre Do not pour or spill it, especially on the plastic
las piezas de plstico. parts.
MANTNGASE ALEJADO DEL ALCANCE DE LOS NI- KEEP AWAY FROM CHILDREN.
OS.
a
Connect and disconnect the battery with the
a
Conecte y desconecte la batera con el inter- ignition switch in position m.
ruptor de encendido en posicin m. Connect first the positive cable (+) and then
Conecte antes el cable positivo (+) y luego el the negative cable ().
negativo (). Disconnect following the reverse order.
Desconecte siguiendo el orden contrario.
2.3.1 CONTROL DEL NIVEL DEL ELECTROLITO 2.3.1 CHECKING THE ELECTROLYTE LEVEL
Para controlar el nivel del electrolito es necesario: To check the electrolyte level:
Quitar el panel izquierdo, vase 7.1.4 (DESMONTA- Remove the left side, see 7.1.4 (REMOVING THE
JE PANELES LATERALES DERECHO E IZQUIER- RIGHT AND LEFT SIDES).
DO). Unscrew and remove the screw (1).
Destornillar y quitar el tornillo (1). Remove the battery cover (2).
Quitar la tapa batera (2). Make sure that the fluid level is included between the
Controlar que el nivel del lquido est comprendido en- two "MIN" and "MAX" notches stamped on the battery
tre las dos muescas "MIN" y "MAX" , impresas so- side.
bre el lado de la batera.
Otherwise:
Eventualmente: Remove the element plugs.
Quite los tapones de los elementos.
Restaure el nivel del lquido aadiendo slo agua des- Top up by adding distilled water only.
tilada.
c
Check battery voltage with a portable tester.
Controle con un tester porttil, la tensin de la If voltage is less than 12V, the battery must be
batera. Si la tensin es inferior a 12V, hay que recharged.
recargar la batera.
2 -9
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
2.3.2 RICARICA
Effettuare il controllo livello elettrolita, ripristinandolo se
necessario, quindi:
Assicurarsi che linterruttore di accensione sia in posi-
zione m.
Scollegare nellordine il cavo negativo () e quello po-
sitivo (+).
a
Nel rimontaggio collegare sempre il tubetto
sfiato batteria, per evitare che i vapori di acido
solforico, uscendo dallo sfiato, possano cor-
rodere limpianto elettrico, le parti verniciate, i parti-
colari in gomma o le guarnizioni.
2 - 10
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
a a
Durante la instalacin, conecte siempre el Upon reassembly, always connect the battery
tubo respiradero de la batera para evitar que breather pipe, to prevent the sulphuric acid
los vapores del cido sulfrico, al salir del res- vapours from corroding the electric system,
piradero, puedan corroer la instalacin elctrica, las painted parts, rubber elements or gaskets when they
partes barnizadas, las piezas de goma o las juntas. exit the breather pipe itself.
Saque la batera de su alojamiento y colquela en un Extract the battery from its container and put it in a cool
lugar fresco y seco. and dry place.
Quite los tapones de los elementos. Remove the element plugs.
Conecte la batera a un carga-bateras. Connect the battery with a battery charger.
Se aconseja una recarga utilizando un amperaje de A recharge with an amperage equal to 1/10th of the
1/10 de la capacidad de la misma batera. battery capacity is recommended.
Tras haber realizado la recarga, vuelva a controlar el After the recharging operation, check the electrolyte
nivel del electrolito y de resultar necesario rellene con level again and if necessary top up with distilled water.
agua destilada.
Durante el invierno o cuando el vehculo queda parado, During the winter months or whenever the vehicle is not
es importante controlar la carga (una vez al mes aproxi- in use, it is important to check the charge (about once a
madamente) para evitar que se degrade. month) in order to prevent deterioration of the battery.
Para el mantenimiento de la batera refirase al cap- For maintenance of the battery refer to chapter
tulo 6.11.2 (MANTENIMIENTO). 6.11.2 (MAINTENANCE).
Apriete tras los primeros 1000 km ( 4 meses) y sucesi- Tighten nuts after the first 1000 km (or 4 months) and
vamente, cada 6000 km (o 8 meses). then after every 6000 km (or 8 months).
Desmonte el carenado delantero, vase 7.1.14 Remove the front fairing, see 7.1.14 (REMOVING
(DESMONTAJE CARENADO DELANTERO). THE FRONT FAIRING).
Apriete las tuercas del tubo de escape (vase figu- Tighten the exhaust manifold nuts (see figure) to the
ra) con el par indicado. prescribed torque.
2 - 11
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
La pulizia parziale del filtro aria non esclude o
posticipa la sostituzione del filtro stesso.
Non avviare il motore con il filtro aria rimosso.
Non utilizzare benzina o solventi per la pulizia
dellelemento filtrante; potrebbero causare un incen-
dio al sistema di alimentazione, con grave pericolo
per le persone e il veicolo.
RIMOZIONE
Rimuovere la sella, vedi 7.1.3 (RIMOZIONE SELLA).
Ruotare in senso orario il convogliatore aria (1) solle-
varlo e rimuoverlo.
Estrarre il filtro aria (2).
Pulizia parziale
a
Non premere o battere sulla rete metallica del
filtro aria. Non agire con cacciaviti o altro sul
filtro stesso.
Afferrare il filtro aria verticalmente e batterlo pi volte
sopra un piano pulito.
Alloccorrenza, pulire il filtro aria con un getto daria
compressa (dirigendolo dallinterno verso lesterno del
filtro).
Pulire esternamente il filtro aria con un panno.
Sostituzione
Sostituire il filtro aria con uno nuovo dello stesso tipo.
Controllare lintegrit della guarnizione (3); se danneg-
giata sostituirla.
Ogni 6000 km, rimuovere il tappino (4) e lasciar fuoriu-
scire eventuali impurit depositate allinterno della
cassa filtro.
a
Durante le operazioni di pulizia dellelemento
filtrante, verificare che non vi siano lacerazio-
ni. In caso contrario sostituire lelemento fil-
trante.
Assicurarsi che lelemento filtrante sia correttamente
posizionato, in modo da non far passare aria non fil-
trata.
Non dimenticare che lusura precoce dei segmenti
del pistone e del cilindro spesso causata dallele-
mento filtrante difettoso o mal posizionato.
2 - 12
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con mucha atencin 1.4 (PRECAUCIONES E IN- Read 1.4 carefully (PRECAUTIONS AND GENERAL
FORMACIONES GENERALES). INFORMATION).
Limpie cada 6000 km. Substituya cada 12000 km. Clean every 6000 km. Replace every 12000 km.
a a
La limpieza parcial del filtro no excluye ni The partial cleaning of the filter does not ex-
aplaza la sustitucin del filtro mismo. clude or postpone the replacement of the filter
No ponga en marcha el motor si se ha des- itself. Do not start the engine if the air cleaner
montado el filtro de aire. No utilice gasolina o disol- has been removed.
ventes para limpiar el elemento filtrante; esto podra Do not use petrol or solvents to clean the filtering el-
causar un incendio en el sistema de alimentacin ement; they may cause a fire in the fuel system, with
con grave peligro para las personas y para el vehcu- serious risks for people and for the vehicle itself.
lo.
REMOVAL
DESMONTAJE
Remove the saddle, see 7.1.3 (REMOVING THE
Desmonte el silln, vase 7.1.3 (DESMONTAJE SI- SADDLE).
LLIN). Rotate the air conveyor (1) clockwise, raise and re-
Gire en sentido horario el encuazador de aire (1), le- move it.
vntela y extrigala. Extract the air cleaner (2).
Extraiga el filtro del aire (2).
Partial cleaning
Limpieza parcial
a
Do not press or strike the metal net of the air
a
No presione ni golpee sobre la red metlica del cleaner.
filtro del aire. No acte con un destornillador o Do not use screwdrivers or alike.
con otra herramienta sobre el filtro mismo.
Seize the air cleaner vertically and strike it more than
Sujete el filtro del aire verticalmente y golpelo varias once on a clean surface.
veces sobre una superficie limpia. If necessary, clean the filter with a compressed air jet
Si es necesario limpie el filtro del aire con un chorro de (directing it from the inside towards the outside of the
aire comprimido (dirigindolo desde el interior hacia el filter).
exterior del filtro). Clean the outer part of the air cleaner with a cloth.
Limpie la parte exterior del filtro con un pao.
Changing
Sustitucin
Replace the air cleaner with a new one of the same
Sustituya el filtro del aire con otro nuevo del mismo ti- type.
po. Make sure that the gasket (3) is intact; if it is damaged,
Controle la integridad de la junta (3); de resultar daa- change it.
da sustityala. Every 6000 km, remove the plug (4), so that any impu-
Cada 6000 km quite el taponcito (4) y deje salir even- rity that may have accumulated inside the filter case
tuales impurezas que se hayan depositado dentro de can be discharged.
la caja del filtro.
a
During above cleaning operations, check to
a
Durante la limpieza del filtro, controle que no see that there are no tears or rips in the filter-
est desgarrado. ing element. Otherwise replace it.
En caso contrario, substituya el filtro. Make sure that the filtering element is correctly posi-
Cercirese que el filtro est colocado correctamente, tioned so as not to allow passage of non-filtered air.
de manera que no pase aire sin filtrar. Remember that premature wear and tear on the seg-
No se olvide que el desgaste precoz de los segmen- ments of the piston or the cylinder is often caused by
tos del pistn y del cilindro, es generalmente causa- a defective and badly positioned filtering element.
do por el elemento filtrante defectuoso o mal coloca-
do. If the vehicle is used in dusty areas, clean the filtering
element more frequently.
Si se utiliza el vehculo en zonas polvorientas, limpie Using the vehicle without the filtering element, or
el filtro ms seguido. with the element damaged, considerably increases
Utilizar el vehculo sin el filtro o con el filtro daado, wear and tear on the engine.
aumenta considerablemente el desgaste del motor. Make sure the filtering element is always in perfect
Cercirese que el filtro est siempre en perfectas condition. the life of the engine depends, for the most
condiciones. la duracin del motor depende en gran part, on this component.
medida de este componente.
2 - 13
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
2.6 CANDELA
a
Non disinserire mai la pipetta della candela
con il motore avviato, potreste ricevere una
potente scarica elettrica dal sistema di accen-
sione.
Disinserire la pipetta della candela (1).
Togliere ogni traccia di sporco dalla base della candela.
Svitare la candela (chiave in dotazione al kit attrezzi)
ed estrarla dalla sede, avendo cura di non far entrare
polvere o altre sostanze all'interno del cilindro.
Controllare che sull'elettrodo e sulla porcellana centra-
le della candela non ci siano depositi carboniosi o se-
gni di corrosione, eventualmente pulire con un apposi-
to pulitore per candele, con un filo di ferro e/o
spazzolino metallico.
Soffiare energicamente con un getto d'aria per evitare
che i residui rimossi entrino nel motore.
Se la candela presenta screpolature sull'isolante, elet-
trodi corrosi o eccessivi depositi, deve essere sostitui-
ta.
Controllare la distanza tra gli elettrodi con un calibro
per spessori. Questa deve essere di 0,6 0,7 mm (ve-
dere figura), eventualmente regolarla, piegando con
cautela l'elettrodo di massa.
Accertarsi che la rondella sia in buone condizioni.
Con la rondella montata, avvitare a mano fino in fondo
la candela per evitare di danneggiare la filettatura.
Con lapposita chiave, serrare facendo compiere 1/2
giro alla candela per comprimere la rondella.
Coppia di serraggio candela: 20 Nm (2 kgm).
Rimontare correttamente la pipetta della candela.
a
La candela deve essere ben avvitata, altrimen-
ti il motore si potrebbe surriscaldare, danneg-
giandosi gravemente. Utilizzare solo candele
del tipo consigliato, altrimenti si possono compro-
mettere le prestazioni e la durata del motore.
In caso di sostituzione della candela si raccomanda lim-
piego delle candele standard; vedi 1.6 (CARATTERI-
STICHE TECNICHE).
Smontare la candela e controllare lisolante.
La gradazione termica corretta se entrambi gli isolanti
sono di colore marrone chiaro.
Se gli isolanti risultano anneriti dai depositi carboniosi,
utilizzare candele con grado termico inferiore.
Se lisolante si presenta bianco, sostituire la candela con
altra di grado termico inferiore.
Le candele con elevato grado termico sono usate per
marcia ad alta velocit. Sono concepite per avere un suf-
ficiente raffreddamento e prevenire il surriscaldamento e
sono chiamate candele di tipo freddo.
a
Quando si sostituisce la candela, controllare il
passo e la lunghezza della filettatura. Se la
parte filettata troppo corta, i depositi carbo-
niosi si depositeranno sulla sede della filettatura ri-
schiando cos di danneggiare il motore quando si ri-
monta quella corretta.
2 - 14
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con mucha atencin 1.4 (PRECAUCIONES E IN- Read 1.4 carefully (PRECAUTIONS AND GENERAL
FORMACIONES GENERALES). INFORMATION).
Controle cada 6000 km y substituya cada 12000 km. Check every 6000 km and replace every 12000 km.
a a
No desconecte nunca la pipeta de la buja con Never disconnect the spark plug cap with the
el motor en marcha, porque podra recibir una engine running, since you may get an electric
fuerte descarga elctrica del sistema de en- shock from the ignition system.
cendido.
Take off the spark plug cap (1).
Quite la pipa de la buja (1). Remove every trace of dirt from the base of the spark
Limpie muy bien la base de la buja. plug.
Desenrsque la buja (con la llave suministrada con el Unscrew the spark plug (spanner to be found in tool
set de herramientas) y extrigala del alojamiento, te- kit) and extract it from its seat, taking care that no dust
niendo cuidado de que no entre polvo u otras substan- or other substances enter the cylinder.
cias en el interior del cilindro. Make sure there are no carbon deposits or corrosion
Controle que sobre el electrodo y sobre la porcelana marks on the electrode or the central porcelain part.
central de la buja no haya costras de carbonilla o sig- If necessary, clean them with the special spark plug
nos de corrosin. Eventualmente, limpie con un lim- cleaner, with an iron wire and/or metal brush.
piador adecuado para bujas, con un alambre y/o con Blow a jet of air into the spark plug to prevent any re-
un cepillo metlico. Sople muy fuerte con un chorro de sidual material from entering the engine.
aire comprimido para evitar que los residuos que se The spark plug must be replaced if it shows cracks on
han quitado puedan entrar en el motor. the insulating material, corroded electrodes or exces-
Substituya la buja si tiene hendiduras en el aislador, sive deposits.
electrodos oxidados o incrustaciones excesivas. Check the spark plug gap with a thickness gauge; it
Controle la distancia entre los electrodos por medio de should be 0.6 0.7 mm (see figure). Adjust it, if nec-
un calibre de espesor. Esta debe ser de 0,6 0,7 mm essary, carefully bending the earth electrode.
(vase figura); eventualmente ajstela curvando con Make sure the washer is in good condition.
cuidado el electrodo de masa. With the washer in place, screw the spark plug com-
Cercirese que la arandela est en buenas condicio- pletely by hand so as not to damage the thread.
nes. Con la arandela montada, enrosque la buja con la Tighten the spark plug with the special spanner, giving
mano hasta el fondo para evitar que se dae la rosca. it half a turn to compress the washer.
Apriete con la llave, hacindole dar 1/2 vuelta a la Spark plug driving torque: 20 Nm (2 kgm).
buja para comprimir la arandela.
Put back the spark plug cap.
Par de apriete buja: 20 Nm (2 kgm).
a
Monte nuevamente la pipa de la buja. The spark plug must be tightened well other-
wise the engine could overheat and be seri-
a
La buja debe estar bien apretada, de otro
ously damaged. Use the recommended type
modo el motor podra sobrecalentarse dan-
of spark plug only so as not to endanger the perform-
dose gravemente. Utilice slo bujas del tipo
ance and life of the engine.
aconsejado, para no comprometer el rendimiento y la
duracin del motor.
When changing the spark plug we recommend using the
Si debe substituir la buja, aconsejamos utilizar las bujas standard type, see 1.6 (TECHNICAL SPECIFICATIONS).
estndar, vase 1.6 (FICHA TECNICA). Remove the spark plug and check the insulator.
Desmonte la buja y controle el aislante. The heat rating is correct if both the insulators are col-
La graduacin trmica es correcta, si ambos aislantes oured light brown. If the insulators are seen to be black-
son de color marrn claro. Si los aislantes estn ennegre- ened from carbon deposits, use spark plugs with a hotter
cidos por las incrustaciones de carbonilla, utilice bujas heat rating.
con un grado trmico inferior.
If the insulator is white, replace the spark plug with one
Si el aislante est blanco, substituya la buja por otra con
with a colder heat rating.
un grado trmico inferior.
Spark plugs with a cold heat rating are used for high
Las bujas con un alto grado trmico se utilizan para mar-
speed driving.
chas a altas velocidades. Estn fabricadas para que se
They are designed to cool sufficiently and to prevent
enfren rpidamente y prevenir el sobrecalentamiento, y
overheating and are called cold spark plugs.
son llamadas bujas de tipo fro.
a a
Cuando substituya la buja, controle el paso y When replacing a spark plug, check the pitch
la longitud de la rosca. Si la parte roscada es and length of the thread. If the threaded part is
demasiado corta, las incrustaciones de carbo- too short, carbon deposits will settle on the
nilla se depositarn en el alojamiento de la rosca, con thread seat and may result in damage to the engine
el riesgo de daar el motor quando se reinstale la co- when the correct one is positioned back in place.
rrecta.
2 - 15
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
2.7 CARBURATORI
Controllare dopo i primi 1000 km (o 4 mesi) e successiva-
mente ogni 6000 km (o 8 mesi).
a
Dopo aver completato la regolazione, verifica-
re che la rotazione del manubrio non modifi-
chi il regime di giri minimo del motore e che la
manopola acceleratore ritorni dolcemente e automa-
ticamente in posizione di riposo, quando viene rila-
sciata.
Se necessario:
Intervenire sul pomello di registro (4), lato sinistro del
veicolo.
AVVITANDO (senso orario), il numero di giri aumenta.
SVITANDO (senso antiorario), il numero di giri diminui-
sce.
Agendo sulla manopola acceleratore, accelerare e de-
celerare alcune volte per controllare il corretto funzio-
namento e se il minimo rimane stabile.
Se necessario intervenire sulla vite aria (5) utilizzan-
do lapposito cacciavite a 90, vedi 1.8 (ATTREZZI
SPECIALI).
2 - 16
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
a
Tras haber finalizado el ajuste, controle que la Put the protection guard in place again (1)
rotacin del manillar no modifique el rgimen
a
del ralent del motor, y que al soltar el puo de After completing the adjustment, check that
mando del acelerador, ste vuelva suave y automti- the rotation of the handlebar does not modify
camente a la posicin de reposo. the idling rpm of the engine and that the accel-
erator handgrip returns smoothly and automatically
into a rest position when released.
Si es necesario: If necessary:
Acte sobre el pomo de regulacin (1), lado izquierdo Adjust the knob (1) positioned on the left side of the ve-
del vehculo. hicle.
ATORNILLANDO (en sentido horario) aumenta el n- By SCREWING IT (clockwise), you increase the en-
mero de las revoluciones. gine rpm.
DESTORNILLANDO (en sentido antihorario) disminu- By UNSCREWING IT (anticlockwise), you decrease
ye el nmero de las revoluciones. the engine rpm.
Actuando sobre el puo de gas, acelere y decelere al- Twist the throttle grip, accelerating and decelerating a
gunas veces para controlar el funcionamiento correcto few times to make sure that it functions correctly and
y si el ralent queda estable. to check if the idling speed is constant.
Si resulta necesario acte sobre el tornillo aire (5) If necessary, adjust the air screw (5) by means of the
utilizando el destornillador correspondiente a 90, apposite 90 screwdriver, see 1.8 (SPECIAL TOOLS).
vase 1.8 (EQUIPOS ESPECIALES).
2 - 17
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Dopo aver completato la regolazione, verifica-
re che la rotazione del manubrio non influisca
sul regime di giri del motore.
2 - 18
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
a
On completion of adjustment check that the
a
Tras haber finalizado el ajuste, controle que la rotation of the handlebar does not influence
rotacin del manillar no modifique el rgimen the engine rpm.
del ralent del motor.
Para ajustar el embrague, efecte la siguiente operacin: To adjust the clutch, proceed as follows:
Apoye el vehculo sobre el soporte. Position the vehicle on stand.
Extraiga la envoltura de proteccin (5). Remove the protection guard (5).
Afloje la contratuerca (6). Loosen the lock nut (6).
Gire el regulador (7) hasta que el juego en vaco de la Rotate the adjuster (7) until the idle stroke of the clutch
palanca de mando del embrague sea de 10 mm. lever is ca. 10 mm.
aproximadamente. Tighten the lock nut (6) and check the adjustment
Apriete la contratuerca (6) y controle nuevamente el again.
ajuste. Put the protection guard in place again (5)
Coloque nuevamente la envoltura de proteccin (5). Switch on the engine and engage the 1st gear, making
Arranque el motor y ponga la 1 marcha, cercirese sure that the engine does not stop or that the vehicle
que el motor no se pare o que el vehculo no tienda a does not tend to move ahead or the clutch slip during
avanzar, o bien, que el embrague no patine durante la the phase of acceleration or during a run.
c
aceleracin o la marcha.
c
Make sure the clutch cable is sound: it should
Controle que el cable del embrague est sano: not have flattened parts and the sheath
no debe tener la vaina aplastada o gastada en should not be worn at any place along the entire
toda su longitud. length.
2 - 19
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Non oltrepassare la marcatura MAX e non
andare al di sotto della marcatura MIN, per
non causare gravi danni al motore.
2 - 20
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
2.12 CONTROL DEL NIVEL DEL ACEITE 2.12 CHECKING THE ENGINE OIL LEVEL
DEL MOTOR Y RELLENO AND TOPPING UP
Lea con mucha atencin 1.2.2 (ACEITE DEL MO- Read carefully 1.2.2 (ENGINE OIL) and 1.4 (PRECAU-
TOR) y 1.4 (PRECAUCIONES E INFORMACIONES GE- TIONS AND GENERAL INFORMATION).
NERALES).
c
dos ruedas apoyadas sobre el piso.
c
If you fail to carry out the above operations
Si no realiza la operaciones arriba menciona- you will risk making an incorrect measure-
das, la medicin del nivel puede resultar equi- ment of the oil level.
vocada.
Unscrew and take out the plug/dipstick (1)
Desenrosque y extraiga el tapn/varilla de medicin Clean the part in contact with the oil with a clean cloth.
(1).
Insert plug/dipstick completely into inlet hole (2) with-
Limpie la parte que tiene contacto con el aceite con un out screwing it.
pao limpio.
Take out plug/dipstick again (1) and read the oil level:
Introduzca el tapn/varilla en el orifico de introduccin
(2), sin enroscarlo. MAX = maximum level.
MIN = minimum level.
Extraiga nuevamente el tapn/varilla de medicin (1) y
lea el nivel que el aceite alcanz en la varilla: The difference between MAX and MIN is circa
300 cmC.
MAX = nivel mximo.
MIN = nivel mnimo. The level is correct if oil approximately reaches the
MAX mark on the dipstick.
La diferencia entre MAX y MIN es de 300 cm C
a
aproximadamente. Do not exceed the MAX mark nor allow oil to
El nivel es correcto cuando se acerca al nivel MAX, go below the MIN mark in order to avoid seri-
que est sealado sobre la varilla de medicin. ous damage to the engine.
a
Para no provocar graves daos al motor, el ni- If necessary, top up the engine oil tank through the in-
vel no debe sobrepasar la marca MAX y no let hole (2) after removing the plug/dipstick (1).
debe quedar por debajo de la marca MIN.
2 - 21
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Utilizzando il veicolo in zone polverose, si
consiglia di sostituire lolio pi frequentemen-
te.
a
Il motore riscaldato contiene olio ad alta tem-
peratura, porre p a r t i c o l a r e a t t e n z i o n e a
n o n scottarsi durante lo svolgimento delle
operazioni successive.
2 - 22
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
2.13 CAMBIO DEL ACEITE MOTOR Y DEL 2.13 CHANGING ENGINE OIL
FILTRO DEL ACEITE DEL MOTOR AND OIL FILTER
Lea con mucha atencin 1.2.2 (ACEITE DEL MO- Read carefully 1.2.2 (ENGINE OIL) and 1.4 (PRECAU-
TOR) y 1.4 (PRECAUCIONES E INFORMACIONES GE- TIONS AND GENERAL INFORMATION).
NERALES).
Change it after the first 1000 km (or 4 months) and suc-
Sustitya tras los primeros 1000 km (o 4 meses) y luego cessively every 6000 km (or 12 months).
cada 6000 km (o 12 meses).
a
Utilizando el vehculo en zonas polvorientas,
es aconsejable cambiar el aceite ms frecuen-
temente.
a We recommend changing the oil more fre-
quently if vehicle is used in dusty areas.
Tras un largo perodo de uso, el aceite motor se deteriora After a long period of use, engine oil deteriorates and
y acelera el desgaste de las superficies acopladas y de hastens the wear of sliding or connecting surfaces.
deslizamiento. Cmbielo peridicamente, realizando las Change engine oil periodically, proceeding as follows:
siguientes operaciones: Switch off engine and let it cool down for at least 10
Pare el motor y djelo enfriar al menos por diez minu- minutes, thus allowing the oil to flow back into the oil
tos para permitir el drenaje del aceite en el crter y el pan and cool down.
enfriamiento del aceite mismo. Start the engine and let it idle for a few minutes to facil-
Arranque el motor y djelo funcionar al ralent de las itate the flow of oil into the oil pan during the succes-
c
revoluciones por algunos minutos, de esta manera el sive phase of draining.
c
aceite saldr ms fcil durante el drenaje sucesivo.
Position the vehicle on firm and flat ground.
Coloque el vehculo sobre un suelo firme y lla-
no.
Keep vehicle in a vertical position with the two wheels
Mantenga el vehculo en posicin vertical, con las dos resting on the ground.
ruedas apoyadas sobre el suelo.
a
When warmed up, the engine contains very
a
El motor caliente contiene aceite muy calien-
hot oil; pay particular attention not to be burnt
te, por lo tanto, tenga cuidado en no quemar-
during the course of the following operations.
se durante las operaciones sucesivas.
Desenrosque y extraiga el tapn-varilla de medida (1). Unscrew and extract the plug/dipstick (1).
Desmonte del protector, vase 7.1.9 (DESMONTAJE Remove the oil pan, see 7.1.9 (REMOVING THE OIL
PROTECTOR DE CARTER). PAN GUARD).
Coloque un recipiente (2) con capacidad no inferior a Put a container (2) with at least 2500 cmC capacity in
2500 cmC en correspondencia con el tapn de vaciado correspondence with the drain plug (3) on the frame.
(3) sobre el bastidor. Unscrew and remove the drain plug (3) positioned on
Desenrosque y quite el tapn de vaciado (3) sobre el the frame.
bastidor. Drain the oil and let it drip into the container (2) for a
Vace y deje gotear el aceite dentro del recipiente (2) few minutes.
por algunos minutos. Check and if necessary change the sealing washer of
Controle y si acaso sustituya la arandela de estanquei- the drain plug (3) positioned on the frame.
dad del tapn de vaciado (3) sobre el bastidor. Screw and tighten the drain plug (3) positioned on the
Enrosque y apriete el tapn de vaciado (3) sobre el frame.
bastidor.
Driving torque of the drain plug (3) positioned on the
Par de apriete tapn de vaciado (3) sobre el bastidor:
frame: 27 Nm (2.7 kgm).
27 Nm (2,7 kgm).
Desplace el recipiente (2) y pngalo por debajo de la Move the container (2) and position it under the engine
base del motor, en correspondencia con el tapn de base, in correspondence with the drain plug positioned
vaciado sobre el motor (4). on the engine (4).
Desenrosque y quite el tapn de vaciado sobre el mo- Unscrew and remove the drain plug positioned on the
tor (4). engine (4).
Vace y deje gotear el aceite dentro del recipiente (2) Drain the oil and let it drip inside the container (4) for a
por algunos minutos. few minutes.
Par de apriete tapn de vaciado sobre el motor (4): Driving torque of the drain plug (4) positioned on the
40 Nm (4 kgm). engine: 40 Nm (4 kgm).
2 - 23
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Lo spurgo dellaria deve essere sempre effet-
tuato quando lolio stato scaricato comple-
tamente sia dal serbatoio che dal motore (revi-
sione motore).
a
Le operazioni che seguono devono essere
svolte durante le fasi per la sostituzione olio
dopo avere tolto il filtro olio sul motore e pri-
ma di rimontarne uno nuovo.
2 - 24
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Limpie el filtro aceite motor sobre el bastidor (1) cada Clean the engine oil filter positioned on the frame (1)
12000 km (o cada dos veces que se sustituye el acei- every 12000 km (or every second engine oil change).
c
te motor).
c
Prepare a pipe clamp (2) to replace the origi-
Prepare una abrazadera de manguera tipo des- nal one (special type).
tornillador (2) para sustituirla a la original (de
tipo especial). Loosen the clamp (3) and disconnect the pipe (4).
Unscrew and remove the engine oil filter positioned on
Afloje la abrazadera (3) y desempalme el tubo (4).
the frame (1) and clean it with a compressed air jet.
Destornille y saque el filtro aceite motor (1) sobre el
Check the seal of the engine oil filter positioned on the
bastidor y lmpielo con un chorro de aire comprimido.
frame (1), screw and tighten it.
Controle la junta del filtro aceite motor (1) sobre el bas-
tidor, enrsquelo y apritelo. Driving torque of the engine oil filter (1) positioned
on the frame: 35 Nm (3.5 kgm).
Par de apriete filtro aceite motor (1) sobre el basti-
dor: Connect the pipe (4) and tighten the new clamp (2).
35 Nm (3,5 kgm).
Change the engine oil filter (7) after the first 1000 km
Empalme el tubo (4) y apriete la nueva abrazadera (2).
and successively every 6000 km (or every time you
Sustituya el filtro aceite motor (7) tras los primeros change the oil).
1000 km y luego cada 6000 km (o cada vez que se
sustituye el aceite motor). Unscrew the two screws (5) and remove the cover (6).
Remove the engine oil filter (7).
Destornille los dos tornillos (5) y quite la tapa (6).
Spread an oil film on the sealing ring of the new engine
Saque el filtro aceite motor (7).
oil filter.
Aplique una ligera capa de aceite sobre la junta trica
Fit the new engine oil filter.
del nuevo filtro aceite motor.
Put back the cover (6), screw and tighten the two
Introduzca el nuevo filtro aceite motor.
screws (5).
Vuelva a instalar la tapa (6), atornille y apriete los dos
Pour about 1600 cmC of engine oil through the filling
tornillos (5).
opening (9), see 1.7 (LUBRICANT CHART).
Vierta por la abertura de llenado (9) unos 1600 cmC de
Tighten the plug/dipstick (8).
aceite motor, vase 1.7 (TABLA DE LOS LUBRI-
Start the engine and let it idle for about one minute, in
CANTES).
order to ensure the filling up of the engine oil circuit.
Enrosque el tapn -varilla (8).
Unscrew and extract the plug/dipstick (8).
Ponga en marcha el motor y djelo funcionar al ralent
Pour other 600 cmC of oil through the filling opening
por un minuto ms o menos para que el circuito aceite
(9).
motor se llene.
Check the oil level, see 2.12 (CHECKING THE EN-
Desenrosque y extraiga el tapn-varilla (8).
GINE OIL LEVEL AND TOPPING UP).
Vierta por la abertura de llenado (9) otros 600 cmC de
aceite.
Controle el nivel del aceite, vase 2.12 (CONTROL
DEL NIVEL DEL ACEITE DEL MOTOR Y RELLENO).
a a
La purga del aire debe efectuarse siempre The bleeding of air must always be carried out
cuando el aceite ha sido descargado comple- when the oil has been completely discharged
tamente, tanto del depsito como del motor from both tank and engine (engine overhaul).
(revisin motor).
a
The following operations are to be performed
a
Hay que realizar las siguientes operaciones during the phases of changing oil after remov-
durante el cambio de aceite apenas se ha qui- ing the oil filter on the engine and before at-
tado el filtro de aceite sobre el motor y antes taching the new one.
de montar otras vez uno nuevo.
Unscrew and remove the small valve (10) located on
Desenrosque y quite la valvulita (10), que est coloca- the bottom of the engine oil filter housing.
da en el fondo del alojamiento del filtro del aceite mo- Position the ignition switch on n.
tor. Position the engine stop switch on m (11).
Coloque el interruptor de arranque en la posicin n. Press the starter button r (12) and run the starter
Coloque el interruptor de parada motor (11) en la posi- until oil begins to escape from the seat of the small
cin m. valve (10) (a few seconds are sufficient).
Apriete el pulsador de arranque r (12) y haga fun- Insert and completely screw the valve (10).
cionar el motor de arranque, hasta que desde el asien-
to de la valvulita (10) comience a salir aceite (son sufi-
cientes algunos segundos).
Introduzca y enrosque completamente la valvulita
(10).
2 - 25
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Non togliere il tappo del vaso di espansione a
motore caldo, perch il refrigerante sotto
pressione e a temperatura elevata.
a
Nel caso di consumo eccessivo di liquido re-
frigerante e nel caso in cui il vaso di espansio-
ne (1) rimanga vuoto, controllare che non ci
siano perdite nel circuito.
2 - 26
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con mucha atencin 1.2.5 (LQUIDO REFRIGE- Read carefully 1.2.5 (COOLANT) and 1.4 (PRECAU-
RANTE) y 1.4 (PRECAUCIONES E INFORMACIONES TIONS AND GENERAL INFORMATION).
GENERALES).
Check every 1000 km.
Controle cada 1000 km.
a
Do not remove the expansion tank cap when
a
No quite el tapn del depsito de expansin the engine is hot, since the coolant is under
con el motor an caliente, porque el lquido pressure and its temperature is high.
refrigerante est bajo presin y a temperatura
a
elevada.
Check the coolant level and top up the expan-
a
sion tank with cold engine.
Realice las operaciones de control y de relle-
no del lquido refrigerante con el motor fro. Stop the engine and wait until it has cooled down.
Keep the vehicle in vertical position, with the two
wheels resting on the ground.
Make sure that the level of the fluid contained in the
Mantenga el vehculo en posicin vertical con las dos expansion tank (1) is included between the "MIN" and
ruedas apoyadas sobre el suelo. "MAX" marks (see figure).
Controle que el nivel del lquido, contenido en el dep- If not, unscrew and remove the filling plug (2).
sito de expansin (1), est comprendido entre las refe- Top up until the fluid reaches approx. the "MAX" mark.
rencias "MIN" y "MAX" (vase figura). Do not exceed this level, otherwise the fluid will flow
En caso contrario, desenrosque y quite el tapn de lle- out of the tank when the engine is running.
nado (2). Put back the filling plug (2).
Rellene hasta que el nivel del lquido alcance aproxi-
a
madamente el nivel "MAX". No supere este nivel, In case of excessive consumption of coolant
porque en caso contrario puede haber una salida del and in case the expansion tank (1) remains
lquido durante el funcionamiento del motor. empty, make sure that there are no leaks in
Vuelva a poner el tapn de llenado (2). the circuit.
a
En caso de un excesivo consumo de lquido
refrigerante y en caso de que el depsito de
expansion (1) quede vaco, controle que no
haya prdidas en el circuito.
2 - 27
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
2.15 SOSTITUZIONE
DEL LIQUIDO REFRIGERANTE
a
Non togliere il tappo del radiatore a motore
caldo, perch il liquido refrigerante sotto
pressione e a temperatura elevata.
2 - 28
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
a
Substituya lquido refrigerante cada 2 aos.
Allow the engine to cool down to room tem-
a
perature.
Deje enfriar el motor hasta que el mismo al-
cance la temperatura ambiente. Remove the oil pan, see 7.1.9 (REMOVING THE OIL
PAN GUARD).
Desmonte del protector, vase 7.1.9 (DESMONTAJE Remove the front fairing, see 7.1.14 (REMOVING
PROTECTOR DE CARTER). THE FRONT FAIRING).
Desmonte el carenado delantero, vase 7.1.14 (DES- Place a container under the drain plug (3) to collect the
MONTAJE CARENADO DELANTERO). liquid (ca. 1,4 l ).
Coloque un recipiente abajo del tapn de drenaje (3) Unscrew and remove the drain plug (3) recovering the
para recoger el lquido ( 1,4 l aproximadamente). copper washer.
Desenrosque y quite el tapn de drenaje (3), guardan-
a
do la arandela de cobre. Do not remove the radiator plug when the en-
gine is hot as the coolant is under pressure
a
No quite el tapn del radiador con el motor ca- and is very hot.
liente, ya que el lquido refrigerante est bajo
presin y muy caliente. To facilitate the liquid outflow, rotate the radiator plug
(4) anticlockwise of one step.
Para facilitar la salida del lquido, gire en sentido anti- Wait a few seconds, in order to allow any residual
horario y de un resorte el tapn (4) del radiador. pressure present in the system to be eliminated.
Espere unos segundos para permitir la purga de la Rotate the radiator plug (4) anticlockwise again and re-
eventual presin presente en la instalacin. move it.
Gire otra vez en sentido antihorario el tapn (4) del ra- Rinse out the radiator with clean water.
diador y extrigalo.
Enjuague el radiador con agua limpia. DO NOT DISPOSE OF ENGINE OIL IN THE ENVIRON-
MENT.
NE ESPARZA EL ACEITE EN EL AMBIENTE.
In reassembling, apply LOCTITE 574 on the thread of
Coloque LOCTITE 574 en la rosca del tapn de drenaje the drain plug (3).
(3) al montarlo nuevamente. Reassemble the drain plug (3) with a new copper
Monte nuevamente el tapn de drenaje (3) con una washer.
nueva arandela de cobre.
Driving torque of drain plug (4): 12 Nm (1,2 kgm)
Par de apriete del tapn de drenaje (4):
12 Nm (1,2 kgm) Top up the radiator until filling it completely.
Rellene el radiador. Repeatedly press the two couplings (5-6) with your
Con la mano presione y suelte algunas veces los dos
hand and release them, in such a way as to create a
manguitos (5-6) para crear una ligera presin permi- slight pressure and to allow the liquid to flow into the
tiendo el fluir del lquido en los tubos. pipes.
Top up the radiator again until filling it completely.
Rellene otra vez el radiador.
Put the plug back on radiator (4).
Coloque nuevamente el tapn del radiador (4).
Remove the cap (2) from expansion tank (1).
Quite el tapn (2) del depsito de expansin (1).
Top up until the liquid reached the MAX level, see
Rellene hasta que el nivel del lquido alcance aproxima-
damente el nivel MAX, vase 1.7 (TABLA DE LOS 1.7 (LUBRICANT CHART). Do not exceed this level
LUBRICANTES). No supere dicho nivel, de otra mane- otherwise there will be an escape of the coolant during
ra el lquido saldr durante el funcionamiento del motor. running of the engine.
Reinsert the cap (2) of the expansion tank (1).
Introduzca nuevamente el tapn (2) del depsito de
expansin (1). Start the engine and let it run for a few minutes, then
c
this vehicle.
No est prevista la operacin de purga aire de
la instalacin por no ser necesaria en este ve- For further information see 5.0 (COOLING SYSTEM).
hculo.
2 - 29
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con mucha atencin 1.4 (PRECAUCIONES E IN- Read 1.4 carefully (PRECAUTIONS AND GENERAL
FORMACIONES GENERALES). INFORMATION).
Controle cada 500 km. Lubrique cada 1000 km. Check every 500 km. Lubricate every 1000 km.
El vehculo est equipado con una cadena sin fin rema- The vehicle is fitted with an endless chain, which does
chada (sin enganche). not utilise the connecting link.
Tipo de cadena: DID modelo 520 V6 Chain type: DID mod. 520 V6
a a
La cadena de transmisin est equipada de The driving chain is equipped with O rings be-
juntas toricas entre los eslabones, que sirven tween the links designed to keep the grease
para mantener la grasa en el interior. Tenga on the inside.
mucho cuidado cuando realice el ajuste, lubricacin, Use the maximum caution in adjusting, lubricating,
limpieza y substitucin de la cadena. washing and replacing the chain.
Coloque el vehculo sobre un caballete de sostn y gire Position the vehicle on the special stand and slowly ro-
con la mano la rueda trasera con el cambio en punto tate, manually, the rear wheel with the gear in neutral.
muerto. Visually check that the chain presents none of the defects
Controle visualmente que la cadena de transmisin no listed below:
tenga ninguno de los defectos indicados a continuacin. Pins loosened
Pernos flojos. Rollers damaged
Rodillos daados. Links rusted or seized
Eslabones oxidados o agarrotados. Links deformed or with rims
Eslabones deformados o aplastados. Excessive wear
Desgaste excesivo. Chain not adjustable correctly
Cadena no ajustada correctamente. Leak of O rings
Prdida de juntas tricas. If the chain presents even one of the listed defects, it
Hay que substituir la cadena si presenta uno solo de los must be replaced, see 7.1.23 (REMOVING THE GEAR-
defectos indicados, vase 7.1.23 (DESMONTAJE CA- ING CHAIN).
DENA DE TRANSMISION).
a a
Si la cadena est muy floja, puede suceder An excessive slackening of the chain may
que sta se salga del pin, provocando un cause it to come away from the pinion, causing
accidente o graves daos al vehculo y a per- an accident or serious damage to the vehicle
sonas. and people.
a a
De no realizar correctamente el mantenimien- Incorrect maintenance may cause the untime-
to, se puede causar el desgaste prematuro de ly wear of the chain and/or damages to the
la cadena o daar el pin y/o la corona. Reali- pinion and/or the crown.
ce las intervenciones de mantenimiento ms frecuen- Carry out the maintenance operations more frequent-
temente si utiliza el vehculo en condiciones difciles o ly if you use the vehicle in difficult conditions or on
sobre carreteras polvorientas y/o con barro dusty and/or muddy roads.
2 - 31
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
2.16.3 REGOLAZIONE
Se dopo i controlli si rende necessaria la regolazione del-
la tensione catena:
Bloccare, con lapposita chiave, la rotazione del perno
ruota (1).
c
Allentare il dado (2).
a
Non utilizzare tricloroetilene, benzina o altri li-
quidi similari: posssono avere un potere dis-
solvente eccessivo per questa catena e, cosa
pi importante, possono danneggiare le guarnizioni
OR che trattengono il grasso negli interstizi tra i rulli-
ni e i perni.
Dopo aver lavato e fatto asciugare la catena, lubrificar-
la con grasso spray per catene sigillate, vedi 1.7 (TA-
BELLA LUBRIFICANTI).
a
Non usare comunque lubrificanti reperibili in
commercio non specifici per catene sigilla-
te: possono danneggiare le guarnizioni OR.
a
La catena standard del tipo DID modello 520
V6. Per la sostituzione, si raccomanda limpie-
go di una catena uguale.
2 - 32
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
c c
Afloje la tuerca (2). Loosen the nut (2).
Para el centrado de la rueda estn previstas For the wheel centering numbered reference
algunas referencias numeradas relacionadas marks are provided, which are connected with
al movimiento de los tensores (3) y (4). Estas referen- the movement of the adjusters (3) and (4). These ref-
cias se encuentran dentro de dos ranuras (5) y (6) co- erence marks can be seen inside two slots (5) and (6)
locadas en los brazos de la basculante, anteriormen- positioned on the rods of the rear fork, before the
te al eje de la rueda. wheel pin.
Acte sobre los tensores izquierdo (3) y derecho (4) y Act on the left (3) and right (4) adjusters and adjust the
ajuste el juego de la cadena controlando en ambos la- chain slack, making sure that the slots (5) and (6) coin-
dos del vehculo que en las ranuras (5) y (6) corres- cide with the same reference marks on both sides of
pondan las mismas referencias. the vehicle.
Bloquee la rotacin del eje de la rueda (1) utilizando la Lock the wheel pin (1) rotation by means of the suita-
llave correspondiente. ble spanner.
Apriete la tuerca (2). Tighten the nut (2).
Par de apriete tuerca-eje rueda (1-2): Wheel pin-nut driving torque (1-2):
100 Nm (10 Kgm). 100 Nm (10 kgm).
Compruebe el juego de la cadena, vase 2.16.1 Check the chain slack, see 2.16.1 (CLEARANCE
(CONTROL DEL JUEGO). CONTROL).
a
Do not use trichloroethylene, petrol, or other
a
No utilice tricoloroetileno, gasolina u otros l- similar liquids: they may have an excessive
quidos similares: pueden tener un poder di- dissolving power for this chain and, even
solvente excesivo para este tipo de cadena y, more important, they can damage the O-rings that
lo que es ms importante, pueden daar las juntas hold the grease in the gaps between the rollers and
tricas que retienen la grasa en los intersticios entre the pins.
los rodillos y los pernos.
After washing and drying the chain, lubricate it with a
Tras haber limpiado y dejado secar la cadena, lubr- spray grease for sealed chains, see 1.7 (LUBRICANT
quela con grasa spray para cadenas cerradas, vase CHART).
1.7 (TABLA DE LOS LUBRICANTES).
a
In any case, do not use lubricants found on
a
De todas maneras, no utilice lubricantes que the market which are not specific for sealed
no sean especficos para cadenas hermti- chains: they can damage the O-rings.
cas: pueden daar las juntas tricas.
a
The standard chain is the DID type 520 V6
a
La cadena estndar es del tipo DID modelo model. When replacing, we recommend using
520 V6. Para substituirla, utilice una cadena the same model.
igual.
2 - 33
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Nel caso di una corsa eccessiva della leva fre-
no, di eccessiva elasticit o nel caso di pre-
senza di bolle daria nel circuito, effettuare lo
spurgo dellaria dallimpianto.
c
no inavvertitamente allinterno del circuito.
Posizionare il veicolo su di un terreno solido e
in piano.
Tenere il veicolo in posizione verticale e ruotare il ma-
nubrio in modo che il liquido contenuto nel serbatoio
sia parallelo al coperchio serbatoio liquido freni.
Verificare che il liquido contenuto nel serbatoio superi
il riferimento MIN.
Se il liquido non raggiunge almeno il riferimento MIN,
provvedere al rabbocco.
Rabbocco
a
Pericolo di fuoriuscita liquido freni.
Non azionare la leva freno anteriore con le viti
(2) allentate o, soprattutto, con il coperchio
serbatoio liquido freni rimosso.
Svitare le due viti (2) del serbatoio liquido freni (3).
c
Rimuovere il coperchio (4).
Per non spandere il liquido dei freni durante il
rabbocco, si raccomanda di mantenere il liqui-
do nel serbatoio parallelo al bordo serbatoio (in posi-
zione orizzontale).
Rimuovere la guarnizione (5).
Riempire il serbatoio (3) con liquido freni, vedi 1.7
(TABELLA LUBRIFICANTI), sino a coprire completa-
mente il vetrino (1).
Per il rimontaggio dei componenti, seguire il procedi-
mento inverso.
2 - 34
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con mucha atencin 1.2.4 (LQUIDO DE FRE- Read carefully 1.2.4 (BRAKE FLUID) and 1.4 (PRE-
NOS) y 1.4 (PRECAUCIONES E INFORMACIONES CAUTIONS AND GENERAL INFORMATION).
GENERALES).
Check brakes after the first 1000 km (or 4 months) and
Controle tras los primeros 1000 km (o 4 meses) y sucesi- then every 6000 kms (or 8 months).
a
vamente, cada 6000 km (o 8 meses). In case of excessive stroke of the brake lever,
a
En caso de una carrera excesiva de la palanca of excessive elasticity or in case there is air in
del freno, de excesiva elasticidad o en caso the circuit to bleed the system.
de presencia de burbujas de aire en el circuito
efectuar la purga del aire del sistema. The leak of brake fluid damages painted or plastic
surfaces.
Las prdidas del lquido de freno daan las superfi- Before setting out, make sure that the cables are not
cies barnizadas o de plstico. twisted or holed and that there are no leakage from
Antes de salir, controle que las tuberas no estn re- the connectors.
torcidas o fisuradas y que no haya prdidas en las
uniones. The braking systems on this vehicle have been filled
Los sistemas de frenado de este vehculo han sido with a glycol-based liquid.
llenados con lquido a base de glicol. Do not use or mix different types of silicone or oil-
No use o mezcle diferentes tipos de lquidos a base based liquids. Do not use brake fluids taken from old
de siliconas o de petrleo. containers, used or not sealed.
No utilice lquidos que hayan estado en envases vie- Do not use liquids left over from earlier repair jobs
jos, usados o no cerrados hermticamente and stored for long periods.
No utilice nuevamente lquido que haya sobrado de
a
reparaciones anteriores y haya estado almacenado
por mucho tiempo. Make sure that neither water nor dust acciden-
tally enter the circuit.
c
en el interior del circuito.
Coloque el vehculo sobre un suelo firme y lla- Keep the vehicle in vertical position and rotate the han-
no. dlebar, so that the fluid contained in the tank is parallel
to the brake fluid tank cover.
Mantenga el vehculo en posicin vertical y gire el ma- Make sure that the fluid level exceeds the "MIN" mark.
nillar de manera que el lquido contenido en el depsi- If the fluid does not reach the "MIN" mark, provide for
to quede paralelo a la tapa del depsito lquido frenos. topping up.
Compruebe que el lquido contenido en el depsito su-
pere la referencia "MIN" .
Si el lquido no llega por lo menos hasta la referencia
"MIN" , rellene enseguida.
Topping up
Relleno
a
The brake fluid may flow out of the tank.
a
Peligro de salida lquido frenos. Do not operate the front brake lever if the
No accione la palanca del freno delantero si screws (2) are loose or, most important, if the
los tornillos (2) estn aflojados o, sobre todo, brake fluid tank cover has been removed.
si se ha quitado la tapa del depsito lquido frenos.
Unscrew the two screws (2) of the brake fluid tank (3).
Destornille los dos tornillos (2) del depsito lquido fre- Remove the cover (4).
c
nos (3).
Quite la tapa (4). In order not to spill the brake fluid while top-
2 - 35
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Nel caso di una corsa eccessiva della leva fre-
no, di eccessiva elasticit o nel caso di pre-
senza di bolle daria nel circuito, effettuare lo
spurgo dellaria dallimpianto.
c
no inavvertitamente allinterno del circuito.
Posizionare il veicolo su di un terreno solido e
in piano.
Tenere il veicolo in posizione verticale in modo che il li-
quido contenuto nel serbatoio (1) sia parallelo al bordo
del serbatoio.
Verificare che il liquido contenuto nel serbatoio superi
il riferimento MIN.
Se il liquido non raggiunge almeno il riferimento MIN,
provvedere al rabbocco.
Rabbocco
Rimuovere la fiancatina laterale destra, vedi 7.1.4
(RIMOZIONE FIANCATINE LATERALI DESTRA E SI-
NISTRA).
a
Pericolo di fuoriuscita liquido freni.
Non azionare la leva freno posteriore con il tap-
po serbatoio liquido freni allentato o rimosso.
c
Svitare e rimuovere il tappo (2).
Per non spandere il liquido dei freni durante il
rabbocco, si raccomanda di mantenere il liqui-
do nel serbatoio parallelo al bordo serbatoio (in posi-
zione orizzontale).
Rimuovere la guarnizione (3).
Riempire il serbatoio (1) con liquido freni, vedi 1.7
(TABELLA LUBRIFICANTI), sino al riferimento MAX.
Per il rimontaggio dei componenti, seguire il procedi-
mento inverso.
2 - 36
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con mucha atencin 1.2.4 (LQUIDO DE FRE- Read carefully 1.2.4 (BRAKE FLUID) and 1.4 (PRE-
NOS) y 1.4 (PRECAUCIONES E INFORMACIONES CAUTIONS AND GENERAL INFORMATION).
GENERALES).
Check brakes after the first 1000 km (or 4 months) and
Controle tras los primeros 1000 km (o 4 meses) y sucesi- then every 6000 kms (or 8 months).
a
vamente, cada 6000 km (o 8 meses). In case of excessive stroke of the brake lever,
a
En caso de una carrera excesiva de la palanca of excessive elasticity or in case there is air in
del freno, de excesiva elasticidad o en caso the circuit.
de presencia de burbujas de aire en el circui-
to. The leak of brake fluid damages painted or plastic
surfaces.
Las prdidas del lquido de freno daan las superfi- Before setting out, make sure that the cables are not
cies barnizadas o de plstico. twisted or holed and that there are no leakage from
Antes de salir, controle que las tuberas no estn re- the connectors.
torcidas o fisuradas y que no haya prdidas en las
uniones. The braking systems on this vehicle have been filled
Los sistemas de frenado de este vehculo han sido with a glycol-based liquid.
llenados con lquido a base de glicol. Do not use or mix different types of silicone or oil-
No use o mezcle diferentes tipos de lquidos a base based liquids. Do not use brake fluids taken from old
de siliconas o de petrleo. containers, used or not sealed.
No utilice lquidos que hayan estado en envases vie- Do not use liquids left over from earlier repair jobs
jos, usados o no cerrados hermticamente and stored for long periods.
No utilice nuevamente lquido que haya sobrado de
a
reparaciones anteriores y haya estado almacenado
por mucho tiempo. Make sure that neither water nor dust acciden-
tally enter the circuit.
c
en el interior del circuito.
Coloque el vehculo sobre un suelo firme y lla- Keep the vehicle in vertical position, so that the fluid
no. contained in the tank (1) is parallel to the, so that the
brake fluid is parallel to the tank edge.
Mantenga el vehculo en posicin vertical de manera Make sure that the fluid level exceeds the "MIN" mark.
que el lquido contenido en el depsito (1) quede para- If the fluid does not reach the "MIN" mark, provide for
lelo al, quede paralelo al borde del depsito. topping up.
Compruebe que el lquido contenido en el depsito su-
pere la referencia "MIN" .
Si el lquido no llega por lo menos hasta la referencia
"MIN" , rellene enseguida.
Topping up:
Relleno Remove the right side, see 7.1.4 (REMOVING THE
Desmonte el panel lateral derecho, vase 7.1.4 RIGHT AND LEFT SIDES).
(DESMONTAJE PANELES LATERALES DERECHO
a
E IZQUIERDO). The brake fluid may flow out of the tank.
Do not operate the rear brake lever if the brake
a
Peligro de salida lquido. No accione la palan- fluid tank plug is loose or has been removed.
ca del freno trasero si se ha aflojado o quitado
el tapn del depsito lquido frenos. Unscrew and remove the plug (2).
c
ping up, keep the fluid in the tank parallel to
Para no verter el lquido de los frenos durante the tank rim (in horizontal position).
el relleno, se recomienda mantenga el lquido
en el depsito paralelo al borde del depsito (en po- Remove the gasket (3).
sicin horizontal). Fill the tank (1) with brake fluid, see 1.7 (LUBRICANT
CHART), until it reaches the "MAX" mark.
Quite la junta (3). To reassemble the components, follow the reverse or-
Llene el depsito (1) con el lquido frenos, vase 1.7 der.
(TABLA DE LOS LUBRICANTES), hasta la referencia
"MAX" .
Para volver a instalar los componentes, acte siguien-
do el procedimiento en orden contrario.
2 - 37
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Manipolare il liquido freni con attenzione: alte-
ra chimicamente la vernice e le parti in plasti- 1
ca, gomma, ecc.
a
Considerando la pericolosit per il veicolo e
per il pilota, assolutamente indispensabile,
dopo il rimontaggio dei freni e il ripristino
dellimpianto frenante alle normali condizioni duso,
che il circuito idraulico sia spurgato dallaria, proce-
dendo nel modo seguente:
2 - 38
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con mucha atencin 1.2.4 (LQUIDO DE FRE- Read carefully 1.2.4 (BRAKE FLUID) and 1.4 (PRE-
NOS) y 1.4 (PRECAUCIONES E INFORMACIONES CAUTIONS AND GENERAL INFORMATION).
GENERALES).
The air present in the hydraulic system acts as a bearing,
El aire presente en el sistema hidrulico, acta como un absorbing most of the pressure exerted by the brake
almohadn, absorbiendo la mayor parte de la presin pump and reducing the effectiveness of the caliper action
ejercida por la bomba de frenos y reduciendo la eficiencia during braking.
de la pinza durante el frenado. The presence of air is demonstrated by the sponginess
La presencia de aire se manifiesta con la esponjosidad of the brake control and by the reduced braking capacity.
del mando de freno y la reduccin de la capacidad fre-
a
nante. Handle brake fluid with care; it may chemical-
ly alter painted surfaces and the parts in plas-
a
Manipulee el lquido de frenos con mucho cui- tic, rubber, etc.
dado: arruina qumicamente la pintura y las
piezas de plstico, goma, etc. DO NOT DISPOSE OF ENGINE OIL IN THE ENVIRON-
MENT.
NE ESPARZA EL ACEITE EN EL AMBIENTE.
a
Considering the danger for both driver and ve-
a
Considerando que es muy peligroso para el hicle, it is absolutely essential to bleed the hy-
vehculo y para el piloto, es absolutamente in- draulic system after reassembly of the brakes
dispensable, tras la reinstalacin de los fre- and the restoration of the braking system to its nor-
nos y el restablecimiento del sistema frenante a las mal conditions, proceeding as follows:
condiciones normales para el uso, que el circuito hi-
drulico sea purgado, procediendo del siguiente mo- Top up the brake fluid tank, see 2.17 (CHECKING
do: AND TOPPING UP THE FRONT BRAKE FLUID) and
2.18 (CHECKING AND TOPPING UP THE REAR
Realice el relleno lquido frenos en el depsito, vanse BRAKE FLUID).
2.17 (CONTROL Y RELLENO LIQUIDO FRENO DE- Remove the rubber protection cap.
LANTERO) y 2.18 (CONTROL Y RELLENO LIQUI- Insert a transparent plastic tube on the bleeder (1) of
DO FRENO TRASERO). the caliper and put the other end of the tube in a con-
Quite el casquillo protector de goma. tainer.
Introduzca un tubo de plstico transparente en la vl- Rapidly pull and release the brake lever several times,
vula de purga (1) de la pinza e introduzca la otra extre- then keep it completely pulled.
midad del tubo en un recipiente de recogida. Loosen the bleeder one fourth turn so that the brake
Accione y suelte rpidamente algunas veces la palan- fluid flows into the container; this eliminates the ten-
ca, mantenindola, luego, accionada completamente. sion on the brake lever, allowing it to come in contact
Afloje el tornillo de purga de 1/4 de vuelta de manera with the handgrip.
que le lquido frenos entre en el recipiente; esto elimi- Tighten the bleeder (1), pull the lever several times,
nar la tensin sobre la palanca del freno llevndola then keep it completely pulled and unscrew the bleed-
hasta el tope. A este punto apriete la vlvula de purga ing screw again.
(1), accione algunas veces la palanca, luego mantn- Repeat this operation until the liquid flowing into the
gala accionada al mximo y destornille otra vez el tor- container is completely free of air bubbles.
c
nillo de purga.
Repita la operacin hasta que el lquido que llega al During the bleeding of the braking system, fill
recipiente est completamente sin burbujas de aire. the tank with as much brake fluid as needed.
c
Make sure that brake fluid is always present in the
Durante la purga del sistema hidrulico, llene tank during the operation.
el depsito de frenos cuando sea necesario.
Controle que durante la operacin, haya siempre l- Tighten the bleeder and remove the plastic tube.
quido de freno en el depsito.
Driving torque of bleeder (1): 15 Nm (1.5 kgm).
Apriete la vlvula de purga y quite el tubo. Top up the brake fluid tank to the right level.
Put back the rubber protection cap.
Par de apriete de la vlvula de purga (1):
15 Nm (1,5 kgm).
Rellene hasta alcanzar el nivel correcto de lquido fre-
nos en el depsito.
Vuelva a poner el casquillo protector de goma.
2 - 39
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Accertarsi della presenza di gioco tra registro
freno (2) e battuta, per evitare che il freno ri-
manga azionato causando una prematura
usura degli elementi frenanti.
Gioco tra registro freno e battuta: 0,5 1 mm.
Bloccare lastina comando pompa tramite il controda-
do (3).
a
La vite (6) deve essere a contatto sul pompan-
te ma non deve premere oltre, altrimenti si
avr una minima ma continua frenatura.
2 - 40
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
a a
Controle que haya juego entre el tensor del Make sure that there is a certain clearance be-
freno (2) y el elemento de contacto, para evitar tween the brake adjuster (2) and the point of
que el freno quede accionado causando un contact, to prevent the brake from remaining
desgaste prematuro de los elementos de frenado. operated and the consequent untimely wear of the
braking elements.
Juego entre el tensor del freno y el elemento de con-
tacto: 0,5 1 mm. Clearance between brake adjuster and point of con-
tact: 0.5 1 mm.
Bloquee la varilla mando bomba por medio de la con-
tratuerca (3). Lock the pump control rod by means of the lock nut (3).
2.21 AJUSTE DE LA PALANCA DEL FRENO 2.21 FRONT BRAKE LEVER ADJUSTMENT
DELANTERO
If play is observed in the movement of the lever (5) pro-
Si comprueba que la palanca (5) tiene juego, proceda de ceed as follows:
la siguiente manera: Position the vehicle on stand.
Apoye el vehculo sobre el soporte. Adjust the screw (6), eliminating the play.
Elimine el juego mediante el tornillo (6).
a
The screw should be in contact with the
a
El tornillo (6) debe tener contacto con el ele- pumping element but must not press beyond
mento bombeador pero no debe presionar it otherwise there will be a minimum but con-
ms all, de otra manera se tendr un frenado tinuous braking.
mnimo pero continuo.
2.22 COMPROBACION DESGASTE PASTILLAS 2.22 CHECKING THE BRAKE PAD WEAR
Controle el desgaste de las pastillas del freno despus Check the brake pad wear after the first 1000 km and
de los primeros 1000 km; luego cada 6000 km. successively every 6000 km.
El desgaste de las pastillas del freno de disco depende The wear of the brake pads depends on the use, on the
del uso, del tipo de conduccin y de la carretera. kind of drive and on the road.
El desgaste es mayor cuando se conduce en carreteras The wear will be greater when the vehicle is driven on
polvorientas o mojadas. dirty or wet roads.
Para realizar un control rpido del desgaste de las pasti- To carry out a rapid checking of the wear of the pads, pro-
llas hay que: ceed as follows:
Colocar el vehculo sobre el caballete, vase pg. 35 Position the vehicle on the stand, see p. 35 (POSI-
(COLOCACION DEL VEHICULO SOBRE EL CABA- TIONING THE VEHICLE ON THE STAND).
LLETE). Carry out a visual checking of the friction material
Efectuar un control visual entre la pinza del freno y las thickness by looking between the brake caliper and
pastillas, actuando: the pads. Proceed:
- desde abajo para la pinza del freno delantero (7). - from below for the front brake caliper (7);
- desde arriba para la pinza del freno trasero (8). - from above for the rear brake caliper (8).
Si el espesor del material de friccin (incluso de una If the thickness of the friction material (even of one pad
sola pastilla) queda reducido al valor aproximado de 1 only) has reduced to about 1 mm, replace both pads,
mm, sustituya ambas pastillas, vase 7.5.1 y 7.6.1 see 7.5.1 and 7.6.1 (CHANGING THE BRAKE PADS).
(SUBSTITUCIN DE LAS PASTILLAS DE FRENO).
2 - 41
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
2.23 PNEUMATICI
Leggere attentamente 1.4 (PRECAUZIONI E INFOR-
MAZIONI GENERALI).
Controllare le condizioni dopo i primi 1000 km (o 4 mesi)
e successivamente ogni 6000 km (o 8 mesi).
La pressione di gonfiaggio deve essere controllata ogni
mese e a temperatura ambiente.
a
Controllare lo stato superficiale e l'usura, in
quanto una pessima condizione dei pneumati-
ci comprometterebbe laderenza alla strada e
la manovrabilit del veicolo. Sostituire il pneumatico
se usurato o se una eventuale foratura nella zona del
battistrada pi larga di 5 mm.
Limite della profondit del battistrada
Anteriore: 2 mm
Posteriore: 2 mm
a
Controllare periodicamente la pressione di
gonfiaggio dei pneumatici a temperatura am-
biente. Se i pneumatici sono caldi, la misura-
zione non corretta.
Effettuare la misurazione soprattutto dopo ogni lun-
go viaggio. Se la pressione di gonfiaggio troppo al-
ta, le asperit del terreno non vengono ammortizzate
e sono quindi trasmesse al manubrio, compromet-
tendo cos il comfort di marcia, e riducendo anche la
tenuta di strada in curva.
Se viceversa la pressione di gonfiaggio insufficien-
te, i fianchi dei pneumatici lavorano maggiormente, e
potrebbe verificarsi lo slittamento della gomma sul
cerchio oppure il suo distacco, con conseguente per-
dita di controllo del mezzo.In caso di frenate brusche,
inoltre, i pneumatici potrebbero fuoriuscire dai cer-
chi. Nelle curve, infine, il veicolo potrebbe sbandare.
Pressione di gonfiaggio
Anteriore: 180 kPa (1,8 bar)
Posteriore: 190 kPa (1,9 bar)
(a pieno carico 220 kPa (2,2 bar)
a
Dopo aver riparato un pneumatico, far esegui-
re l'equilibratura della ruota.
Controllare che le valvole di gonfiaggio siano
sempre munite dei tappini, onde evitare un improvvi-
so sgonfiaggio dei pneumatici. Le operazioni di so-
stituzione, riparazione, manutenzione ed equilibratu-
ra sono molto importanti, devono essere eseguite
con attrezzi appropriati e con la necessaria esperien-
za.
Se i pneumatici sono nuovi, possono essere ricoperti
di una patina scivolosa, guidare quindi con cautela
per i primi chilometri. Non ungere con liquido non
idoneo i pneumatici.
a
I pneumatici standard montati in questo vei-
colo sono:
anteriore 100/90-19 57H
posteriore 130/80-R17 65H.
La misura dei pneumatici indicata sul documento di
circolazione e qualsiasi difformit punibile a norma
di legge. Lutilizzo di pneumatici di misure diverse da
quelle indicate, potrebbe modificare lassetto del vei-
colo, compromettendone la maneggevolezza e la si-
curezza di guida. Utilizzare esclusivamente i pneuma-
tici scelti allorigine da aprilia.
Per ulteriori informazioni, vedi 7.4 (PNEUMATICI).
2 - 42
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
a
Check the surface of tyres and their wear in as
a
Controle el estado superficial y el desgaste, a faulty condition of the tyres compromises
ya que una mala condicin de los neumticos their grip as well as the manoeuvrability of the
compromete la adherencia al pavimento y la vehicle.
maniobrabilidad del vehculo. Change the tyre if worn or if an eventual puncture in
Substituya el neumtico si el mismo est gastado o the area of the tread is larger than 5 mm.
si hay un pinchazo ms ancho de 5 mm en la zona de
Limit of tread thickness
la banda de rodamiento.
Front: 2 mm
Lmite de la profundidad de la banda de rodamiento Rear: 2 mm
Delantera: 2 mm
Trasera: 2 mm
a a
Controle peridicamente la presin de inflado Periodically check the pressure of the tyres at
de los neumticos a la temperatura ambiente. room temperature. If the tyres are hot, the
La medicin ser incorrecta si los neumticos measurement is not correct.
estn calientes. Sobretodo, efecte la medicin lue- Measure pressure without fail after every long jour-
go de cada viaje largo. ney.
Si la presin de inflado es demasiado alta, las irregu- If the inflation pressure is too high, the bumps in the
laridades del terreno no sern amortiguadas y, por lo road/ground are not absorbed and are therefore
tanto, sern transmitidas al manillar, compromen- transmitted to the handlebar, compromising the com-
tiendo el confort de la marcha y reduciendo tambin fort of the drive as well as reducing roadholding in
la adherencia en curva. Si al contrario, la presin de curves.
inflado es insuficiente, los flancos del neumtico tra- If, contrarily, the inflation pressure is insufficient, the
bajarn ms, y la goma podra resbalar o salirse de la sides of the tyres are more exposed and may slip on
llanta, provocando la prdida de control del vehculo. the rim or even become detached from it, with the
Adems, en el caso de frenadas bruscas, los neum- consequent loss of control of the vehicle.
ticos podran salir de la llanta. Para concluir, en las In case of abrupt braking, the tyres can come away
curvas el vehculo podra derrapar. from the rims.
Moreover the vehicle may easily skid in curves.
Presin de inflado
Delantero: 180 kPa (1,8 bar) Inflation pressure
Trasero: 190 kPa (1,9 bar) Front: 180 kPa (1.8 bar)
(cargado totalmente 220 kPa (2,2 bar) Rear: 190 kPa (1.9 bar)
(at full load 220 kPa (2.2 bar)
a
Tras haber reparado un neumtico, haga equi-
a
librar la rueda. After repairing a tyre, have the wheel bal-
Controle que las vlvulas de inflado tengan anced.
los taponcitos para evitar que los neumticos se des- Make sure the tyres always have their valve
inflen improvisamente. Las substituciones, repara- sealing caps to prevent them from suddenly going
ciones, mantenimiento y equilibrado son muy impor- flat. The operations of changing, repairing, mainte-
tantes; deben realizarse con herramientas nance and balancing are very important and must be
adecuadas y con la experiencia necesaria. Si los neu- performed with the proper equipment and necessary
mticos son nuevos, pueden estar recubiertos con experience.
una pelcula resbaladiza, por lo tanto, conduzca con When tyres are new they may still be covered with a
cuidado durante los primeros kilmetros. No moje
slippery film therefore drive carefully for the first kilo-
los neumticos con lquidos no idneos.
metres. Do not oil tyres with unsuitable liquids.
a
Los neumticos estndar montados en este
a
vehculo son 100/90-19 57H (delantero) y This vehicle is equipped with standard tyres
130/80-R17 65H (trasero). 100/90-19 57H (front) and 130/80-R17 65H
La medida de los neumticos est indicada en la do- (rear). The size of the tyres is indicated in the
cumentacin del vehculo y cualquier diferencia pue- log-book and any dissimilarity is punishable by law.
de ser punible por la Ley. Using tyres with different dimensions may cause the
El empleo de neumticos con dimensiones diferen- instability of the vehicle, endangering its driving
tes puede causar la inestabilidad del vehculo, com- safety and manoeuvrability.
prometiendo la maniobrabilidad y la seguridad en la Use only tyres recommended by aprilia.
conduccin.
Utilice exclusivamente los neumticos escogidos ini- For further information see 7.4 (TYRES).
cialmente por aprilia.
Para ms informaciones, vase 7.4 (NEUMATICOS).
2 - 43
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
2.24 STERZO
a
Causa il peso e l'ingombro del veicolo, l'ope-
razione che segue richiede l'intervento di un
secondo operatore.
Procedere con cautela e assicurarsi di poter sostene-
re il peso del veicolo.
a
Al termine dell'operazione, accertarsi che la
rotazione del manubrio sia fluida, per evitare il
danneggiamento delle sedi di scorrimento e la
perdita di manovrabilit del veicolo.
2 - 44
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con mucha atencin 1.4 (PRECAUCIONES E IN- Read 1.4 carefully (PRECAUTIONS AND GENERAL
FORMACIONES GENERALES). INFORMATION).
Controle tras los primeros 1000 km (o 4 meses) y sucesi- Check after the first 1000 km (or 4 months) and then after
vamente, cada 6000 km (o 8 meses). every 6000 km (or 8 months).
Para una mejor maniobrabilidad, la direccin est equi- To ensure improved handling the steering is equipped
pada con cojinetes de rodadura. with rolling bearings.
Para una fcil rotacin del manillar y una conduccin se- The steering must be adjusted correctly to provide
gura, hay que ajustar correctamente la direccin. smooth rotation of the handlebar and safe driving.
Si la direccin es demasiado dura, obstaculiza la rotacin A tight steering hinders the smooth rotation of the handle-
fcil del manillar, mientras que si es demasiado blanda el bar whereas a slack steering implies inadequate stability.
vehculo tiene poca estabilidad.
a a
A causa del peso y del espacio que ocupa el Due to the weight and dimensions of the vehi-
vehculo la operacin que sigue a continua- cle, the following operation cannot be per-
cin necesita la intervencin de un segundo formed by one person only.
operador. Siga adelante con cuidado y compruebe si Proceed with care and make sure that you can sup-
puede soportar el peso del vehculo. port the weight of the vehicle.
Levante la parte delantera y coloque un soporte ade- Raise the front part of the vehicle and have a suitable
cuado (con altura 350 mm) por debajo del motor, de support (the weight of which should be about 350 mm)
manera que la rueda delantera tenga espacio suficien- placed under the engine, so that the front wheel can
te para moverse libremente y para evitar la cada del rotate freely and the vehicle cannot fall down.
vehculo. Keep the rear part of the vehicle down.
Mantenga bajada la parte trasera del vehculo. Shake the fork in the direction of travel (see figure).
Sacuda la horquilla en el sentido de marcha (vase fi- In case you find any slack, adjust the steering.
gura).
Ajuste en caso de que note un juego.
a
On completion of operation make sure that
a
Cuando haya finalizado la operacin, cerci- the rotation of the handlebar is smooth in or-
rese que la rotacin del manillar sea fluida, der to avoid damage to the balls and the loss
para evitar que las bolas se daen y que el ve- of manoeuvrability of the vehicle.
hculo pierda maniobrabilidad.
2 - 45
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
Per il controllo:
Rimuovere il paracoppa, vedi 7.1.9 (RIMOZIONE PA-
RACOPPA).
a
Causa il peso e l'ingombro del veicolo, l'ope-
razione che segue richiede l'intervento di un
secondo operatore.
Procedere con cautela e assicurarsi di poter sostene-
c
re il peso del veicolo.
Peso a vuoto del veicolo (in ordine di marcia):
200 kg.
Sollevare la parte anteriore e far sistemare un adegua-
to supporto (con altezza 350 mm) sotto il motore, in
modo tale che la ruota anteriore abbia libero spazio di
movimento e il veicolo sia assicurato contro la caduta.
Scuotere la ruota prima in senso verticale e poi tra-
sversalmente al senso di marcia (vedi figure).
Se si percepisce del gioco, procedere con la registra-
zione forcellone posteriore, vedi 2.26.1 (REGISTRA-
ZIONE FORCELLONE POSTERIORE).
Se il gioco persiste sostituire i cuscinetti, vedi 7.10
(SOSPENSIONE POSTERIORE).
2 - 46
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con mucha atencin 1.4 (PRECAUCIONES E IN- Read 1.4 carefully (PRECAUTIONS AND GENERAL
FORMACIONES GENERALES). INFORMATION).
Substituya el aceite horquilla delantera cada 12000 km (o Replace the front fork oil every 12000 km (or 16 months).
16 meses).
Should the fork reach the end of its stroke, check the oil
En caso de que note que la horquilla se hunde excesiva- level of the fork tubes, see 7.8.1 (CHECKING THE OIL
mente, es necesario controlar el nivel de aceite en las ba- LEVEL).
rras, vase 7.8.1 (CONTROL NIVEL ACEITE).
Make sure there are no oil leaks and that the outer sur-
Controle que la horquilla no tenga prdidas de aceite y face of the tubes is neither scratched nor grooved.
que la superficie exterior de las barras no estn rayadas If so, replace all the damaged parts.
o tengan ranuras.
En dicho caso, substituya todas las piezas daadas.
Lea con mucha atencin 1.4 (PRECAUCIONES E IN- Read 1.4 carefully (PRECAUTIONS AND GENERAL
FORMACIONES GENERALES). INFORMATION).
Controle peridicamente el juego de apriete del eje y de Periodically check the tightening of the pin and of the
los cojinetes de agujas de la horquilla trasera. needle bearings of the rear fork.
Para el control: To carry out this operation, proceed as follows:
Saque el protector de carter, vase 7.1.9 (DESMON- Remove the oil pan guard, see 7.1.9 (REMOVING
TAJE PROTECTOR DE CARTER). THE OIL PAN GUARD).
a a
A causa del peso y del espacio que ocupa el Due to the weight and dimensions of the vehi-
vehculo, la operacin que sigue a continua- cle, the following operation cannot be per-
cin necesita la intervencin de un segundo formed by one person only.
operador. Siga adelante con cuidado y compruebe si Proceed with care and make sure that you can sup-
c c
puede soportar el peso del vehculo. port the weight of the vehicle.
Peso en vaco del vehculo (en orden de mar- Weight of the vehicle without driver (ready for
cha): 200 kg. starting): 200 kg.
Levante la parte trasera del vehculo y coloque un so- Raise the rear part of the vehicle, have a suitable sup-
porte adecuado (con altura 350 mm) por debajo del port (the height of which should be 350 mm) placed
motor de manera que la rueda trasera tenga espacio under the engine, so that the rear wheel can rotate
suficiente para moverse libremente y para evitar la freely and the vehicle cannot fall down.
cada del vehculo. Shake the wheel vertically and trasversally to the di-
Sacuda la reda verticalmente y trasversalmente en el rection of travel (see figure).
sentido de marcha (vase figuras). If you find any slack, adjust the rear fork, see 2.26.1
En caso de que note un juego, ajuste el basculante, (ADJUSTING THE REAR FORK).
vase 2.26.1 (AJUSTE BASCULANTE). If the slack persists, adjust the bearings, see 7.10
Si el juego contina, sustituya los cojinetes, vase (REAR SUSPENSION).
7.10 (SUSPENSION TRASERA).
2 - 47
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
La ghiera di regolazione non deve essere avvi-
tata per pi di 12 mm dallinizio della filettatu-
ra (vedi figura). Se tale misura viene superata,
durante la guida si avranno degli improvvisi sbalzi
alla minima asperit del terreno e ogni intervento sul-
la vite (3) sar inutile.
Svitare moderatamente la ghiera di bloccaggio (2).
Utilizzando lapposita chiave, agire sulla ghiera di re-
golazione (1) (regolazione precarica molla ammortiz-
zatore) (vedi tabella).
Eventualmente intervenire sulla vite (3) (regolazione
frenatura idraulica in estensione ammortizzatore) (vedi
tabella).
Ottenute le condizioni ottimali di assetto serrare com-
pletamente la ghiera di bloccaggio (2).
a
Tramite la vite (3), provvedere alla regolazione
della frenatura idraulica in estensione dellam-
mortizzatore in base alle condizioni duso del
veicolo. 1
a
Se lassetto del veicolo impostato per guida a
pieno carico, sconsigliato ruotare la vite (3)
verso sinistra (senso antiorario), per evitare MAX
improvvisi sbalzi durante la guida. 2 12 mm
GHIERA DI REGOLAZIONE (1)
Avvitandola Svitandola
Funzione Aumento della Diminuzione della
precarica molla precarica molla
Tipo di assetto Pi rigido Pi morbido
Tipo di strade Normali - regolari Con fondo
consigliate sconnesso
Note Guida con Guida senza
passeggero ed passeggero
eventuale bagaglio
c
eventuale bagaglio
Dalla regolazione di assetto pi rigido a quello
pi morbido sono possibili varie posizioni in-
termedie.
2 - 48
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
a a
No hay que enroscar nunca la tuerca de regu- The adjusting ring must not be screwed for
lacin por ms de 12 mm desde el inicio de la more than 12 mm from the beginning of the
rosca (vase figura). En caso de que se supe- thread (see figure). If this length is exceeded,
re esta medida, durante la marcha pueden darse even the slightest uneveness of the ground may
unos rebotes al encontrar las irregularidades, aun- cause sudden jerks during the drive, and any adjust-
que pequeas, del suelo y cada intervencin sobre el ment of the screw (3) will be useless.
tornillo (3) resultar intil. Slightly unscrew the locking ring (2).
Destornille moderadamente la tuerca de bloqueo (2). By means of the apposite spanner, adjust the ring (1)
Utilizando la llave correspondiente, acte sobre la (shock absorber spring preload adjustment) (see ta-
tuerca de regulacin (1) (regulacin precarga muelle ble).
amortiguador) (vase tabla). If necessary, adjust the screw (3) (adjusting the hy-
Eventualmente intervenga en el tornillo (3) (regulacin draulic braking with extended shock absorber) (see ta-
frenado hidrulico en extensin amortiguador) (vase ble).
tabla). Once the optimal attitude has been reached, tighten
Una vez que haya alcanzado las condiciones ptimas the locking ring (2) completely.
de ajuste, apriete del todo la tuerca de bloqueo (2).
a a
Segn las condiciones de uso del vehculo, By means of the screw (3), adjust the hydraulic
regule el frenado hidrulico en extensin del braking with extended shock absrober accord-
amortiguador actuando sobre el tornillo (3). ing to the conditions of use of the vehicle.
a a
Si el vehculo ha sido ajustado para una con- If the vehicle attitude has been set for full
duccin con carga mxima, se desaconseja load, do not turn the screw (3) to the left (anti-
girar el tornillo (3) hacia la izquierda (sentido clockwise), in order to avoid sudden jerks
antihorario) para evitar rebotes imprevistos durante while riding.
la conduccin.
TUERCA DE REGULACIN (1) ADJUSTING RING (1)
Atornillndola Destornillndola By screwing it By unscrewing it
Funcin Aumento de la Disminucin de la Function Spring preload Spring preload
precarga muelle precarga muelle increase decrease
Tipo de ajuste Ms rgido Ms suave Attitude Harder Softer
Tipo de carreteras Normales - Con firme irregular Recommended Normal - regular Raveled road
aconsejadas regulares kind of road road surface surface
Notas Conduccin con Conduccin sin Notes Rider, passenger Solo rider
pasajero y eventual pasajero and luggage,
equipaje if any
2 - 49
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Registrare il precarico della molla e della frena-
tura idraulica in estensione dellammortizzato- 2
re in base alle condizioni duso del veicolo.
Aumentando il precarico della molla, necessario
aumentare anche la frenatura idraulica in estensione
dellammortizzatore, per evitare improvvisi sbalzi du-
rante la guida.
Tipo di strade Normali - regolari Con fondo Tipo di assetto Pi rigido Pi morbido
consigliate sconnesso Tipo di strade Con fondo Normali - regolari
Note Guida con Guida senza consigliate sconnesso
passeggero ed passeggero Note Guida con Guida senza
eventuale bagaglio passeggero ed passeggero
c
eventuale bagaglio
Dalla regolazione di assetto pi rigido a quello
pi morbido sono possibili varie posizioni in-
termedie.
2 - 50
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
2.27.2 AJUSTE SUSPENSION TRASERA CON 2.27.2 ADJUSTING THE REAR SUSPENSION WITH
REGULACION HIDRAULICA DE PRECARGA & PRELOAD HYDRAULIC ADJUSTMENT &
Gire el volante (1) (regulacin precarga muelle amorti- Rotate the flywheel (1) (shock absorber spring preload
guador) en un sentido o en el otro alcanzado, de tal for- adjustment) in one sense or the other, in order to ob-
ma, las condiciones ptimas de ajuste (vase tabla). tain the optimal attitude (see table).
Eventualmente acte sobre el tornillo (2) (regulacin fre- If necessary, adjust the screw (2) (hydraulic braking
nado hidrulico en extensin amortiguador) (vase ta- adjustment with extended shock absorber) (see table).
bla).
a
Adjust the preload of the spring and of the hy-
a
Segn las condiciones de uso del vehculo, draulic braking with extended shock absorber
regule la precarga del muelle y del frenado hi- according to the conditions of use of the vehi-
drulico en extensin del amortiguador. cle. When the spring preload is increased, it is neces-
Aumentando la precarga del muelle, es necesario au- sary to increase also the hydraulic braking with ex-
mentar incluso el frenado hidrulico en extensin del tended shock absorber, in order to avoid sudden
amortiguador para evitar rebotes imprevistos duran- jerks while riding.
te la conduccin.
ADJUSTING FLYWHEEL (1)
VOLANTE DE REGULACIN (1) Rotation to the
Rotacin hacia la Rotacin hacia la Rotation to the
left
derecha (sentido izquierda (senti- right (clockwise)
(anticlockwise)
horario) do antihorario)
Function Preload increase Preload decrease
Funcin Aumento de la Disminucin de la
precarga precarga Attitude Harder Softer
Tipo de ajuste Ms rgido Ms suave Recommended Normal - regular Raveled road
Tipo de carreteras Normales - Con firme irregular kind of road road surface surface
aconsejadas regulares Notes Rider, passenger Solo rider
Notas Conduccin con Conduccin sin and luggage, if any
pasajero y eventual pasajero
equipaje
ADJUSTING SCREW (2)
TORNILLO DE REGULACIN (2) Rotation to the
Rotation to the
left
Rotacin hacia la Rotacin hacia la right (clockwise)
(anticlockwise)
derecha (sentido izquierda (sentido
horario) antihorario) Function Increased braking Decreased braking
Funcin Aumento del Disminucin del with extended with extended
frenado en frenado en shock absorber shock absorber
extensin extensin Attitude Harder Softer
Tipo de ajuste Ms rgido Ms suave Recommended Raveled road Normal - regular
Tipo de carreteras Con firme irregular Normales - kind of road surface road surface
aconsejadas regulares
Notes Rider, passenger Solo rider
Notas Conduccin con Conduccin sin and luggage, if any
pasajero y eventual pasajero
c
equipaje
c
Various intermediate positions are possible
Entre el ajuste ms rgido y el ms suave hay between the hard and soft attitude.
varias posiciones intermedias.
2 - 51
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO
a
Causa il peso e l'ingombro del veicolo, l'ope-
razione che segue richiede l'intervento di un
secondo operatore.
Procedere con cautela e assicurarsi di poter sostene-
re il peso del veicolo.
a
Causa il peso e l'ingombro del veicolo, l'ope-
razione che segue richiede l'intervento di un
secondo operatore.
Procedere con cautela e assicurarsi di poter sostene-
re il peso del veicolo.
2 - 52
OPERACIONES DE MANTENIMIENTO PERIDICO Y DE PERIODIC SERVICE AND SETTING UP OPERATIONS
PUESTA A PUNTO
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
Controle cada 6000 km (u 8 meses). Check the front wheel every 6000 km (or 8 months).
Desmonte el protector de crter 7.1.9 (DESMONTA- Remove the oil pan guard, see 7.1.9 (REMOVING
JE PROTECTOR DE CARTER). THE OIL PAN GUARD).
a a
A causa del peso y del espacio que ocupa el Due to the weight and dimensions of the vehi-
vehculo la operacin que sigue a continua- cle, the following operation cannot be per-
cin necesita la intervencin de un segundo formed by one person only.
operador. Proceed with care and make sure that you can sup-
Siga adelante con cuidado y compruebe si puede so- port the weight of the vehicle.
portar el peso del vehculo.
Levante la parte delantera y coloque un soporte ade- Raise the front part of the vehicle and have a suitable
cuado (con altura 350 mm) por debajo del motor, de support (the height of which should be about 350 mm)
manera que la rueda delantera tenga espacio suficien- placed under the engine, so that the front wheel can
te para moverse libremente y para evitar la cada del rotate freely and the vehicle cannot fall down.
vehculo. Keep down the rear part of the vehicle.
Mantenga bajada la parte trasera del vehculo. Make the wheel rotate in one sense or the other man-
Gire manualmente la rueda en ambos sentidos. ually.
Compruebe que la rueda gire regularmente y sin obs- Make sure that the wheel rotation is regular and that
tculos y/o sin ruido, en caso contrario sustituya los there are no obstacles or noise, otherwise change the
cojinetes, vase 7.2.2 (SUSTITUCION COJINETES). bearings, see 7.2.2 (CHANGING THE BEARINGS).
Si al girar la rueda sta oscila, controle los componen- If during the rotation of the wheel any oscillation should
tes correspondientes, vase 7.2.3 (CONTROL). be noticed, check the involved components, see
7.2.3 (CHECKING).
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
Controle cada 6000 km (u 8 meses). Check the rear wheel every 6000 km (or 8 months).
Desmonte el protector de crter 7.1.9 (DESMONTA- Remove the oil pan guard, see 7.1.9 (REMOVING
JE PROTECTOR DE CARTER). THE OIL PAN GUARD).
a a
A causa del peso y del espacio que ocupa el Due to the weight and dimensions of the vehi-
vehculo la operacin que sigue a continua- cle, the following operation cannot be per-
cin necesita la intervencin de un segundo formed by one person only.
operador. Proceed with care and make sure that you can sup-
Siga adelante con cuidado y compruebe si puede so- port the weight of the vehicle.
portar el peso del vehculo.
Levante la parte trasera del vehculo y coloque un so- Raise the front part of the vehicle and have a suitable
porte adecuado (con altura 350 mm) por debajo del support (the height of which should be about 350 mm)
motor, de manera que la rueda trasera tenga espacio placed under the engine, so that the front wheel can
suficiente para moverse libremente y para evitar la rotate freely and the vehicle cannot fall down.
cada del vehculo. Make the wheel rotate in one sense or the other man-
Gire manualmente la rueda en ambos sentidos. ually.
Compruebe que la rueda gire regularmente y sin obs- Make sure that the wheel rotation is regular and that
tculos y/o sin ruido, en caso contrario sustituya los there are no obstacles or noise, otherwise change the
cojinetes, vase 7.3.2 (SUSTITUCION COJINETES). bearings, see 7.3.2 (CHANGING THE BEARINGS).
Si al girar la rueda sta oscila, controle los componen- If during the rotation of the wheel any oscillation should
tes correspondientes, vase 7.3.3 (CONTROL). be noticed, check the involved components, see
7.3.3 (CHECKING).
2 - 53
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO / OPERACIONES DE MANTENIMIENTO PERIDICO
Y DE PUESTA A PUNTO / PERIODIC SERVICE AND SETTING UP OPERATIONS
2.30 SERRAGGIO VITI E DADI 2.30 APRIETE DE LOS 2.30 TIGHTENING SCREWS
TORNILLOS Y TUERCAS AND NUTS
Serrare dopo i primi 1000 km (o 4
mesi) e successivamente ogni 6000 Apriete tras los primeros 1000 km (o Tighten after the first 1000 km (or 4
km (o 8 mesi). 4 meses) y sucesivamente, cada months) and then every 6000 km (or
6000 km (o 8 meses). 8 months)
a
Le viti e i dadi riportati nella
a a
Los tornillos y las tuercas The screws and nuts indi-
tabella, appartengono a
indicados en la tabla perte- cated in the table are part
componenti importanti per
necen a componentes im- of components important
la sicurezza. portantes para la seguridad. for safety.
In caso di necessit serrarli alla En caso de necesidad, apritelos In case of necessity, tighten to the
coppia prescritta, utilizzando una con el par indicado, utilizando una prescribed torque, using a dy-
chiave dinamometrica. llave dinamomtrica. namometric spanner.
Coppie di serraggio viti e dadi del telaio
Par de apriete de los tornillos y tuercas del bastidor
Frame screws and nuts driving torques
Componente / Componente / Component Nm kgm
Dado della testa dello sterzo
Tuerca de la cabeza de la direccin 100 10
Steering head nuts
Viti superiori fissaggio manubrio
Tornillos superior de sujecin manillar 25 2,5
Upper handlebar fastening screw
Viti / dadi inferiori fissaggio manubrio
Tornillos/tuercas inferior de sujecin manillar 30 3
Lower handlebar fastening screw and nuts
Viti piastra superiore e inferiore forcella
Tornillos placa superior y inferior horquilla 50 5
Upper and lower fork plate screws
Tappi steli forcella anteriore
Tapones barras horquilla delantera 20 2
Front fork tube caps
Vite inferiore portaruota forcella (montare con LOCTITE 270)
Tornillo inferior portarrueda horquilla (monte con LOCTITE 270) 50 5
Fork slider lower screw (assemble with LOCTITE 270)
Perno ruota anteriore
Eje de la rueda delantera 80 8
Front wheel pin
Viti bloccaggio perno ruota anteriore
Tornillos de sujecin del eje de la rueda delantera 12 1,2
Front wheel pin loocking screws
Viti fissaggio pompa freno anteriore
Tornillos de sujecin bomba freno delanter o 12 1,2
Front brake pump fastening screws
Viti fissaggio pinza freno anteriore
Tornillos de sujecin pinza freno delantera 50 5
Front brake caliper fastening screws
Vite raccordo tubazione pinza freno anteriore
Tornillo unin tubera pinza freno delantero 15 1,5
Front brake caliper pipe fitting screw
Valvola di spurgo freno anteriore e posteriore
Vlvula de purga freno delantero y trasero 15 1,5
Front and rear brake bleeder
Viti fissaggio disco freno (ant. e post.) (montare con LOCTITE frena filetti medio)
Tornillos de sujecin disco freno (delant. y tras.) (coloque LOCTITE en la rosca) 12 1,2
Front and rear brake disc fastening screws (assemble with thread-locking LOCTITE medium)
Bussola registrazione forcellone posteriore Contatto + 1/4 di giro
Brjula de regulacin basculante Contacto + 1/4 de vuelta
Rear fork adjusting bush Contact + one fourth turn
Ghiera di bloccaggio perno forcellone posteriore
Tuerca de bloqueo eje basculante 40 4
Rear fork pin adjusting ring
Perno forcellone posteriore
Eje basculante 100 10
Rear fork pin
Viti interne di fissaggio supporto superiore ammortizzatore posteriore
Tornillos de fijacin interiores soporte superior amortiguador trasero 25 2,5
Inner fastening screws of the rear shock absorber upper support
Viti esterne di fissaggio supporto superiore ammortizzatore posteriore
Tornillos de fijacin exteriores soporte superior amortiguador trasero 80 8
Outer fastening screws of the rear shock absorber upper support
Vite/dado fissaggio superiore ammortizzatore posteriore
Tornillo/tuerca de fijacin parte superior amortiguador trasero 50 5
Fastening screw/nut of the rear shock absorber upper part
Vite/dado fissaggio inferiore ammortizzatore posteriore
Tornillo/tuerca de fijacin parte inferior amortiguador trasero 35 3,5
Fastening screw/nut of the rear shock absorber lower part
Viti/dadi fissaggio biella singola sospensione posteriore
Tornillo/tuerca de fijacin una sola palanca de conexin suspensin trasera 80 8
Fastening screws/nuts of the rear shock absorber single connecting rod
2 - 54
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO / OPERACIONES DE MANTENIMIENTO PERIDICO
Y DE PUESTA A PUNTO / PERIODIC SERVICE AND SETTING UP OPERATIONS
2 - 55
OPERAZIONI DI MANUTENZIONE PERIODICA E DI MESSA A PUNTO / OPERACIONES DE MANTENIMIENTO PERIDICO
Y DE PUESTA A PUNTO / PERIODIC SERVICE AND SETTING UP OPERATIONS
2 - 56
1
2
MOTORE
3
MOTOR
ENGINE
4
3 -1
MOTORE
INDICE GENERAL
MOTORE 3
INDICE
3 -2
MOTOR ENGINE
MOTOR 3 ENGINE 3
3 -3
MOTORE
LATO DESTRO
LATO SUPERIORE
Carter protezione pignone trasmissione, vedi 3.1.3
Carburatore, vedi 4.5.3 (RIMOZIONE CARBURATO- (RIMOZIONE CARTER PROTEZIONE PIGNONE
RI). TRASMISSIONE)
Coperchio punterie (1). Pignone trasmissione.
Sensore pressione olio motore (2). Coperchio volano (8).
Termistore temperatura liquido refrigerante, vedi
5.5 (RIMOZIONE TERMISTORE LIQUIDO REFRI-
LATO ANTERIORE E DESTRO GERANTE).
c
Sensore cambio in folle.
Tubi di scarico, vedi 3.1.1 (RIMOZIONE TUBI DI
SCARICO) Per alcuni componenti le procedure di smon-
taggio e rimontaggio sono riportate nelle pa-
gine di questo capitolo, per gli altri componenti fare
riferimento al MANUALE DOFFICINA MOTORE,
N933 (D-UK) / N 934 (I-E-F).
3 -4
MOTOR ENGINE
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
Las partes indicadas a continuacin pueden desmontar- The parts listed below can be disassembled and reas-
se y reinstalarse sin tener que sacar el motor del basti- sembled without removing the engine from the frame.
dor.
c
Sensor cambio en punto muerto.
c
For certain components the procedures of
Para algunos componentes los procedimien- disassembling and reassembling are indicat-
tos de desmontaje y de reinstalacin estn in- ed in this chapter, for the other components please
dicados en las pginas de este captulo, para los refer to the ENGINE SERVICE MANUAL, n. 933 (D-
otros componentes refirase al MANUAL DE TALLER UK)/ n. 934 (I-E-F).
DEL MOTOR, N 933 (D-UK) / N 934 (I-E-F).
3 -5
MOTORE
3 -6
MOTOR ENGINE
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
Desmonte el panel lateral derecho, vase Remove the right side, see 7.1.4 (REMOVING THE
7.1.4 (DESMONTAJE PANELES LATERALES DE- RIGHT AND LEFT SIDES).
RECHO E IZQUIERDO). Remove the radiator, see 5.2 (REMOVING THE RA-
Saque el radiador, vase 5.2 (DESMONTAJE RADIA- DIATOR).
DOR). Unscrew and remove the two screws (1-2).
Destornille y quite los dos tornillos (1-2). Remove the radiator support (3).
Desmonte el soporte radiador (3). Unscrew and remove the two screws (4-5), taking the
Destornille y quite los dos tornillos (4-5) guardando las washers.
arandelas. Remove the guard (6).
Desmonte el elemento de proteccin (6). Loosen the two screws (7-8) on the clamps (9-10).
Destornille dando pocas vueltas a los dos tornillos (7- Unscrew and remove the two nuts (11) that fasten the
8) sobre las abrazaderas (9-10). exhaust pipe flange to the cylinder.
Destornille y quite las dos tuercas (11) que sujetan la
Nut (11) driving torque: 25 Nm (2.5 kgm).
brida del tubo de escape al cilindro.
Move the exhaust pipe unit (12) forward as much as
Par de apriete tuercas (11): 25 Nm (2,5 kgm)
necessary to withdraw them from the seats on the cyl-
Desplace hacia adelante el grupo tubos de escape inder.
c
(12) lo suficiente para extraerlos de sus sedes sobre el
cilindro. To facilitate the withdrawing of the exhaust
c
pipe unit (12), strike slightly (by means of a
Para que la extraccin del grupo tubos de es- rubber hammer) one of the two supports of the guard
cape (12) resulte ms fcil, golpee moderada- (see figure).
mente (utilizando un martillo de goma) sobre uno de
los dos soportes elemento de proteccin (vase figu- Loosen the screw (13) on the clamp (14).
ra). Withdraw the pipe (15) from the exhaust pipe unit (12).
If the graphite sealing ring (16) is broken or worn,
Destornille dando pocas vueltas al tornillo (13) sobre change it.
la abrazadera (14). Remove the exhaust pipe unit (12) by withdrawing it
Extraiga el tubo (15) del grupo tubos de escape (12). from the front part.
c
Si ljunta de grafito (16) resulta desgastado, sustitya-
lo. Shift the exhaust pipe unit (12) with small
Desmonte el grupo tubos de escape (12) extrayndolo movements, trying to find the right position to
desde la parte delantera. withdraw it (lift the front part, lower the rear part giv-
c
ing the whole unit a forward screwing movement; the
Desplace el grupo tubos de escape (12) con rear lower part must pass through the turns of the
pequeos movimientos, buscando la combi- rear shock absorber spring) (see figure).
nacin mejor para su extraccin (levante la parte de-
a
lantera, baje la parte trasera de manera que todo rea- Plug the engine exhaust openings, in order to
lice un movimiento de enrosque hacia adelante; la avoid any accidental introduction of foreign
parte inferior trasera ha de pasar entre las dos espi- matters.
ras del muelle amortiguador trasero) (vase figura).
3 -7
MOTORE
a
Prima di rimuovere il pedale comando cambio
contrassegnare pedale e pignone (vedi figura)
per posizionarlo correttamente nel rimontag-
gio.
a
Prima di procedere con le operazioni che se-
guono considerare che il motore deve essere
rimosso dal lato sinistro del veicolo; provve-
dere quindi a posizionare le attrezzature necessarie.
3 -8
MOTOR ENGINE
3.1.2 DESMONTAJE PEDAL MANDO CAMBIO 3.1.2 REMOVING THE GEARSHIFT FOOT LEVER
a a
Antes de desmontar el pedal del mando del Before removing the gearshift foot lever, mark
cambio marque el pedal y el pin (vase fi- foot lever and pinion (see figure), in order to
gura) para colocarlo correctamente durante be able to reassemble them correctly.
su instalacin.
Position the vehicle on the stand.
Coloque el vehculo sobre el caballete. Loosen the screw (1).
Afloje el tornillo (1). Withdraw the gearshift foot lever (2).
Extraiga el pedal del mando del cambio (2).
3.1.3 DESMONTAJE CARTER PROTECCION PION 3.1.3 REMOVING THE TRANSMISSION PINION
TRANSMISION PROTECTION CASE
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
3.2 EXTRACCION DEL MOTOR DEL BASTIDOR 3.2 REMOVING THE ENGINE FROM THE
FRAME
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA-
CIONES GENERALES). Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
TION) carefully.
a
Antes de seguir adelante con las operaciones
a
que siguen, recuerde que hay que sacar el Before performing the operations described
motor desde el lado izquierdo del vehculo; below, consider that the engine must be re-
por lo tanto prepare los equipos necesarios. moved from the left side of the vehicle; there-
fore, provide for positioning the necessary equip-
Coloque el vehculo sobre el caballete central & o ment correctly.
sobre un adecuado caballete de soporte fijado en los
pivotes del caballete central. Position the vehicle on the centre stand & , or on an
Desconecte segn este orden el cable negativo () y apposite support stand fixed to the couplings of the
luego el positivo (+) de la batera. centre stand.
Disconnect first the negative cable () and then the
a
positive cable (+) from the battery.
Durante la instalacin, conecte antes el cable
a
positivo (+) y luego el negativo ().
Upon reassembly, connect first the positive
(+) and then the negative () cable.
3 -9
MOTORE
a
Per pulire le parti esterne del motore, utilizza-
re detergente sgrassante, pennelli e stracci.
Parti in gomma e plastica non devono essere
danneggiate da detergenti e solventi corrosivi o pe-
netranti.
a
Apporre dei contrassegni su cavi, manicotti,
tubi ecc. per evitare lo scambio nel rimontag-
gio.
3 - 10
MOTOR ENGINE
a a
Para limpiar las partes exteriores del motor, To clean the outer parts of the engine, use a
utilice detergente desengrasante, pinceles y degreaser, brushes and cloths.
trapos. Do not use corrosive detergents and solvents
Detergentes y disolventes corrosivos o penetrantes or penetrants, in order to avoid damaging the rubber
pueden daar las partes de goma y de plstico. and plastic parts.
En caso de que use una maquina limpiadora de va- If it is necessary to use a steam cleaning machine, do
por, no dirija chorros de agua o de aire a alta presin not direct high pressure water or air jets towards the
o chorros de vapor sobre las siguientes partes: cubos following parts: wheel hubs, controls on the right and
de las ruedas, mandos colocados en el lado derecho left side of the handlebar, brake pumps, instruments
e izquierdo del manillar, bombas de los frenos, instru- and indicators, silencer outlets, glove compartment,
mentos e indicadores, salidas de los silenciadores, ignition switch/steering lock, electrical components.
vano portadocumentos, interruptor de encendido/se-
guro de direccin, componentes elctricos. Clean the engine thoroughly.
Drain the engine oil completely, see
Limpie con cuidado el motor. 2.13 (CHANGING ENGINE OIL AND OIL FILTER).
Descargue del todo el aceite motor, vase Remove the exhaust pipes, see 3.1.1 (REMOVING
2.13 (CAMBIO DEL ACEITE MOTOR Y DEL FILTRO THE EXHAUST PIPES).
DEL ACEITE DEL MOTOR). Remove the expansion tank, see 5.6 (REMOVING
Desmonte los tubos de escape, vase THE EXPANSION TANK).
3.1.1 (DESMONTAJE TUBOS DE ESCAPE). Remove the carburettors, see 4.5.3 (REMOVING
Desmonte el depsito de expansin, vase THE CARBURETTORS).
5.6 (DESMONTAJE DEPOSITO DE EXPANSION). Remove the gearshift foot lever, see
Desmonte los carburadores, vase 3.1.2 (REMOVING THE GEARSHIFT FOOT LEVER).
4.5.3 (DESMONTAJE CARBURADORES). Disconnect the clutch cable (1) from the lever (2).
Desmonte el pedal mando cambio, vase
a
3.1.2 (DESMONTAJE PEDAL MANDO CAMBIO). Mark the cables, couplings, pipes, etc., in or-
Desconecte el cable embrague (1) de la palanca (2). der to avoid confusing them during the reas-
sembly.
Lift the protection element (3), unscrew and remove
the nut (4) and disconnect the starter cable (5).
Unscrew and remove the screw (6), disconnecting the
Levante el elemento de proteccin (3), destornille y earth cable (7).
quite la tuerca (4) y desconecte el cable motor de Remove the transmission pinion protection case, see
arranque (5). 3.1.3 (REMOVING THE TRANSMISSION PINION
Destornille y quite el tornillo (6) desconectando el ca- PROTECTION CASE).
ble de masa (7). Remove the stop ring (8).
Desmonte el crter proteccin pin transmisin, va- Withdraw the transmission pinion (9) complete with
se 3.1.3 (DESMONTAJE CARTER PROTECCION chain from the shaft.
c
PION TRANSMISION).
Quite el anillo de seguridad (8). If the withdrawing of the transmission pinion
Extraiga del eje el pin transmisin (9) completo de (9) results difficult, slacken the chain slightly,
cadena. see 2.16.3 (ADJUSTMENT).
c En caso de que la operacin de extraccin pi- Remove the transmission pinion (9).
c
n transmisin (9) resulte difcil, afloje algo
la tensin de la cadena, vase 2.16.3 (AJUSTE). Upon reassembly, apply LOCTITE Anti-Seize
on the inner toothing of the transmission pi-
Desmonte el pin transmisin (9). nion (9).
3 - 11
MOTORE
a
Liberare tutti i cavi dalle relative fascette di
fissaggio situate lungo il percorso.
Premunirsi poi di altrettante fascette da utiliz-
zare nel rimontaggio.
c
Sfilare il tubo sfiato olio (27) (sul carter volano).
Liberare il tubo dallaggancio (28) sulla culla.
c
a motore).
Liberare il tubo dallaggancio (31).
a
Liberare tutti i tubi dalle relative fascette di fis-
saggio situate lungo il percorso.
Premunirsi poi di altrettante fascette da utiliz-
zare nel rimontaggio.
3 - 12
MOTOR ENGINE
Destornille el tornillo (17) desconectando el cable del Unscrew the screw (17), disconnecting the neutral
interruptor cambio en punto muerto (18). gear switch cable (18).
Desconecte el conector del alternador (19) y del pick- Disconnect the connector of the alternator (19) and of
up (20) (lado izquierdo del vehculo). the pick-up (20) (left side of the vehicle).
a a
Suelte todos los cables de sus correspon- Release all the cables from the fastening
dientes abrazaderas de bloqueo. clamps positioned along them. Get other
Luego, prepare el mismo nmero de abraza- clamps to be used for the reassembly.
c
deras para utilizarlas durante la instalacin.
c
Get screwdriver-type pipe clamps, to replace
Prepare unas abrazaderas de destornillador the original ones (special type without screw).
que hay que sustituir a las originales (de tipo
especial sin tornillo). Cut the heads of the pipe clamps in the following order
(21-22-23-24-25-26).
Corte siguiendo este orden la cabeza de las abrazade- Withdraw the oil breather pipe (27) (on the flywheel
ras (21-22-23-24-25-26). guard).
c
Extraiga el tubo de purga aceite (27) (sobre el crter
c
volante). Release the pipe from the connection (28) on
the cradle.
Suelte el tubo del enganche (28) sobre la cu-
na.
Withdraw the engine oil pipe (29) from the engine
Extraiga el tubo aceite motor (29) del motor (de motor (from engine to tank).
a depsito). Withdraw the engine oil pipe (30) from the engine
Extraiga el tubo aceite motor (30) del motor (de dep- (from tank to engine).
c c
sito a motor).
Release the pipe from the connection (31).
Suelte el tubo del enganche (31).
Withdraw the coolant coupling (32) (to the pump).
Extraiga el manguito lquido refrigerante (32) (en en-
Withdraw the coolant coupling (33) (from the engine).
trada a la bomba).
Withdraw the engine oil breather pipe (34) (on the tap-
Extraiga el manguito lquido refrigerante (33) (en sali-
pet cover).
da del motor).
Extraiga el tubo de purga aceite motor (34) (sobre la
a
Release all the cables from the fastening
tapa empujavlvulas).
clamps positioned along them. Get other
clamps to be used for the reassembly.
a
Suelte todos los tubos de sus correspondien-
tes abrazaderas de bloqueo.
a
Plug all the engine openings, pipes and pipe
Sucesivamente, prepare el mismo nmero de
couplings, in order to avoid any accidental in-
abrazaderas para utilizarlas durante la instalacin.
troduction of foreign matters.
a
Tape las aberturas del motor, los tubos y los
manguitos, impidiendo la entrada de cuerpos
extraos.
3 - 13
MOTORE
a
Le fasce e il paranco devono essere adeguati
a sostenere in tutta sicurezza il motore che
pesa circa 50 kg.
3 - 14
MOTOR ENGINE
Suspenda el motor segn lo indicado en la figura y en- Sling the engine as indicated in the figure and hook the
ganche las fajas (hacindolas pasar por el lado iz- bands (passing them on the left side of the frame) to a
quierdo del bastidor) en un aparejo para sujetarlo. hoist for support.
a a
Las fajas y el aparejo deben resultar adecua- The bands and the hoist must be suitable for
dos para soportar con la mayor seguridad el bearing the weight of the engine, which is
motor que pesa unos 50 kg. about 50 kg, in total safety.
Destornille y quite las dos tuercas (35-36) y extraiga Unscrew and remove the two nuts (35-36) and with-
los dos tornillos (37-38) de fijacin bastidor/cuna parte draw the two screws (37-38) that fasten the frame to
delantera. the front part of the cradle.
Par de apriete tuercas/tornillos (35-36/37-38): Nut/screw (35-36/37-38) driving torque:
50 Nm (5 kgm). 50 Nm (5 kgm).
Guarde la placa que contiene los tubos (39). Take the pipe covering plate (39).
Destornille y quite las dos tuercas (40-41) y extraiga Unscrew and remove the two nuts (40-41) and with-
los dos tornillos (42-43) de fijacin motor/cuna. draw the two screws (42-43) that fasten the engine to
the cradle.
Par de apriete tuercas/tornillos (40-41/42-43):
50 Nm (5 kgm). Nut/screw (40-41/42-43) driving torque:
50 Nm (5 kgm).
3 - 15
MOTORE
c
in avanti.
Nel rimontaggio della culla (46) posizionare al
suo interno il tubo di compensazione liquido
c
refrigerante e il tubo olio motore (29).
NOTA (X)
Da questo punto in poi, nella reinstallazione mo-
tore sul telaio, procedere con le specifiche procedure,
vedi 3.3 (REINSTALLAZIONE MOTORE SUL TELAIO).
a
Il perno forcellone posteriore (48) non deve
essere sfilato completamente ma deve essere
lasciato infilato quanto basta a mantenere
laccoppiamento telaio/forcellone sul lato destro, evi-
tando in questo modo che tutto il gruppo ruota poste-
riore/forcellone si sposti verso il basso andando fuo-
ri allineamento.
Leventuale successiva operazione di rimontaggio ri-
sulterebbe particolarmente difficoltosa.
Svitare completamente il perno (48).
Infilare sulla bussola di registrazione (47) lapposito at-
trezzo, vedi 1.8 (ATTREZZI SPECIALI).
Utilizzando un martello in gomma, battere con piccoli
colpi sullattrezzo sino a portarlo a fine corsa sulla bus-
sola di registrazione (47).
a
Causa il peso (circa 50 kg) e lingombro del
motore, le operazioni che seguono richiedono
lintervento di un secondo operatore. Accer-
tarsi preventivamente sulle procedure di esecuzione.
Loperazione di rimozione deve essere svolta con la
massima attenzione.
Svitare e togliere il dado (50) e sfilare la vite inferiore
posteriore (51) di fissaggio motore/telaio.
a
Dopo avere sfilato la vite (51) il motore tende-
r a ruotare leggermente in avanti (con fulcro
c
sulla vite 53).
Per agevolare lo sfilamento della vite (51) sol-
levare leggermente il motore.
Svitare e togliere il dado (52) e sfilare la vite superiore
(53) di fissaggio motore/telaio, recuperando la rondel-
la.
a
Il motore ora completamente libero e non ha
pi alcun fissaggio. Manovrare con cautela,
attenzione alle dita e agli arti.
Afferrare il motore dal lato destro e dal lato sinistro,
in punti dove la presa risulti pi sicura ed estrarlo dal
lato sinistro con piccoli spostamenti, ricercando la
combinazione di movimenti pi efficace.
Appoggiarlo al suolo su superficie pulita e provvede-
re affinch rimanga in posizione con dei blocchetti di
legno.
3 - 16
MOTOR ENGINE
Destornille y saque la tuerca (44) y extraiga el tor- Unscrew and remove the nut (44) and withdraw the
nillo (45) de fijacin bastidor/cuna parte trasera. screw (45) that fastens the frame to the rear part of the
Par de apriete tuercas/tornillos (44-45): cradle.
50 Nm (5 kgm). Nut/screw (44-45) driving torque:
Saque la cuna (46) (completa de caballete lateral y so- 50 Nm (5 kgm).
porte delantero depsito de expansin) desplazndola Remove the cradle (46) (complete with side stand and
c
hacia adelante.
c
expansion tank front support) by moving it forwards.
Al instalar la cuna (46) coloque dentro de ella When reassembling the cradle (46), position
el tubo de compensacin lquido refrigerante the coolant compensating pipe and the en-
c
y el tubo aceite motor (29). gine oil pipe (29) inside it.
c
NOTA (X)
A partir de este punto, durante la instalacin NOTE (X)
del motor sobre el bastidor, siga adelante con los From this point onward, for the reassembly of
procedimientos especficos, vase 3.3 (INSTALA- the engine on the frame proceed according to the
CION MOTOR SOBRE BASTIDOR). specific procedures, see 3.3 (REINSTALLING THE
ENGINE ON THE FRAME).
Manteniendo bloqueada la tuerca (47), destornille el
eje (48) dndole pocas vueltas. Hold the bush (47) and loosen the pin (48) .
Manteniendo bloqueada la tuerca (47), destornille y Hold the bush (47), unscrew and remove the lock ring
saque la tuerca de bloqueo (49) utilizando la llave tu- (49) by means of the apposite socket spanner, see 1.8
bular adecuada, vase 1.8 (EQUIPOS ESPECIALES), (SPECIAL TOOLS), then take the washer.
guarde sucesivamente la arandela. Unscrew the adjusting bush (47) completely.
Destornille del todo la tuerca de regulacin (47).
a a
No hay que extraer del todo el eje del bascu- The rear fork pin (48) must not be withdrawn
lante (48) sino que hay que dejarlo metido lo completely, rather, it must be left in its posi-
suficiente para poder conservar el acopla- tion as much as necessary to maintain the
miento bastidor/basculante sobre el lado derecho, connection frame/fork on the right side, thus prevent-
evitando de esta manera que todo el grupo rueda tra- ing the whole rear wheel/fork unit from moving down-
sera/basculante deslice hacia abajo salindose de la wards and getting therefore misaligned.
alineacin. Si hubiese que volver sucesivamente a In this case the reassembly would be particularly dif-
montarlo resultara sumamente difcil. ficult.
Desenrosque completamente el eje (48). Unscrew the pin (48) completely.
Introduzca en la tuerca de regulacin (47) la herramien- Introduce the apposite tool, see 1.8 (SPECIAL
ta adecuada, vase 1.8 (EQUIPOS ESPECIALES). TOOLS) in the adjusting bush (47).
Utilizando un martillo de goma, d ligeros golpes sobre By means of a rubber hammer, strike the tool slightly
la herramienta hasta llevarla al tope sobre la tuerca de until it reaches the end of stroke on the adjusting bush
regulacin (47). (47).
a a
Como consecuencia del peso (unos 50 kg) y Due to the weight (about 50 kg) and dimen-
del espacio que ocupa el motor, las operacio- sions of the engine, the following operations
nes que siguen necesitan la intervencin de must be performed by two persons.
un segundo operador. Antes de empezar el trabajo Previously check the execution procedures.
compruebe de antemano los procedimientos que hay The removal must be carried out with the greatest
que realizar. La operacin de extraccin debe reali- care.
zarse con el mayor cuidado. Unscrew and remove the nut (50) and withdraw the
Destornille y quite la tuerca (50) y extraiga el tornillo rear lower screw (51) that fastens the engine to the
(51) de fijacin inferior trasero motor/bastidor. frame.
a a
Tras haber extrado el tornillo (51) el motor After the screw (51) has been withdrawn, the
tratar de girar algo hacia adelante (con ful- engine will tend to rotate slightly forwards
c
(with fulcrum on the screw "53").
c
cro sobre el tornillo 53).
Para que la extraccin del tornillo (51) resulte To facilitate the withdrawing of the screw (51),
ms fcil levante apenas el motor. slightly lift the engine.
Destornille y saque la tuerca (52) y extraiga el tornillo Unscrew and remove the nut (52) and withdraw the
(53) de fijacin superior motor /bastidor, guardando la upper screw (53) that fastens the engine to the frame,
arandela. taking the washer.
a a
Ahora, el motor est completamente libre y no The engine is now completely free and is not
tiene ninguna fijacin. Opere con precaucin, fixed in any point. Handle it with caution and
cuidado con los dedos, con los brazos y con be careful not to hurt your fingers, arms or
las piernas. legs.
Aguante el motor desde el lado derecho y desde el Grasp the engine on the right and left side, in the
lado izquierdo, en los puntos donde se pueda sujetar points where your hold is safer, and extract if from
con mayor seguridad, extrigalo desde el lado iz- the left side with slight shifts, trying to find the most
quierdo ladendolo poco a poco, buscando la combi- effective combination of movements.
nacin ms eficaz de movimientos. Place it on the ground on a clean surface and make
sure it remains in position by putting wooden blocks
Apyelo por el suelo sobre una superficie limpia y around it.
utilice unos tacos de madera para que quede en posi-
cin.
3 - 17
MOTORE
a
Le fasce e il paranco devono essere adeguati
a sostenere in tutta sicurezza il motore che
pesa circa 50 kg.
a
Causa il peso (circa 50 kg) e lingombro del
motore, le operazioni che seguono richiedono
lintervento di un secondo operatore. Accer-
tarsi preventivamente sulle procedure di esecuzione.
Loperazione di reinstallazione deve essere svolta
con la massima attenzione.
3 - 18
MOTOR ENGINE
3.3 INSTALACION MOTOR SOBRE BASTIDOR 3.3 REINSTALLING THE ENGINE ON THE
FRAME
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA-
CIONES GENERALES). Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
TION) carefully.
Suspenda el motor segn lo indicado en figura y en-
ganche las fajas en un aparejo para soportarlo. Sling the engine as indicated in the figure and hook the
bands to a hoist for support.
a
Las fajas y el aparejo deben resultar adecua-
a
dos para soportar con la mayor seguridad el The bands and the hoist must be suitable for
motor que pesa unos 50 kg. bearing the weight of the engine, which is
about 50 kg, in total safety.
a
Como consecuencia del peso (unos 50 kg) y
a
del espacio que ocupa el motor, las operacio- Due to the weight (about 50 kg) and dimen-
nes que siguen necesitan la intervencin de sions of the engine, the following operations
un segundo operador. Antes de empezar el trabajo must be performed by two persons. Previous-
compruebe de antemano los procedimientos que hay ly check the execution procedures. The reinstallation
que realizar. La operacin de instalacin debe reali- must be carried out with the greatest care.
zarse con el mayor cuidado.
a
Handle with caution.
a
Opere con precaucin. Be careful not to hurt your fingers, arms or
Cuidado con los dedos, con los brazos y con legs.
las piernas.
Firmly grasp the engine and put it in the right position
Aguante fijamente el motor acompandolo en posi- on the frame on the left side of the vehicle.
cin sobre el bastidor desde el lado izquierdo del veh- Shift the engine with slight movements until reaching
culo. the perfect alignment of the holes "A" for the fastening
Sacuda ligeramente el motor hasta alcanzar la perfec- of the engine to the frame.
ta alineacin de los agujeros de fijacin motor/bastidor
A.
Introduzca el tornillo (1) con la arandela y atornille, sin Introduce the screw (1) with the washer and screw the
apretarla, la tuerca (2) de fijacin superior motor/basti- upper nut (2) that fastens the engine to the frame,
dor. without tightening it.
Empuje el motor desde el lado delantero inferior dn- Push the engine from the front lower side, making it
dole una ligera rotacin hacia atrs (con fulcro sobre perform a slight backward rotation (with fulcrum on the
el elemento de bloqueo A) hasta alcanzar la perfecta holes "A"), until the rear lower holes "B" for the fasten-
alineacin de los agujeros de fijacin inferiores trase- ing of the engine to the frame are perfectly aligned,
ros motor/bastidor B y al mismo tiempo introduzca el and at the same time introduce the fastening screw (3)
tornillo de fijacin (3) y enrosque la tuerca (4). and screw the nut (4).
Par de apriete tuerca/tornillo (4-3): Nut/screw (4-3) driving torque:
50 Nm (5 kgm). 50 Nm (5 kgm).
Apriete la tuerca (2). Tighten the nut (2).
Par de apriete tuerca/tornillo (2-1): Nut/screw (2-1) driving torque:
50 Nm (5 kgm). 50 Nm (5 kgm).
3 - 19
MOTORE
a
Nella prima fase, il perno (5), la bussola di re-
golazione (6) e la ghiera di bloccaggio (7) de-
vono essere avvitati a mano..
a
Da questo punto in poi procedere con la rein-
stallazione motore sul telaio in modo inverso
alla rimozione partendo dalla NOTA (X), vedi
3.2 (RIMOZIONE MOTORE DAL TELAIO).
a
re:
Eseguire un controllo generale su tutti i com-
ponenti su cui si intervenuto e in particola-
3 - 20
MOTOR ENGINE
a a
Durante la primera fase, el eje (5), la tuerca de In the first phase, the pin (5), the adjusting
regulacin (6) y la tuerca de bloqueo (7), de- bush (6) and the lock ring (7) must be screwed
ben ser enroscados manualmente. by hand.
Introduzca y enrosque el eje (5) de fijacin basti- Introduce and screw the pin (5) that fastens frame,en-
dor/motor/basculante, manteniendo bloqueada la tuer- gine and rear fork, holding the adjusting bush (6) and
ca de regulacin (6) utilizando la correspondiente llave using the apposite socket spanner, see 1.8 (SPECIAL
tubular, vase 1.8 (EQUIPOS ESPECIALES). TOOLS).
Enrosque la tuerca de regulacin (6) hasta llegar al to- Screw the adjusting bush (6) until it reaches the end of
pe, siga enroscndola hasta 1/4 de vuelta. stroke, then give it another one fourth turn.
Apriete tuerca de regulacin (6): Tightening of the adjusting bush (6):
contacto + 1/4 de vuelta. contact + one fourth turn.
Manteniendo bloqueada la tuerca de regulacin (6), Hold the adjusting bush (6) and tighten the fork pin (5).
apriete el eje basculante (5).
Pin (5) driving torque: 100 Nm (10 kgm).
Par de apriete eje (5): 100 Nm (10 kgm).
Put back the washer.
Vuelva a colocar la arandela. Hold the adjusting bush (6) and at the same time
Mantenga bloqueada la arandela de regulacin (6) y, a screw the lock ring (7).
la vez, enrosque la tuerca de bloqueo (7).
Lock ring (7) driving torque:
Par de apriete tuerca de bloqueo (7): 40 Nm (4 kgm).
40 Nm (4 kgm).
a
From this point onwards, proceed with the re-
a
A partir de este punto, siga adelante con la installation of the engine on the frame starting
instalacin del motor sobre el bastidor de ma- from NOTE (X), see 3.2 (REMOVING THE EN-
nera opuesta al desmontaje, empezando por GINE FROM THE FRAME) and following the reverse
la NOTA (X), vase 3.2 (EXTRACCION DEL MOTOR order with respect to the removal.
DEL BASTIDOR).
Top up the expansion tank, see 2.14 (CHECKING
Efecte el relleno del lquido refrigerante, vase AND TOPPING UP COOLANT).
2.14 (CONTROL Y RELLENO DEL LQUIDO REFRI- Top up the engine oil tank, see 2.12 (CHECKING THE
GERANTE). ENGINE OIL LEVEL AND TOPPING UP).
Efecte el relleno aceite motor, vase 2.12 (CON- If the engine has been overhauled, bleed the oil deliv-
TROL DEL NIVEL DEL ACEITE DEL MOTOR Y RE- ery pump, see 2.13.1 (AIR BLEEDING FROM OIL
LLENO). DELIVERY PUMP).
En caso de que el motor haya sido revisado, efecte la Check the gearing chain tension and if necessary ad-
purga aire bomba de alimentacin aceite, vase just it, see 2.16.1 (CLEARANCE CONTROL) and
2.13.1 (PURGA DEL AIRE DE LA BOMBA DE ALI- 2.16.3 (ADJUSTMENT).
MENTACIN DEL ACEITE).
a
Controle la tensin de la cadena de transmisin y si Carry out a general check of all the compo-
acaso ajstela, vanse 2.16.1 (CONTROL DEL JUE- nents involved in the operations mentioned
GO) y 2.16.3 (AJUSTE). above, and in particular check the following:
a
Efecte un control general en todos los com- Correct fastening of the electric cables.
ponentes sobre los que se ha trabajado y en Correct introduction of pipes and couplings.
particular:
a
Clutch, accelerator, cold start cables must all move
No deben estar retorcidos y/o aplastados. freely and must not stretch excessively when the han-
dlebar is rotated.
Correct positioning of the gearshift foot lever.
Cables embrague, acelerador, arranque en fro deben Correct oil and coolant level.
deslizarse libremente y no deben tensarse cuando se Correct driving torque of the engine fastening
gira el manillar. screws/nuts.
Correcta colocacin pedal mando cambio.
Nivel correcto del aceite y del lquido refrigerante.
Correcto par de apriete tornillos/tuercas fijacin motor.
3 - 21
MOTORE
3 - 22
1
3
SISTEMA DI ALIMENTAZIONE
4
SISTEMA DE ALIMENTACIN
FUEL SYSTEM
5
4 -1
SISTEMA DI ALIMENTAZIONE
INDICE
SISTEMAGENERAL
DI ALIMENTAZIONE 4
INDICE
4 -2
SISTEMA DE ALIMENTACIN FUEL SYSTEM
4 -3
SISTEMA DI ALIMENTAZIONE
4
6
Legenda
1) Serbatoio carburante.
2) Tappo per il rifornimento.
3) Drenaggio acqua dal tappo serbatoio carburante.
4) Tubo mandata al carburatore.
5) Rubinetto carburante.
Ruotando la leva sul rubinetto possibile avere
le tre posizioni OFF-ON-RES.
OFF = Rubinetto chiuso (i due passaggi sono chiusi).
ON = Rubinetto aperto (il passaggio principale
aperto).
RES = Rubinetto in riserva (si apre il passaggio ausi-
liario).
6) Sensore livello carburante.
7) Filtri su rubinetto principale.
4 -4
SISTEMA DE ALIMENTACIN FUEL SYSTEM
4 -5
SISTEMA DI ALIMENTAZIONE
a
I vapori di carburante sono nocivi alla salute.
Assicurarsi, prima di procedere, che il locale
in cui si opera abbia un adeguato ricambio
daria. Non inalare i vapori di carburante.
Evitare il contatto del carburante con la pelle.
Non fumare e non utilizzare fiamme libere.
Non disperdere il carburante nellambiente.
4.1.1 MANUTENZIONE
Controllare il rubinetto carburante dopo i primi 1000 km (o 5 1
4 mesi) e successivamente ogni 6000 km (o 8 mesi).
c
batoio.
Si consiglia, durante questa operazione, di
procedere anche al lavaggio completo del ser- 3
4 -6
SISTEMA DE ALIMENTACIN FUEL SYSTEM
Lea con cuidado 1.2.1 (COMBUSTIBLE) y 1.4 (PRE- Read 1.2.1 (FUEL) and 1.4 (PRECAUTIONS AND
CAUCIONES E INFORMACIONES GENERALES). GENERAL INFORMATION).
a a
Los vapores del combustible perjudican la sa- Fuel vapours are noxious for the health.
lud. Antes de proceder, cercirese que el local Before proceeding, make sure that the room
en el cual se trabaja tenga una buena ventila- in which you are working is properly ventilat-
cin. No inhale los vapores de combustible. ed. Do not inhale fuel vapours.
Evite el contacto del combustible con la piel. Avoid any contact of the fuel with the skin.
No fume y no utilice llamas libres. Neither smoke, nor use naked flames.
No esparza el combustible en el medio ambiente. Do not dispose of fuel in the environment.
Check the fuel cock after the first 1000 km (or 4 months)
Los filtros (1-2) colocados en el grifo deben limpiarse pe-
and successively every 6000 km (or 8 months).
ridicamente, vase 4.3 (DESMONTAJE GRIFO COM-
BUSTIBLE), ya que los mismos retienen las posibles im-
The filters (1-2) located on the cock must be cleaned pe-
purezas del combustible y con el tiempo no podra llegar
riodically, see 4.3 (REMOVING THE FUEL COCK),
suficiente combustible cuando el motor funciona normal-
since any impurities in the fuel are held back on the fil-
mente.
c
ters and in the long run this may result in the flowing of
an insufficient quantity of fuel for the regular running of
Durante esta operacin se aconseja lavar
the engine.
c
completamente el depsito.
During this operation, it is also advisable to
wash the tank completely.
4 -7
SISTEMA DI ALIMENTAZIONE
a
I vapori di carburante sono nocivi alla salute.
Assicurarsi che il locale in cui si opera abbia
un adeguato ricambio daria.
Non inalare i vapori di carburante.
Non fumare e non utilizzare fiamme libere.
Non disperdere il carburante nellambiente.
Posizionare il veicolo sul cavalletto.
Per lo svuotamento del carburante dal serbatoio, utiliz-
zare una pompa manuale o un sistema simile.
Per lo svuotamento della vaschetta carburatore, infila-
re un tubo flessibile (1) ( i 4 mm e lunghezza 300
mm) sul raccordo di drenaggio della vaschetta.
Posizionare lestremit libera del tubo (1) allinterno di
un contenitore.
Operando attraverso il foro sul telaio (2), aprire lo sca-
rico del carburatore allentando la vite di drenaggio (3).
Quando tutto il carburante sar uscito:
a
Avvitare accuratamente la vite di drenaggio
(3), per evitare perdite di carburante dal carbu-
c
ratore al momento del rifornimento.
Eseguire le operazioni di svuotamento va-
schetta su entrambi i carburatori.
a
Nel rimontaggio verificare lintegrit della
guarnizione OR (6) posizionandola in modo 4
corretto.
a
Nel rimontaggio verificare lintegrit della
guarnizione OR (10) posizionandola in modo
corretto.
4 -8
SISTEMA DE ALIMENTACIN FUEL SYSTEM
4.2 EVACUACION COMBUSTIBLE DEL DEPO- 4.2 DRAINING THE FUEL TANK AND THE CAR-
SITO Y DE LOS CARBURADORES BURETTORS
Lea con cuidado 1.2.1 (COMBUSTIBLE) y 1.4 Read 1.2.1 (FUEL) and 1.4 (PRECAUTIONS AND
(PRECAUCIONES E INFORMACIONES GENERALES). GENERAL INFORMATION) carefully.
a a
Los vapores de combustible perjudican la sa- Fuel vapours are noxious for the health.
lud. Controle que el local en el que se trabaja Before proceeding, make sure that the room
tenga una buena ventilacin. in which you are working is properly ventilat-
No inhale los vapores de combustible. ed. Do not inhale fuel vapours.
No fume ni utilice llamas libres. Neither smoke, nor use naked flames.
No esparza el combustible en el medio ambiente. Do not dispose of fuel in the environment.
Coloque el vehculo sobre el caballete. Position the vehicle on the stand.
Para vaciar el combustible del depsito utilice una Empty the fuel tank by means of a manual pump or a
bomba manual o un sistema semejante. similar system.
Para el vaciado del recipiente carburador, introduzca To drain the float chamber, introduce a flexible pipe (1)
un tubo flexible (1) (dimetro interior 4 mm y longitud (inner 4 mm and length 300 mm) into the draining
300 mm) en el empalme de drenaje del recipiente. union of the chamber.
Coloque la extremidad suelta del tubo (1) dentro de Position the free end of the pipe (1) inside a container.
otro recipiente. Acting through the hole positioned on the frame (2),
Actuando a travs del orificio en el bastidor (2) abra el open the carburettor drain outlet by loosening the
respiradero del carburador aflojando el tornillo de dre- drain screw (3).
naje (3).
When all the fuel has flowed out:
En cuanto haya salido todo el combustible:
a
Tighten the drain screw (3) carefully, to avoid
a
Atornille con cuidado el tornillo de drenaje (3) fuel leaks from the carburettor during refill-
c
para evitar prdidas de combustible del car- ing.
c
burador cuando reposta.
Empty the float chambers of both carburet-
Efecte las operaciones de evacuacin reci- tors.
piente en ambos carburadores.
a
Durante la instalacin compruebe la integri-
dad de la junta trica (6) colocndola de ma-
nera correcta.
a Upon reassembly, make sure that the O-ring
(6) is sound and position it correctly.
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFOR-
CIONES GENERALES). MATION) carefully.
Vace el combustible del depsito, vase 4.2 (EVA- Drain the fuel from the tank, see 4.2 (DRAINING
CUACION COMBUSTIBLE DEL DEPOSITO Y DE THE FUEL TANK AND THE CARBURETTORS).
LOS CARBURADORES). Disconnect the electric connector (7).
Desconecte el conector elctrico (7). Unscrew and remove the two screws (8).
Destornille y quite los dos tornillos (8). Withdraw the gauge unit (9) and take the O-ring (10).
Extraiga la sonda (9) y guarde la junta trica (10).
a
Durante la instalacin compruebe la integri-
dad de la junta trica (10) colocndola de ma-
nera correcta.
a Upon reassembly, make sure that the O-ring
(10) is sound and position it correctly.
4 -9
SISTEMA DI ALIMENTAZIONE / SISTEMA DE ALIMENTACIN / FUEL SYSTEM
c c c
4.5 CARBURATORI 4.5 CARBURADORES 4.5 CARBURETTORS
Su questo veicolo sono in- En este vehculo se han This vehicle is provided
stallati due carburatori, ab- instalado dos carburado- with two carburettors that
binati in modo solidale. res, acoplados de forma solidaria. are integral to each other.
Il loro funzionamento avviene in Funcionan sincrnicamente. Their operation is synchronous.
modo sincrono.
4 - 10
SISTEMA DI ALIMENTAZIONE / SISTEMA DE ALIMENTACIN / FUEL SYSTEM
4 - 11
SISTEMA DI ALIMENTAZIONE
4.5.1 POSIZIONAMENTO
DEL NUMERO DI IDENTIFICAZIONE
I carburatori hanno il numero di identificazione punzonato
sul corpo (lato sinistro), che ne identifica le caratteristiche
(vedi figura).
COMPONENTI CARATTERISTICHE
107,5
Getto principale (M.J.)
110 AC
Spillo (J.N.) 6gh8-55-2 5E 76 - 2
4 - 12
SISTEMA DE ALIMENTACIN FUEL SYSTEM
107,5 107,5
Surtidor principal (M.J.) Main jet (M.J.)
110 AC 110 AC
Aguja (J.N.) 6gh8-55-2 5E 76 - 2 Needle (J.N.) 6gh8-55-2 5E 76 - 2
Surtidor del ralent (P.J.) 17,5 Idling mixture jet (P.J.) 17,5
Surtidor aire ralent (P.A.J.) 1,5 Idling air jet (P.A.J.) 1,5
Lea con cuidado 1.2.1 (COMBUSTIBLE) y 1.4 Read 1.2.1 (FUEL) and 1.4 (PRECAUTIONS AND
(PRECAUCIONES E INFORMACIONES GENERALES). GENERAL INFORMATION) carefully.
Coloque el vehculo sobre el caballete central & o Position the vehicle on the centre stand &, or on an
sobre un adecuado caballete de soporte fijado en los apposite support stand fixed to the couplings of the
pivotes del caballete central. centre stand.
Vace el combustible del depsito y de los carburado- Drain the fuel from the tank and from the carburettors,
res, vase 4.2 (EVACUACION COMBUSTIBLE DEL see 4.2 (DRAINING THE FUEL TANK AND THE
DEPOSITO Y DE LOS CARBURADORES). CARBURETTORS).
Extraiga el depsito del combustible, vase 7.1.1 Remove the fuel tank, see 7.1.1 (REMOVING THE
(DESMONTAJE DEPOSITO COMBUSTIBLE). FUEL TANK).
Quite los paneles laterales, vase 7.1.4 (DESMON- Remove the sides, see 7.1.4 (REMOVING THE
TAJE PANELES LATERALES DERECHO E IZ- RIGHT AND LEFT SIDES).
QUIERDO). Remove the exhaust silencers, see 7.1.10 (REMOV-
Quite los silenciadores de escape, vase 7.1.10 ING THE EXHAUST SILENCERS).
(DESMONTAJE SILENCIADORES DE ESCAPE). Unscrew and remove the screw (1), taking the washer.
Destornille y saque el tornillo (1) guardando la arande- Unscrew and remove the nut (2).
la. Withdraw the screw (3), taking the washer.
Destornille y saque la tuerca (2). Remove the plate (4) that supports the fuel tank.
Haga deslizar el tornillo (3) guardando la arandela. Withdraw the drain pipe (5) from the float chamber.
Saque la placa (4) de soporte depsito combustible.
Haga deslizar el tubo de drenaje (5) desde el recipien-
te del carburador.
4 - 13
SISTEMA DI ALIMENTAZIONE
c NOTA (Y)
Da questo punto in poi nella reinstallazione
dei carburatori, procedere con le specifiche procedu-
re, vedi 4.5.4 (REINSTALLAZIONE CARBURATORI).
a
Non fare ruotare il gruppo reggisella / cassa
filtro oltre il necessario che serve a permette-
re lestrazione dei carburatori.
4 - 14
SISTEMA DE ALIMENTACIN FUEL SYSTEM
Afloje las dos abrazaderas (6-7). Loosen the two clmaps (6-7).
Afloje con una vuelta el tornillo (8) de fijacin inferior Loosen the saddle pillar lower fastening screw (8) by
vstago del silln. giving it about one turn.
Par de apriete tornillo (8): 25 Nm (2,5 kgm). Screw (8) driving torque: 25 Nm (2,5 kgm).
Destornille y quite el tornillo (9) de fijacin superior Unscrew and remove the saddle pillar upper fasten-
vstago del silln y guarde la arandela. ing screw (9) and take the washer.
Par de apriete tornillo (9): 25 Nm (2,5 kgm). Screw (9) driving torque: 25 Nm (2,5 kgm).
c NOTA (Y)
Desde este punto, durante la instalacin de
los carburadores siga adelante con los procedimien-
c NOTE (Y)
From this point onwards, for the reinstallation
of the carburettors proceed according to the specific
tos especficos, vase 4.5.4 (INSTALACION CAR- procedures, see 4.5.4 (REINSTALLING THE CAR-
BURADORES). BURETTORS).
D unos golpes con la palma de la mano sobre el por- Strike the luggage rack with the palm of your hand
taequipajes (golpes fuertes pero sin exceder) hasta (firmly, but moderately) until the whole saddle pillar/fil-
que todo el vstago del silln/caja filtro no realice una ter case unit performs a slight downward rotation (with
ligera rotacin (con fulcro en A) hacia abajo de ma- fulcrum in A), thus allowing the two couplings (10-11)
nera que los dos manguitos (10-11) se suelten de los to be released from the carburettors.
carburadores.
a
Do not make the saddle pillar/filter case unit
a
No gire el grupo vstago del silln/caja filtro rotate more than is necessary to extract the
ms de lo necesario para permitir la extrac- carburettors.
cin de los carburadores.
4 - 15
SISTEMA DI ALIMENTAZIONE
a
Non estrarre i carburatori completamente ma
quanto basta a facilitare lo scollegamento del
cavo acceleratore e del cavo del dispositivo
per lavviamento a freddo.
a
Tappare le aperture dei manicotti (sul cilindro
e sulla cassa filtro), impedendo lentrata di
corpi estranei.
4 - 16
SISTEMA DE ALIMENTACIN FUEL SYSTEM
a a
No extraiga los carburadores del todo, sino lo Do not extract the carburettors completely,
suficiente para facilitar la desconexin del ca- but only as much as necessary to facilitate the
ble acelerador y del cable del dispositivo para disconnection of the accelerator cable and of
el arranque en fro. the cold start device cable.
Aguante fijamente los carburadores con las dos ma- Grasp the carburettors firmly with your hands and with-
nos y squelos de los dos colectores sobre la culata, draw them from the two manifolds on the cylinder, by
sacudindolos moderadamente en sentido vertical. shaking them moderately in vertical direction.
Desconecte del carburador izquierdo el cable mando Disconnect the accelerator control cable (13) from the
acelerador (13). left carburettor.
Destornille de todo el tornillo de fijacin (14) y extraiga Unscrew the fastening screw (14) completely and with-
el dispositivo para el arranque en fro completo. draw the whole cold start device.
Extraiga del todo los carburadores. Remove the carburettors completely.
a a
Tape las aberturas de los manguitos (sobre el Plug the coupling openings (on cylinder and
cilindro y sobre la caja filtro), impidiendo la filter case), to avoid any accidental introduc-
entrada de cuerpos extraos. tion of foreign matters.
Antes de seguir adelante con la instalacin de los car- Before proceeding to the reinstallation of the carburet-
buradores, extraiga del empalme el tubo de alimenta- tors, withdraw the fuel pipe from the pipe fitting, extract
cin, saque el filtro (15) y lmpielo. the filter (15) and clean it.
4 - 17
SISTEMA DI ALIMENTAZIONE
a
Prima di procedere con la reinstallazione dei
carburatori, verificare che le due valvole a far-
falla (1-2) siano perfettamente allineate, even-
tualmente intervenire sulla vite (3).
a
Da questo punto in poi procedere con la rein-
stallazione dei carburatori in modo inverso al-
la, rimozione partendo dalla NOTA (Y), vedi
4.5.3 (RIMOZIONE CARBURATORI).
a
Ultimata la reinstallazione pu essere neces-
sario un eventuale intervento di regolazione
sui cavi dellaccelleratore e dellavviamento a
freddo, vedi 2.9 (CAVO ACCELERATORE) e 2.10
(CAVO AVVIAMENTO A FREDDO).
4 - 18
SISTEMA DE ALIMENTACIN FUEL SYSTEM
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFOR-
CIONES GENERALES). MATION) carefully.
a a
Antes de seguir adelante con la instalacin de Before proceeding to the reinstallation of the
los carburadores, compruebe que las dos vl- carburettors, make sure that the two throttle
vulas de mariposa (1-2) estn perfectamente valves (1-2) are perfectly aligned and if neces-
alineadas, en caso contrario intervenga en el tornillo sary adjust the screw (3).
(3).
Introduzca el dispositivo para el arranque en fro en su Introduce the cold start device in the apposite seat on
sede correspondiente sobre el carburador izquierdo, the left carburettor, tightening the fastening screw (4).
apretando el tornillo de fijacin (4). Reconnect the accelerator control cable (5) on the left
Vuelva a conectar el cable mando acelerador (5) sobre carburettor.
el carburador izquierdo. Introduce the carburettors in the two manifolds (6-7).
Introduzca los carburadores sobre los dos manguitos Tighten the two screws on the clamps (8-9).
(6-7). Grasp the luggage rack, lift the saddle pillar/filter case
Apriete los dos tornillos sobre las abrazaderas (8-9). unit and gradually insert the carburettors in the two
Aguante el portaequipajes y levantando el grupo vs- manifolds of the cylinder, at the same time aligning the
tago del silln/caja filtro acompae la introduccin de fastening holes (B).
los carburadores sobre los dos colectores del cilindro
a
y, a la vez, ponga en lnea los agujeros de fijacin (B).
Make sure that the carburettors are correctly
a
Controle que los carburadores hayan sido in- inserted in the two manifolds of the cylinder.
troducidos correctamente sobre los dos co-
lectores del cilindro. Tighten the screw on the clamp (10).
a
Apriete el tornillo sobre la abrazadera (10). From this point onwards, proceed with the re-
installation of the carburettors starting from
a
A partir de este punto, siga adelante con la NOTE (Y), see 4.5.3 (REMOVING THE CAR-
instalacin de los carburadores actuando de BURETTORS) and following the reverse order with
manera contraria al desmontaje, empezando respect to the removal.
por la NOTA (Y), vase 4.5.3 (DESMONTAJE CAR-
a
BURADORES). Once the carburettors have been reinstalled, it
may be necessary to adjust the accelerator
a
Una vez acabada la instalacin podra resultar cable, see 2.9 (ACCELERATOR CABLE) and
necesario ajustar los cables del acelerador y the cold start cable, see 2.10 (COLD START CA-
del arranque en fro, vanse 2.9 (CABLE DEL BLE).
ACELERADOR) y 2.10 (CABLE DEL ARRANQUE EN
FRO).
4 - 19
SISTEMA DI ALIMENTAZIONE
a
Le operazioni che seguono si riferiscono allo
smontaggio del carburatore sinistro, comun-
que le stesse sono valide anche per quello de-
stro. Nel caso vengano smontati entrambi i carbura-
tori porre attenzione a non mischiare i componenti
(alcuni sembrano uguali ma non lo sono).
a
Nel rimontaggio controllare che la guarnizio-
ne (4) non sia danneggiata e sia correttamente
posizionata nella sede cava sulla vaschetta.
a
Lo smontaggio e il successivo rimontaggio
dei componenti deve essere svolto con la
massima attenzione in quanto un danneggia-
mento anche minimo ad alcuni di essi pu influire ne-
gativamente sulla carburazione e quindi sul rendi-
mento del motore.
4 - 20
SISTEMA DE ALIMENTACIN FUEL SYSTEM
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFOR-
CIONES GENERALES). MATION) carefully.
Desmonte los carburadores del vehculo, vase Remove the carburettors from the vehicle, see 4.5.3
4.5.3 (DESMONTAJE CARBURADORES). (REMOVING THE CARBURETTORS).
a a
Las operaciones que siguen se refieren al The following operations refer to the disas-
desmontaje del carburador izquierdo, sin em- sembly of the left carburettor, but are obvi-
bargo las mismas tienen validez incluso para ously valid also for the right carburettor.
el carburador derecho. En caso de que se desmonten If both carburettors are disassembled, be careful not
los dos carburadores ponga cuidado en no mezclar to mix up the components (some of them look alike,
los componentes (algunos parecen iguales pero no but they arent).
lo son).
Coloque los carburadores con los recipientes dirigidos Position the carburettors with the chambers facing up-
hacia lo alto encima de una superficie limpia y libre de wards on a clean and clear surface.
objetos. Unscrew and remove the two screws (1-2) that fasten
Destornille y quite los dos tornillos (1-2) de fijacin del the chamber.
recipiente. Lift and remove the chamber (3).
Levante y saque el recipiente (3).
a
Upon reassembly make sure that the gasket
a
Durante la instalacin controle que la junta (4) (4) is not damaged and that it is correctly posi-
no est daada y que est colocada correcta- tioned in the hollow seat on the chamber.
mente en el hueco correspondiente sobre el
a
recipiente. The disassembly and the successive reas-
sembly of the components must be carried
a
El desmontaje y la sucesiva reinstalacin de out with the greatest care, since even the
los componentes debe efectuarse con el ma- slightest damage to any of them may negatively af-
yor cuidado en cuanto si uno de ellos se es- fect the carburetion and therefore the engine efficien-
tropea, aunque mnimamente, esto podra influir ne- cy.
gativamente sobre la carburacin y por lo tanto
sobre el rendimiento del motor. Firmly press the float unit (5) with two fingers (see fig-
ure) and withdraw it from its seat by lifting it.
Apriete fijamente con dos dedos (vase figura) el gru-
a
po flotador (5) y levantndolo extrigalo de su sede.
Upon reassembly make sure that the needle
a
Durante la instalacin controle que la vlvula valve correctly fits in its seat (6).
de aguja se instale correctamente en su sede
(6).
4 - 21
SISTEMA DI ALIMENTAZIONE
a
Nel rimontaggio controllare lintegrit della
membrana (21) e il corretto posizionamento
del bordo esterno sulla sede cava del corpo
carburatore.
4 - 22
SISTEMA DE ALIMENTACIN FUEL SYSTEM
Forzando apenas en los dos puntos de apoyo, separe By forcing slightly on the two fulcrum points, separate
el flotador (7) del soporte (8) guardando la vlvula de the float (7) from the support (8) and take the needle
aguja (9) y teniendo cuidado con no daar la pinza valve (9), being careful not to damage the clip (10).
(10).
Extraiga y saque de su alojamiento la sede vlvula de Withdraw the needle valve seating (11) and remove it
aguja (11). from its housing.
Destornille y quite el surtidor del mximo (12). Unscrew and remove the maximum speed mixture jet
(12).
Destornille y quite el tornillo de regulacin aire (13) Unscrew and remove the air screw (13), taking the
guardando el muelle (14), la arandela (15) y la junta spring (14), the washer (15) and the O-ring (16).
trica (16). Overturn the carburettors.
Vuelque los carburadores. Unscrew and remove the two screws (17-18) and take
Destornille y quite los dos tornillos (17-18) y guarde las the washers.
arandelas correspondientes. Remove the cover (19).
Quite la tapa (19). Withdraw the spring (20).
Extraiga el muelle (20). Take the membrane (21) as indicated in the figure and
Coja la membrana (21) segn lo indicado en figura y lift it, thus withdrawing the whole unit.
levante extrayendo todo el equipo.
a
Upon reassembly make sure that the mem-
a
Durante la instalacin controle la integridad brane (21) is sound and that its outer edge is
de la membrana (21) y la colocacin correcta correctly positioned on the hollow seat of the
del borde exterior sobre el hueco del cuerpo carburettor body.
carburador.
4 - 23
SISTEMA DI ALIMENTAZIONE
a
Nel rimontaggio controllare che lo spillo coni-
co (23) si inserisca correttamente nel foro di
sede.
4 - 24
SISTEMA DE ALIMENTACIN FUEL SYSTEM
Vuelque el grupo membrana/vlvula de guillotina (21- Overturn the membrane/gate valve unit (21-22) and
22) y guarde la aguja cnica (23), la arandela de tope take the conical needle (23), the washer (24) and the
(24) y el anillo (25). ring (25).
a a
Durante la instalacin controle que la aguja
cnica (23) pueda introducirse correctamente Upon reassembly make sure that the conical
en el agujero de sede. needle (23) correctly fits in the seat hole.
Actuando segn lo indicado en figura, extraiga la Proceeding as indicated in the figure, remove the
membrana (21) de la vlvula de guillotina (22). membrane (21) from the gate valve (22).
4.5.8 CONTROL DISPOSITIVO PARA EL ARRANQUE 4.5.8 CHECKING THE COLD START DEVICE
EN FRIO
Make sure that the device is sound; it must not show
Compruebe la integridad del dispositivo; no debe estar dents, scratches, etc.
abollado, ni tener araazos, etc..... The rubber part indicated in the figure must no show evi-
La parte de caucho indicada en la figura, no debe estar dent signs of wear.
visiblemente gastada. If you notice any of the anomalies described above,
Si se nota una de las imperfecciones indicadas hay que change the device.
sustituir el dispositivo.
4 - 25
SISTEMA DI ALIMENTAZIONE
4 - 26
1
4
IMPIANTO DI RAFFREDDAMENTO
5
SISTEMA DE REFRIGERACIN
COOLING SYSTEM
6
5 -1
IMPIANTO DI RAFFREDDAMENTO
INDICE
IMPIANTOGENERAL
DI RAFFREDDAMENTO 5
INDICE
1 5.1 DESCRIZIONE .........................................Pag. 5-4
5.1.1 LIQUIDO REFRIGERANTE ..................Pag. 5-4
5.2 RIMOZIONE RADIATORE .....................Pag. 5-6
5 -2
SISTEMA DE REFRIGERACIN COOLING SYSTEM
5 -3
IMPIANTO DI RAFFREDDAMENTO
5 -4
SISTEMA DE REFRIGERACIN COOLING SYSTEM
El lquido caliente, al salir de la culata, encuentra : The warmed liquid that comes out of the head meets:
El termistor (1) que registra la temperatura y la tran- Ehe thermistor (1) that takes its temperature and tran-
smite al indicador temperatura lquido refrigerante (2) smits the relevant value to the coolant temperature in-
(en el salpicadero) que la visualiza. dicator (2) (on the dashboard) that displays it.
El radiador (3), a travs del manguito (4), el lquido The radiator (3) through the coupling (4): the fluid first
ocupa antes su mitad superior y luego se vierte en la occupies its upper part and then flows to the lower part
parte inferior saliendo sucesivamente del manguito (5). and out of the coupling (5).
La vlvula termosttica (del tipo de pastilla de cera The thermostatic valve (type with heat-sensitive wax)
sensible al calor) la cual, segn la temperatura del that, according to the coolant temperature, regulates its
lquido, regula el flujo en el radiador (3). flow into the radiator (3).
A los 60-70 la vlvula termosttica empieza a abrirse, At 60 - 70C the thermostatic valve starts opening; at
a unos 85 la vlvula se abre del todo y deja salir el about 85C it opens completely and lets the fluid flow
lquido a su mximo caudal. with maximum delivery.
Para ms informaciones, vase el MANUAL DE TAL- For further information, see the ENGINE SERVICE
LER MOTOR, N 933 (D-UK)/ N 934 (I-E-F). MANUAL, n. 933 (D-UK) / n. 934 (I-E-F).
Sobre el radiador est colocado el termointerruptor (6) The radiator is provided with the thermal switch (6), which
que se acciona y pone en funcin el electroventilador (7), snaps and operates the electrofan (7) if the liquid temper-
si la temperatura del lquido en esta zona llega a los ature in this area reaches 90C.
90C.
When the operation of the electrofan brings the coolant
Cuando, por medio de la accin del electroventilador, la temperature back to 80C, the thermal switch snaps
temperatura del lquido alcanza los 80C, el termointe- again and disconnects the electrofan.
rruptor se pone en funcin otra vez desconectando el
electroventilador. The coolant volume increase (caused by the temperature
increase) is compensated for in the expansion tank (8),
El aumento del volumen del lquido (debido al incremento through the pipe (9).
de la temperatura) se compensa en el depsito de ex-
pansin (8), mediante el tubo (9).
5 -5
IMPIANTO DI RAFFREDDAMENTO
a
Liberare tutti i cavi e i tubi dalle relative fa-
scette di fissaggio situate lungo il percorso.
Premunirsi poi di altrettante fascette da utiliz-
zare nel rimontaggio.
5 -6
SISTEMA DE REFRIGERACIN COOLING SYSTEM
Lea con cuidado 1.2.5 (LQUIDO REFRIGERANTE) y Read 1.2.5 (COOLANT) and 1.4 (PRECAUTIONS AND
1.4 (PRECAUCIONES E INFORMACIONES GENERA- GENERAL INFORMATION) carefully.
LES).
Descargue del todo el circuito de refrigeracin, vase Drain the cooling circuit completely, see 2.15
2.15 (SUBSTITUCIN DEL LQUIDO REFRIGERAN- (CHANGING THE COOLANT).
TE). Remove the fuel tank, see 7.1.1 (REMOVING THE
Saque el depsito del combustible, vase 7.1.1 (DES- FUEL TANK).
MONTAJE DEPOSITO COMBUSTIBLE). Remove the front fairing, see 7.1.14 (REMOVING THE
Extraiga el carenado delantero, vase 7.1.14 (DES- FRONT FAIRING).
MONTAJE CARENADO DELANTERO). Unscrew and remove the screws (1).
Destornille y saque los tornillos (1). Remove the air conveyor (2).
Extraiga el encauzador aire (2). Withdraw the protection element (3) and disconnect
Saque el elemento de proteccin (3) y desconecte el the electric terminal (4) from the thermistor (5).
terminal elctrico (4) del termistor (5). Disconnect the electric connector (6) of the electrofan
Desconecte el conector elctrico (6) del electroventila- (7).
dor (7).
a a
Suelte todos los cables y los tubos de sus co- Release all the cables and pipes from the fas-
rrespondientes abrazaderas de bloqueo. tening clamps positioned along them. Get oth-
Prepare, luego, un nmero igual de abrazade- er clamps to be used for the reassembly.
ras que habr que utilizar durante la instalacin.
Desconecte los dos conectores elctricos (8-9) del ter- Disconnect the two electric connectors (8-9) from the
mointerruptor (10). thermal switch (10).
Ladee la abrazadera (11) y saque de la boca el tubo Move the pipe clamp (11) and withdraw the coolant
de compensacin (12). compensating pipe (12) through the filler neck.
Corte la cabeza de las abrazaderas (13) y (14). Cut the head of the pipe clamps (13) and (14).
Saque de los enganches radiador los dos manguitos Withdraw the two couplings (15) and (16) from the ra-
(15) y (16). diator connections.
5 -7
IMPIANTO DI RAFFREDDAMENTO
Se necessario:
Svitare e togliere il termointerruttore (10) recuperando
la guarnizione.
Rimuovere lelettroventola di raffreddamento, vedi 5.3
(RIMOZIONE ELETTROVENTOLA DI RAFFREDDA-
MENTO)(sesto punto).
a
Corpi estranei, sporcizia ecc. appiccicati alle
alette del radiatore devono essere rimossi uti-
lizzando un getto daria in pressione.
Eventuali alette piegate devono essere raddrizzate
utilizzando un piccolo cacciavite a intaglio.
Se i manicotti (15-16) presentano tagli e/o screpolatu-
re devono essere sostituiti.
a
Prima del rimontaggio procedere con un ac-
curato lavaggio interno del radiatore usando
solamente acqua pulita.
5 -8
SISTEMA DE REFRIGERACIN COOLING SYSTEM
Haga deslizar del anillo-gua (17) los cables elctricos Withdraw the electric cables of the thermistor and of
del termistor y del termointerruptor y el tubo de com- the thermal switch and the compensating pipe (12)
pensacin (12). from the cable guide ring (17).
Destornille y saque la tuerca de seguridad (18). Unscrew and remove the self-locking nut (18).
Saque el tornillo (19) guardando la arandela y si Withdraw the screw (19), taking the washer and if
acaso la brjula y la goma. necessary also the bush and the rubber element.
c
hculo).
Durante la instalacin coloque correctamente
el anillo-gua (20) (en el lado izquierdo del ve- c
cle).
Upon reassembly, position the cable guide
ring (20) correctly (on the left side of the vehi-
Incline apenas hacia adelante el radiador (21) y, a la Incline the radiator (21) slightly forwards and at the
vez, levntelo extrayendo de su sede, sobre el soporte same time lift it, withdrawing the two lower anchorage
radiador (22), los dos pernos inferiores de anclaje (23- pins (23-24) from their seat on the radiator support
24). (22).
Saque el radiador (21) completo de electroventilador Remove the radiator (21), complete with the electrofan
(7) y el termointerruptor (10). (7) and the thermal switch (10).
a a
Hay que quitar los cuerpos extraos, sucie- Foreign matters, filth, etc. sticking to the radi-
dad, etc. que estn pegados a las aletas del ator fins must be removed by means of a jet of
radiador utilizando un chorro de aire bajo pre- compressed air.
sin. Si hay aletas plegadas, tiene que enderezarlas Any bent fins are to be straightened using a small
utilizando un destornillador adecuado pequeo. slotted screwdriver.
Sustituya los manguitos (15-16) si estn cortados y/o If the couplings (15-16) show cuts and/or cracks, they
agrietados. must be replaced.
a a
Antes de la instalacin lave cuidadosamente
el interior del radiador utilizando tan solo agua Before reassembly, thoroughly wash the in-
limpia. side of the radiator with clean water only.
5 -9
IMPIANTO DI RAFFREDDAMENTO
a
Liberare il cavo dalla fascetta di fissaggio (3).
Premunirsi poi di altra fascetta da utilizzare
nel rimontaggio.
c
LIQUIDO REFRIGERANTE).
Il livello del liquido rimanente deve essere al
di sotto del foro dove si inserisce il termoin-
terruttore.
Svitare e togliere il termointerruttore (10) e recuperare
c
la guarnizione.
Nell rimontaggio, applicare sulla filettatura del
termointerruttore (10) LOCTITE 574.
Coppia di serraggio termointerruttore (10): 30 Nm (3
kgm).
Effettuare il rabbocco, vedi 2.14 (CONTROLLO E
RABBOCCO LIQUIDO REFRIGERANTE).
5 - 10
SISTEMA DE REFRIGERACIN COOLING SYSTEM
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
Saque el depsito combustible, vase 7.1.1 (DES- Remove the fuel tank, see 7.1.1 (REMOVING THE
MONTAJE DEPOSITO COMBUSTIBLE). FUEL TANK).
Desmonte el carenado delantero, vase 7.1.14 (DES- Remove the front fairing, see 7.1.14 (REMOVING THE
MONTAJE CARENADO DELANTERO). FRONT FAIRING).
Desconecte el conector elctrico (1) del electroventila- Disconnect the electric connector (1) of the electrofan
dor (2). (2).
a a
Suelte el cable de la abrazadera de bloqueo Release the cable from the fastening clamp
(3). Prepare luego otra abrazadera que habr (3). Get another clamp to be used for the reas-
que utilizar durante la instalacin. sembly.
Destornille y quite los tres tornillos de fijacin (4) y Unscrew and remove the three fastening screws (4)
guarde la redecilla de proteccin (5), la proteccin (6), and take the protection grid (5), the guard (6), the
las arandelas y, si acaso, las brjulas y las gomas. washers and the bushes and rubber elements, if any.
Saque el equipo del electroventilador (2) deslizndolo Remove the whole electrofan (2) withdrawing it down-
hacia abajo y al mismo tiempo desplace apenas el wards and at the same time shift the coupling (7)
manguito (7). slightly.
c c
(SUBSTITUCIN DEL LQUIDO REFRIGERANTE).
The level of the remaining coolant must be be-
El nivel del lquido restante debe estar por de-
low the hole in which the thermal switch is in-
bajo del agujero por el cual se introduce el ter-
serted.
mointerruptor.
Destornille y saque el termointerruptor (10) y guarde la Unscrew and remove the thermal switch (10) and take
c c
junta. the gasket.
Durante la instalacin extienda sobre la rosca Upon reassembly, apply LOCTITE 574 on the
del termointerruptor (10) LOCTITE 574. thread of the thermal switch.
Par de apriete termointerruptor (10): 30 Nm (3 kgm). Termal switch (10) driving torque: 30 Nm (3 kgm).
Efecte el relleno, vase 2.14 (CONTROL Y RELLE- Top up the expansion tank, see 2.14 (CHECKING
NO DEL LQUIDO REFRIGERANTE). AND TOPPING UP COOLANT).
5 - 11
IMPIANTO DI RAFFREDDAMENTO
c
Svitare e togliere il termistore (3).
Non togliere il tappo sul radiatore e/o il tappo
sul vaso di espansione, altrimenti si avr la
c
fuoriuscita di liquido refrigerante.
Nel rimontaggio applicare sulla filettatura del
termistore (3) LOCTITE 574.
Coppia di serraggio termistore (3): 30 Nm (3 kgm).
c
rondella.
Loperazione che segue deve essere svolta
con sufficiente velocit per evitare la fuoriusci-
ta anche minima di liquido dal vaso di espansione (7).
Sfilare il tubo (8) e contemporaneamente tappare con
un dito il foro sul vaso di espansione (7).
a
Il liquido refrigerante nocivo.
Sistemare il vaso di espansione (7) in un luo-
go sicuro.
5 - 12
SISTEMA DE REFRIGERACIN COOLING SYSTEM
Quite el elemento de proteccin (1) y desconecte el Withdraw the protection element (1) and disconnect
terminal elctrico (2). the electric terminal (2).
c c
Desenrosque y quite el termistor (3). Unscrew and remove the thermistor (3).
No quite el tapn del radiador y/o el tapn del Do not remove the radiator cap and/or the ex-
depsito de expansin, de hacerlo el lquido pansion tank cap, otherwise the coolant will
c c
refrigerante comenzar a salir. overflow.
Coloque LOCTITE 574 sobre la rosca del ter- Upon reassembly, apply LOCTITE 574 on the
mistor (3) durante la instalacin. thread of the thermistor (3).
Par de apriete termistor (3): 30 Nm (3 kgm). Thermistor (3) driving torque: 30 Nm (3kgm).
Saque el protector de crter, vase 7.1.9 (DESMON- Remove the oil pan guard, see 7.1.9 (REMOVING
TAJE PROTECTOR DE CARTER). THE OIL PAN GUARD).
Extraiga el tubo de purga (4) del empalme. Withdraw the breather pipe (4) from the pipe fitting.
Destornille y quite el tornillo de fijacin (5) y guarde la Unscrew and remove the fastening screw (5) and take
tuerca. the brush.
Destornille y quite el tornillo de fijacin (6) y guarde la Unscrew and remove the fastening screw (6) and take
c
arandela.
c
the washer.
Hay que realizar bastante rpidamente la ope- The following operation must be performed
racin descrita a continuacin para evitar la rather quickly, in order to avoid even the least
salida, incluso mnima, del lquido del depsito de overflow of coolant from the expansion tank (7).
expansin (7).
Extraiga el tubo (8) y, a la vez, tape con un dedo el Withdraw the pipe (8) and at the same time plug the
agujero sobre el depsito de expansin (7). hole on the expansion tank (7) with a finger.
a a
El lquido refrigerante es nocivo.
Coloque el depsito de expansin (7) en un The coolant is noxious.
lugar seguro. Put the expansion tank (7) in a safe place.
MANTENGASE LEJOS DEL ALCANCE DE LOS NI- KEEP AWAY FROM CHILDREN.
OS.
Remove the expansion tank (7), keeping it right and
Saque el depsito de expansin (7) conservndolo en take the oil pan guard front support.
posicin derecha y guarde el soporte delantero protec-
tor de crter.
5 - 13
IMPIANTO DI RAFFREDDAMENTO / SISTEMA DE REFRIGERACIN / COOLING SYSTEM
5 - 14
1
2
6
5
IMPIANTO ELETTRICO
6
INSTALACIN ELCTRICA
ELECTRICAL SYSTEM
7
6 -1
IMPIANTO ELETTRICO
INDICE GENERAL
IMPIANTO ELETTRICO 6
INDICE
1 6.1 CONTROLLO
SISTEMA DI RICARICA .......................... Pag. 6-4
6.1.1 CONTROLLO TENSIONE DI RICARICA .. Pag. 6-4
6.1.2 CONTROLLO FUNZIONAMENTO
A VUOTO ALTERNATORE ...................... Pag. 6-4
2 6.1.3 CONTROLLO
CONTINUIT ALTERNATORE................. Pag. 6-6
6.1.4 CONTROLLO
REGOLATORE DI TENSIONE.................. Pag. 6-6
6.2 SISTEMA DI ACCENSIONE ................... Pag. 6-8
6.2.1 SCHEMA ELETTRICO .............................. Pag. 6-8
6 -2
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
6.1 CONTROL
DEL SISTEMA DE RECARGA ............... Pag. 6-3
6.1 CHECKING
THE RECHARGING SYSTEM ............... Pag. 6-5
1
6.1.1 CONTROL 6.1.1 CHECKING
DE LA TENSIN DE RECARGA .............. Pag. 6-5 THE RECHARGING VOLTAGE................ Pag. 6-5
6.1.2 CONTROL DEL FUNCIONAMIENTO 6.1.2 CHECKING THE ALTERNATOR
EN VACO DEL ALTERNADOR ............... Pag. 6-5
6.1.3 CONTROL DE LA CONTINUIDAD
DEL ALTERNADOR.................................. Pag. 6-7
LOADLESS OPERATION ......................... Pag. 6-5
6.1.3 CHECKING
THE ALTERNATOR CONTINUITY ........... Pag. 6-7
2
6.1.4 CONTROL 6.1.4 CHECKING
DEL REGULADOR DE TENSIN............. Pag. 6-7 THE VOLTAGE REGULATOR ................. Pag. 6-7
6.2 SISTEMA DE ENCENDIDO .................... Pag. 6-9 6.2 IGNITION SYSTEM .................................. Pag. 6-9
6.2.1 ESQUEMA ELCTRICO ........................... Pag. 6-9 6.2.1 WIRING DIAGRAM.................................... Pag. 6-9
6.2.2 CONTROL DE LA BOBINA AT ................. Pag. 6-9
6.2.3 CONTROL DEL PICK-UP........................ Pag. 6-11
6.2.2 CHECKING THE H.V. COIL ...................... Pag. 6-9
6.2.3 CHECKING THE PICK-UP ...................... Pag. 6-11
3
6.2.4 CONTROL DE LA CENTRALITA C.D.I... Pag. 6-11 6.2.4 CHECKING THE C.D.I............................. Pag. 6-11
6.3 CONTROL DE LA INSTALACIN 6.3 CHECKING
DEL CONECTOR THE ELECTRICAL SYSTEM
DE LA CENTRALITA C.D.I. ................. Pag. 6-13 FROM THE C.D.I. CONNECTOR........ Pag. 6-13
6.4 INDICADOR DE LA TEMPERATURA
DEL LQUIDO REFRIGERANTE ......... Pag. 6-15
6.4 COOLANT TEMPERATURE
INDICATOR ............................................... Pag. 6-15
4
6.4.1 ESQUEMA ELCTRICO ......................... Pag. 6-15 6.4.1 WIRING DIAGRAM.................................. Pag. 6-15
6.4.2 CONTROL DEL INSTRUMENTO ............ Pag. 6-15 6.4.2 CHECKING THE INSTRUMENT ............. Pag. 6-15
6.4.3 CONTROL DEL FUNCIONAMIENTO 6.4.3 CHECKING THE THERMISTOR
DEL TERMISTOR.................................... Pag. 6-17 OPERATION........................................... Pag. 6-17
6.5 CONTROL DEL SENSOR DE LA
PRESIN DEL ACEITE DEL MOTORPag. 6-17
6.5 CHECKING THE ENGINE OIL
LOW PRESSURE SENSOR .................. Pag. 6-17 5
6.6 ELECTROVENTILADOR 6.6 COOLING ELECTROFAN ..................... Pag. 6-19
DE REFRIGERACIN............................. Pag. 6-19 6.6.1 WIRING DIAGRAM.................................. Pag. 6-19
6.6.1 ESQUEMA ELCTRICO ......................... Pag. 6-19 6.6.2 CHECKING
6.6.2 CONTROL DEL FUNCIONAMIENTO THE ELECTROFAN OPERATION.......... Pag. 6-19
DEL ELECTROVENTILADOR ................ Pag. 6-19
6.6.3 CONTROL DEL FUNCIONAMIENTO
DEL TERMOINTERRUPTOR .................. Pag. 6-19
6.6.3 CHECKING THE THERMAL SWITCH
OPERATION ........................................... Pag. 6-19
6.7 STARTING SAFETY SYSTEM ............ Pag. 6-20
6
6.7 SISTEMA DE SEGURIDAD 6.7.1 WIRING DIAGRAM.................................. Pag. 6-20
DEL ARRANQUE ..................................... Pag. 6-20 6.7.2 STARTING
6.7.1 ESQUEMA ELCTRICO ......................... Pag. 6-20 SAFETY OPERATING LOGIC................ Pag. 6-21
6.7.2 LGICA DE FUNCIONAMIENTO
SEGURIDAD DEL ARRANQUE ............. Pag. 6-21
6.7.3 CONTROL DEL REL DE ARRANQUE . Pag. 6-23
6.7.3 CHECKING THE STARTING RELAY ..... Pag. 6-23
6.7.4 CHECKING THE STAND SWITCH ......... Pag. 6-23
6.7.6 CHECKING THE DIODES ...................... Pag. 6-25
7
6.7.4 CONTROL DEL INTERRUPTOR DEL 6.8 FUEL LEVEL CIRCUIT .......................... Pag. 6-27
CABALLETE ........................................... Pag. 6-23 6.8.1 WIRING DIAGRAM.................................. Pag. 6-27
6.7.6 CONTROL DE LOS DIODOS .................. Pag. 6-25 6.8.2 FUEL LEVEL INDICATOR ...................... Pag. 6-27
6.8 CIRCUITO NIVEL COMBUSTIBLE.... Pag. 6-27
6.8.1 ESQUEMA ELECTRICO ......................... Pag. 6-27
6.8.2 INDICADOR NIVEL COMBUSTIBLE ...... Pag. 6-27
6.9 SWITCHES ................................................ Pag. 6-28
6.10 LIGHTS SYSTEM.................................. Pag. 6-31
6.10.1 WIRING DIAGRAM................................ Pag. 6-31
8
6.9 INTERRUPTORES ................................... Pag. 6-28 6.10.2 CHECKING
6.10 INSTALACIN LUCES ........................ Pag. 6-31 THE HIGH BEAM LIGHTS RELAY ....... Pag. 6-31
6.10.1 ESQUEMA ELCTRICO ....................... Pag. 6-31 6.11 BATTERY ................................................ Pag. 6-33
6.10.2 CONTROL DEL REL 6.11.1 ACTIVATING THE BATTERY ............... Pag. 6-33
DE LAS LUCES LARGAS .................... Pag. 6-31 6.11.2 MAINTENANCE..................................... Pag. 6-35
6.11 BATERA .................................................. Pag. 6-33 6.11.3 CHECKING ............................................ Pag. 6-35
6.11.1 ACTIVACIN ......................................... Pag. 6-33 6.11.4 RETURN UNDER GUARANTEE........... Pag. 6-35
6.11.2 MANTENIMIENTO ................................. Pag. 6-35 6.12 CHANGING THE BULBS ................... Pag. 6-37
6.11.3 CONTROL.............................................. Pag. 6-35 6.12.1 CHANGING THE HEADLIGHT BULBS Pag. 6-37
6.11.4 DEVOLUCIN EN GARANTA ............. Pag. 6-35 6.12.2 CHANGING THE REAR LIGHT BULB . Pag. 6-39
6.12 SUBSTITUCIN BOMBILLAS .......... Pag. 6-37 6.12.3 CHANGING THE FRONT
6.12.1 SUBSTITUCION BOMBILLAS FARO DIRECTION INDICATOR BULBS ......... Pag. 6-39
DELANTERO ......................................... Pag. 6-37 6.12.4 CHANGING THE REAR
6.12.2 SUBSTITUCION BOMBILLAS DIRECTION INDICATOR BULBS ......... Pag. 6-39
FARO TRASERO ................................... Pag. 6-39 6.12.5 CHANGING
6.12.3 SUSTITUCION THE PLATE LIGHT BULBS .................. Pag. 6-41
BOMBILLAS INDICADORES 6.12.6 CHANGING
DE DIRECCION DELANTEROS ............ Pag. 6-39 THE DASHBOARD BULBS................... Pag. 6-41
6.12.4 SUSTITUCION 6.13 ADJUSTING HEADLIGHT BEAM.... Pag. 6-43
BOMBILLAS INDICADORES 6.14 CHANGING THE FUSES .................... Pag. 6-43
DE DIRECCION TRASEROS................. Pag. 6-39 6.15 WIRING DIAGRAM Pegaso 650 ..... Pag. 6-44
6.12.5 SUBSTITUCION BOMBILLAS
ILUMINACIN DE LA PLACA
DE MATRCULA .................................... Pag. 6-41
6.12.6 SUBSTITUCION
BOMBILLAS SALPICADERO ............... Pag. 6-41
6.13 REGULACIN HAZ LUMINOSO ...... Pag. 6-43
6.14 SUBSTITUCIN DE LOS FUSIBLES Pag. 6-43
6.15 ESQUEMA ELCTRICO
Pegaso 650 ............................................ Pag. 6-44
6 -3
IMPIANTO ELETTRICO
6 -4
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
6.1 CONTROL DEL SISTEMA DE RECARGA 6.1 CHECKING THE RECHARGING SYSTEM
La siguiente leyenda ser til para consultar esta The following key will be useful in consulting this
seccin. section.
Fusible de 20 A 20 A fuse
6.1.2 CONTROL DEL FUNCIONAMIENTO EN VACO 6.1.2 CHECKING THE ALTERNATOR LOADLESS
DEL ALTERNADOR OPERATION
Quite el panel izquierdo, vase 7.1.4 (DESMONTA- Remove left side panel cover, see 7.1.4 (REMOVING
JE PANELES LATERALES DERECHO E IZQUIER- THE RIGHT AND LEFT SIDES).
DO). Disconnect the alternator cable connector (4).
Desconecte el conector de los cables del alternador (4). Start the engine and let it run until it reaches 5000 rpm.
Arranque el motor y llvelo a 5000 rpm. Using a pocket tester, take the voltage (alternating cur-
Con un tester mida, en rotacin, la tensin (corriente rent a.c.) from the three internal male terminals (yellow
alterna c.a.) entre los tres terminales machos interio- cables (G)) in rotation.
res (cables amarillos (G)). If the value indicated by the tester is lower than 70 V,
Si el valor indicado por el tester es inferior a 70 V, el the alternator is defective.
alternador no funciona correctamente. Standard loadless voltage:
Tensin en vaco estndar: more than 70 V (a.c.) at 5000 rpm
superior a 70 V (c.a.) a 5000 rpm
6 -5
IMPIANTO ELETTRICO
G G G V R/Bi M
G 1- 1-
Terminale negativo ()
G 1- 1-
del tester su:
G 1- 1-
V 1-
R/Bi 1- 1- 1- 2- 2-
M 1- 1-
a
Questo metodo di misura approssimativo;
se possibile verificare il corretto funziona-
mento della ricarica utilizzando un altro rego-
latore sicuramente funzionante.
6 -6
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
a
bos cables (5) y (6).
On reassembly, re-connect both cables (5)
Con un tester (escala x 1 k), mida del lado del regu-
and (6).
lador (terminales machos interiores), la resistencia en-
tre los cables indicados en la tabla indicada a conti- Using a pocket tester (scale x 1 k), measure from the
nuacin. regulator side (internal male terminals) the resistance
between the cables indicated in the table below.
Si la resistencia medida es incorrecta, substituya el re- If the resistance measured is not correct, replace the
gulador regulator.
Terminal positivo (+) del tester sobre: Positive terminal (+) of the tester on:
G G G V R/Bi M G G G V R/Bi M
G 1- 1- G 1- 1-
Terminal negativo ()
Negative terminal ()
G 1- 1- G 1- 1-
del tester sobre:
G 1- 1- G 1- 1-
V 1- V 1-
R/Bi 1- 1- 1- 2- 2- R/Bi 1- 1- 1- 2- 2-
M 1- 1- M 1- 1-
a a
Este mtodo de medicin es aproximado; si This measuring method is approximate; if
es posible, controle el funcionamiento correc- possible check the correct operation of the re-
to de la recarga utilizando otro regulador que charging system using another regulator in
est seguro que funcione. perfect condition.
6 -7
IMPIANTO ELETTRICO
Legenda figura
A-B) Misure
15) Bobina AT
16) Nucleo ferroso bobina (massa)
17) Tester
a
Valori standard: Questo metodo di misura approssimativo;
se possibile verificare il corretto funziona-
Misura A : 0,1 0,4 mento della bobina sostituendola con altra si-
Misura B : 6 12 k curamente funzionante.
6 -8
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
a a
Este mtodo de medicin es aproximado; si This measuring method is approximate; if
es posible, compruebe el funcionamiento co- possible, check the correct operation of the
rrecto de la bobina substituyndola con otra coil by replacing the same with another one
que est seguro que funcione. which surely works.
6 -9
IMPIANTO ELETTRICO
A motore spento:
Rimuovere la fiancatina sinistra, vedi 7.1.1 (RIMO-
ZIONE SERBATOIO CARBURANTE).
Scollegare il connettore (1) e effettuare le misure (sui
terminali lato pick-up).
Con un tester (scala x 100), misurare la resistenza
tra i terminali dei cavi blu/giallo (B/G) e verde/bianco
(V/Bi).
Valore standard: 150 350
Se la resistenza infinita () o inferiore al valore pre-
scritto il pick-up deve essere sostituito.
Az V Ar N Bi R
Az 1- 1- 1- 1- 1-
Terminale negativo ()
V 1- 1- 1- 1- 1-
del tester su:
Ar 1- 1-
N 1- 1- 1- 1- 1-
Bi 1- 1- 1- 1- 1-
R 1- 1- 1- 1- 1-
a
Poich all'interno della centralina C.D.I. vi
sono diodi, condensatori e altri componenti
elettronici, il metodo di misura indicato ap-
prossimativo.
Si consiglia di procedere a un ulteriore controllo so-
stituendo la centralina con un'altra sicuramente fun-
zionante, oppure di eseguire i controlli previsti nel
capitolo 6.3 (CONTROLLO IMPIANTO ELETTRICO
DA CONNETTORE CENTRALINA C.D.I.).
6 - 10
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
Terminal positivo (+) del tester sobre: Positive terminal (+) of the tester on:
Az V Ar N Bi R Az V Ar N Bi R
Az 1- 1- 1- 1- 1- Az 1- 1- 1- 1- 1-
Terminal negativo (-)
V 1- 1- 1- 1- 1- V 1- 1- 1- 1- 1-
del tester sobre:
Ar 1- 1- Ar 1- 1-
N 1- 1- 1- 1- 1- N 1- 1- 1- 1- 1-
Bi 1- 1- 1- 1- 1- Bi 1- 1- 1- 1- 1-
R 1- 1- 1- 1- 1- R 1- 1- 1- 1- 1-
a a
El mtodo de medicin es aproximado, ya que The C.D.I. contains diodes, condensers and
en el interior de la centralita C.D.I. hay diodos, other electronic components therefore the
condensadores y otros componentes electr- measuring method indicated is approximati-
nicos. ve. It is advisable to carry out a further check by re-
Es aconsejable proceder con un ulterior control, placing the C.D.I. with another one known to be in
substituyendo la centralita con otra que est seguro perfect condition, or to carry out the checking opera-
que funcione, o bien, realice los controles previsto tions indicated in chapter 6.3 (CHECKING THE
en el captulo 6.3 (CONTROL DE LA INSTALACIN ELECTRICAL SYSTEM FROM THE C.D.I. CONNEC-
DEL CONECTOR DE LA CENTRALITA C.D.I.). TOR).
6 - 11
IMPIANTO ELETTRICO
Interruttore
Se il valore diverso
Cavi daccensione Misura Valore
controllare
in posizione
6 - 12
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
6.3 CONTROL DE LA INSTALACIN DEL Terminal pick-up (cable blanco/azul claro (Bi/Az)).
CONECTOR DE LA CENTRALITA C.D.I. Terminal alimentacin (cable rojo/negro (R/N)).
Quite el panel izquierdo, vase 7.1.4 (DESMONTA- Terminal masa (cable azul marino (B)).
JE PANELES LATERALES DERECHO E IZQUIER- Terminal bobina AT (cable anaranjado (Ar)).
DO).
Desconecte el conector elctrico (1) de la centralita Terminal resistencia anticipo (cable verde/blanco
C.D.I. (2). (V/Bi)).
Con un tester efecte la medicin indicadas en la tabla Terminal seguridad arranque (cable verde/marrn
sobre los terminales hembras, que estn en el interior (V/M)).
del conector elctrico (1), del lado opuesto a la centra-
lita C.D.I.
Interruptor de en- Si el valor es diferente,
Cables Medida Valor
cendido en posicin controle
blanco/azul (Bi/Az) y masa motor m ohm () 150 350 cableado pick-up
azul marino (B) y masa motor m ohm () 01 cableado
verde/blanco (V/Bi) y masa motor m ohm () 4 11 k cableado
anaranjado (Ar) y masa motor m ohm () 02 cableado bobina AT
anaranjado/blanco (Ar/Bi) m
y masa motor (primario bobina ohm () infinito cableado
desconectado)
rojo/gris (R/Gr) y azul marino (B) cableado alternador-masa,
n volt (V) 12 V*
fusibles, interruptor de en-
cendido, interruptor de
(motor parado)
emergencia de arranque
del motor.
verde/marrn (V/M) 0 1 (con el cambio
y azul marino (B) m ohm () en punto muerto y
cableado seguridad
arranque
soporte levantado)
Si los valores resultan correctos pero se verifica un fun- (*) El valor debe indicar la tensin de la batera ( 0,5V).
cionamiento incorrecto, substituya la centralita C.D.I.,
que seguramente est daada.
6.3 CHECKING THE ELECTRICAL SYSTEM Pick-up terminal (white/blue cable (Bi/Az)).
FROM THE C.D.I. CONNECTOR Supply terminal (red/black cable (R/N)).
Remove the left side panel, see 7.1.4 (REMOVING Earth terminal (blue cable (B)).
THE RIGHT AND LEFT SIDES). H.V. coil terminal (orange cable (Ar)).
Disconnect the electric connector (1) of the C.D.I. (2).
Using a tester, carry out the measurements indicated Spark advance resistance terminal (green/white cable
in the table on the internal female terminals of electric (V/Bi)).
connector (1) on the side opposite the C.D.I. Starting safety terminal (green/brown cable (V/M)).
Ignition switch Unit of mea-
Cables Value If value different, check
in position surement
white/light blue (Bi/Az) and engi-
ne earth
m ohm () 150 350 pick-up wiring
blue (B) and engine earth m ohm () 01 wiring
green/white (V/Bi) and engine
earth
m ohm () 4 11 k wiring
orange (Ar) and engine earth m ohm () 02 coil wiring AT
orange/white (Ar/Bi) m
and engine earth (coil primary ohm () infinite wiring
disconnected)
red/grey (R/Gr) and blue (B) wiring of earth alternator,
n volt (V) 12 V*
fuses, ignition switch,
(engine off) emergency switch for en-
gine starting.
green/brown (V/M) and blue (B) 01
m ohm () (gear in neutral and starting safety wiring
stand lifted)
If the values are correct but there is still a malfunction, (*) Values must indicate the battery voltage ( 0,5V).
change the C.D.I., which is certainly defective.
6 - 13
IMPIANTO ELETTRICO
1000 40 C (A)
15 120 C (C)
6 - 14
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
6 - 15
IMPIANTO ELETTRICO
Temperatura
Valori standard
liquido refrigerante
()
(C)
60 600 - 470
90 215 - 175
120 93 - 73
a
Se i valori non variano, oppure si discostano
troppo da quelli riportati in tabella sostituire il
termistore.
6 - 16
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
120 93 - 73 120 93 - 73
a a
Si los valores no varan, o bien, son muy dife- If values do not vary, or if they depart excessi-
rentes de aqullos indicados en la tabla, subs- vely from those indicated in the table, change
tituya el termistor. the thermistor.
6.5 CONTROL DEL SENSOR DE LA PRESIN 6.5 CHECKING THE ENGINE OIL LOW
DEL ACEITE DEL MOTOR PRESSURE SENSOR
Para controlar el funcionamiento del sensor: To check the operation of the sensor:
Extraiga la proteccin de goma (1). Slip off the rubber protection (1).
Desconecte el terminal elctrico del sensor (2). Disconnect the electric terminal from the sensor (2).
Con un tester (escala x 100), compruebe la continui- With a tester (scale x 100) check the continuity bet-
dad entre el terminal de lengeta (3) y la carcasa del ween the tongued terminal (3) and the casing of the
sensor. sensor.
Valor correcto con el motor apagado: 0 Correct value with engine off : 0
Valor correcto con el motor en funcionamiento: Correct value with engine in motion:
Si los valores no corresponden con aqullos indicados, If the values do not correspond to the indicated ones,
controle que el nivel de aceite del motor sea correcto y, check that the engine oil level is correct and change the
eventualmente, substituya el sensor. sensor if necessary.
6 - 17
IMPIANTO ELETTRICO
Temperatura
Valori standard
liquido refrigerante
()
(C)
inferiore a 90
superiore a 80 0
6 - 18
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
a a
Si los valores son muy distintos de aqullos If the values depart excessively from those in-
indicados en la tabla, substituya el termointe- dicated in the table, change the thermal
rruptor. switch.
6 - 19
IMPIANTO ELETTRICO / INSTALACIN ELCTRICA / ELECTRICAL SYSTEM
Legenda schema elettrico Pie de la ilustracin del esquema Wiring diagram key
elctrico
1) Interruttore di accensione 1) Ignition switch ( n - m - s )
(n-m-s) 1) Interruptor de encendido 2) Engine stop switch ( n - m )
(n-m-s)
2) Interruttore arresto motore 3) Starting pushbutton (r)
(n-m) 2) Interruptor parada motor
(n-m) 4) C.D.I.
3) Pulsante avviamento (r)
3) Botn de arranque (r) 5) Neutral gear pilot light ( q )
4) Centralina C.D.I. (green color)
5) Spia cambio in folle ( q ) 4) Centralita C.D.I.
6) Starting relay
(colore verde) 5) Luz indicadora del cambio en
punto muerto ( q ) (color verde) 7) Starter
6) Rel avviamento
6) Rel de arranque 8) Clutch lever switch
7) Motorino avviamento
7) Motor de arranque 9) Stand switch
8) Interruttore leva frizione
8) Interruptor de la palanca del em- 10) Neutral gear switch
9) Interruttore cavalletto
brague 11) Diodes
10) Interruttore cambio in folle
9) Interruptor del soporte 12) Battery
11) Diodi
10) Interruptor del cambio en punto
12) Batteria muerto
11) Diodos
12) Batera
6 - 20
IMPIANTO ELETTRICO / INSTALACIN ELCTRICA / ELECTRICAL SYSTEM
POSIZIONE
LEVA FRIZIONE ACCENSIONE MOTORE MOTORINO
POSIZIONE CAMBIO CAVALLETTO
PALANCA DEL ENCENDIDO DEL AVVIAMENTO
POSICIN DEL CAMBIO POSICIN DEL
EMBRAGUE MOTOR MOTOR DE ARRANQUE
GEAR POSITION CABALLETE
CLUTCH LEVER ENGINE IGNITION STARTER
STAND POSITION
AZIONATA
ACCIONADA
SOLLEVATO PULLED UP
LEVANTADO
LIFTED RILASCIATA
NO ACCIONADA
IN FOLLE RELEASED
EN PUNTO MUERTO
IN NEUTRAL AZIONATA GIRA
ACCIONADA GIRA
ABBASSATO PULLED UP FUNZIONA TURNING OVER
BAJADO FUNCIONA
LOWERED RILASCIATA WORKING
NO ACCIONADA
RELEASED
AZIONATA
ACCIONADA
SOLLEVATO PULLED UP
LEVANTADO
LIFTED RILASCIATA
NO ACCIONADA
MARCIA
INSERITA RELEASED
MARCHA PUESTA
AZIONATA NON GIRA
GEAR ENGAGED
ACCIONADA NO GIRA
ABBASSATO PULLED UP NON FUNZIONA NOT TURNING OVER
BAJADO NO FUNCIONA
LOWERED RILASCIATA NOT WORKING
NO ACCIONADA
RELEASED
6 - 21
IMPIANTO ELETTRICO
6 - 22
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
6.7.3 CONTROL DEL REL DE ARRANQUE 6.7.3 CHECKING THE STARTING RELAY
Extraiga las dos protecciones de goma (2 - 3). Slip off the two rubber protections (2-3).
Desconecte los cables (4 - 5) de los terminales corres- Disconnect the cables (4-5) from the relative terminals
pondientes sobre el rel (6). on relay (6).
Alimente con una batera de 12 V los dos terminales From relay side, feed with a 12V battery the two inter-
interiores al conector (1) del lado del rel. nal terminals of connector (1).
Con un tester (en funcionamiento como ohmetro) con- Using a tester (acting as Ohmmeter) check the conti-
trole la continuidad entre los dos contactos de tornillo nuity between the two screw contacts on the relay.
sobre el rel.
Correct value with relay fed: 0
Valor correcto con rel alimentado: 0 Correct value with relay not fed:
Valor correcto con rel no alimentado:
If the values do not correspond to those indicated, chan-
Substituya el rel si los valores que se obtienen no co- ge the relay.
rresponden con aqullos indicados.
6.7.4 CONTROL DEL INTERRUPTOR DEL CABALLETE 6.7.4 CHECKING THE STAND SWITCH
Los muelles (2) no deben estar daados, oxidados The springs (2) must not be damaged, rusted and/or
ni/o debilitados. weakened.
El interruptor (3) debe estar fijado correctamente. The switch (3) must be fixed correctly.
Para controlar el funcionamiento del sistema de bloqueo To check the operation of the ignition disabling system:
del encendido:
Sit on the saddle.
Suba al silln.
Lift up the stand and put the gear in neutral.
Levante el caballete y ponga el cambio en punto muer-
Start the engine with clutch pulled and engage the ge-
to.
ar.
Arranque el motor con el embrague puesto y ponga la
Lower the stand.
marcha.
At this point the stand will press the switch, causing
Baje el caballete.
switching off of engine.
En este momento, el caballete debe empujar el inte-
If this does not occur, change the switch.
rruptor que apagar el motor.
Si sto no sucediese, substituya el interruptor.
6 - 23
IMPIANTO ELETTRICO
6 - 24
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
Si el tester no tiene la funcin de prueba diodos, utilice If the tester does not include the diode test function, use
una batera de 12 V y una bombilla de 12 V - 2 W co- a 12V battery and a 12V-2W bulb, connecting the diode
nectando el diodo segn lo indicado en figura.. as indicated in the figure.
Prueba (C): la bombilla no se enciende. Test (C): the bulb does not light up.
Prueba (D): la bombilla se enciende. Test (D): the bulb lights up.
6 - 25
IMPIANTO ELETTRICO
Indicazione
Tra i cavi Resistenza
corretta
arancio/nero (Ar/N)
0 spia accesa
- blu (B)
6 - 26
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
Control funcionamiento luz testigo reserva combusti- Checking the operation of the low fuel warning light
ble Directly connect (resistance 0) the orange/black
Conecte directamente (resistencia 0) los cables na- (Ar/N) and blue (B) cables of the connector (8) (har-
ranja/negro (Ar/N) y azul marino (B) del conector (8) ness side); make sure that the low fuel warning light
(lado conjunto de cables); compruebe que la luz testi- comes on.
go reserva combustible se encienda.
Indicacin Correct
Entre los cables Resistencia Between cables Resistance
correcta indication
6 - 27
IMPIANTO ELETTRICO / INSTALACIN ELCTRICA / ELECTRICAL SYSTEM
o
p
r
n
m
GRUPPO INTERRUTTORI LATO SINISTRO
GRUPO DE INTERRUPTORES DEL LADO IZQUIERDO
LEFT SIDE SWITCH SET
5) Deviatore luci / Desviador luces / Dimmer switch
6) Interruttore lampeggio luce abbagliante /
Interruptor de destello intermitente de la luz de carretera /
High beam blinking switch
7) Interruttore indicatori di direzione / Interruptor de los indica-
dores de direccin / Direction indicator switch
8) Pulsante avvisatore acustico. / Pulsador del claxon / War-
ning horn push button
Cavi / Cables / Cables
Pos
Gr B B/N Az R V/N Bi N G/N
f
k
l
a
a
b
6 - 28
IMPIANTO ELETTRICO / INSTALACIN ELCTRICA / ELECTRICAL SYSTEM
Azionato
Accionado
Operating
Pos. VITE
TORNILLO
SCREW
Folle
Punto muerto
Neutral
4) INTERRUTTORE CAVALLETTO
INTERRUPTOR DEL CABALLETE
STAND SWITCH
Cavi / Cables /
Pos. cavalletto
Caballete
Cables 4
Stand M V N
Abbassato
Bajado
Down
Sollevato
Levantado
Up
6 - 29
IMPIANTO ELETTRICO
1) Interruttore di accensione ( n - m - s )
2) Allaccensione
3) Rel luci abbaglianti
4) Devioluci sinistro
5) Devioluci destro
6) Lampade luci di posizione posteriore
7) Fanale anteriore completo
8) Lampade illuminazione strumenti
9) Spia luci di posizione (p) (colore verde)
10) Spia luci abbaglianti (a) (colore blu)
11) Lampada luce di posizione anteriore
12) Batteria
13) Lampada biluce anabbagliante/abbagliante
14) Lampada abbagliante
6 - 30
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
6.10.2 CONTROL DEL REL DE LAS LUCES 6.10.2 CHECKING THE HIGH BEAM LIGHTS RELAY
LARGAS
To check operation of relay:
Para controlar el funcionamiento del rel: Remove the dashboard fairing, see 7.1.17 (REMO-
Desmonte el tablero de instrumentos, vase 7.1.17 VING THE DASHBOARD FAIRING).
(DESMONTAJE TABLERO DE INSTRUMENTOS). Disconnect connector (15) from relay (3).
Desconecte el conector (15) del rel (3). Feed with a 12V battery the two internal male termi-
Alimente con una batera de 12 V los dos terminales nals (1 - 2)
machos interiores (1 - 2). Using a tester (acting as ohmmeter) check continuity
Con un tester (en funcionamiento como Ohmmetro) between the other two terminals (3 - 5).
controle la continuidad entre los otros dos terminales
(3 - 5). Correct value with relay fed: 0
Valor correcto con rel alimentado: 0 Correct value with relay not fed:
Valor correcto con rel no alimentado:
If the values do not correspond to those indicated, chan-
Substituya el rel si los valores que resultan no corres- ge the relay.
ponden con aqullos indicados.
6 - 31
IMPIANTO ELETTRICO
6.11 BATTERIA
Tipo: 12V - 12 Ah
6.11.1 ATTIVAZIONE
Rimuovere la batteria dal veicolo, vedi 7.1.13 (RIMO-
ZIONE BATTERIA).
Togliere il tappo (1) sullo sfiato.
Togliere i tappi (2) dagli elementi.
Riempire i vani degli elementi con liquido elettrolitico
fino a raggiungere il livello MAX.
6 - 32
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
Lea con mucha atencin 2.3 (BATERA). Read 2.3 (BATTERY) carefully.
Cargue la batera lentamente (con un amperaje igual a Recharge the battery for at least 10 hours, using a
1/10 de la capacidad de la batera misma) por 10 ho- trickle charge (amperage corresponding to 1/10 batte-
ras al menos. ry capacity).
Monte nuevamente la batera en el vehculo cuando Put battery back on vehicle at delivery of vehicle to cli-
entregue el vehculo al cliente. ent.
6 - 33
IMPIANTO ELETTRICO
6.11.2 MANUTENZIONE
Nel caso il veicolo rimanga inattivo per lungo tempo
(periodo invernale) ricaricare la batteria almeno una
volta al mese completamente, usando una ricarica len-
ta.
Ripristinare periodicamente (circa una volta al mese) il
livello del liquido elettrolitico con sola acqua distillata.
a
Nei periodi estivi controllare il livello pi fre-
quentemente in quanto laumento della tem-
peratura esterna comporta di conseguenza
una evaporazione pi veloce.
6.11.3 CONTROLLO
In caso di anomalia eseguire innanzitutto un controllo al
circuito di ricarica accertandosi che funzioni correttamen-
te vedi 6.1 (CONTROLLO SISTEMA DI RICARICA).
a
Dopo la ricarica controllare la densit
dellelettrolito utilizzando un densimetro.
Se in qualche vano la densit inferiore a 1,26
e la tensione a vuoto inferiore a 12 V, assoluta-
mente necessario sostituire la batteria.
6 - 34
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
a
Check the level more frequently during the
a
En los perodos calurosos, controle el nivel summer as the increase in environmental tem-
ms frecuentemente, ya que el aumento de la perature means a more rapid evaporation of
temperatura exterior, provoca una evapora- the liquid.
cin ms veloz.
Spread a film of neutral grease or vaseline on the ter-
Coloque una pelcula de grasa neutra o vaselina sobre minals.
los bornes.
a
After recharging, check the density of the
a
Tras la recarga, controle la densidad del electrolyte using a densimeter.
electrolito, utilizando un densmetro. If the density is lower than 1.26 and the no-
Si en alguno de los vasos la densidad es infe- load voltage is lower than 12V in any of the compart-
rior a 1,26 y la tensin en vaco es inferior a 12 V, es ments, it is absolutely necessary to change the bat-
indispensable substituir la batera. tery.
6 - 35
IMPIANTO ELETTRICO
a
Prima di sostituire una lampada, ruotare lin-
terruttore di accensione nella posizione m.
Sostituire la lampada indossando guanti puliti
o utilizzando un panno pulito ed asciutto.
a
Non lasciare impronte sulla lampadina, in
quanto potrebbero causarne il surriscalda-
mento e quindi la rottura.
Se si tocca la lampadina con le mani nude, pulirla con
alcool dalle eventuali impronte, per evitare che si
danneggi anticipatamente.
Per la sostituzione:
LAMPADINA DI POSIZIONE
Posizionare il veicolo sul cavalletto.
c
Per linstallazione:
Inserire la lampadina nel portalampada, fa-
cendo coincidere i due piolini lampadina con
le rispettive guide sul portalampada.
Installare correttamente una lampadina dello stesso ti-
po.
6 - 36
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
Lea con mucha atencin 1.4 (PRECAUCIONES E IN- Read 1.4 carefully (PRECAUTIONS AND GENERAL
FORMACIONES GENERALES). INFORMATION).
a a
Antes de substituir una bombilla, gire el inte- Before changing a bulb, turn the ignition
rruptor de encendido hacia la posicin m. switch to the m position.
Substituya la bombilla ponindose guantes Change the bulb wearing clean gloves or
limpios o utilizando un pao limpio y seco. using a clean, dry cloth.
a a
No deje huellas sobre la bombilla ya que po- Do not leave fingerprints on the bulb as they
dran causar el sobrecalentamiento y, por lo may cause its overheating and consequent
tanto, la rotura de la misma. breakage.
Si toca la bombilla con las manos sin proteccin, lim- If you touch the bulb with bare hands, remove any
pie las posibles huellas con alcohol, para evitar que fingerprints with alcohol to avoid damaging it ahead
se daen anticipadamente. of time.
Una bombilla luz de posicin (2). One parking light bulb (2).
Una bombilla luz de cruce/luz larga (3) (lado derecho). One low/high beam bulb (3) (right side).
Desplace con las manos el elemento de proteccin Move the protection element (4) with your hands.
(4). Seize the bulb socket (5), pull it and remove it from its
Sujete el casquillo portalmparas (5), estrelo y desco- seat.
nctelo de su sede. Withdraw the parking light bulb (2) and replace it with
Extraiga la bombilla de posicin (2) y sustityala con one of the same type.
otra del mismo tipo.
BOMBILLA LUZ LARGA (LADO IZQUIERDO) HIGH BEAM BULB (LEFT SIDE)
Coloque el vehculo sobre el caballete. Position the vehicle on the stand.
Desplace con las manos el elemento de proteccin (6). Move the protection element (6) with your hands.
Suelte el muelle de retencin (7) colocado detrs del
Release the check spring (7) positioned at the rear of
casquillo portalmparas (8). the bulb socket (8).
Extraiga la bombilla (1) y sustityala.
Extract the bulb (1) and replace it.
c
Para la instalacin:
c
For the installation:
Introduzca la bombilla en el casquillo porta- Insert the bulb in the bulb socket, making the
lmparas haciendo coincidir las dos espigas two bulb pins coincide with the relevant gui-
con las correspondientes guas sobre el portalmpa- des on the socket.
ras.
Correctly install a new bulb of the same type.
Instale correctamente otra bombilla del mismo tipo.
6 - 37
IMPIANTO ELETTRICO
Per la sostituzione:
Posizionare il veicolo sul cavalletto.
c
Per linstallazione:
Inserire la lampadina nel portalampada, fa-
cendo coincidere i due piolini lampadina con
le rispettive guide sul portalampada.
Installare correttamente una lampadina dello stesso ti-
po.
Per la sostituzione:
Posizionare il veicolo sul cavalletto.
a
Nel riassemblaggio, serrare con cautela e mo-
deratamente le due viti (4) onde evitare di dan-
neggiare il vetro protettivo.
Premere moderatamente la lampadina (6) e ruotarla in
senso antiorario.
c
Estrarre la lampadina dalla sede.
Inserire la lampadina nel portalampada fa-
cendo coincidere i due piolini guida con le
rispettive guide sul portalampada.
Installare correttamente una lampadina dello stesso ti-
po.
Per la sostituzione:
Posizionare il veicolo sul cavalletto.
a
Nel riassemblaggio, serrare con cautela e mo-
deratamente la vite (7) onde evitare di danneg-
giare il vetro protettivo.
Premere moderatamente la lampadina (9) e ruotarla in
senso antiorario.
c
Estrarre la lampadina dalla sede.
Inserire la lampadina nel portalampada fa-
cendo coincidere i due piolini guida con le
rispettive guide sul portalampada.
Installare correttamente una lampadina dello stesso ti-
po.
6 - 38
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
6.12.2 SUBSTITUCION BOMBILLAS FARO TRASERO 6.12.2 CHANGING THE REAR LIGHT BULB
Destornille y quite los dos tornillos (1). Unscrew and remove the two screws (1).
Tire del cristal de proteccin (2) hacia el exterior ac- Pull the protection glass outwards (2), by exerting
tuando en la zona inferior. pressure on the lower area.
Presione moderadamente la bombilla (3) y grela en Press the bulb (3) slightly and rotate it anticlockwise.
sentido antihorario. Extract the bulb from its seat.
Extraiga la bombilla de su sede.
For the installation:
c c
Para la instalacin:
Insert the bulb in the bulb socket, making the
Introduzca la bombilla en el casquillo porta-
two bulb pins coincide with the relevant gui-
lmparas haciendo coincidir las dos espigas
des on the socket.
con las correspondientes guas sobre el casquillo
portalmparas.
Correctly install a new bulb of the same type.
Instale correctamente otra bombilla del mismo tipo.
Destornille y quite los dos tornillos (4). Unscrew and remove the two screws (4).
a a
Durante el reensamblaje, apriete con cuidado Upon reassembly, tighten the two screws (4)
y moderadamente los dos tornillos (4) para no carefully, in order not to damage the protec-
daar el cristal de proteccin. tion glass.
Presione moderadamente la bombilla (6) y grela en Press the bulb (6) slightly and rotate it anticlockwise.
sentido antihorario. Extract the bulb from its seat.
c c
Extraiga la bombilla de su sede.
Insert the bulb in the bulb socket, making the
Introduzca la bombilla en el casquillo porta-
two bulb pins coincide with the relevant gui-
lmparas haciendo coincidir las dos espigas
des on the socket.
gua con las correspondientes guas sobre el casqui-
llo portalmparas.
Correctly install a new bulb of the same type.
Instale correctamente otra bombilla del mismo tipo.
Destornille y quite el tornillo (7). Unscrew and remove the screw (7).
a a
Durante el reensamblaje, apriete con cuidado Upon reassembly, tighten the screw (7) care-
y moderadamente el tornillo (7) para no daar fully, in order not to damage the protection
el cristal de proteccin. glass.
Presione moderadamente la bombilla (9) y grela en Press the bulb (9) slightly and rotate it anticlockwise.
sentido antihorario.
c
Extract the bulb from its seat.
c
Extraiga la bombilla de su sede.
Insert the bulb in the bulb socket, making the
Introduzca la bombilla en el casquillo porta- two bulb pins coincide with the relevant gui-
lmparas haciendo coincidir las dos espigas des on the socket.
gua con las correspondientes guas sobre el casqui-
Correctly install a new bulb of the same type.
llo portalmparas.
Instale correctamente otra bombilla del mismo tipo.
6 - 39
IMPIANTO ELETTRICO
Per la sostituzione:
Posizionare il veicolo sul cavalletto.
Per la sostituzione:
Posizionare il veicolo sul cavalletto.
Spia Descrizione
c indicatori di direzione
g riserva carburante
p luci di posizione
q cambio in folle
a luci abbaglianti
6 - 40
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
6.12.5 SUBSTITUCION BOMBILLA LUZ MATRCULA 6.12.5 CHANGING THE NUMBER PLATE BULB
Destornille y quite el tornillo (1). Unscrew and remove the screw (1).
Extraiga la bombilla luz matrcula (4) y sustityala con Withdraw the number plate bulb (4) and replace it with
otra del mismo tipo. a new one of the same type.
Desmonte el carenado delantero, vase 7.1.14 Remove the front fairing, see 7.1.14 (REMOVING
(DESMONTAJE CARENADO DELANTERO). THE FRONT FAIRING).
Extraiga el portalmpara de goma y substituya la bom- Remove the relative rubber bulb socket and change
billa si es necesario. the bulb if necessary.
Una debajo del indicador de la temperatura del l- One bulb under coolant temperature indicator (A).
quido refrigerante (A). One bulb under speedometer/odometer (B).
Una bombilla debajo del taqumetro/cuentakilme- Six bulb under the dashboard of the warning lights
tros (B). (D).
Seis debajo del salpicadero de las luces testigos One bulb under revolution counter
(D).
Una debajo del cuentarrevoluciones. Warning light Description
6 - 41
IMPIANTO ELETTRICO
DISPOSIZIONE FUSIBILI
a
Non utilizzare mai fusibili diversi da quelli
specificati.
Si potrebbero creare danni al sistema elettrico
o persino un incendio in caso di corto circuito.
6 - 42
INSTALACIN ELCTRICA ELECTRICAL SYSTEM
Encienda la luz de cruce, sintese en el vehculo y con- Turn on the low beam, sit on the vehicle and make sure
trole que el haz de luz proyectado sobre la pared est un that the beam projected on the wall is slightly under the
poco por debajo de la lnea horizontal del proyector (9/10 horizontal line of the headlight (approx. 9/10 of the total
de la altura total aproximadamente - vase Figura). height - see figure).
Lea con mucha atencin 1.4 (PRECAUCIONES E IN- Read 1.4 carefully (PRECAUTIONS AND GENERAL
FORMACIONES GENERALES). INFORMATION).
Si comprueba que un componente elctrico no funciona If an electric component does not work or works irregular-
o funciona mal, o que el motor no arranca, es necesario ly , or if the vehicle fails to start, the fuses must be
controlar los fusibles: checked:
Coloque el interruptor de encendido en la posicin Turn the ignition switch to the m position to prevent
m, para evitar un cortocircuito accidental. any accidental short circuit.
Quite el silln, vase 7.1.3 (DESMONTAJE SILLIN). Remove saddle, see 7.1.3 (REMOVING THE SADD-
Extraiga un fusible por vez (A-B-C) y controle que el fi- LE).
lamento no est quemado. Extract one fuse at a time (A-B-C) and check to see if
Antes de substituir un fusible, trate de localizar, si es the filament is interrupted.
posible, la causa que ha provocado el inconveniente. Before replacing a fuse, try to discover the cause of
Luego, substituya el fusible quemado con otro con el the trouble, if possible.
c
mismo amperaje. Replace the damaged fuse with a new one having the
c
same amperage.
En el portafusibles hay tres fusibles de re-
puestos. Three spare fuses are to be found on the fuse
carrier.
a
llave hasta: Never use fuses different from the specified
el encendido, lgica de seguridad del arranque. ones. The use of unsuitable fuses may cause
damage to the electric system or, in case of a
a
Nunca utilice fusibles diferentes de aqullos short circuit, even fire.
c
indicados. Se podra producir desde un dao
al sistema elctrico hasta un incendio en caso When a fuse blows frequently, there is proba-
de cortocircuito. bly a short circuit or an overload in the elec-
c
tric system.
Cuando un fusible salta frecuentemente, es
probable que en la instalacin elctrica haya
un cortocircuito o una sobrecarga.
6 - 43
IMPIANTO ELETTRICO / INSTALACIN ELCTRICA / ELECTRICAL SYSTEM
6 - 44
IMPIANTO ELETTRICO / INSTALACIN ELCTRICA / ELECTRICAL SYSTEM
CABLE COLOURS
COLORE CAVI Ar orange
COLORES DE LOS CABLES Az light blue
Ar arancio B blue
Az azzurro Ar anaranjado Bi white
B blu Az azul claro G yellow
Bi bianco B azul marino Gr grey
G giallo Bi blanco M brown
Gr grigio G amarillo N black
M marrone Gr gris R red
N nero M marrn Ro pink
R rosso N negro V green
Ro rosa R rojo Vi violet
V verde Ro rosa
Vi viola V verde
Vi violeta
6 - 45
IMPIANTO ELETTRICO / INSTALACIN ELCTRICA / ELECTRICAL SYSTEM
6 - 46
1
6
CICLISTICA
7
PARTE CICLO
CHASSIS PARTS
8
7 -1
&,&/,67,&$
6 7.1.23 RIMOZIONE
CATENA DI TRASMISSIONE ................ Pag. 7-30
7.1.24 RIMOZIONE
7.1.4 DESMONTAJE PANELES LATERALES
DERECHO E IZQUIERDO .........................Pag. 7-9
7.1.5 DESMONTAJE
ROTELLE E PATTINO CATENA ........... Pag. 7-30 PORTAEQUIPAJES TRASERO..............Pag. 7-11
7.1.25 RIMOZIONE CAVALLETTO LATERALE Pag. 7-32 7.1.6 DESMONTAJE GRUPO
7.1.26 RIMOZIONE GUARDABARROS DELANTERO...........Pag. 7-11
-
7 CAVALLETTO CENTRALE
7.1.27 RIMOZIONE POGGIAPIEDI PILOTA .... Pag. 7-32
............ Pag. 7-32
7 -2
3$57(&,&/2 &+$66,63$576
7 -3
&,&/,67,&$ 3$57(&,&/2 &+$66,63$576
5 6
7
8
4 9 10 11
12
3
2 13
14
1 16 15
26 27 28
21 22 23 25
24
20
29 30 31
19
18
17 34 33 32
7 -4
&,&/,67,&$ 3$57(&,&/2 &+$66,63$576
7 -5
&,&/,67,&$
I vapori di carburante sono nocivi alla salute.
Assicurarsi, prima di procedere, che il locale
in cui si opera abbia un adeguato ricambio
daria.
Non inalare i vapori di carburante.
Non fumare e non utilizzare fiamme libere.
Non disperdere il carburante nellambiente.
3
possibile rimuovere il serbatoio dal veicolo
F
con o senza carburante al suo interno. Nella
prima ipotesi, prima di procedere con le operazioni
OF
che seguono, provvedere allo svuotamento, vedi 4.2
(SVUOTAMENTO CARBURANTE DAL SERBATOIO E 2 4
DAI CARBURATORI).
7 -6
3$57(&,&/2 &+$66,63$576
Lea con cuidado 1.2.1 (COMBUSTIBLE), 1.4 (PRE- Read 1.2.1 (FUEL), 1.4 (PRECAUTIONS AND GENER-
CAUCIONES E INFORMACIONES GENERALES) y 4.1 AL INFORMATION) and 4.1 (FUEL TANK) carefully.
(SERBATOIO CARBURANTE).
Los vapores del combustible perjudican la sa- Fuel vapours are noxious for the health.
lud. Anter de seguir adelante controle que el Before proceeding, make sure that the room
lugar donde trabaja tenga un adecuado cam- in which you are working is properly venti-
bio de aire. lated.
No inhale los vapores de combustible. Do not inhale fuel vapours.
No fume ni utilice llamas libres. Neither smoke, nor use naked flames.
No esparza el combustible en el ambiente. Do not dispose of fuel in the environment.
X Desmonte el silln, vase 7.1.3 (DESMONTAJE SI- X Remove the saddle, see 7.1.3 (REMOVING THE SAD-
LLIN). DLE).
al mismo tiempo, extrigalo de los dos alojamientos
(en la parte delantera) tirndolo hacia atrs. Upon reassembly, make sure that the tank fits
correctly into the relative seats in the front
Al volverlo montar, controle que el depsito part.
entre correctamente en los respectivos aloja-
mientos de la parte delantera. X If necessary, remove the fuel cock, see 4.3 (REMOV-
ING THE FUEL COCK), the fuel level gauge unit, see
X Desmonte, si es necesario, el grifo, vase 4.3 (DES- 4.4 (REMOVING THE FUEL LEVEL GAUGE UNIT)
MONTAJE GRIFO COMBUSTIBLE), la sonda nivel, and the cap, see 7.1.2 (REMOVING THE FILLER
vase 4.4 (DESMONTAJE SONDA NIVEL COMBUS- CAP).
TIBLE) y el tapn, vase 7.1.2 (DESMONTAJE TA-
PON DEPOSITO COMBUSTIBLE). For further information, see 4.1 (FUEL TANK).
7 -7
&,&/,67,&$
I vapori di carburante sono nocivi alla salute.
Assicurarsi, prima di procedere, che il locale
in cui si opera abbia un adeguato ricambio
daria.
Non inalare i vapori di carburante.
Non fumare e non utilizzare fiamme libere. Non di-
sperdere il carburante nellambiente.
PERICOLO DI INCENDIO E/O ESPLOSIONE
X Svitare e togliere le 3 viti (1).
Le altre tre viti possono rimanere montate in
quanto hanno solo una funzione estetica.
X Aprire il tappo (2).
X Svitare e togliere la vite (3).
X Rimuovere il tappo (2) completo di ghiera (4).
X Rimuovere nellordine, la guarnizione (5), la vaschetta
(6) e la guarnizione vaschetta (7).
Nel rimontaggio posizionare correttamente la
guarnizione vaschetta (7) e la vaschetta (6) in
modo che coincidano i fori.
re la sella (10).
Prima di abbassare e bloccare la sella, con-
trollare di non aver dimenticato la chiave nel
portaoggetti.
X Per bloccare la sella: posizionare la linguetta (11) nella
sede, abbassare e premere la sella, facendo scattare la
serratura.
Operare con cautela.
Non danneggiare le linguette e/o le relative
sedi dincastro.
Maneggiare con cura i componenti verniciati, non
strisciarli o rovinarli.
X + Svitare e togliere le quattro viti (12).
+ Rimuovere la fiancatina (13).
X
7 -8
3$57(&,&/2 &+$66,63$576
SITO DE COMBUSTIBLE). Fuel vapours are noxious for the health.
Before proceeding, make sure that the room
Los vapores del combustible perjudican la sa- in which you are working is properly venti-
lud. Antes de seguir adelante controle que el lated.
lugar donde trabaja tenga un adecuado cam- Do not inhale fuel vapours.
bio de aire. Neither smoke, nor use naked flames.
No inhale los vapores de combustible. Do not dispose of fuel in the environment.
No fume ni utilice llamas libres. No esparza el com-
bustible en el ambiente. RISK OF FIRE AND/OR EXPLOSION.
PELIGRO DE INCENDIO Y/O DE EXPLOSIN
X Position the vehicle on the stand.
X Coloque el vehculo sobre el caballete. X Unscrew and remove the three screws (1).
X Destornille y saque los tres tornillos (1). The other three screws can be left on the vehi-
cle, since they have only an aesthetic func-
Los otros tornillos pueden quedar instalados
tion.
en cuanto tienen slo una funcin esttica.
X Open the cap (2).
X Abra el tapn (2).
X Unscrew and remove the screw (3).
X Destornille y quite el tornillo (3).
X Remove the cap (2) together with the metal ring (4).
X Saque el tapn (2) junto con el casquillo (4).
X Remove the gasket (5), the small container (6) and the
X Desmonte, en este orden, la junta (5), la cubeta (6) y la
container seal (7) in the given order.
junta de la cubeta (7).
Upon reassembly, position the container seal
Al volverlas montar, coloque la junta de la cu-
(7) and the container (6) correctly, so that the
beta (7) y la cubeta (6) de forma que los aguje-
holes coincide.
ros coincidan perfectamente.
lln (10). (10).
Antes de bajar y de bloquear el silln, controle Before lowering and locking the saddle, make
que no haya olvidado la llave en el vano porta- sure that you have not left the key in the glove
documentos/kit herramientas. compartment.
X Para bloquear el silln: ponga la lengeta (11) en su X To lock the saddle, position the tang (11) in its seat,
alojamiento, baje el silln y haga presin sobre ste then lower and press the saddle, thus making the lock
hasta or el resorte de la cerradura. snap shut.
7.1.4 DESMONTAJE PANELES LATERALES 7.1.4 REMOVING THE RIGHT AND LEFT SIDES
DERECHO E IZQUIERDO
X Remove the saddle, see 7.1.3 (REMOVING THE SAD-
X Quite el silln, vase 7.1.3 (DESMONTAJE SILLIN). DLE).
Acte con cuidado. Proceed with care.
No dae las lengetas y/o los correspondien- Do not damage the tangs and/or the relevant
tes soportes de acoplamiento. seatings.
Maneje con cuidado los componentes barnizados Handle the painted components with care and avoid
para no rayarlo o daarlos. scraping or damaging them.
X + Destornille y saque los cuatro tornillos (12). X + Unscrew and remove the four screws (12).
+ Quite el panel lateral (13). + Remove the side (13).
X X
Si la proteccin anticalor (14) (en el interior de If the antiheat guard (14) (on the inner side) is
los paneles) est daada, sustityala. in bad conditions, change it.
7 -9
&,&/,67,&$
X
Maneggiare con cura i componenti verniciati,
non strisciarli o rovinarli.
Svitare e togliere la vite (5).
8
X
Nel rimontaggio posizionare correttamente la
fascetta (7) e il collare (8).
Sfilare il parafango (9) dalla parte anteriore.
9
11
7.1.7 RIMOZIONE PORTATARGA
Leggere attentamente 1.4 (PRECAUZIONI E INFOR-
MAZIONI GENERALI).
X Rimuovere le fiancatine, vedi 7.1.4 (RIMOZIONE
FIANCATINE LATERALI DESTRA E SINISTRA).
X Scollegare il connettore elettrico (12) (sul lato sinistro
10
del veicolo).
X Liberare il cablaggio dalla fascetta (13) di fissaggio.
Premunirsi di altra fascetta da utilizzare nel ri-
montaggio.
X + Svitare e togliere la vite (14).
X Svitare e togliere le due viti (15) recuperando le rondel-
le ed eventualmente i gommini.
Nel rimontaggio serrare le due viti (15) con
moderazione perch si fissano su materiale 16
plastico.
X Rimuovere il portatarga (16) completo di indicatori di 12
direzione posteriori, luce targa e fanale posteriore.
X Per rimuovere il fanale posteriore, vedi 7.1.22 (RIMO-
ZIONE FANALE POSTERIORE). 13 14
15
7 - 10
3$57(&,&/2 &+$66,63$576
7.1.5 DESMONTAJE PORTAEQUIPAJES TRASERO 7.1.5 REMOVING THE REAR LUGGAGE RACK
X Coloque el vehculo sobre el caballete. X Position the vehicle on the stand.
X Desmonte los paneles laterales, vase 7.1.4 (DES- X Remove the sides, see 7.1.4 (REMOVING THE
MONTAJE PANELES LATERALES DERECHO E IZ- RIGHT AND LEFT SIDES).
QUIERDO). X + Unscrew and remove the screw (1).
X + Destornille y quite el tornillo (1). Screw (1) driving torque: 10 Nm (1 kgm).
Par de apriete tornillo (1): 10 Nm (1kgm)
X Unscrew and remove the screw (2) and the two screws
X Destornille y quite el tornillo (2) y ambos tornillos (3). (3).
Par de apriete (2-3): 8 Nm (0,8 kgm) Screw (2-3) driving torque: 8 Nm (0.8 kgm).
X Quite el portaequipajes (4) y guarde los casquillos y X Remove the luggage rack (4) and take the bushes and
los elementos de goma. the rubber elements.
7.1.6 DESMONTAJE GRUPO GUARDABARROS 7.1.6 REMOVING THE FRONT MUDGUARD UNIT
DELANTERO
Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- TION) carefully.
CIONES GENERALES).
X Position the vehicle on the stand.
X Coloque el vehculo sobre el caballete.
7.1.7 DESMONTAJE SOPORTE PORTAMATRICULA 7.1.7 REMOVING THE NUMBER PLATE HOLDER
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
X Desmonte los paneles laterales, vase 7.1.4 (DES- X Remove the sides, see 7.1.4 (REMOVING THE
MONTAJE PANELES LATERALES DERECHO E IZ- RIGHT AND LEFT SIDES).
QUIERDO). X Disconnect the electric connector (12) (on the left side
X Desconecte el conector elctrico (12) (en la parte iz- of the vehicle).
quierda del vehculo). X Release the wiring from the fastening clamp (13).
X Suelte los cables de la abrazadera (13).
Get another clamp to be used for the reassem-
Prepare otra abrazadera para sustituir a la ori- bly.
ginal durante el montaje.
X Unscrew and remove the screw (14).
X + Destornille y quite el tornillo (14). X Unscrew and remove the two screws (15), taking the
X Destornille y quite los dos tornillos (15), guarde las washers and if necessary the rubber elements.
arandelas y, eventualmente, los elementos de goma.
Upon reassembly, tighten the two screws (15)
Durante el montaje apriete con cuidado y mo- moderately, since they are screwed onto plas-
deradamente los dos tornillos (15) en cuanto tic material.
se fijan en el material plstico.
X Remove the number plate holder (16) together with
X Desmonte el soporte portamatrcula (16) junto con los rear direction indicators, number plate light and rear
indicadores de direccin traseros, luz matrcula y faro light.
trasero. X To remove the rear light, see 7.1.22 (REMOVING THE
X Para desmontar el faro trasero vase 7.1.22 (DES- REAR LIGHT).
MONTAJE FARO TRASERO).
7 - 11
&,&/,67,&$
Nel rimontaggio assicurarsi del corretto posi-
zionamento dei componenti elettrici e dei rela-
tivi cablaggi.
7 - 12
3$57(&,&/2 &+$66,63$576
Durante el reensamblaje coloque correcta- Upon reassembly, make sure that the electric
mente los componentes elctricos y los ca- components and the relevant wiring are posi-
bles correspondientes. tioned correctly.
X + Destornille y quite el tornillo (10), guarde el casquillo X + Unscrew and remove the screw (10), take the bush
y, eventualmente, el elemento de goma. and if necessary the rubber element.
X Actuando desde la parte trasera con una llave tubular, X Acting on the lower part with a socket spanner, un-
destornille y quite el tornillo (11), guarde el casquillo y, screw and remove the screw (11), take the bush and if
eventualmente, el elemento de goma. necessary the rubber element.
X Baje el vano portadocumentos/kit herramientas (12) y X Lower the glove compartment (12) and remove it by
qutelo extrayndolo de la parte trasera. withdrawing it from the rear part.
7.1.9 DESMONTAJE PROTECTOR DE CARTER 7.1.9 REMOVING THE OIL PAN GUARD
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
X Destornille y quite los cuatro tornillos (13). X Unscrew and remove the four screws (13).
X Quite el protector de crter (14). X Remove the oil pan guard (14).
7 - 13
&,&/,67,&$
Provvedere affinch il serbatoio (11) del liquido
freno posteriore rimanga in posizione verticale
e non si rovesci con leventuale fuoriuscita di li-
quido.
12 14
Liberare tutti i cavi e i tubi dalle relative fascette
di fissaggio situate lungo il percorso.
Premunirsi poi di altrettante fascette da utilizza-
re nel rimontaggio.
7 - 14
3$57(&,&/2 &+$66,63$576
X + Quite el silenciador de escape izquierdo (4).
Plug the exhaust pipe openings, to avoid any
Trate que el depsito (11) del lquido del freno Make sure that the rear brake fluid tank (11)
trasero se mantenga en posicin vertical y remains in vertical position and does not
que no se vuelque porque podra salir el lqui- overturn, in order to avoid any outflow of
do. brake fluid.
Suelte todos los cables y los tubos de sus co- Release all the cables and pipes from the fas-
rrespondientes abrazaderas de bloqueo. tening clamps positioned along them.
Prepare el mismo nmero de abrazaderas Get other clamps to be used for the reassem-
para sustituirlas a las originales durante el reensam- bly.
blaje. X + Unscrew and remove the screw (12) and take the
X + Destornille y quite el tornillo (12) y guarde la arandela. washer.
Par de apriete tornillo (12): 25 Nm (2,5 kgm) Screw (12) driving torque: 25 Nm (2.5 kgm).
X + Unscrew and remove the screw (13) and take the
X + Destornille y quite el tornillo (13) y guarde la arandela.
washer.
Par de apriete tornillo (13): 25 Nm (2,5 kgm)
Screw (13) driving torque: 25 Nm (2.5 kgm).
X Quite el vstago del silln (14). X Remove the saddle pillar (14).
7 - 15
&,&/,67,&$
ZIONE SILENZIATORI DI SCARICO).
Premunirsi di fascetta stringitubo a cacciavi-
te, da sostituire alloriginale (di tipo speciale
senza vite).
X Tranciare la testa della fascetta stringitubo (1).
X Sfilare il tubo sfiato olio (2).
X Spostare la fascetta stringitubo (3).
X Sfilare il tubo (4) di drenaggio delle impurit.
X Spostare la fascetta stringitubo (5).
X Sfilare il tubo di scarico (6).
X Svitare e togliere la vite (7) liberando la fascetta (8).
X
Nel rimontaggio posizionare correttamente il
tubo di scarico (6) e la fascetta (8).
Sfilare i due tubi (4-6) dal collare sulla cassa filtro nella
parte inferiore.
X Allentare le due fascette (9-10).
X + Allentare di circa un giro la vite (11) di fissaggio infe-
riore reggisella.
Coppia di serraggio vite (11): 25 Nm (2,5 kgm)
X + Svitare e togliere la vite (12) di fissaggio superiore
reggisella e recuperare la rondella.
Coppia di serraggio vite (12): 25 Nm (2,5 kgm)
X Battere con il palmo della mano sul portapacchi fino
a che tutto il reggisella/cassa filtro non effettuer una
leggera rotazione (con fulcro in A) verso il basso per-
mettendo ai due manicotti (13-14) di liberarsi dai car-
buratori.
X
Non fare ruotare il gruppo reggisella / cassa
filtro oltre il necessario.
+ Serrare provvisoriamente la vite (11) in modo da
trattenere il gruppo reggisella in posizione.
13 14
17
7 - 16
3$57(&,&/2 &+$66,63$576
7.1.12 DESMONTAJE CAJA FILTRO 7.1.12 REMOVING THE AIR CLEANER CASING
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES) y 2.3 (BATERA). TION) and 2.3 (BATTERY) carefully.
X Coloque el vehculo sobre el caballete central - o X Position the vehicle on the centre stand - or on an
sobre un especial caballete de sostn fijado en los pi- apposite support stand fixed to the centre stand cou-
votes del caballete central. plings.
X Quite la batera, vase 7.1.13 (DESMONTAJE BATE- X Remove the battery, see 7.1.13 (REMOVING THE
RIA). BATTERY).
X Quite los silenciadores de escape, vase 7.1.10 (DES- X Remove the exhaust silencers, see 7.1.10 (REMOV-
MONTAJE SILENCIADORES DE ESCAPE). ING THE EXHAUST SILENCERS).
Prepare la abrazadera ajustable para sustituir- Get a screwdriver-type pipe clamp, to replace
la a la original (de tipo especial sin tornillo). the original one (special type without screw).
X Corte la cabeza de la abrazadera (1). X Cut the head of the pipe clamp (1).
X Extraiga el tubo de purga aceite (2). X Withdraw the oil breather pipe (2).
X Desplace la abrazadera (3). X Shift the pipe clamp (3).
X Extraiga el tubo (4) de drenaje de las impurezas. X Withdraw the impurities drain pipe (4).
X Desplace la abrazadera (5). X Shift the pipe clamp (5).
X Extraiga el tubo de escape (6). X Withdraw the exhaust pipe (6).
X Destornille y quite el tornillo (7) soltando la abrazadera X Unscrew and remove the screw (7), releasing the
(8). clamp (8).
Durante el reensamblaje coloque correcta-
mente el tubo de escape (6) y la abrazadera Upon reassembly, position the exhaust pipe
(8). (6) and the clamp (8) correctly.
X Extraiga los dos tubos (4-6) del collar de la parte infe- X Withdraw the two pipes (4-6) from the collar on the
rior de la caja de filtro. lower part of the air cleaner casing.
X Afloje las dos abrazaderas (9-10). X Loosen the two clamps (9-10).
X + Destornille de aproximadamente un giro el tornillo X + Loosen (about one turn) the screw (11) that fastens
(11) de sujecin inferior del vstago del silln. the lower part of the saddle pillar.
Par de apriete tornillo (11): 25 Nm (2,5 kgm) Screw (11) driving torque: 25 Nm (2.5 kgm).
X + Destornille y quite el tornillo (12) de sujecin supe- X + Unscrew and remove the screw (12) that fastens the
rior del vstago del silln y guarde la arandela. upper part of the saddle pillar and take the washer.
Par de apriete tornillo (12): 25 Nm (2,5 kgm) Screw (12) driving torque: 25 Nm (2.5 kgm).
X Golpee con la palma de la mano sobre el portaequipa- X Strike the luggage rack with the palm of your hand until
jes hasta que el grupo vstago del silln/caja del filtro the whole saddle pillar/filter casing unit performs a
realice una ligera rotacin (con fulcro en A) hacia slight downward rotation (with fulcrum in A), thus al-
abajo, de tal forma los dos manguitos (13-14) se suel- lowing the two couplings (13-14) to be released from
tan de los carburadores. the carburettors.
X
No gire el grupo vstago del silln/caja del fil-
tro ms de lo necesario.
+ Apriete provisionalmente el tornillo (11) para mante-
X
Do not make the saddle pillar/filter casing unit
rotate more than necessary.
+ Tighten the screw (11) temporarily, in such a way as
ner el grupo vstago del silln en posicin. to keep the saddle pillar unit in the right position.
7 - 17
&,&/,67,&$
Nel rimontaggio, verificare il corretto posizio-
namento delle sedi di accoppiamento sulla
cassa filtro (18) e sul portaoggetti (19).
X Rimuovere la cassa filtro (18) sfilandola come indicato
in figura.
Durante la rimozione muovere la cassa filtro
(18) ricercando la posizione migliore per lo sfi-
lamento.
X Ruotare e rimuovere il convogliatore aria (20) e pulire
lelemento filtrante, vedi 2.5 (FILTRO ARIA).
X Svitare e togliere le sette viti (21) e recuperare i relativi
dadi nella parte inferiore.
X Rimuovere il coperchio cassa filtro (22).
X Effettuare una accurata pulizia interna alla cassa filtro.
19
7.1.13 RIMOZIONE BATTERIA
Leggere attentamente 1.4 (PRECAUZIONI E INFOR-
MAZIONI GENERALI) e 2.3 (BATTERIA).
X Rimuovere la fiancatina sinistra, vedi 7.1.4 (RIMOZIO- 18
NE FIANCATINE LATERALI DESTRA E SINISTRA)). 18
X Svitare e togliere la vite (1).
X
Nel rimontaggio, serrare la vite (1) con mode-
razione perch si fissa su materiale plastico.
Rimuovere il coperchio batteria (2).
22 21
X Scollegare dal morsetto negativo () il cavo (3).
X Spostare la cuffia di protezione (4).
X Scollegare dal morsetto positivo (+) il cavo (5) e il cavo
(6) del rel di avviamento (colore rosso).
X Sfilare il tubo di sfiato (7).
21
Nel rimontaggio, collegare prima i cavi sul
morsetto positivo (+) e poi quello sul negativo
(). Infilare il tubo di sfiato (7).
X Piegare leggermente verso lesterno la batteria e ri-
muoverla dal suo alloggiamento sollevandola.
20
21
La batteria rimossa deve essere riposta in luo-
go sicuro e fuori dalla portata dei bambini.
4
6
3
5
7
1 2
7 - 18
3$57(&,&/2 &+$66,63$576
X Destornille los dos tornillos (15) y guarde las arande- X Unscrew and remove the two screws (15) and take the
las, el cablecito de enganche casco y, eventualmente, washers, the crash helmet cable and if necessary the
los elementos de goma y los casquillos. bushes and the rubber elements.
X Destornille y quite los dos tornillos (16) y guarde las X Unscrew and remove the two screws (16) and take the
correspondientes tuercas en la parte inferior. relevant nuts in the lower part.
X Destornille y quite el tornillo (17) y guarde las arande- X Unscrew and remove the screw (17), taking the wash-
las y, eventualmente, el elemento de goma. ers and if necessary the rubber element.
X Empuje hacia abajo (vase figura) la caja del filtro (18) X Press the filter casing (18) and the glove compartment
y el vano portadocumentos/kit herramientas (19) divi- (19) downwards (see figure), separating the two com-
diendo los dos componentes. ponents.
Durante el reensamblaje controle la perfecta Upon reassembly, make sure that the cou-
colocacin de las sedes de acoplamiento so- pling seats on the filter casing (18) and on the
bre la caja del filtro (18) y el vano portadocu- glove compartment (19) are positioned cor-
mentos/kit de herramientas (19). rectly.
X Quite la caja del filtro (18) extrayndola segn lo ilus- X Remove the filter casing (18), withdrawing it as indicat-
trado en figura. ed in the figure.
Durante el desmontaje desplace la caja del fil- During the removal, shift the filter casing (18),
tro (18) buscando la posicin mejor para ex- trying to find the best position to withdraw it.
traerla.
X Rotate and remove the air conveyor (20) and clean the
X Gire y quite el encauzador de aire (20) y limpie el ele- filtering element, see 2.5 (AIR CLEANER).
mento filtrante, vase 2.5 (FILTRO DEL AIRE). X Unscrew and remove the seven screws (21) and take
X Destornille y quite los siete tornillos (21) y guarde las the relevant nuts in the lower part.
correspondientes tuercas en la parte inferior. X Remove the filter casing cover (22).
X Quite la tapa de la caja del filtro (22). X Thoroughly clean the inside of the filter casing.
X Limpie con mucho cuidado el interior de la caja del fil-
tro.
Upon reassembly, tighten the screw (1) mod-
Durante el reensamblaje apriete con cuidado
erately, since it is screwed onto plastic mate-
y moderadamente el tornillo (1) en cuanto se
rial.
fija en el material plstico.
X Quite la tapa batera (2). X Remove the battery cover (2).
X Desconecte el cable (3) del terminal negativo (). X Disconnect the cable (3) from the negative terminal ().
X Desplace el elemento de proteccin (4). X Shift the protection element (4).
X Desconecte el cable (5) del terminal positivo (+) y el X Disconnect the cable (5) and the cable (6) of the start
cable (6) del rel de arranque (de color rojo). relay (red) from the positive terminal (+).
X Extraiga el tubo de purga (7). X Withdraw the breather pipe (7).
Durante el reensamblaje conecte antes los ca- Upon reassembly, first connect the cables on
bles al borne positivo (+) y luego al borne ne- the positive terminal (+) and then the cable on
gativo (). Introduzca el tubo de purga (7). the negative terminal (). Insert the breather
pipe (7).
X Incline apenas hacia el exterior la batera y extrigala
de su alojamiento levantndola. X Bend the battery slightly outwards and remove it from
its container by lifting it.
7 - 19
&,&/,67,&$
Operare con cautela.
Non danneggiare le linguette e/o le relative
sedi dincastro.
Maneggiare con cura i componenti verniciati, non
strisciarli o rovinarli. 3
X Divaricare moderatamente la carenatura nella sua par-
te inferiore e contemporaneamente spostarla legger-
mente in avanti.
X Scollegare il connettore elettrico (6) del fanale anterio-
re. 3
X + Scollegare i connettori elettrici indicatori di direzione
anteriori (7-8).
X Rimuovere la carenatura (9) completa di fanale (10),
indicatori di direzione anteriori (7-8) e mascherina
(11).
10
6
11 8
7 9
7 - 20
3$57(&,&/2 &+$66,63$576
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
X Quite el tablero de instrumentos, vase 7.1.17 (DES- X Remove the dashboard fairing, see 7.1.17 (DESMON-
MONTAJE TABLERO DE INSTRUMENTOS). TAJE TABLERO DE INSTRUMENTOS).
X + Destornille y quite los dos tornillos (1). X + Unscrew and remove the two screws (1).
X + Destornille y quite el tornillo (2). X + Unscrew and remove the screw (2).
X + Destornille y quite los dos tornillos (3). X + Unscrew and remove the two screws (3).
X Destornille y quite el tornillo (4) soltando la gua pasa- X Unscrew and remove the screw (4), releasing the ca-
cables (5) y, eventualmente, guarde el elemento de ble guide collar (5) and taking the rubber element if
goma. necessary.
Acte con cuidado. Proceed with care.
No dae las lengetas y/o los correspondien- Do not damage the tangs and/or the relevant
tes soportes de acoplamiento. seatings.
Maneje con cuidado los componentes barnizados Handle the painted components with care and avoid
para no rayarlos o daarlos. scraping or damaging them.
X Separe moderadamente el carenado en su parte infe- X Slightly separate the lower part of the front fairing and
rior y en el mismo tiempo desplcelo ligeramente ha- at the same time move it slightly forwards.
cia adelante. X Disconnect the electric connector (6) of the headlight.
X Desconecte el conector elctrico (6) del faro trasero. X + Disconnect the electric connector (7-8) of the front
X + Desconecte los conectores elctricos del los indica- direction indicator.
dores de direccin delanteros (7-8). X Remove the fairing (9) together with the headlight (10),
X Quite el carenado (9) junto con el faro (10), con los in- the front direction indicators (7-8) and the guard (11).
dicadores de direccin delanteros (7-8) y con el ele-
mento de proteccin (11). Upon reassembly, position the front fairing
correctly, making all the fastening and cou-
Al volverlo montar, coloque correctamente el pling points coincide.
carenado inferior as como todos los puntos
de acoplamiento y de sujecin coincidan perfecta- X If necessary, remove the headlight, see 7.1.15 (RE-
mente. MOVING THE HEADLIGHT) and the direction indica-
tors, see 7.1.30 (REMOVING THE FRONT DIREC-
X Quite, eventualmente, el faro delantero, vase 7.1.15 TION INDICATORS).
(DESMONTAJE FARO DELANTERO) y los indicado-
res de direccin, vase 7.1.30 (DESMONTAJE INDI-
CADORES DE DIRECCION DELANTEROS).
7 - 21
&,&/,67,&$
X
Nel rimontaggio serrare le viti (1) con modera-
zione perch si fissano su materiale plastico.
Rimuovere il gruppo fanale anteriore (2).
X
Maneggiare con cura i componenti verniciati,
non strisciarli o rovinarli.
Rimuovere la plancia strumenti (17) sollevandola.
11 10
12
7 - 22
3$57(&,&/2 &+$66,63$576
Durante el reensamblaje apriete con cuidado Upon reassembly, tighten the screws (1) mod-
y moderadamente los tornillos (1) en cuanto erately, since they are screwed onto plastic
se fijan en el material plstico. material.
X Desmonte el grupo faro delantero (2). X Remove the headlight unit (2).
Handle the painted components with care and avoid
Maneje con cuidado los componentes barni- scraping or damaging them.
zados para no rayarlos o daarlos.
X Remove the dashboard fairing (17), by lifting it.
X Quite el tablero de instrumentos (17) levantndolo.
7 - 23
&,&/,67,&$
RIMOZIONE CONTAGIRI
X Scollegare il rinvio contagiri (1).
X Sfilare dalla sua sede la lampadina di illuminazione
(2).
X Allentare e togliere i due dadi (3), recuperare le rondel-
le ed eventualmente i gommini.
X Sfilare dal suo alloggiamento il contagiri.
Per agevolare lo sfilamento dello strumento,
ruotare il rinvio ricercando la posizione pi fa-
vorevole.
RIMOZIONE TACHIMETRO/CONTACHILOMETRI
X Allentare e togliere la ghiera (4).
X Spingere fuori dalla sua sede il pomello azzerratore
(5).
X Scollegare il rinvio tachimetro/contachilometri (6).
X Sfilare dalla sua sede la lampadina di illuminazione
(7).
X Allentare e togliere i due dadi (8), recuperare le rondel-
le ed eventualmente i gommini.
X Sfilare dal suo alloggiamento il tachimetro/contachilo-
metri.
Per agevolare lo sfilamento dello strumento,
ruotare il rinvio ricercando la posizione pi fa-
vorevole.
X
Contrassegnare i connettori per ricollegarli
successivamente nella giusta posizione.
Scollegare i tre connettori elettrici (9).
X Sfilare dalla sua sede la lampadina di illuminazione
(10).
X Allentare e togliere il dado (11), recuperare la rondella
ed eventualmente il gommino.
X Sfilare dal suo alloggiamento lindicatore temperatura
liquido refrigerante.
7 - 24
3$57(&,&/2 &+$66,63$576
X Extraiga de su alojamiento el cuentarrevoluciones.
To facilitate the removal of the instrument,
Para facilitar la extraccin del instrumento
turn the control trying to find the most con-
gire la transmisin buscando la posicin ms
venient position.
favorable.
DESMONTAJE REMOVING
VELOCIMETRO/CUENTAKILOMETROS THE SPEEDOMETER/ODOMETER
X Afloje y quite la tuerca (4). X Loosen and remove the metal ring (4).
X Empuje fuera de su alojamiento el pomo de ajuste del X Push the control knob (5) out of its seat.
cero (5). X Disconnect the speedometer/odometer control (6).
X Desconecte la transmisin velocmetro/cuentakilme- X Withdraw the bulb (7) from its seat.
tros (6).
X Loosen and remove the two nuts (8), take the washers
X Extraiga de su alojamiento la bombilla de iluminacin
and if necessary the rubber elements.
(7).
X Withdraw the speedometer/odometer from its housing.
X Afloje y quite las dos tuercas (8), guarde las arandelas
y, eventualmente, los elementos de goma. To facilitate the removal of the instrument,
X Extraiga de su alojamiento el velocmetro/cuentakil- turn the control trying to find the most con-
metros. venient position.
Para facilitar la extraccin del instrumento
gire la transmisin buscando la posicin ms
favorable.
X
Marque los conectores para volver a conec-
tarlos en su posicin correcta.
Desconecte los tres conectores elctricos (9).
X
Mark the connectors, in order to be able to re-
connect them in the right position.
Disconnect the three electric connectors (9).
X Extraiga de su alojamiento la bombilla de iluminacin X Withdraw the bulb (10) from its seat.
(10). X Loosen and remove the nut (11), take the washer and
X Afloje y quite la tuerca (11), guarde la arandela y, if necessary the rubber element.
eventualmente, el elemento de goma. X Withdraw the coolant temperature indicator from its
X Extraiga de su alojamiento el indicador temperatura l- housing.
quido refrigerante.
7 - 25
&,&/,67,&$
1
Premunirsi di altrettante fascette da utilizzare 6
nel rimontaggio.
7 - 26
3$57(&,&/2 &+$66,63$576
X Suelte los cables de todas las abrazaderas (siete). X Release the cables from all the fastening clamps (sev-
en).
Prepare el mismo nmero de abrazaderas
para sustituirlas a las originales durante el Get other clamps to be used for the reassem-
reensamblaje. bly.
X Desconecte los seis conectores elctricos (1). X Disconnect the six electric connectors (1).
X Extraiga el rel luces largas (2) de su propio engan- X Withdraw the high beam relay (2) from its coupling.
che. X Unscrew and remove the screw (3), releasing the sup-
X Destornille y quite el tornillo (3) soltando el soporte (4) port (4) of the electric connectors.
de sostn conectores elctricos. X Loosen and remove the two nuts (5) and withdraw the
X Afloje y quite las dos tuercas (5) y extraiga los corres- corresponding screws from the opposite side.
pondientes tornillos del lado opuesto. X Remove the dashboard support (6).
X Quite el soporte salpicadero (6).
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
X Quite el carenado delantero, vase 7.1.14 (DESMON- X Remove the front fairing, see 7.1.14 (REMOVING THE
TAJE CARENADO DELANTERO). FRONT FAIRING).
X Suelte los cables de las dos abrazaderas (7-8). X Release the wiring from the two fastening clamps (7-
8).
Prepare el mismo nmero de abrazaderas
para sustituirlas a las originales durante el Get other clamps to be used for the reassem-
reensamblaje. bly.
beza.
Durante el reensamblaje utilice un tornillo del
mismo tipo, apretndolo hasta romper la ca-
off.
For the reassembly, use another screw of the
same type, tightening it until the head comes
X Quite el interruptor de encendido/seguro de direccin X Remove the ignition switch/steering lock (12) by with-
(12) soltndolo desde abajo y guarde el arco guaca- drawing it from below and take the cable guide arch
bles (13). (13).
7 - 27
&,&/,67,&$
Nel rimontaggio serrare le due viti (6) con mo-
derazione perch si fissano su materiale pla-
stico.
Sul lato destro del manubrio, la vite anteriore pi
corta.
Contrassegnare i connettori elettrici per ri-
collegarli successivamenti nella corretta posi-
zione.
X Scollegare i connettori elettrici.
X Rimuovere il fanale posteriore (12).
7 - 28
3$57(&,&/2 &+$66,63$576
X + Destornille y quite los dos tornillos (6). X + Unscrew and remove the two screws (6).
Durante el reensamblaje apriete con cuidado Upon reassembly, tighten the two screws (6)
y moderadamente los tornillos (6) en cuanto moderately, since they are screwed onto plas-
se fijan en el material plstico. tic material.
En el lado derecho del manillar el tornillo delantero On the right side of the handlebars the front screw is
es ms corto. shorter.
X + Separe los dos semicascos (8-9). X + Separate the two half-shells (8-9).
X Desconecte el cable acelerador (7) (en el lado izquier- X Disconnect the accelerator cable (7) (withdraw the
do del manillar extraiga el cable de encendido en fro). cold start cable on the left side of the handlebars).
X Extraiga el tubo mando acelerador (4) (en el lado iz- X Withdraw the accelerator control tube (4) (take the cold
quierdo del manillar guarde el mando de encendido en start control on the left side of the handlebars).
fro).
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
X Desmonte los paneles laterales, vase 7.1.4 (DES- X Remove the sides, see 7.1.4 (REMOVING THE
MONTAJE PANELES LATERALES DERECHO E IZ- RIGHT AND LEFT SIDES).
QUIERDO). X + Unscrew and remove the nut (10), take the washer
X + Destornille y quite la tuerca (10), guarde la arandela and if necessary the bush and the rubber element.
y, eventualmente, el casquillo y el elemento de goma. X Working under the glove compartment with a socket
X Actuando por debajo del vano portadocumentos/kit de spanner, unscrew and remove the nut (11), take the
herramientas con una llave tubular, destornille y quite washer and if necessary the bush and the rubber ele-
la tuerca (11), guarde la arandela y, eventualmente el ment.
casquillo y el elemento de goma. X Shift the rear light (12) slightly backwards.
X Desplace un poco atrs el faro trasero (12).
7 - 29
&,&/,67,&$
Se la catena risulta particolarmente usurata, 4
sostituirla assieme al pignone trasmissione,
vedi 7.1.24 (RIMOZIONE ROTELLE E PATTINO
CATENA) e alla corona, vedi 7.3 7.3 (RUOTA POSTE-
RIORE).
RIMOZIONE PATTINO
X Rimuovere il carter protezione pignone trasmissione,
vedi 3.1.3 (RIMOZIONE CARTER PROTEZIONE PI-
GNONE TRASMISSIONE).
X Rimuovere lanello di arresto (10).
X Sfilare dallalbero il pignone trasmissione (11) comple-
to di catena.
Se loperazione di sfilamento del pignone tra-
smissione (11) risulta difficoltosa, allentare
moderatamente la tensione della catena, vedi 2.16.3
(REGOLAZIONE).
X Rimuovere il pignone trasmissione (11).
Nel rimontaggio, applicare sulla dentatura in-
terna del pignone di trasmissione (11) LOCTI-
TE Anti-Seize.
X Svitare e togliere le due viti (12).
X Infilare un cacciavite nellapposito foro (13).
X Rimuovere il pattino (14) sfilandolo dalla parte anterio-
re.
7 - 30
3$57(&,&/2 &+$66,63$576
If the chain is excessively worn, change it to-
Si la cadena est muy desgastada, sustityala gether with the transmission pinion, see
junto con el pin de transmisin, vase 7.1.24 (REMOVING THE CHAIN ROLLERS AND
7.1.24 (DESMONTAJE RODILLOS Y PATIN CA- THE CHAIN SHOE), and with the crown gear, see 7.3
DENA) y con la corona, vase 7.3 (RUEDA TRASE- (REAR WHEEL).
RA).
7.1.24 DESMONTAJE RODILLOS Y PATIN CADENA 7.1.24 REMOVING THE CHAIN ROLLERS AND THE
CHAIN SHOE
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA-
CIONES GENERALES). Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
TION) carefully.
X Guarde las dos arandelas, el rodillo (9) y el casquillo X Take the two washers, the roller (9) and the special
distanciador especial (material plstico + metal). spacing bush (plastic + metal).
X Extraiga del eje el pin de transmisin (11) junto con X Withdraw the transmission pinion (11) complete with
la cadena. chain from the shaft.
Si la operacin de extraccin del pin de It it is difficult to withdraw the transmission
transmisin (11) resulta algo difcil, afloje un pinion (11), slightly slacken the chain, see
poco la tensin de la cadena, vase 2.16.3 (AJUSTE). 2.16.3 (ADJUSTMENT).
X Quite el pin de transmisin (11). X Remove the transmission pinion (11).
Durante la instalacin aplique sobre el denta- Upon reassembly, apply LOCTITE Anti-Seize
do interior del pin de transmisin (11) LOC- on the inner toothing of the transmission pi-
TITE Anti-Seize. nion (11).
X Destornille y quite los dos tornillos (12). X Unscrew and remove the two screws (12).
X Inserte un destornillador en el correspondiente hueco X Insert a screwdriver in the apposite hole (13).
(13). X Remove the shoe (14) by withdrawing it from the front
X Quite el patn (14) extrayndolo del lado delantero. part.
7 - 31
&,&/,67,&$
3 5 4
X
Operare con il cavalletto in posizione di ripo-
so.
Scollegare le due molle (7).
X + Allentare e togliere il dado (8).
X + Sfilare la vite (9).
Coppia di serraggio dado/vite (8-9): 80 Nm (8 kgm)
X Rimuovere il cavalletto (10).
7 - 32
3$57(&,&/2 &+$66,63$576
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
X Coloque el vehculo sobre el caballete central - o X Position the vehicle on the centre stand - or on an
bien sobre un especial caballete de sostn fijado a los apposite support stand fixed to the centre stand cou-
ataques del caballete central. plings.
X Desconecte los dos resortes (1). X Disconnect the two springs (1).
X Afloje y quite la tuerca (2) y guarde la arandela. X Loosen and remove the nut (2) and take the washer.
Par de apriete tuerca (2): 30 Nm (3 kgm) Nut (2) driving torque: 30 Nm (3 kgm).
X Destornille y quite el tornillo (4). X Unscrew and remove the screw (4).
X Extraiga el interruptor (3). X Withdraw the switch (3).
X Extraiga el perno (5). X Withdraw the pin (5).
X Quite el caballete (6). X Remove the stand (6).
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
X Coloque el vehculo sobre el caballete lateral. X Position the vehicle on the side stand.
X
Acte con el caballete en posicin de reposo.
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
7 - 33
&,&/,67,&$
Nel rimontaggio posizionare alla giusta altez-
za la leva comando freno anteriore e la leva
comando frizione. 5
11
12 10
7 - 34
3$57(&,&/2 &+$66,63$576
(1).
Prepare el mismo nmero de abrazaderas
para sustituirlas a las originales durante el Get other clamps to be used for the reassem-
reensamblaje. bly.
X + Destornille y quite los dos tornillos (2). X + Unscrew and remove the two screws (2).
X + Quite el semicasco (3) junto con el retrovisor. X + Remove the half-shell (3) complete with the rear-
X Desplace el semicasco (4) junto con la palanca de view mirror.
mando embrague (en el lado derecho bomba/palanca X Shift the half-shell (4) complete with the clutch control
de mando freno delantero). lever (on the right side of the front brake lever/pump).
X + Quite el elemento de goma de proteccin (5). X + Remove the rubber protection element (5).
X + Destornille y quite los dos tornillos (6). X + Unscrew and remove the two screws (6).
Par de apriete tornillos (6): 25 Nm (2,5 kgm) Screw (6) driving torque: 25 Nm (2.5 kgm).
X + Quite el perno de U (7). X + Remove the U-bolt (7).
X Quite el manillar (8). X Remove the handlebars (8).
Durante el reensamblaje coloque a la altura Upon reassembly, position the front brake le-
correcta la palanca de mando freno delantero ver and the clutch control lever at the right
y la palanca de mando embrague. height.
Despus del reensamblaje ajuste, si es necesario, el re- After the reassembly, if necessary adjust the mirror:
trovisor: X + Loosen the nut (12).
X + Afloje unos giros la tuerca (12). X + Turn the mirror (11) to its optimal position.
X + Gire el retrovisor (11) en la posicin ms adecuada. X + Tighten the nut (12).
X + Apriete la tuerca (12). X + Put back the protection element (9).
X + Vuelva a Colocar el elemento de proteccin (9).
7 - 35
&,&/,67,&$
Nel riassemblaggio, serrare con cautela e mo-
deratamente la vite (3) onde evitare di danneg-
giare il vetro protettivo.
Nel riassemblaggio riposizionare corretta-
mente la bussola (10) nella sede supporto in-
dicatore.
11
7.1.32 RIMOZIONE SERRATURA SELLA
X Rimuovere la sella, vedi 7.1.3 (RIMOZIONE SELLA).
X Svitare e togliere le due viti (11). 12
X Rimuovere la serratura sella (12).
7 - 36
3$57(&,&/2 &+$66,63$576
Durante el reensamblaje apriete el tornillo (1)
moderadamente en cuanto se fija en el mate- Upon reassembly, tighten the screw (1) mod-
rial plstico. erately, since it is screwed onto plastic materi-
al.
X + Quite el indicador de direccin (2) completo.
X + Remove the whole direction indicator (2).
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Carefully read 1.4 (PRECAUTIONS AND GENERAL IN-
CIONES GENERALES). FORMATION).
Durante el reensamblaje apriete con cuidado Upon reassembly, tighten the screw (3) care-
y moderadamente el tornillo (3) para no daar fully, without exerting too much pressure, in
el cristal de proteccin. order to avoid damaging the glass protection
cover.
Durante el reensamblaje coloque correcta-
mente el casquillo (10) en el alojamiento so-
porte indicador. Upon reassembly, correctly position the bush
(10) in the indicator support seat.
7.1.32 DESMONTAJE BLOQUEO CIERRE SILLIN 7.1.32 REMOVING THE SADDLE LOCK
X Desmonte el silln, vase 7.1.3 (DESMONTAJE SI- X Remove the saddle, see 7.1.3 (REMOVING THE SAD-
LLIN). DLE).
X Destornille y quite los dos tornillos (11). X Unscrew and remove the two screws (11).
X Quite el bloque cierre silln (12). X Remove the saddle lock (12).
7 - 37
&,&/,67,&$
La rimozione del telaio deve essere effettuata
solo in un Centro Autorizzato o da un Conces-
sionario Ufficiale DSULOLD.
Loperazione di rimozione del telaio partico-
larmente complessa, pertanto prima di proce-
dere necessario visionare con molta atten-
zione il veicolo.
Non svitare o comunque manomettere per
nessun motivo le due viti e relativi dadi di
unione telaio (vedi figura).
Apporre dei contrassegni su cavi e tubi per
evitare lo scambio nel rimontaggio.
Per ulteriori informazioni sul percorso dei cavi
e dei tubi, vedi 8.2 (PERCORSO, FISSAGGIO, CA-
BLAGGIO, CAVI E TUBI).
Liberare i cavi e i tubi dalle linguette sul telaio
e sul supporto superiore ammortizzatore e sfi-
larli dai collari sui componenti che si andran-
no a rimuovere.
Liberare tutti i cavi dalle relative fascette di
fissaggio situate lungo il percorso.
Premunirsi di altrettante fascette da utilizzare
nel rimontaggio.
7 - 38
3$57(&,&/2 &+$66,63$576
El desmontaje del bastidor tiene que ser efec- The frame must be removed only by an au-
tuado exclusivamente por un Centro Autoriza- thorized centre or by an DSULOLD Official Deal-
do o por un Concesionario Oficial DSULOLD. er.
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION)carefully.
El desmontaje del bastidor es particularmente The removal of the frame is particularly diffi-
complejo, por eso antes de seguir con esta cult to carry out, therefore it is necessary to
operacin es necesario examinar con mucho check the vehicle carefully before proceeding
cuidado el vehculo. to this operation.
En este captulo los procedimientos estn detallados This chapter describes the relevant procedures pro-
en orden progresivo secuencial. gressively and in sequential order.
Una eventual sobreposicin de las operaciones por Any coincidence of operations in the references to
efecto de las remisiones a otros captulos tiene que other chapters must be understood according to a
interpretarse en sentido lgico, para evitar desmon- logic principle, in order to avoid the unnecessary re-
tajes no necesarios de otros componentes. moval of certain components.
No destornille o manipule por ninguna razn Neither unscrew, nor tamper with the two
los dos tornillos de unin del bastidor y las screws and the relevant nuts that fasten the
tuercas correspondientes (vase figura). frame for any reason whatsoever (see figure).
X Desmonte el motor, vase 3.2 (EXTRACCION DEL X Remove the engine, see 3.2 (REMOVING THE EN-
MOTOR DEL BASTIDOR) y 3.3 (INSTALACION MO- GINE FROM THE FRAME) and 3.3 (REINSTALLING
TOR SOBRE BASTIDOR). THE ENGINE ON THE FRAME).
X Destornille y quite el tornillo (1). X Unscrew and remove the screw (1).
X Quite la proteccin (2). X Remove the guard (2).
X Desconecte los conectores elctricos en el lado iz- X Disconnect the electric connectors on the left side of
quierdo del vehculo. the vehicle.
Marque los cables y los tubos para volver a Mark cables and pipes to avoid confusing
colocarlos correctamente durante el reensam- them during the reassembly.
blaje. Para mayores informaciones sobre el For further information on the lines of cables
recorrido de los cables y de los tubos vase 8.2 (RE- and pipes, see 8.2 (LINES, FIXING, HARNESS OF CA-
CORRIDO, SUJECION, CABLEADO, CABLES Y TU- BLES AND PIPES).
BOS).
Release the cables and pipes from the tangs
Suelte los cables y los tubos de las lengetas positioned on the frame and on the shock ab-
en el bastidor y en el soporte superior amorti- sorber upper support and withdraw them from
guador y qutelos de los collares en los com- the collars positioned on the components that must
ponentes que va a desmontar. be removed.
X Desconecte los conectores elctricos en el interruptor
X Disconnect the electric connectors positioned on the
de la bomba freno trasero.
switch of the rear brake pump.
X Desmonte el vstago del silln junto con la caja del fil-
X Remove the saddle pillar complete with filter casing
tro con batera, estribo pasajero, portaequipajes, vano
and battery, passengers footrest, luggage rack, glove
portadocumentos/kit de herramientas, soporte porta-
compartment, number plate holder with rear light and
matrcula con faro trasero y silenciadores de escape,
exhaust silencers, see 7.1.11 (REMOVING THE SAD-
vase 7.1.11 (DESMONTAJE VASTAGO SILLIN) (a
DLE PILLAR) (from point nine onwards).
partir del punto 9 en adelante).
tuirlas a las originales durante el reensamblaje.
Get screwdriver-type pipe clamps, to replace the
Prepare la abrazadera ajustable para susti-
original ones (special type without screw).
tuirla a la original (de tipo especial sin torni-
llo).
X Cut the heads of the pipe clamps (3-4-5) in the given
X Corte segn el orden la cabeza de las abrazaderas (3- order.
4-5). X Withdraw first the oil breather pipe (6) and then the en-
X Extraiga segn el orden el tubo de purga aceite (6) y gine oilpipes (7-8).
los tubos aceite motor (7-8). X Release the start relay (9) from its coupling.
X Suelte de su propio enganche el rel de encendido (9). X Disconnect the electric connector (10).
X Desconecte el conector elctrico (10). X Unscrew and remove the two screws (11).
X Destornille y quite los dos tornillos (11). X Remove the H.T. coil (12).
X Extraiga la bobina AT (12).
7 - 39
&,&/,67,&$
Le fasce e il paranco devono essere adeguati
a sostenere in tutta sicurezza il telaio comple-
to di avantreno.
7 - 40
3$57(&,&/2 &+$66,63$576
X Extraiga el basculante junto con la rueda, grupo sus- X Remove the rear fork complete with wheel, suspension
pensin y grupo freno , vase 7.9.1 (DESMONTAJE). unit and brake unit, see 7.9.1 (REMOVAL).
X Desmonte el pedal freno trasero, vase 7.1.24 (DES- X Remove the rear brake pedal, see 7.1.24 (REMOVING
MONTAJE RODILLOS Y PATIN CADENA). THE CHAIN ROLLERS AND THE CHAIN SHOE).
X Quite el soporte salpicadero, vase 7.1.19 (DESMON- X Remove the dashboard support, see 7.1.19 (REMOV-
TAJE SOPORTE SALPICADERO). ING THE DASHBOARD SUPPORT).
X Suspenda el bastidor como indicado en la figura y en- X Sling the engine as indicated in the figure and hook the
ganche las cintas a un aparejo de sujecin. bands to a hoist for support.
Las cintas y el aparejo de sujecin tienen que The bands and the hoist must be suitable for
ser adecuados para sostener en toda seguri- bearing the weight of the frame, complete with
dad el bastidor junto con el tren delantero. forecarriage in total safety.
X Levante el bastidor junto con el avantrn (rueda + X Lift the frame, complete with forecarriage (wheel +
guardabarros + manillar con mandos) lo suficiente mudguard + fork + handlebars with controls) as much
para tener un espacio de unos 250 mm entre la rueda as necessary to have a distance of about 250 mm be-
y el suelo. tween the wheel and the ground.
X Extraiga el tren delantero (13) junto con el manguito de X Withdraw the whole forecarriage (13) from the steering
direccin (14), vase 7.7 (DIRECCION). tube (14), see 7.7 (STEERING).
X + Destornille y quite el tornillo (15) y guarde las dos X + Unscrew and remove the screw (15) and take the
arandelas. two washers.
Par de apriete tornillo (15): 50 Nm (5 kgm) Screw (15) driving torque: 50 Nm (5 kgm).
X + Destornille y quite el tornillo (16) y guarde la arande- X + Unscrew and remove the screw (16) and take the
la. washer.
Par de apriete tornillo (16): 50 Nm (5 kgm) Screw (16) driving torque: 50 Nm (5 kgm).
X Quite el soporte superior amortiguador (17). X Remove the shock absorber upper support (17).
X + Destornille y quite el tornillo (18). X + Unscrew and remove the screw (18).
Par de apriete tornillo (18): 80 Nm (kgm) Screw (18) driving torque: 80 Nm (8 kgm).
X Guarde el estribo piloto y el soporte biela doble (19) X Take the riders footboard and the double connecting
junto con el eventual caballete central -. rod support (19) complete with the centre stand -, if
X Destornille y quite el tapn del aceite (20) y guarde la this is provided.
junta trica (21). X Unscrew and remove the oil plug (20) and take the O-
X Destornille y quite el filtro aceite (22) y guarde la junta ring (21).
(23). X Unscrew and remove the oil filter (22) and take the
Par de apriete filtro aceite (22): 35 Nm (3,5 kgm) gasket (23).
X Destornille y quite el tapn de escape aceite (24) y Oil filter (22) driving torque: 35 Nm (3.5 kgm).
guarde la arandela estanca (25). X Unscrew and remove the oil drain plug (24) and take
Par de apriete tapn de escape aceite: the sealing washer (25).
27 Nm (2,7 kgm) Oil drain plug (24) driving torque: 27 Nm (2.7 kgm).
X Destornille y quite el tornillo (26) y guarde el tampn X Unscrew and remove the screw (26) and take the buff-
(27). er (27).
X Afloje y quite la tuerca, extraiga el tornillo y guarde la X Loosen and remove the nut, withdraw the screw and
arandela y las dos placas de sujecin motor (28). take the washer and the two engine support plates
Par de apriete tornillo/tuerca de sujecin placas (28).
motor (28): 25 Nm (2,5 kgm). Driving torque of the engine support plate (28) fas-
tening screw/nut: 25 Nm (2.5 kgm).
Al final del reensamblaje del bastidor siga ejecutando es- Once the frame has been completely reinstalled, proceed
tas operaciones: to the following operations:
X Controle y, eventualmente, ajuste el juego de los coji- X Check and if necessary adjust the steering bearing
netes de direccin, vase 2.24.1 (CONTROL JUEGO slacks, see 2.24.1 (CHECKING THE BEARING
COJINETES) y 2.24.2 (AJUSTE JUEGO COJINE- SLACKS) and 2.24.2 (ADJUSTING THE BEARING
TES). SLACKS).
X Controle y, eventualmente, ajuste el basculante, va- X Check and if necessary adjust the rear fork, see 2.26
se 2.26 (HORQUILLA TRASERA) y 2.26.1 (AJUSTE (REAR FORK) and 2.26.1 (ADJUSTING THE REAR
BASCULANTE). FORK).
X Controle la correcta colocacin y la sujecin de los tu- X Make sure that pipes and cables are correctly posi-
bos y de los cables. tioned and fastened.
X Controle la correcta colocacin del pedal freno trasero, X Make sure that the rear brake pedal is positioned cor-
vase2.20 (AJUSTE DEL PEDAL DEL FRENO TRA- rectly, see 2.20 (REAR BRAKE PEDAL ADJUST-
SERO). MENT).
7 - 41
&,&/,67,&$
5827$$17(5,25(
Causa il peso e l'ingombro del veicolo, l'ope-
8) Ruota completa
razione che segue richiede l'intervento di un
9) Distanziale esterno secondo operatore.
Procedere con cautela e assicurarsi di poter sostene-
re il peso del veicolo.
Q = GRASSO, vedi 1.7 (TABELLA LUBRIFICANTI). Peso a vuoto del veicolo (in ordine di marcia):
200 kg.
X Sollevare la parte anteriore e far sistemare un adegua-
to supporto (con altezza 350 mm) sotto il motore, in
modo tale che la ruota anteriore abbia libero spazio di
movimento e il veicolo sia assicurato contro la caduta.
Pericolo di caduta del veicolo.
Provvedere al bilanciamento del veicolo per
impedirne la caduta.
X Posizionare e fissare un peso di circa 40 kg sul porta-
pacchi posteriore per sostenere la parte anteriore del
veicolo.
7 - 42
3$57(&,&/2 &+$66,63$576
Q = GRASA, vase 1.7 (TABLA DE LOS LUBRICAN- Q = GREASE, see 1.7 (LUBRICANT CHART).
TES).
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES) y 2.28 (RUEDA DELANTERA). TION) and 2.28 (FRONT WHEEL) carefully.
X Coloque el vehculo sobre el caballete central - o X Position the vehicle on the centre stand - or on an
bien sobre un especial caballete de sostn fijado en apposite support stand fixed to the centre stand cou-
los pivotes del caballete central. plings.
X Desmonte el protector de crter, vase 7.1.9 (DES- X Remove the oil pan guard, see 7.1.9 (REMOVING
MONTAJE PROTECTOR DE CARTER). THE OIL PAN GUARD).
A causa del peso y del espacio que ocupa el Due to the weight and dimensions of the vehi-
vehculo la operacin que sigue a continua- cle, the following operation cannot be per-
cin necesita la intervencin de un segundo formed by one person only.
operador. Siga adelante con cuidado y compruebe si Proceed with care and make sure that you can sup-
puede soportar el peso del vehculo. port the weight of the vehicle.
X Levante la parte delantera y coloque un soporte ade- X Raise the front part of the vehicle and have a suitable
cuado (con altura 350 mm) por debajo del motor, de support (the height of which should be about 350 mm)
manera que la rueda delantera tenga espacio suficien- placed under the engine, so that the front wheel can
te para moverse libremente y para evitar la cada del rotate freely and the vehicle cannot fall down.
vehculo.
The vehicle may fall down.
Peligro de cada del vehculo. Provide for balancing the vehicle, in order to
Provea a equilibrar el vehculo para que no prevent it from falling down.
caiga.
X Position and fix a load weighing about 40 kg on the
X Ponga y sujete un peso de unos 40 kg sobre el portae- rear luggage rack, in order to support the front part of
quipajes trasero para soportar la parte delantera del the vehicle.
vehculo.
7 - 43
&,&/,67,&$
Non azionare la leva del freno anteriore dopo
aver rimosso la ruota, altrimenti i pistoncini
della pinza potrebbero fuoriuscire dalle sedi,
causando la perdita del liquido freni.
Nel rimontaggio utilizzare, per l'inserimento
dei cuscinetti, un tampone con diametro
uguale all'anello esterno dei cuscinetti.
I componenti devono essere rimontati dal lato oppo-
sto disco freno assicurandosi che il cuscinetto (12)
vada perfettamente in battuta.
7 - 44
3$57(&,&/2 &+$66,63$576
X Bloquee el manillar en posicin de marcha de manera X Have the handlebars held still in driving position, so
que la direccin quede bloqueada. that the steering is locked.
X Afloje los dos tornillos (1) de la brida del eje de la rue- X Loosen the two screws (1) of the wheel pin clamp.
da. X Unscrew and remove the two screws (2).
X Destornille y saque los dos tornillos (2). X Move the mudguard support (3) as much as necessary
X Desplace suficientemente el soporte guardabarros (3) and unscrew the wheel pin (4).
y desenrosque el eje de la rueda (4).
To facilitate the extraction of the wheel pin,
Para facilitar la extraccin del eje de la rueda, slightly raise the wheel.
levante moderadamente la rueda.
X Extract the wheel pin (4) manually.
X Extraiga manualmente el eje de la rueda (4). X Take the spacer (5) (left side).
X Guarde el distanciador (5) (lado izquierdo).
Upon removal, check the position of the
Durante el desmontaje controle la posicin speedometer/odometer control: it will be use-
del mando velocmetro/cuentakilmetros, le ful during the reassembly.
resultar til para volver a instalarlo correctamente.
X Remove the speedometer/odometer control (6) from
X Desmonte el reenvo velocmetro/cuentakilmetros (6) the wheel seat, taking the control sealing ring (7) and
del alojamiento de la rueda guardando el anillo de jun- the traction ring (8).
ta transmisin (7) y el anillo de arranque (8). X Remove the wheel, carefully withdrawing the disc from
X Extraiga la rueda poniendo cuidado al sacar el disco the brake caliper.
de la pinza del freno.
Never pull the front brake lever after removing
No accione la palanca del freno delantero tras the wheel, otherwise the caliper pins may go
haber extrado la rueda porque en caso con- out of their seats, thus causing the outflow of
trario los mbolos de la pinza del freno po- the brake fluid.
dran salirse de sus alojamientos, causando la prdi-
da del lquido de los frenos.
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 carefully (PRECAUTIONS AND GENERAL
CIONES GENERALES). INFORMATION).
The bearings must be checked and if neces-
Despus de cada desmontaje controle los co- sary changed every time they are disassem-
jinetes y, si es necesario, sustityalos. bled.
X Con un trapo limpie los dos lados del cubo. X Clean both sides of hub with a clean cloth.
X Golpear sobre una herramienta adecuada (que tenga X Hit against a suitable punch (with diameter equal to the
un dimetro igual al anillo interior de los cojinetes) inner ring of the bearings) resting on the inner ring of
apoyada contra el anillo interior del cojinete de la iz- the left bearing.
quierda, empuje hacia afuera, en el siguiente orden: el Push out the following parts in the given order: the seal
retn (9), el cojinete derecho (10), el distanciador inte- (9), the right bearing (10), the inner spacer (11), and
rior (11) y el cojinete izquierdo (12). the left bearing (12).
X Limpie muy bien el interior del cubo. X Thoroughly clean the inside of the hub.
Para montar nuevamente los cojinetes, utilice Upon reassembly, to insert the bearings use a
una herramienta con dimetro igual al anillo punch with diameter equal to the outer ring of
exterior de los cojinetes. the bearings.
Los componentes deben montarse del lado contrario The components must be reassembled from the op-
al disco de freno, controlando que el cojinete (12) posite side of the brake disc, making sure that the
haga tope perfectamente. bearing (12) is perfectly in contact.
No golpee sobre las bolas y/o sobre el anillo interior. Do not strike against the balls and/or the inner ring.
7 - 45
&,&/,67,&$
7.2.3 CONTROLLO
Controllare l'integrit di tutti i componenti e in
particolar modo quelli che sono indicati di se-
guito.
CUSCINETTI
X Girare manualmente l'anello interno (1) che deve ruo-
tare dolcemente, senza impedimenti e/o rumorosit.
Non si devono riscontrare giochi assiali.
I cuscinetti che presentano questi inconvenienti devo-
no essere sostituiti.
Applicare del grasso sulle sfere (o sui rulli) ai
lati di ogni cuscinetto, vedi 1.7 (TABELLA LU-
BRIFICANTI).
PERNO RUOTA
X Utilizzando un comparatore, controllare l'eccentricit
del perno. Se l'eccentricit supera il valore limite, so-
stituire il perno.
Eccentricit massima: 0,25 mm
Applicare del grasso sul perno (solo nella
zona di contatto con i cuscinetti), vedi 1.7 (TA-
BELLA LUBRIFICANTI).
CERCHIO
X Utilizzando un comparatore, controllare che l'eccentri-
cit radiale ed assiale del cerchio non superi il valore
limite.
Una eccessiva eccentricit di solito causata dai cu-
scinetti usurati o danneggiati.
Se dopo la sostituzione dei cuscinetti il valore non rien-
tra nel limite indicato, sostituire il cerchio.
Eccentricit radiale ed assiale massima: 2 mm
RINVIO TACHIMETRO
X Controllare che non vi siano segni evidenti di danneg-
giamento e/o eccessiva usura.
PNEUMATICO
X Controllare lo stato del pneumatico, vedi 2.23 (PNEU-
MATICI) e 7.4 (PNEUMATICI).
7 - 46
3$57(&,&/2 &+$66,63$576
Controle la integridad de todos los compo-
nentes y, especialmente, de los indicados a Make sure that all the components are sound,
continuacin. particularly the following:
COJINETES BEARINGS
X Gire con la mano el anillo interior (1) el cual tiene que X Manually rotate the inner ring (1). It should rotate
girar suavemente, sin bloquearse ni hacer ruido. smoothly, without jamming and/or noise.
No deben notarse desajustes. There should be no axial clearance.
Hay que sustituir los cojinetes que muestren tales in- The bearings showing the defects mentioned above
convenientes. should be changed.
Engrase las bolas (o los rodillos), en los lados Apply grease on the balls (or rollers) on both
de cada cojinete, vase 1.7 (TABLA DE LOS sides of the bearings, see 1.7 (LUBRICANT
LUBRICANTES). CHART).
Engrase el eje (slo en la zona de contacto Apply grease on the pin (only in the area of
con los cojinetes), vase 1.7 (TABLA DE LOS contact with the bearings), see 1.7 (LUBRI-
LUBRICANTES). CANT CHART).
LLANTA RIM
X Utilizando un comparador, controle que la excentrici- X Using a comparator, make sure that the radial and axi-
dad radial y axial de la llanta no supere el valor lmite. al eccentricity of the rim do not exceed the limit value.
Normalmente, una excentricidad excesiva se debe a Excessive eccentricity is usually caused by worn or
cojinetes desgastados o daados. damaged bearings.
Si tras haber sustituido los cojinetes el valor no retorna If, after changing the bearings, the value does not re-
dentro de los lmites indicados, sustituya la llanta. turn within the indicated limit, change the rim.
Excentricidad radial y axial mxima: 2 mm Maximum radial and axial eccentricity: 2 mm.
Engrasa el interior de la transmisin del velo-
cmetro, vase 1.7 (TABLA DE LOS LUBRI-
CANTES).
Apply grease inside the speedometer control,
see 1.7 (LUBRICANT CHART).
NEUMATICO TYRE
X Controle las condiciones del neumtico, vase 2.23 X Check the conditions of the tyre, see 2.23 (TYRES)
(NEUMTICOS) y 7.4 (NEUMATICOS). and 7.4 (TYRES).
7 - 47
&,&/,67,&$
7.2.4 RIMONTAGGIO
Leggere attentamente 1.4 (PRECAUZIONI E INFOR-
MAZIONI GENERALI).
Nel rimontaggio porre attenzione a non dan-
neggiare la tubazione, il disco e le pastiglie del
freno.
Ingrassare linterno del rinvio tachimetro/con-
tachilometri, vedi 1.7 (TABELLA LUBRIFICAN-
TI).
Causa il peso e l'ingombro del veicolo, l'ope-
razione che segue richiede l'intervento di un
secondo operatore.
Procedere con cautela e assicurarsi di poter sostene-
re il peso del veicolo.
Dopo il rimontaggio, azionare ripetutamente la
leva del freno anteriore e controllare il corret-
to funzionamento del sistema frenante.
7 - 48
3$57(&,&/2 &+$66,63$576
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
Durante la instalacin ponga cuidado en no While reassembling the wheel, be careful not
daar los tubos, el disco y las pastillas del fre- to damage the brake pipe, the disc and the
no. pads.
X Coloque la rueda entre las barras de la horquilla. X Position the wheel between the fork tubes.
Engrase el interior del cable reenvo velocme-
tro/cuentakilmetros, vase 1.7 (TABLA DE Grease the inside of the speedometer/odome-
LOS LUBRICANTES). ter control, see 1.7 (LUBRICANT CHART).
X Coloque la lengeta del reenvo velocmetro/cuentaki- X Position the speedometer/odometer control tang (1) in
lmetros (1) en el alojamiento correspondiente del the relevant seat in the wheel hub.
cubo rueda. X Correctly position the traction ring (2), the sealing ring
X Coloque correctamente el anillo de arrastre (2), el re- (3) and the odometer control seat in correspondence
tn (3) y el alojamiento del reenvo cuentakilmetros with the apposite antirotation pin (4).
en correspondencia de la espiga antirrotacin (4). X Shift the mudguard support as much as necessary to
X Desplace el soporte guardabarros lo suficiente para in- insert the wheel pin partially (from the right side of the
troducir parcialmente el eje de la rueda (desde lado vehicle).
derecho del vehculo). X Insert the spacer (7) between the wheel hub and the
X Introduzca el distanciador (7) entre el cubo de la rueda fork left tube.
y la barra izquierda de la horquilla.
Due to the weight and dimensions of the vehi-
A causa del peso y del espacio que ocupa el cle, the following operation cannot be per-
vehculo la operacin que sigue a continua- formed by one person only.
cin necesita la intervencin de un segundo Proceed with care and make sure that you can sup-
operador. Siga adelante con cuidado y compruebe si port the weight of the vehicle.
puede soportar el peso del vehculo.
Raise the front part of the vehicle and remove the sup-
X Levante la parte delantera del vehculo y desplace el port positioned under the engine during the disassem-
soporte colocado por debajo del motor durante el des- bly.
montaje.
X Lower the vehicle and position it on the stand.
X Baje el vehculo y colquelo sobre el caballete.
X Correctly position the oil pan guard, see 7.1.9 (RE-
X Coloque correctamente el protector de crter, vase MOVING THE OIL PAN GUARD).
7.1.9 (DESMONTAJE PROTECTOR DE CARTER).
X With pulled front brake lever, press the handlebars re-
X Con la palanca del freno delantera accionada, presio- peatedly, thrusting the fork downwards. In this way the
ne varias veces sobre el manillar empujando hacia el fork tubes will settle properly.
fondo la horquilla. De tal forma las barras de la horqui-
lla se ajustarn de manera apropiada. X Screw and tighten the two screws (8).
X Atornille y apriete los dos tornillos (8). X Tighten the wheel pin clamp screws (9).
X Apriete el tornillo (9) de la brida del eje de la rueda. Wheel pin clamp screw driving torque:
12 Nm (1,2 kgm).
Par de apriete tornillos brida eje rueda:
12 Nm (1,2 kgm). After reassembly, pull the front brake lever re-
Tras haber instalado la rueda, accione varias peatedly and check the correct functioning of
veces la palanca del freno delantero y contro- the braking system.
le el funcionamiento correcto del sistema de
frenado. Check the centering and balancing of the wheel.
Controle el centrado y el equilibrado de la rueda.
7 - 49
&,&/,67,&$ 3$57(&,&/2 &+$66,63$576
7 - 50
&,&/,67,&$ 3$57(&,&/2 &+$66,63$576
Q = GRASSO, vedi 1.7 (TABEL- Q = GRASA vase 1.7 (TABLA Q = GREASE, see 1.7 (LUBRI-
LA LUBRIFICANTI). DE LOS LUBRICANTES). CANT CHART).
7 - 51
&,&/,67,&$
7.3.1 RIMOZIONE
Causa il peso e l'ingombro del veicolo, l'ope-
razione che segue richiede l'intervento di un
secondo operatore.
Procedere con cautela e assicurarsi di poter sostene-
re il peso del veicolo.
Pericolo di caduta del veicolo.
Provvedere al bilanciamento del veicolo per
impedirne la caduta.
Non azionare la leva del freno posteriore dopo
aver rimosso la ruota, altrimenti il pistoncino
della pinza potrebbe fuoriuscire dalla sede,
causando la perdita del liquido freni.
7 - 52
3$57(&,&/2 &+$66,63$576
Lea con mucho cuidado 1.4 (PRECAUCIONES E IN- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
FORMACIONES GENERALES) y 2.29 (RUEDA TRA- TION) and 2.29 (REAR WHEEL) carefully.
SERA).
X Position the vehicle on the centre stand - or on an
X Coloque el vehculo sobre el caballete central - o apposite support stand fixed to the centre stand cou-
sobre un especial caballete de sostn fijado en los pi- plings.
votes del caballete central. X Remove the oil pan guard, see 7.1.9 (REMOVING
X Desmonte el protector de crter, vase 7.1.9 (DES- THE OIL PAN GUARD).
MONTAJE PROTECTOR DE CARTER).
Due to the weight and dimensions of the vehi-
A causa del peso y del espacio que ocupa el cle, the following operation cannot be per-
vehculo, la operacin que sigue a continua- formed by one person only.
cin necesita la intervencin de un segundo Proceed with care and make sure that you can sup-
operador. port the weight of the vehicle.
Siga adelante con cuidado y compruebe si puede so-
portar el peso del vehculo. Weight of the vehicle without driver (ready for
starting): 200 kg.
Peso en vaco del vehculo (en orden de mar-
cha): 200 kg. X Raise the rear part of the vehicle, have a suitable sup-
port (the height of which should be 350 mm) placed
X Levante la parte trasera del vehculo y coloque un so- under the engine, so that the rear wheel can rotate
porte adecuado (con altura 350 mm) por debajo del freely and the vehicle cannot fall down.
motor de manera que la rueda trasera tenga espacio
suficiente para moverse libremente y para evitar la The vehicle may fall down.
cada del vehculo. Provide for balancing the vehicle, in order to
prevent it from falling down.
Peligro cada del vehculo.
Provea a equilibrar el vehculo para que no X Lock the wheel pin (1) rotation, by means of the suita-
caiga. ble spanner.
X Unscrew and remove the nut (2) and take the washer
X Bloquee con la llave correspondiente la rotacin del (3).
eje de la rueda (1).
X Destornille y quite la tuerca (2) y guarde la arandela To facilitate the extraction of the wheel pin,
(3). slightly raise the wheel.
X Extraiga desde la parte trasera la rueda del basculan- Never pull the rear brake lever after removing
te, poniendo cuidado al extraer el disco de la pinza del the wheel, otherwise the caliper piston may
freno. go out of its seat, thus causing the outflow of
the brake fluid.
No accione la palanca del freno trasero tras
haber extrado la rueda, en caso contrario el
mbolo de la pinza del freno podra salirse de
su alojamiento, causando la prdida del lquido de
los frenos.
7 - 53
&,&/,67,&$
X
Dopo ogni smontaggio i cuscinetti devono es-
sere controllati ed eventualmente sostituiti.
Sfilare il distanziale laterale destro (7).
X Con uno straccio pulire i due lati del mozzo.
X +Sfilare la guarnizione di tenuta (8).
X +Rimuovere l'anello seeger (9).
X Togliere la corona completa di mozzo (10) e parastrap-
pi (11).
Nel rimontaggio utilizzare per l'inserimento
dei cuscinetti un tampone con diametro ugua-
le all'anello esterno dei cuscinetti.
Non battere sulle sfere e/o sull'anello interno.
7.3.3 CONTROLLO
CUSCINETTI
Vedi 7.2.3 (CONTROLLO; CUSCINETTI).
PERNO RUOTA
Vedi 7.2.3 (CONTROLLO; PERNO RUOTA).
CERCHIO
Vedi 7.2.3 (CONTROLLO; CERCHIO).
PARASTRAPPI
X Controllare che i tasselli sul parastrappi (1) non siano
danneggiati e/o eccessivamente usurati.
Se necessario sostituire il parastrappi.
Se si riscontra un gioco eccessivo il parastrappi deve
essere sostituito.
X Ruotare manualmente la corona (2) e verificare il gioco
tra corona e mozzo ruota (3).
CORONA
X Controllare lo stato dei denti della corona (2) e del pi-
gnone. Se si riscontra una eccessiva usura sostituire
corona, pignone e catena di trasmissione, vedi 7.1.23
(RIMOZIONE CATENA DI TRASMISSIONE).
PNEUMATICO
X Controllare lo stato del pneumatico, vedi 2.23 (PNEU-
MATICI).
7 - 54
3$57(&,&/2 &+$66,63$576
The bearings must be checked and if neces-
Despus de cada desmontaje controle los co- sary changed every time they are disassem-
jinetes y, si es necesario, sustityalos. bled.
X Extraiga el distanciador lateral derecho (7). X Remove the right side spacer (7).
X Con un trapo limpie los dos lados del cubo. X Clean both sides of hub with a cloth.
X +Quite la junta estanca (8). X +Remove the seal (8).
X +Quite la arandela Seeger (9). X +Remove the snap ring (9).
X Quite la corona con el cubo (10) y la junta amortigua- X Remove the crown gear complete with hub (10) and
dora (11). flexible coupling (11).
X Limpie muy bien el interior del cubo. Upon reassembly, to insert the bearings use a
punch with diameter equal to the outer ring of
Para montar nuevamente los cojinetes, utilice
the bearings.
una herramienta con dimetro igual al anillo
Do not strike against the balls and/or the inner ring.
exterior de los cojinetes.
No golpee sobre las bolas y/o sobre el anillo interior.
Controle la integridad de todos los compo-
nentes y, especialmente, de los indicados a Make sure that all the components are sound,
continuacin. particularly the following:
COJINETES BEARINGS
Vase 7.2.3 (CONTROL; COJINETES). See 7.2.3 (CHECKING; BEARINGS).
LLANTA RIM
Vase 7.2.3 (CONTROL; LLANTA). See 7.2.3 (CHECKING; RIM)
Para evitar que los componentes nuevos se
desgasten prematuramente, sustityalos en
conjunto.
To avoid premature wear of the new compo-
nents, change them all.
TYRE
NEUMATICO X Check the conditions of the tyre, see 2.23 (TYRES).
X Controle el estado del neumtico, vase 2.23 (NEU-
MTICOS).
7 - 55
&,&/,67,&$
7.3.4 RIMONTAGGIO
Leggere attentamente 1.4 (PRECAUZIONI E INFOR-
MAZIONI GENERALI).
Pericolo di lesioni.
Non inserire le dita per allineare le sedi.
Causa il peso e l'ingombro del veicolo, l'ope-
razione che segue richiede l'intervento di un
secondo operatore.
Procedere con cautela e assicurarsi di poter sostene-
re il peso del veicolo.
Dopo il rimontaggio, azionare ripetutamente
la leva del freno posteriore e controllare il cor-
retto funzionamento del sistema frenante.
7 - 56
3$57(&,&/2 &+$66,63$576
X Coloque la rueda trasera entre las barras del bascu- X Position the rear wheel between the tubes of the rear
lante. fork.
X Haga avanzar la rueda y coloque la cadena de trans- X Make the wheel advance and position the gearing
misin (1) sobre la corona dentada (2). chain (1) on the crown gear (2).
Peligro de lesiones.
No introduzca los dedos para alinear los aloja- Risk of injuries.
mientos. Do not use your fingers to align the seats.
X Ponga hacia atrs la rueda alineando el alojamiento X Make the wheel move backwards and align the pin
del eje sobre el cubo de la rueda con los alojamientos seat on the wheel hub with the pin seats on the tubes
del eje sobre los brazos del basculante. of the rear fork.
DE LOS LUBRICANTES). CHART).
Para favorecer la introduccin del eje de la To facilitate the insertion of the wheel pin,
rueda, levante moderadamente la rueda. slightly raise the wheel.
X Introduzca, desde el lado izquierdo del vehculo, el eje X Insert the wheel pin (3) complete with washer (4) from
de la rueda (3) junto con su correspondiente arandela the left side of the vehicle.
(4).
Make sure that the wheel pin has been insert-
Controle si se ha introducido del todo el eje de
ed completely.
la rueda.
X Introduzca la arandela (5) y enrosque del todo la tuer- X Fit the washer (5) and screw the nut (6) completely.
ca (6). X Check the chain tension, see 2.16.1 (CLEARANCE
X Controle la tensin de la cadena, vase 2.16.1 (CON- CONTROL).
TROL DEL JUEGO). X Lock the wheel pin (3) rotation by means of the suita-
X Bloquee, con la llave correspondiente, la rotacin del ble spanner and tighten the nut (6).
eje de la rueda (3) y apriete la tuerca (6). Wheel pin-nut (6-3) driving torque:
Par de apriete tuerca-eje rueda (6-3): 100 Nm (10 kgm).
100 Nm (10 kgm).
Due to the weight and dimensions of the vehi-
A causa del peso y del espacio que ocupa el
cle, the following operation cannot be per-
vehculo, la operacin que sigue a continua-
formed by one person only.
cin necesita la intervencin de un segundo
Proceed with care and make sure that you can sup-
operador.
port the weight of the vehicle.
Siga adelante con cuidado y compruebe si puede so-
portar el peso del vehculo.
Weight of the vehicle without driver (ready for
Peso en vaco del vehculo (en orden de mar- starting): 200 kg.
cha): 200 kg.
X Raise the rear part of the vehicle and remove the sup-
X Levante la parte trasera del vehculo y desplace el so-
port positioned under the engine during the disassem-
porte que se haba colocado por debajo del motor du-
bly.
rante el desmontaje.
X Lower the vehicle and position it on the stand.
X Baje el vehculo y colquelo sobre el caballete.
X Correctly position the oil pan guard, see 7.1.9 (RE-
X Monte correctamente el protector de crter, vase
MOVING THE OIL PAN GUARD).
7.1.9 (DESMONTAJE PROTECTOR DE CARTER).
Tras haber concluido la instalacin, accione After reassembly, pull the rear brake lever re-
varias veces la palanca del freno trasero y peatedly and check the correct functioning of
controle el funcionamiento correcto del siste- the braking system.
ma de frenado.
Check the centering and balancing of the wheel.
Controle el centrado y el equilibrado de la rueda.
7 - 57
&,&/,67,&$
31(80$7,&,
7.4.1 SMONTAGGIO
Leggere attentamente 1.4 (PRECAUZIONI E INFOR-
MAZIONI GENERALI) e 2.23 (PNEUMATICI).
Per lo smontaggio del pneumatico dal cerchio, si consi-
glia di utilizzare gli attrezzi indicati.
Legenda
1) Supporto ruota
2) Leva di comando
3) Levagomma
4) Albero di centraggio
5) Rullo premi-tallone
6) Rullo guida-cerchio
7) Separa-tallone
8) Protezione cerchio
9) Manometro
10) Lubrificante per pneumatici
7 - 58
3$57(&,&/2 &+$66,63$576
X Desenrosque y quite el capuchn de cierre (11). X Unscrew and remove the closing cap (11).
X Desinfle completamente la cmara de aire. X Deflate the inner tube completely.
X Desenrosque y quite la tuerca de sujecin de la vlvu- X Unscrew and remove the valve lock ring (12).
la (12).
Mark the tyre with chalk, to show its position
Marque el neumtico con tiza para evidenciar with respect to the rim and to the rotation di-
la posicin del mismo con respecto a la llanta rection.
y al sentido de rotacin.
7 - 59
&,&/,67,&$
7 - 60
3$57(&,&/2 &+$66,63$576
X Introduzca el eje de centrado (1) en el cubo de la rue- X Fit the trueing shaft (1) in the wheel hub and then lock
da y luego bloquela con el soporte para rueda (2). it with the wheel support (2).
X Fije la palanca de mando (3) en el eje de centrado (1). X Fasten the control lever (3) to the trueing shaft (1).
X Fije el separador del taln (4) en la palanca de mando X Fasten the bead separator (4) to the control lever (3)
(3) y separe el taln del neumtico de la llanta. and separate the bead from the rim.
Gire la rueda y separe el otro taln del neumtico de la Urn the wheel and separate the other bead from the
llanta. rim.
X Instale el rodillo de gua de la llanta (5). X Install the rim guide roller (5).
X Coloque la proteccin de la llanta (6) y quite el taln X Position the rim protector (6) and withdraw the tyre
del neumtico con la ayuda del abrellantas (7). bead with the help of the tyre iron (7).
X Coloque el abrellantas (7) contra la palanca de mando X Place the tyre iron (7) against the control lever (3) and
(3) y hgalo girar alrededor de la llanta. make it rotate around the rim.
X Repita el mismo procedimiento para desmontar el otro X Repeat the above procedure to disassemble the other
taln de la llanta. bead from the rim.
X Extraiga el neumtico. X Remove the tyre.
X Extraiga la cmara de aire. X Remove the inner tube.
7 - 61
&,&/,67,&$
7.4.2 CONTROLLO
CERCHIO
Prima di controllare il cerchio eliminare ogni residuo di
gomma o di ruggine.
Se si presenta anche uno solo dei difetti elencati, sostitui-
re il cerchio con uno nuovo.
X Deformazioni o fessurazioni.
X Rigature o difetti.
PNEUMATICO
Controllare con attenzione il pneumatico dopo averlo
smontato. Se presenta anche uno solo dei difetti elencati,
non riparare il pneumatico ma sostituirlo con uno nuovo.
X Buco o fessura di diametro o lunghezza superiore a
5 mm.
X Rigatura o fessurazione del fianco.
X Profondit del battistrada inferiore a 2 mm.
X Tele scollate.
X Separazione del battistrada.
X Deformazione o usura non uniforme del battistrada.
X Rigature del tallone.
X Cavi interrotti.
X Danneggiamenti dovuti a slittamenti (zone appiattite).
X Anomalie della tenuta interna.
Quando riparate un pneumatico forato, segui-
re le istruzioni per la riparazione e utilizzare
solo i componenti raccomandati per la ripara-
zione.
Nel caso leccentricit assiale e radiale della
ruota superi i 2 mm, provvedere alla regolazio-
ne tensione raggi, fino a ristabilire le normali condi-
zioni di utilizzo.
CAMERA DARIA
Controllare con attenzione la camera daria ricercando
leventuale foro o taglio, procedendo poi alla riparazione.
Se presenta anche uno solo dei difetti elencati, non ripa-
rare la camera daria ma sostituirla con una nuova.
X Buco o fessura di diametro o lunghezza superiore a 5
mm.
X Evidenti screpolature attorno alla base della valvola.
X Bolle o rigonfiamenti anomali durante il gonfiaggio per
la ricerca dei fori.
Quando riparate una camera daria forata, se-
guire le istruzioni per la riparazione e utilizza-
re solo i componenti raccomandati per la ripa-
razione.
X
Non applicare mai, per nessun motivo, gras-
so, olio o benzina sui talloni del pneumatico.
Se si rimonta il pneumatico smontato in precedenza,
assicurarsi che la freccia stampata sullo stesso sia
orientata nel senso di rotazione della ruota e fare coin-
cidere il segno riportato sul pneumatico allo smontag-
gio con il segno sul cerchio.
7 - 62
3$57(&,&/2 &+$66,63$576
LLANTA RIM
Antes de controlar la llanta elimine todos los residuos de Before checking the rim, eliminate all rubber or rust resi-
goma u xido. dues.
Sustituya la llanta con otra nueva si encuentra uno solo If one or more of the listed defects are present, change
de los defectos mencionados a continuacin. the rim.
X Deformaciones o fisuras. X Deformation or cracking.
X Estras o defectos. X Marks/lines or defects.
NEUMATICO TYRE
Controle con atencin el neumtico tras haberlo desmon- Thoroughly check the tyre after removing it. If one or
tado. En caso de que encuentre uno solo de los defectos more of the listed defects are present, do not repair the
mencionados a continuacin, no repare el neumtico, tyre, but change it.
sino que sustityalo con otro nuevo. X Hole or crack exceeding 5 mm in diameter or length.
X Agujero o fisura de dimetro o longitud superior a 5 mm. X Mark or cracking on the side.
X Estras o fisuras del flanco. X Tread depth less than 2 mm.
X Profundidad de la banda de rodamiento inferior a 2 mm. X Ply unglued.
X Telas despegadas. X Separated tread.
X Banda de rodamiento separada. X Deformation or wear of tread not uniform.
X Deformacin o desgaste no uniforme de la banda de X Marks/lines on the bead.
rodamiento. X Damage due to skidding (flattened areas).
X Estras en el taln. X Anomalies in the inner seal.
X Cables interrumpidos.
X Daos provocados por patinajes (zonas aplastadas). When repairing a punctured tyre, follow the in-
X Anomalas de la estabilidad interior. structions and use only the components rec-
ommended for repairing.
Cuando repare un neumtico pinchado, siga
las instrucciones para la reparacin y utilice
In case the axial and radial eccentricity ex-
slo los componentes aconsejados para la
ceed 2 mm, adjust the tension of the spokes
misma.
until the normal conditions are reestablished.
Si la excentricidad axial y radial de la rueda su-
pera los 2 mm, ajuste la tensin de los radios
hasta restablecer las condiciones normales de uso.
When repairing a punctured inner tube, follow
Cuando repare una cmara de aire agujerea-
the instructions and use only the components
da, siga las instrucciones para la reparacin y
recommended for repairing.
utilice slo los componentes aconsejados
para la reparacin.
Nunca y por ningn motivo aplique grasa,
aceite o gasolina en los talones del neumti- Never apply grease, oil or petrol to the beads
co. of the tyre for any reason whatsoever.
X Si se monta nuevamente el neumtico que haba sido X If a disassembled tyre is to be reassembled, make
desmontado, controle que la flecha impresa sobre sure that the arrow stamped on it is pointed in the
ste quede orientada en el sentido de rotacin de la wheel rotation direction and make the chalk mark
rueda y haga coincidir la referencia sobre el neumtico made on the tyre upon disassembly coincide with the
en el momento del desmontaje con la marca sobre la mark on the rim.
llanta.
7 - 63
&,&/,67,&$
X Gonfiare il pneumatico.
Per lutilizzo del veicolo, non gonfiare il pneu-
matico per pi di:
ANTERIORE 180 kPa (1,8 bar)
POSTERIORE 190 220 kPa (1,9 2,2 bar)
Potrebbe esplodere causando gravi ferite.
Non mettersi mai sopra il pneumatico durante il gon-
fiaggio.
Non superare i 50 km/h nelle prime 24 ore che
seguono la riparazione del pneumatico; l'in-
serto o la pezza potrebbero non essere com-
pletamente incollati.
Con un pneumatico riparato non superare la velocit
di 130 km/h.
7 - 64
3$57(&,&/2 &+$66,63$576
X Coloque el rodillo para apretar el taln (1). X Position the bead pressing roller (1).
X Haga girar la palanca de mando (2) alrededor de la llan- X Make the control lever (2) rotate around the rim in or-
ta, para introducir completamente el taln en la llanta. der to insert the bead completely in the rim.
Monte primero el taln inferior, luego el superior. Position the lower bead first, then the upper bead.
X Quite la rueda del soporte. X Remove the wheel from the support.
X Haga rebotar varias veces el neumtico mientras lo X Make the tyre bounce several times and at the same
hace rodar. time rotate it.
Esta operacin empuja los talones hacia los aloja- This operation pushes the beads towards the seats on
mientos en la llanta, facilitando el inflado. the rim, thus facilitating the inflation of the tyre.
Para utilizar el vehculo, no infle el neumtico To use the vehicle, do not inflate the tyre more
ms de: than:
DELANTERO 180 kPa (1,8 bar) FRONT TYRE 180 kPa (1.8 bar)
TRASERO 190 220 kPa (1,9 2,2 bar) REAR TYRE 190-220 kPa (2.2 bar)
Podra explotar provocando heridas graves. It may explode, causing serious injuries.
Nunca se ponga sobre el neumtico cuando lo infle. Never sit on the tyre while inflating it.
X Tras haber instalado correctamente el neumtico en la X When the tyre is properly installed on the rim, regulate
llanta, regule la presin segn el valor indicado. the pressure to the prescribed value.
X Si es necesario efecte el equilibrado. X If necessary, balance the wheel.
No supere los 50 km/h durante las primeras 24 Do not exceed 50 km/h in the first 24 hours fol-
horas despus de la reparacin del neumti- lowing the repair of the tyre; the insert or the
co; el parche podra no estar completamente patch might not be completely glued.
pegado. Con un neumtico reparado no supere los Do not exceed the speed of 130 km/h with a repaired
130 km/h de velocidad. tyre.
7 - 65
&,&/,67,&$ 3$57(&,&/2 &+$66,63$576
7 - 66
&,&/,67,&$ 3$57(&,&/2 &+$66,63$576
1) Leva comando freno 1) Palanca de mando del freno 1) Brake control lver
2) Pompa/serbatoio liquido freno 2) Bomba/depsito lquido de freno 2) Brake fluid pump/tank
3) Tubo liquido freno 3) Tubo lquido de freno 3) Brake fluid pipe
4) Valvola di spurgo 4) Vlvula de purga 4) Bleeder
5) Pinza freno 5) Pinza de freno 5) Brake caliper
6) Pastiglie freno 6) Pastillas de freno 6) Brake pads
7) Disco freno 7) Disco de freno 7) Brake disc
8) Vite registro pompa freno 8) Tornillo de regulacin de la bom- 8) Brake pump adjusting screw
ba de freno
X Liquido freni, vedi 1.2.4 (LIQUIDO X Lquido frenos, vase 1.2.4 (L- X Brake fluid, see 1.2.4 (BRAKE
FRENI). QUIDO DE FRENOS). FLUID).
X Controllo e rabbocco liquido freni, X Control y relleno lquido frenos, X Brake fluid checking and topping
vedi 2.17 (CONTROLLO E RAB- vase 2.17 (CONTROL Y RELLE- up, see 2.17 (CHECKING AND
BOCCO LIQUIDO FRENO ANTE- NO LIQUIDO FRENO DELANTE- TOPPING UP THE FRONT
RIORE). RO). BRAKE FLUID).
X Spurgo aria impianto frenante, X Purga aire sistema de frenado, X Braking system bleeding, see 2.19
vedi 2.19 (SPURGO ARIA IM- vase 2.19 (PURGA DEL AIRE (BLEEDING THE BRAKING SYS-
PIANTO FRENANTE). DEL SISTEMA DE FRENADO). TEM).
X Regolaizone leva freno, vedi 2.21 X Ajuste palanca freno, vase 2.21 X Brake lever adjustment, see 2.21
(REGOLAZIONE LEVA FRENO (AJUSTE DE LA PALANCA DEL (FRONT BRAKE LEVER AD-
ANTERIORE). FRENO DELANTERO). JUSTMENT).
X Verifica usura pastiglie, vedi 2.22 X Control desgaste pastillas, vase X Brake pad wear, see 2.22
(VERIFICA USURA PASTIGLIE). 2.22 (COMPROBACION DES- (CHECKING THE BRAKE PAD
X Componenti impianto frenante, GASTE PASTILLAS). WEAR).
vedi 8.5.5 (IMPIANTO FRENAN- X Componentes sistema de frenado, X Braking system components, see
TE). vase 8.5.5 (INSTALACIN DE 8.5.5 (BRAKING SYSTEM.).
FRENADO).
7 - 67
&,&/,67,&$
Dopo avere tolto le pastiglie, non azionare la
leva comando freno, altrimenti i pistoncini
della pinza potrebbero fuoriuscire dalla sede
con conseguente perdita del liquido freni.
Sostituire sempre entrambe le pastiglie e ac-
certarsi del loro corretto posizionamento
all'interno della pinza.
7.5.2 CONTROLLO DISCO FRENO
Operazioni da effettuare con disco freno in-
stallato sulla ruota.
X Controllare l'usura del disco misurando con un micro-
metro lo spessore minimo in diversi punti.
Se lo spessore minimo, anche in un solo punto del di-
sco, inferiore al valore minimo, sostituire il disco.
Valore minimo dello spessore del disco: 4,5 mm
X Utilizzando un comparatore, controllare che loscilla-
zione massima del disco non superi la tolleranza, altri-
menti sostituirlo.
Tolleranza di oscillazione del disco: 0,3 mm
Coppia di serraggio viti fissaggio disco:
12 Nm (1,2 kgm).
Montare con LOCTITE frena filetti medio.
Nel rimontaggio applicare LOCTITE frena fi-
letti medio sulla filettatura delle viti disco fre-
no.
7 - 68
3$57(&,&/2 &+$66,63$576
Lea con mucho cuidado 1.4 (PRECAUCIONES E IN- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
FORMACIONES GENERALES). TION) carefully.
After removing the pads, do not pull the brake
Tras haber quitado la pastillas no accione la control lever, otherwise the caliper pins may
palanca de mando del freno, en caso contrario go out of their seats and cause the outflow of
los pistones de la pinza podran salirse del the brake fluid.
alojamiento y provocar la prdida del lquido de fre-
nos. X Insert two new pads.
X Introduzca dos pastillas nuevas. Always change both pads and make sure that
they are correctly positioned inside the cali-
Sustituya siempre ambas pastillas y controle per.
que estn bien colocadas en el interior de la
pinza. X Insert the pin (2).
X Insert the flexible stop pin (1).
X Introduzca el perno (2). X Check the brake fluid level, see 2.17 (CHECKING
X introduzca el pasador elstico de cierre (1). AND TOPPING UP THE FRONT BRAKE FLUID).
X Controle el nivel lquido frenos, vase 2.17 (CON-
TROL Y RELLENO LIQUIDO FRENO DELANTERO).
7.5.2 CONTROL DISCO FRENO 7.5.2 CHECKING THE BRAKE DISC
Hay que realizar las siguientes operaciones These operations must be performed with the
con el disco freno instalado en la rueda. brake disc installed on the wheel.
X Controle el desgaste del disco midiendo con un micr- X Check the wear on the disc by measuring the minimum
metro, en varios puntos, el espesor mnimo. thickness in several places by means of a micrometer.
Si el espesor mnimo fuera inferior al valor mnimo, If, even in one point of the disc only, the minimum thick-
aunque en un solo punto, sustituya el disco. ness is below the minimum value, change the disc.
Valor mnimo del espesor del disco: 4,5 mm Brake disc min. thickness: 4.5 mm.
X Utilizando un comparador, controle que la oscilacin X Using a comparator, make sure that the maximum
mxima del disco no supere la tolerancia, en caso wobbling of the disc does not exceed the limit value,
contrario sustityalo. otherwise change it.
Tolerancia de oscilacin del disco: 0,3 mm Brake disc max. wobbling: 0.3 mm
Par de apriete tornillos de sujecin disco: Disc fastening screw driving torque:
12 Nm (1,2 kgm) 12 Nm (1.2 kgm).
Cuando lo instale aplique LOCTITE frena roscas Assemble with medium LOCTITE thread restrainer.
medio.
Upon reassembly, apply medium LOCTITE
Durante el reensamblaje aplique LOCTITE thread restrainer on the thread of the brake
frena roscas medio sobre la rosca de los tor- disc screws.
nillos disco freno.
Upon reassembly, screw all the screws manu-
Durante el reensamblaje atornille todos los ally and tighten them proceeding diagonally in
tornillos manualmente y apritelos actuando the following order: A-B-C-D-E-F.
en diagonal segn el siguiente orden: A-B-C-D-E-F
X Remove the brake disc (5).
X Extraiga el disco freno (5).
7 - 69
&,&/,67,&$ 3$57(&,&/2 &+$66,63$576
7 - 70
&,&/,67,&$ 3$57(&,&/2 &+$66,63$576
X Liquido freni, vedi 1.2.4 (LIQUIDO X Lquido frenos, vase 1.2.4 (L- X Brake fluid, see 1.2.4 (BRAKE
FRENI). QUIDO DE FRENOS). FLUID).
X Controllo e rabbocco liquido freni, X Control y relleno lquido frenos, X Brake fluid checking and topping
vedi 2.18 (CONTROLLO E RAB- vase 2.18 (CONTROL Y RELLE- up, see 2.18 (CHECKING AND
BOCCO LIQUIDO FRENO PO- NO LIQUIDO FRENO TRASE- TOPPING UP THE REAR BRAKE
STERIORE). RO). FLUID).
X Spurgo aria impianto frenante, X Purga aire sistema de frenado, X Braking system bleeding, see 2.19
vedi 2.19 (SPURGO ARIA IM- vase 2.19 (PURGA DEL AIRE (BLEEDING THE BRAKING SYS-
PIANTO FRENANTE)). DEL SISTEMA DE FRENADO). TEM).
X Regolaizone pedale freno, vedi X Ajuste palanca freno, vase 2.20 X Brake pedal adjustment, see 2.20
2.20 (REGOLAZIONE PEDALE (AJUSTE DEL PEDAL DEL FRE- (REAR BRAKE PEDAL ADJUST-
FRENO POSTERIORE). NO TRASERO). MENT).
X Verifica usura pastiglie, vedi 2.22 X Control desgaste pastillas, vase X Brake pad wear, see 2.22
(VERIFICA USURA PASTIGLIE). 2.22 (COMPROBACION DES- (CHECKING THE BRAKE PAD
X Componenti impianto frenante, GASTE PASTILLAS). WEAR).
vedi 8.5.5 (IMPIANTO FRENAN- X Componentes sistema de frenado, X Braking system components, see
TE). vase 8.5.5 (INSTALACIN DE 8.5.5 (BRAKING SYSTEM.).
FRENADO).
7 - 71
&,&/,67,&$
Dopo avere tolto le pastiglie non azionare il
pedale comando freno, altrimenti il pistoncino
della pinza potrebbe fuoriuscire dalla sede
con conseguente perdita del liquido freni.
Sostituire sempre entrambe le pastiglie e ac-
certarsi del loro corretto posizionamento
all'interno della pinza.
X
Coppia di serraggio viti (1): 25 Nm (2,5 kgm)
Nel rimontaggio applicare LOCTITE frena fi-
letti medio sulla filettatura delle viti disco fre-
no.
7 - 72
3$57(&,&/2 &+$66,63$576
Lea con mucho cuidado 1.4 (PRECAUCIONES E IN- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
FORMACIONES GENERALES). TION) carefully.
wards.
El tubo del lquido de frenos puede dejarse
conectado. It is not necessary to disconnect the brake flu-
id pipe.
X Apriete, como indicado en la figura, desplazando uni-
formemente el flotador (4) hacia el pistn. X Press, as indicated in the figure, moving the float (4)
X Extraiga las dos pastillas (primero la interior). uniformly towards the caliper pin.
X Extract the two pads (the inner one first).
Tras haber quitado las pastillas no accione la
palanca de mando del freno, en caso contrario After removing the pads, do not pull the brake
los pistones de la pinza podran salirse del control lever, otherwise the caliper pin may go
alojamiento y provocar la prdida del lquido de fre- out of its seat and cause the outflow of the
nos. brake fluid.
Sustituya siempre ambas pastillas y controle Always change both pads and make sure that
que estn bien colocadas en el interior de la they are correctly positioned inside the cali-
pinza. per.
X Introduzca la pinza (2) en el disco y colquela en la X Insert the caliper (2) on the disc and position it on the
placa de soporte (3). support plate (3).
X Atornille los dos tornillos de sujecin (1). X Tighten the two fastening screws (1).
X
Par de apriete tornillos (1): 25 Nm (2,5 kgm)
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
X Extraiga la rueda trasera, vase 7.3.1 (DESMONTA- X Remove the rear wheel, see 7.3.1 (DISASSEMBLY).
JE). X Unscrew and remove the six brake disc screws (5).
X Destornille y quite los seis tornillos disco freno (5). Brake disc screw driving torque:
Par de apriete tornillos disco freno: 12 Nm (1.2 kgm).
12 Nm (1,2 kgm).
Upon reassembly, apply medium LOCTITE
Durante el reensamblaje aplique LOCTITE thread restrainer on the thread of the brake
frena roscas medio sobre la rosca de los tor- disc screws.
nillos disco freno.
Upon reassembly, screw all the screws manu-
Durante el reensamblaje atornille todos los ally and tighten them proceeding diagonally in
tornillos manualmente y apritelos actuando the following order: A-B-C-D-E-F.
en diagonal segn el siguiente orden: A-B-C-D-E-F
X Remove the brake disc (6).
X Extraiga el disco freno (6).
7 - 73
&,&/,67,&$
67(5=2
7.7.1 SMONTAGGIO
Sistemare un supporto adeguato sotto il vei-
colo in modo da impedirne la caduta.
Assicurarsi della stabilit del veicolo.
Utilizzare un supporto adeguato per sostenere
il manubrio che rimane collegato al veicolo
tramite i cavi e il tubo freno.
Operare con cautela.
Non forzare i cavi elettrici o il tubo freno.
Nel rimontaggio la piastra superiore (10) si
deve infilare sul fodero forcella sino a fare
coincidere il bordo superiore di entrambi.
7 - 74
3$57(&,&/2 &+$66,63$576
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
X Desmonte el protector de crter, vase 7.1.9 (DES- X Remove the oil pan guard, see 7.1.9 (REMOVING
MONTAJE PROTECTOR DE CARTER). THE OIL PAN GUARD).
X Coloque el vehculo sobre el caballete central - o X Position the vehicle on the centre stand - or on an
sobre un especial caballete de sostn fijado en los pi- apposite support stand fixed to the centre stand cou-
votes del caballete central y sobre una plataforma ele- plings, on a lifting platform, with the front wheel pro-
vadora con la rueda delantera saliente del borde de la truding from the platform edge.
plataforma.
Put a proper support under the vehicle, in or-
Provea a equilibrar el vehculo para que no der to prevent it from falling down.
caiga. Make sure that the vehicle is stable.
Compruebe la estabilidad del vehculo.
X Raise the lifting platform of about 250 mm.
X Levante la plataforma elevadora de unos 250 mm. X Unscrew and remove the screw (1), releasing the
X Destornille y quite el tornillo (1) soltando la abrazadera clamp (2).
(2). X Unscrew and remove the screw (3) and take the wash-
X Destornille y quite el tornillo (3) y guarde la arandela, er, releasing the collar (4).
soltando el collar (4). X Unscrew and remove the two screws (5) that fasten
X Destornille y quite los dos tornillos (5) de sujecin pin- the front brake caliper (6) and take the relative wash-
za freno delantero (6) y guarde las correspondientes ers.
arandelas. Screw (5) driving torque: 50 Nm (5 kgm).
Par de apriete tornillos (5): 50 Nm (5 kgm). X Withdraw the brake caliper (6) from the disc.
X Extraiga la pinza freno (6) del disco.
To perform the following operations it is not
Para la ejecucin de las siguientes operacio- necessary to remove the front fairing, but it is
nes no es necesario quitar el carenado delan- advisable to do it in order to be able to move more
tero, sino que su desmontaje permite tener mayor li- comfortably, see 7.1.14 (REMOVING THE FRONT
bertad de movimiento, vase 7.1.14 (DESMONTAJE FAIRING).
CARENADO DELANTERO).
X Working on the lower part of the front fairing, discon-
X Actuando por la parte inferior del carenado delantero nect the speedometer/odometer control from the dash-
desconecte el reenvo velocmetro/cuentakilmetros board and withdraw it from the collar.
del salpicadero y extrigalo del collar. X + Unscrew the screw (7):
X + Destornille el tornillo (7). Screw (7) driving torque: 50 Nm (5 kgm).
Par de apriete tornillo (7): 50 Nm (5 kgm). X Loosen and remove the upper nut (8).
X Afloje y quite la tuerca superior (8). Nut (8) driving torque: 100 Nm (10 kgm).
Par de apriete de la tuerca (8): 100 Nm (10 kgm).
Use a proper support for the handlebars,
Utilice un soporte adecuado para sostener el which remain connected to the vehicle
manillar que queda conectado al vehculo por through the electric cables and the brake pipe.
medio de los cables y del tubo freno. Proceed with care.
Maneje con mucho cuidado. Do not force the electric cables or the brake pipe.
No fuerce los cables elctricos o bien el tubo del fre-
no. X Lift the handlebars (9) together with the upper plate
(10), withdrawing the latter from the fork.
X Levante el manillar (9) junto con la placa superior (10), X Bend the handlebars (9), complete with upper plate
extrayndola de la horquilla. (10), forwards and fix it temporarily.
X Plegue el manillar (9) junto con la placa superior (10)
hacia adelante y sujtelo provisionalmente. When reassembling the upper plate (10), in-
sert it in the fork slider until the upper edges
Durante el reensamblaje la placa superior (10) coincide.
tiene que insertarse en la botella de la horqui-
lla hasta hacer coincidir el borde superior de
ambas.
7 - 75
&,&/,67,&$
Causa il peso e lingombro dellavantreno, le
operazioni che seguono richiedono linterven-
to di un secondo operatore. Accertarsi pre-
ventivamente sulle procedure di esecuzione.
Loperazione di rimozione deve essere svolta con la
massima attenzione.
X
Sostenere la forcella per evitare la caduta ac-
cidentale.
Mentre un operatore mantiene in posizione lavantre-
no, allentare e togliere la ghiera (11).
7.7.3 RIMONTAGGIO
7.7.4 REGOLAZIONE
Vedi 2.24 (STERZO).
7 - 76
3$57(&,&/2 &+$66,63$576
A causa del peso y del espacio que ocupa el Due to the weight and dimensions of the fore-
tren delantero, la operacin que sigue a conti- carriage, the following operations cannot be
nuacin necesita la intervencin de un segun- performed by one person only. Verify the pro-
do operador. Compruebe en va preventiva los proce- cedures in advance.
dimientos de ejecucin. The removal must be carried out with the greatest
La operacin de extraccin tiene que ser ejecutada care.
con muchsimo cuidado.
X Mientras que un operador mantiene en posicin el tren X While one operator keeps the forecarriage in the right
delantero, afloje y quite la tuerca de regulacin (11). position, loosen and remove the metal ring (11).
Extraiga el tren delantero (12) del manguito de direccin Withdraw the forecarriage (12) from the steering tube and
y guarde segn el siguiente orden: take the following parts, in the given order:
guardapolvo (13); Antidust gasket (13);
retenes (14); Seals (14);
cojinetes (15). Bearings (15).
X Controle que la alineacin entre la placa superior (10) X Make sure that the upper plate (10) and the lower plate
e inferior sea perfecta. are perfectly aligned.
X Antes de apretar definitivamente la tuerca de regula- X Before tightening the adjusting metal ring (11) and the
cin (11) y el tornillo superior (8) gire el manillar varias upper nut (8) definitively, turn the handlebars more
veces en ambos sentidos para ajustar los cojinetes. than once in both directions, in order to ensure the set-
X Girando el manillar controle que los cables no queden tling of the bearings.
tensos y que no estn retorcidos y/o superpuestos in- X When turning the handlebars, make sure that cables
correctamente. and pipes are not taut and that they are neither twist-
ed, nor overlapping in an incorrect way.
7 - 77
&,&/,67,&$
)25&(//$$17(5,25(
Il tubo di precarica (5) e la molla (6) sono im-
mersi nellolio.
Evitare gocciolamenti nellestrazione.
7 - 78
3$57(&,&/2 &+$66,63$576
Lea con cuidado 1.2.3 (ACEITE PARA HORQUILLA) y Read 1.2.3 (FORK OIL) and 2.25 (FRONT FORK)care-
2.25 (HORQUILLA DELANTERA). fully.
En caso de que note que la horquilla se hunde excesiva- If the fork is found to reach the end of its stroke, it is nec-
mente, es necesario controlar el nivel de aceite en las ba- essary to check the oil level of the fork tubes.
rras. X + Unscrew and remove the plug (1) and take the O-
X + Desenrosque y quite el tapn (1) y guarde la junta
ring (2).
trica (2).
Plug (1) driving torque: 20 Nm (2 kgm).
Par de apriete tapn (1): 20 Nm (2 kgm)
X +Withdraw the half-ring (3).
X +Extraiga el semianillo (3).
X +Withdraw the spring ring (4).
X +Extraiga el anillo portaresorte (4).
The preload tube (5) and the spring (6) guide
El tapn de precarga (5) y el resorte (6) estn tube are immersed in oil.
sumergidos en aceite. Avoid dripping oil during the extraction.
Evite gotear cuando los extraiga.
X +Withdraw the preload tube (5).
X +Extraiga el tapn de precarga (5). +Withdraw the spring (6).
X
X +Extraiga el resorte (6).
X Move the fork to the end-of-stroke, insert a calibrated
X Lleve hasta el tope la carrera de la horquilla, introduz- dipstick (metre) in one of the fork tubes and make sure
ca una varilla calibrada (metro) en la barra y controle that 140 mm of air remain between the upper edge of
que queden 140 mm de aire desde el borde superior the fork and the oil.
de la barra hasta el nivel del aceite 140. X +If necessary, top up, see 1.7 (LUBRICANT CHART).
X + Si es necesario restaure el nivel del aceite, vase
1.7 (TABLA DE LOS LUBRICANTES).
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES) y 2.25 (HORQUILLA DELAN- TION) and 2.25 (FRONT FORK) carefully.
TERA).
X Remove the front mudguard, see 7.1.6 (REMOVING
X Extraiga el guardabarros delantero , vase 7.1.6 THE FRONT MUDGUARD UNIT).
(DESMONTAJE GRUPO GUARDABARROS DELAN- X Remove the front wheel, see 7.2.1 (DISASSEMBLY).
TERO).
X Extraiga la rueda delantera, vase 7.2.1 (DESMON- For the removal of the whole fork (in case of replace-
TAJE). ment), keep to the instructions, see 7.7.1 (DISASSEM-
BLY).
Para la extraccin de la horquilla completa (en caso de
sustitucin) lea con cuidado las instrucciones, vase
7.7.1 (DESMONTAJE).
7 - 79
&,&/,67,&$
Non azionare la leva freno anteriore dopo aver 2
rimosso la pinza freno, altrimenti il pistoncino
della stessa potrebbe fuoriuscire dalla sede,
causando la perdita del liquido freni.
7 - 80
3$57(&,&/2 &+$66,63$576
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES) y 2.25 (HORQUILLA DELAN- TION) and 2.25 (FRONT FORK) carefully.
TERA).
X Remove the front wheel, see 7.2.1 (DISASSEMBLY).
X Extraiga la rueda delantera, vase 7.2.1 (DESMON- X (For the left wheel-holder tube only)
TAJE). Unscrew and remove the two screws (1) that fasten
X (Slo para el grupo barra-botella izquierdo). the brake caliper (2) and take the two washers.
Destornille y quite los dos tornillos (1) de sujecin pin-
za freno (2) y guarde las correspondientes arandelas. Do not pull the front brake lever after remov-
ing the brake caliper, since the pin may go out
No accione la palanca freno delantero tras ha- of its seat, thus causing the outflow of the
ber extrado la pinza del freno, porque en caso brake fluid.
contrario el mbolo de la pinza podra salirse
de su alojamiento causando la prdida del lquido fre- X (For the left wheel-holder tube only)
no. Remove the brake caliper (2) (without disconnecting
the brake fluid pipe).
X (Slo para el grupo barra-botella izquierdo) X +Loosen the plug (3).
Extraiga la pinza del freno (2) (sin desconectar el tubo
lquido freno). Plug (3) driving torque: 20 Nm (2 kgm).
X +Afloje el tapn (3). X +Unscrew the screw (4).
Par de apriete tapn (3): 20 m (2 kgm) Screw (4) driving torque: 50 Nm (5 kgm).
X +Destornille el tornillo (4).
Par de apriete tornillo (4): 50 Nm (5 kgm)
X +Destornille los dos tornillo (5). X +Unscrew the two screws (5).
Par de apriete tornillos (5): 50 Nm (5 kgm) Screw (5) driving torque: 50 Nm (5 kgm).
X +Extraiga el grupo barra (6) junto con la botella (7) de X + Withdraw the wheel-holder tube (6) complete with
la placa superior (8) y de la placa inferior (9). slider (7) from the upper plate (8) and from the lower
plate (9).
7 - 81
&,&/,67,&$
Pericolo di fuoriuscita olio. 4
Il gruppo stelo portaruota - fodero carico
dolio.
Non capovolgerlo, o inclinarlo eccessivamente, nella 5
rimozione.
Nel rimontaggio posizionare lanello seeger
(12) con lo spigolo vivo in battuta (vedi figu- 12
ra).
- la guarnizione di tenuta (13); 10
- la boccola di guida (14);
- la boccola di scorrimento (15);
- il distanziale (16);
9
- laltra boccola di scorrimento (15).
8
7
7 - 82
3$57(&,&/2 &+$66,63$576
carefully.
La barra portarueda derecha e izquierda tie-
nen los mismos componentes en el interior. The right and left fork tubes have the same in-
Por lo tanto, las operaciones son vlidas para ambos. ner components. The operations described
below are therefore valid for both tubes.
X Desmonte el grupo barra-botella, vase 7.8.3 (DES-
MONTAJE GRUPO BARRA-BOTELLA (CON HOR- X Remove the wheel-holder tube/slider unit, see 7.8.3
QUILLA INSTALADA)) (con horquilla instalada). (REMOVING THE WHEEL-HOLDER TUBE/SLIDER
UNIT (WITH INSTALLED FORK)).
Peligro de salida aceite.
El grupo barra-botella est lleno de aceite. Warning! The oil may flow out.
Al extraerlo no lo revolque ni lo incline excesi- The wheel-holder tube/slider unit is full of oil.
vamente. Neither overturn it, nor incline it excessively
during the removal.
X Destornille y quite el tapn (1) y guarde la junta trica
(2). X Unscrew and remove the plug (1) and take the O-ring
X Extraiga segn el siguiente orden: (2).
- anillo portaresorte (4); X Withdraw the following parts in the given order:
- tubo de precarga (5); - spring holder ring (4);
- tubo de gua del resorte (6). - preload tube (5);
X Prepare un recipiente graduado con capacidad mni- - spring guide tube (6).
ma de 450 cm!. X Prepare a graduated container with at least 450 cm!
X Introduzca del todo la barra en la botella, revolque el capacity.
grupo barra-botella y descargue el aceite en el reci- X Make the tube get into the slider completely, overturn
piente. the tube/slider unit and drain the oil in the container.
X Destornille y quite el tornillo (7) y guarde la arandela X Unscrew and remove the screw (7) and take the seal-
de retencin (8). ing washer (8).
Par de apriete tornillo (7): 50 Nm (5 kgm) Screw (7) driving torque: 50 Nm (5 kgm).
X Quite segn el orden la barra portarueda (9) y el resor- X Withdraw first the wheel-holder tube (9) and then the
te (10). spring (10).
X Extraiga segn el orden: X Remove the following parts in the given order:
- junta rascapolvo (11); - antidust gasket (11);
- anillo Seeger (12); - retaining ring (seeger) (12);
Durante el reensamblaje coloque el anillo Upon reassembly, position the retaining
Seeger (12) con la arista viva contra el alo- ring (seeger) (12) with its sharp edge rest-
jamiento de la horquilla (vase figura). ing on the adjacent elements (see figure).
- retn (13); - seal (13);
- casquillo de gua (14); - guide bush (14);
- casquillo de deslizamiento (15); - slide bush (15);
- distanciador (16); - spacer (16);
- otro casquillo de deslizamiento (15). - the other slide bush (15).
7 - 83
&,&/,67,&$
STELO PORTARUOTA
X Controllare la superficie di scorrimento che non deve
presentare rigature e/o scalfitture. Le rigature appena
accennate possono essere eliminate carteggiando
con carta abrasiva, (a grana 1) bagnata.
Se le rigature sono profonde, sostituire lo stelo.
X Utilizzando un comparatore controllare che l'eventuale
curvatura dello stelo sia inferiore al valore limite.
Se supera il livello limite, sostituire lo stelo.
Limite di curvatura: 0,2 mm
Uno stelo incurvato non deve essere MAI rad-
drizzato in quanto la struttura ne verrebbe in-
debolita rendendo pericoloso l'utilizzo del vei-
colo.
FODERO
X Controllare che non vi siano danneggiamenti e/o fes-
surazioni; nel qual caso, sostituirlo.
MOLLA
X Controllare l'integrit della molla, verificando la lun-
ghezza che deve essere entro il valore limite.
Prima di effettuare la misurazione, battere la
molla per alcune volte sopra un piano pulito
per farla rinvenire.
Lunghezza della molla libera: 430 4 mm
7.8.6 RIMONTAGGIO
X Allineare perfettamente la piastra superiore con la pia-
stra inferiore.
Nel rimontaggio porre la massima attenzione
e controllare che le superfici di scorrimento
siano in perfetto stato, (non ci devono essere
segni di usura, rigature, ecc.), altrimenti sostituire il
componente.
Prestare la massima attenzione affinch corpi
estranei non entrino all'interno.
Non riutilizzare l'olio scaricato in precedenza.
Sostituire sempre le guarnizioni.
X +Il fodero deve essere inserito nella piastra superiore
fino a che il margine superiore sia allineato con il bor-
do superiore della piastra stessa.
X + Dopo il rimontaggio, immettere dal foro superiore
430 cm! (stelo destro e stelo sinistro) di olio, vedi 1.7
(TABELLA LUBRIFICANTI).
X + Effettuare il controllo livello olio, vedi 7.8.1 (CON-
TROLLO LIVELLO OLIO).
X + Portare lo stelo portaruota alla sua massima esten-
sione.
X + Rimettere il tappo superiore (1) con relativa guarni-
zione OR.
Dopo il rimontaggio, azionare il freno anterio-
re e spingere ripetutamente sulla forcella.
Il funzionamento deve essere dolce e progres-
sivo e non devono rimanere tracce dolio sugli steli.
7 - 84
3$57(&,&/2 &+$66,63$576
NUNCA enderece una barra curvada, en cuan- NEVER straighten a curved fork tube, since its
to la estructura puede debilitarse, volviendo structure would be weakened, thus making
peligroso el uso de vehculo. the use of the vehicle quite dangerous.
BOTELLA SLIDER
X Controle que no est daada y/o fisurada; si as fuera, X Make sure that there are neither damages, nor cracks.
sustityala. Otherwise, change it.
MUELLE SPRING
X Controle la integridad del muelle, verificando la longi- X Check the soundness of the spring, making sure that
tud que debe estar dentro del valor lmite. its length is within the limit value.
Antes de medir, golpee el muelle algunas ve- Before taking the measurement, strike the
ces contra un plano limpio para hacerlo reve- spring several times on a hard clean surface,
nir. in order to make it recover its original shape.
Longitud del muelle libre: 430 4 mm Length of the free spring: 430 4 mm
Upon reassembly, pay the greatest attention
Durante el montaje, controle que las superfi-
and make sure that the sliding surfaces are
cies de deslizamiento estn en perfectas con-
in perfect conditions (there must be no signs
diciones (no deben tener seales de desgas-
of wear, lines, etc.); otherwise, change the compo-
te, rayas, etc.) en caso contrario, sustituya el
nent.
componente.
Durante la instalacin tenga cuidado con que Avoid any accidental introduction of foreign
no entren cuerpos extraos en el interior. matters.
No utilice otra vez el aceite descargado ante- Do not reuse the oil that was drained previ-
riormente. ously.
Sustituya siempre las juntas.
Always change the gaskets.
X + La botella tiene que introducirse en la placa supe-
X +The slider must be inserted in the upper plate until its
rior, hasta que el margen superior quede alineado con
upper edge is aligned with the upper edge of the plate
el borde superior de la placa misma.
itself.
X + Tras la instalacin, introduzca por el agujero supe-
X +After reassembly, pour 430 cm 3 of oil (right and left
rior 430 cm! de aceite (barra derecha y barra izquier-
tube) through the upper hole, see 1.7 (LUBRICANT
da), vase 1.7 (TABLA DE LOS LUBRICANTES).
CHART).
X +Controle el nivel del aceite, vase 7.8.1 (CONTROL
X +Check the oil level, see 7.8.1 (CHECKING THE OIL
NIVEL ACEITE).
LEVEL)
X +Lleve la barra a su extensin mxima.
X +Extend the wheel-holder tube as much as possible.
X +Vuelva a colocar el tapn superior (1) con la corres-
X +Put back the upper plug (1) and the relevant O-ring.
pondiente junta trica.
Una vez concluido el montaje, accione el fre- After reassembly, pull the front brake lever
no delantero y empuje varias veces sobre la and push the fork down repeatedly.
horquilla. The operation must be gentle and progressive
El funcionamiento tiene que ser suave y progresivo and no traces of oil should remain on the fork tubes.
y, no deben quedar restos de aceite sobre las barras.
7 - 85
&,&/,67,&$
)25&(//21(3267(5,25(
7.9.1 RIMOZIONE
7
Per rendere pi agevole lo sfilamento della
vite (7) sollevare leggermente il forcellone.
6
Coppia di serraggio dado (6): 50 Nm (5 kgm)
7 - 86
3$57(&,&/2 &+$66,63$576
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES) y 2.26 (HORQUILLA TRASE- TION) and 2.26 (REAR FORK).
RA).
X Position the vehicle on the centre stand - or on an
X Coloque el vehculo sobre el caballete central - o apposite support stand fixed to the centre stand cou-
sobre un especial caballete de sostn fijado en los pi- plings.
votes del caballete central. X Loosen and remove the nut (1) that joins the pedal (2)
X Afloje y quite la tuerca (1) de unin pedal (2) bomba and the rear brake pump (3).
freno trasero (3). X Unscrew and remove the two screws (4), taking the
X Destornille y quite los dos tornillos (4) y guarde las co- relevant nuts.
rrespondientes tuercas. Screw/nut (4) driving torque:
Par de apriete tornillos/tuercas (4): 12 Nm (1.2 kgm).
12 Nm (1,2 kgm) X Temporarily fix the tank and the rear brake pump to the
X Sujete provisionalmente al basculante el depsito y la rear fork.
bomba freno trasero. X Remove the sides, see 7.1.4 (REMOVING THE
X Desmonte los paneles laterales, vase 7.1.4 (DES- RIGHT AND LEFT SIDES).
MONTAJE PANELES LATERALES DERECHO E IZ- X Open the two tangs (5) on the shock absorber upper
QUIERDO). support and release the brake pipe.
X Abra las dos lengetas (5) sobre el soporte superior X Loosen and remove the nut (6).
del amortiguador y suelte el tubo freno.
X Withdraw the screw (7) and take the washer.
X Afloje y quite la tuerca (6).
X Quite el tornillo (7) y guarde la arandela. To facilitate the withdrawing of the screw (7),
slightly raise the rear fork.
Para facilitar la extraccin del tornillo (7) le-
vante un poco el basculante. Nut (6) driving torque: 50 Nm (5 kgm)
preload hydraulic adjustment -, release the
En la versin con suspencin trasera dotada handwheel (8) by loosening the two nuts and with-
de ajuste hidrulico de precarga -, suelte el draw the two fastening screws, taking the two spac-
volante (8) aflojando las dos tuercas y quite los dos ers.
tornillos de sujecin guardando los correspondien-
tes distanciadores. X Remove the transmission pinion protection case, see
3.1.3 (REMOVING THE TRANSMISSION PINION
X Quite el crter de proteccin pin de transmisin, PROTECTION CASE).
vase 3.1.3 (DESMONTAJE CARTER PROTECCION X Remove the stop ring (9).
PION TRANSMISION).
X Withdraw the transmission pinion (10) complete with
X Quite el anillo de seguridad (9). chain from the shaft.
X Quite del eje el pin de transmisin (10) junto con la
cadena. If it is difficult to withdraw the transmission
pinion (10), slightly slacken the chain, see
Si la operacin de extraccin del pin de 2.16.3 (ADJUSTMENT).
transmisin (10) resulta algo difcil, afloje un
poco la tensin de la cadena, vase 2.16.3 (AJUSTE). X Remove the transmission pinion (10).
on the inner toothing of the transmission pi-
Durante la instalacin aplique sobre el denta- nion (10).
do interior del pin de transmisin (10) LOC-
TITE Anti-Seize.
7 - 87
&,&/,67,&$
NOTA (Y)
Da questo punto in poi, nella reinstallazione for-
cellone, procedere con le specifiche procedure, vedi
7.9.4 (REINSTALLAZIONE).
7 - 88
3$57(&,&/2 &+$66,63$576
X Afloje y quite la tuerca (11) y guarde la arandela. X Loosen and remove the nut (11) and take the washer.
X Quite el tornillo (12) y guarde la arandela. X Withdraw the screw (12) and take the washer.
NOTA (Y)
Desde este punto en adelante, durante la ins-
talacin del basculante, siga con los procedimientos
NOTE (Y)
For the reassembly of the rear fork, from this
point onwards proceed with the specific procedures,
especficos, vase 7.9.4 (INSTALACION). see 7.9.4 (REASSEMBLY).
X Bloquee la tuerca (13) y destornille de unos giros el X Lock the bush (13) and loosen the pin (14).
perno (14). X Lock the bush (13), unscrew and remove the lock ring
X Bloquee el casquillo (13), destornille y quite el casqui- (15) by means of the apposite socket spanner, see 1.8
llo de sujecin (15) con la correspondiente llave tubu- (SPECIAL TOOLS), then take the washer.
lar, vase 1.8 (EQUIPOS ESPECIALES), guardando X Unscrew the pin completely.
luego la arandela.
X Destornille completamente el perno.
Support the rear fork and of the shock absorb-
er on their front part.
Coloque, en la parte delantera, un soporte por
debajo del basculante y del amortiguador. X Withdraw and remove the pin (14) and take the wash-
ers.
X Extraiga el perno (14) y guarde las arandelas. X Remove the rear fork complete with wheel, suspension
X Quite el basculante junto con la rueda, el grupo sus- unit and brake unit.
pensin y el grupo freno.
Lea con mucho cuidado 1.4 (PRECAUCIONES E IN- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
FORMACIONES GENERALES). TION) carefully.
The bearings must be checked and if neces-
Despus de cada desmontaje controle los co- sary changed every time they are disassem-
jinetes y, si es necesario, sustityalos. bled.
X + Con un trapo limpie los dos lados del alojamiento de X + Clean the two sides of the bearing seat with a cloth.
los cojinetes. X + Remove the seal (15).
X + Quite el retn (15). X Hit on an apposite punch (with diameter equal to the
X Golpear sobre una herramienta adecuada (que tenga outer ring of the bearings) resting on the outer ring of
un dimetro igual al anillo exterior de los cojinetes) the bearing (18).
apoyada contra el anillo exterior del cojinete (18), em- X Push out (from the outside towards the inside):
puje hacia afuera (desde el exterior hasta el interior), - + the bush (16);
en el siguiente orden: - + the seal (17);
- + el casquillo (16) - + the bearings (18).
- + el retn (17)
X + Thoroughly clean the inside of the bearing seat.
-+ los cojinetes (18).
+ Limpie muy bien el interior del alojamiento de los co-
X
jinetes. Wash all the components with a clean deter-
gent.
7 - 89
&,&/,67,&$
7.9.3 CONTROLLO
Controllare che tutti i componenti non presen-
tino deformazioni, rotture, incrinazioni e/o am-
maccature evidenti. Sostituire tutti i compo-
nenti danneggiati.
CUSCINETTI
X Girare manualmente i rullini che devono ruotare dolce-
mente, senza impedimenti e/o rumorosit.
Non si devono riscontrare giochi assiali.
I cuscinetti che presentano questi inconvenienti devo-
no essere sostituiti.
PERNO FORCELLONE
3
Con un comparatore controllare che l'eccentricit del per-
no non superi il valore limite.
In caso contrario sostituire il perno.
7.9.4 REINSTALLAZIONE
Nella prima fase, il perno (1), la bussola di re-
gistrazione (2) e la ghiera di bloccaggio (3) de-
vono essere avvitati a mano.
Da questo punto in poi procedere con la rein-
stallazione in modo inverso alla rimozione par-
tendo dalla NOTA (Y), vedi 7.9.1 (RIMOZIONE).
7 - 90
3$57(&,&/2 &+$66,63$576
Controle que ningn componente est defor- Make sure that none of the components
mado, roto, con grietas y/o golpes evidentes. shows deformations, breaks, cracks and/or
Sustituya todos los componentes daados. evident dents.
Replace all the damaged components.
COJINETES BEARINGS
X Gire manualmente los rodillos, los cuales tienen que X Manually rotate the rollers, which must turn smoothly
girar suavemente, sin bloquearse ni hacer ruido. and noiselessly.
No deben notarse desajustes. No axial clearances should be noticed.
Hay que sustituir los cojinetes que muestren tales in- The bearings showing these defects must be changed.
convenientes.
Excentricidad mxima del perno: 0,3 mm Max. eccentricity of the pin: 0.3 mm.
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES). TION) carefully.
En la primera fase, el perno (1) la tuerca de In the first phase, the pin (1), the adjusting bush (2)
ajuste (2) y el casquillo de sujecin (3) tienen and the lock ring (3) must be screwed by hand.
que ser atornillados manualmente.
X Introduce and screw the pin (1) that fastens frame,en-
X Inserte y atornille el perno (1) de sujecin bastidor/mo- gine and rear fork, holding the adjusting bush (2) by
tor/basculante, manteniendo bloqueado la tuerca de means of the apposite socket spanner, see 1.8 (SPE-
ajuste (2) y empleando la correspondiente llave tubu- CIAL TOOLS).
lar, vase 1.8 (EQUIPOS ESPECIALES). X Screw the adjusting bush (2) until it reaches the end of
X Atornille la tuerca de ajuste (2) hasta llegar al tope so- stroke on the rear fork, then give it another one fourth
bre el basculante, luego atornllelo an de 1/4 de giro. turn.
Apriete tuerca de ajuste (2): tope + 1/4 de giro Tightening of the adjusting bush (2):
X Manteniendo bloqueado la tuerca de ajuste (2), apriete contact + one fourth turn.
el perno del basculante (1). X Hold the adjusting bush (2) and tighten the rear fork
Par de apriete perno (1): 100 Nm (10 kgm) pin (1).
X Vuelva a instalar la arandela. Pin (1) driving torque: 100 Nm (10 kgm).
X Bloquee la tuerca de ajuste (2) y, a la vez, atornille el X Put back the washer.
casquillo de sujecin (3). X Lock the adjusting bush (2) and at the same time
Par de apriete casquillo de sujecin (3): screw the lock ring (3).
100 Nm (10 kgm) Lock ring (3) driving torque:
100 Nm (10 kgm).
Desde este punto en adelante siga con la ins-
talacin actuando en sentido contrario con From this point onwards, proceed with the re-
respecto al desmontaje, partiendo de la NOTA assembly starting from NOTE (Y), see 7.9.1
(Y), vase 7.9.1 (DESMONTAJE). (REMOVAL) and following the reverse order
with respect to the removal.
7 - 91
&,&/,67,&$
6263(16,21(3267(5,25(
7.10.1 RIMOZIONE
Nel serraggio della vite (1) non superare la
coppia indicata perch si fissa direttamente
sullammortizzatore.
7 - 92
3$57(&,&/2 &+$66,63$576
Lea con cuidado 1.4 (PRECAUCIONES E INFORMA- Read 1.4 (PRECAUTIONS AND GENERAL INFORMA-
CIONES GENERALES) y 2.27 (SUSPENSIN TRASE- TION) and 2.27 (REAR SUSPENSION) carefully.
RA).
X Remove the rear fork complete with wheel, suspension
X Extraiga el basculante junto con la rueda, el grupo sus- unit and brake unit, see 7.9.1 (REMOVAL).
pensin y el grupo freno , vase 7.9.1 (DESMONTA- X Unscrew and remove the screw (1) and take the wash-
JE). er.
X Destornille y quite el tornillo (1) y guarde la arandela.
When tightening the screw (1), do not exceed
Durante el apriete del tornillo (1) no supere el the indicated torque, since it is fixed directly
par indicado porque se fija directamente en el onto the shock absorber.
amortiguador.
Any damage to the thread inevitably makes the re-
Un eventual dao a la rosca supone la inmediata sus- placement of the whole shock absorber necessary.
titucin del amortiguador completo.
Screw (1) driving torque: 50 Nm (5 kgm).
Par de apriete tornillo (1): 50 Nm (5 kgm)
X + Loosen and remove the nut (2).
X + Afloje y quite la tuerca (2). X + Withdraw the screw (3) and take the washer.
X + Extraiga el tornillo (3) y guarde la arandela.
The screw (3) on the left side of the vehicle is
longer than the screw on the right side of the
El tornillo (3) en el lado izquierdo del vehculo vehicle.
es ms largo del tornillo en el lado derecho.
Nut/screw (2-3) driving torque: 80 Nm (8 kgm).
Par de apriete tuerca/tornillo (2-3): 80 Nm (8 kgm)
X Loosen and remove the nut (4) and take the washer.
X Afloje y quite la tuerca (4) y guarde la arandela. X Withdraw the screw (5) and take the washer.
X Quite el tornillo (5) y guarde la arandela. Nut/screw (4-5) driving torque: 80 Nm (8 kgm).
Par de apriete tuerca/tornillo (4-5): 80 Nm (8 kgm) X + Remove the single connecting rod (6).
X + Desmonte la biela simple (6). X Withdraw all the inner components in the given order
X Extraiga segn el orden todos los componentes inte- (A-B).
riores (A - B). X + Withdraw all the inner components in the given order
X + Extraiga segn el orden todos los componentes inte- (C-D).
riores (C - D). X Thoroughly clean the inside of the bearing seats.
X Limpie muy bien el interior de los alojamientos de los
cojinetes.
Wash all the components with a clean deter-
gent.
Lave todos los componentes con detergente
limpio.
7 - 93
&,&/,67,&$
7.10.2 CONTROLLO
Controllare che tutti i componenti non presen-
tino deformazioni, rotture, incrinazioni e/o am-
maccature evidenti.
Sostituire tutti i componenti danneggiati.
CUSCINETTI
X Girare manualmente i rullini che devono ruotare dolce-
mente, senza impedimenti e/o rumorosit.
Non si devono riscontrare giochi assiali.
I cuscinetti che presentano questi inconvenienti devo-
no essere sostituiti.
AMMORTIZZATORE
7.10.3 RIMONTAGGIO
7 - 94
3$57(&,&/2 &+$66,63$576
Controle que ningn componente est defor- Make sure that none of the components
mado, roto, con grietas y/o golpes evidentes. shows deformations, breaks, cracks and/or
Sustituya todos los componentes daados. evident dents. Replace all the damaged com-
ponents.
COJINETES BEARINGS
X Gire manualmente los rodillos, los cuales tienen que X Manually rotate the rollers, which must turn smoothly
girar suavemente, sin bloquearse ni hacer ruido. and noiselessly.
No deben notarse desajustes. No axial clearances should be noticed.
Hay que sustituir los cojinetes que muestren tales in- The bearings showing these defects must be changed.
convenientes.
Controle que el amortiguador no pierda aceite y que su Make sure that there are no oil leaks from the shock ab-
carrera sea suave y progresiva. sorber and that its travel is smooth and progressive.
En caso contrario, sustityalo. Otherwise, change the shock absorber.
Si es necesario, seguir con el ajuste, vase 2.27.1 If necessary, adjust the suspension, see 2.27.1 (AD-
(AJUSTE SUSPENSION TRASERA) y 2.27.2 (AJUSTE JUSTING THE REAR SUSPENSION) and 2.27.2 (AD-
SUSPENSION TRASERA DOTADA DE AJUSTE HI- JUSTING THE REAR SUSPENSION WITH PRELOAD
DRULICO DE PRECARGA -). HYDRAULIC ADJSUTMENT -).
7 - 95
&,&/,67,&$ 3$57(&,&/2 &+$66,63$576
7 - 96
1
7
INFORMAZIONI PER LE RIPARAZIONI
8
INFORMACIONES
PARA LAS REPARACIONES
REPAIRS
8 -1
INFORMAZIONI PER LE RIPARAZIONI
INFORMAZIONI
INDICE
PERGENERAL
LE RIPARAZIONI 8
INDICE
7 8.3 POSIZIONAMENTO
COMPONENTI ELETTRICI.................Pag. 8-32
8.4 CONTROLLO
IMPIANTO ELETTRICO ......................Pag. 8-34
8.4.1 VEDI 6.1.1 (CONTROLLO
8 TENSIONE DI RICARICA)..................Pag. 8-34
8.4.2 VEDI 6.1.2 (CONTROLLO
FUNZIONAMENTO A VUOTO
ALTERNATORE) ................................Pag. 8-34
8.4.3 VEDI 6.1.3 (CONTROLLO
CONTINUIT ALTERNATORE).........Pag. 8-34
8.4.4 VEDI 6.1.4 (CONTROLLO
REGOLATORE DI TENSIONE)..........Pag. 8-34
8.4.5 CANDELA
(MANCANZA DI SCINTILLA).............Pag. 8-34
8.4.6 VEDI 6.3 (CONTROLLO IMPIANTO
ELETTRICO DA CONNETTORE
CENTRALINA C.D.I.)..........................Pag. 8-34
8.5 DATI E SPECIFICHE TECNICHE ......Pag. 8-35
8.5.1 COMPONENTI MOTORE....................Pag. 8-35
8.5.2 COMPONENTI
CARBURATORE ................................Pag. 8-35
8.5.3 IMPIANTO ELETTRICO......................Pag. 8-35
8.5.4 ASSORBIMENTI .................................Pag. 8-36
8.5.5 IMPIANTO FRENANTE.......................Pag. 8-37
8.5.6 RUOTE ................................................Pag. 8-37
8.5.7 SOSPENSIONI ....................................Pag. 8-37
8.5.8 CAPACIT - CARATTERISTICHE
LIQUIDI ...............................................Pag. 8-37
8 -2
INFORMACIONES PARA LAS REPARACIONES REPAIRS
INFORMACIONES
REPAIRS
PARA LAS REPARACIONES
8
8.1 IDENTIFICACIN
DE LAS AVERAS ................................. Pag. 8-10
8.1 TROUBLE-SHOOTING ........................ Pag. 8-16 1
8.1.1 ENGINE............................................... Pag. 8-16
8.1.1 MOTOR ............................................... Pag. 8-10 8.1.2 CARBURETTOR................................. Pag. 8-19
8.1.2 CARBURADOR .................................. Pag. 8-13 8.1.3 RADIATOR ......................................... Pag. 8-19
8.1.3 RADIADOR ......................................... Pag. 8-13 8.1.4 ELECTRIC SYSTEM........................... Pag. 8-20
8.1.4 INSTALACIN ELCTRICA .............. Pag. 8-14
8.1.5 BATERA ............................................ Pag. 8-14
8.1.5 BATTERY ........................................... Pag. 8-20
8.1.6 BRAKES ............................................. Pag. 8-21
2
8.1.6 FRENOS ............................................. Pag. 8-15 8.1.7 CHASSIS ............................................ Pag. 8-21
8.1.7 PARTE CICLO .................................... Pag. 8-15
8.2 RUN, FASTENING, WIRING, CABLES
8.2 RECORRIDO, SUJECIN, CABLEADO,
CABLES Y TUBOS ............................... Pag. 8-22
8.2.1 TUBO DEL FRENO DELANTERO ..... Pag. 8-22
AND PIPES ........................................... Pag. 8-22
8.2.1 FRONT BRAKE PIPE ......................... Pag. 8-22
8.2.2 REAR BRAKE PIPE ........................... Pag. 8-23
3
8.2.2 TUBOS DEL FRENO TRASERO ....... Pag. 8-23 8.2.3 FUEL SYSTEM PIPES........................ Pag. 8-24
8.2.3 TUBOS DE LA INSTALACIN DE 8.2.4 COOLING SYSTEM PIPES
ALIMENTACIN ................................. Pag. 8-24 AND CABLES ..................................... Pag. 8-25
8.2.4 TUBOS, CABLES SISTEMA DE
REFRIGERACIN ............................... Pag. 8-25
8.2.5 SPEEDOMETER-ODOMETER
CABLE................................................. Pag. 8-26
4
8.2.5 CABLE TAQUMETRO- 8.2.6 ACCELERATOR CONTROL
CUENTAKILMETROS ...................... Pag. 8-26 CABLES .............................................. Pag. 8-27
8.2.6 CABLES DE MANDO 8.2.7 COLD START CONTROL CABLE ..... Pag. 8-28
DEL ACELERADOR ........................... Pag. 8-27
8.2.7 CABLE DE MANDO DEL STARTER . Pag. 8-28
8.2.8 CLUTCH CONTROL CABLE ............. Pag. 8-29
8.2.9 ENGINE OIL PIPES ............................ Pag. 8-30 5
8.2.8 CABLE DE MANDO 8.2.10 ENGINE OIL PAN
DEL EMBRAGUE ................................ Pag. 8-29 BREATHER PIPE ............................. Pag. 8-31
8.2.9 TUBOS DEL ACEITE DEL MOTOR... Pag. 8-30 8.2.11 CABLES OF ELECTRIC
8.2.10 TUBO DE PURGA DEL CRTER COMPONENTS ................................ Pag. 8-32
DEL MOTOR ..................................... Pag. 8-31
8.2.11 CABLES,
8.3 POSITION 6
OF ELECTRIC COMPONENTS.......... Pag. 8-36
COMPONENTES ELCTRICOS ...... Pag. 8-32
8.4 CHECKING
8.3 COLOCACIN DE LOS COMPONENTES
THE ELECTRIC SYSTEM ................... Pag. 8-38
ELCTRICOS ......................................... Pag. 8-36
8.4 CONTROL DE LA INSTALACIN
8.4.1 SEE 6.1.1 (CHECKING THE RECHARGING
VOLTAGE) .......................................... Pag. 8-38
7
ELCTRICA............................................ Pag. 8-38 8.4.2 SEE 6.1.2 (CHECKING
8.4.1 VASE 6.1.1 (CONTROL TENSIN DE THE ALTERNATOR
RECARGA).......................................... Pag. 8-38 LOADLESS OPERATION).................. Pag. 8-38
8.4.2 VASE 6.1.2 (CONTROL
DEL FUNCIONAMIENTO EN VACO DEL
ALTERNADOR)................................... Pag. 8-38
8.4.3 SEE 6.1.3 (CHECKING THE ALTERNATOR
CONTINUITY)...................................... Pag. 8-38
8.4.4 SEE 6.1.4 (VOLTAGE REGULATOR) Pag. 8-38
8
8.4.3 VASE 6.1.3 (CONTROL DE LA 8.4.5 SPARK PLUG (NO SPARK) .............. Pag. 8-38
CONTINUIDAD DEL ALTERNADOR) Pag. 8-38 8.4.6 SEE 6.3 (CHECKING THE ELECTRIC
8.4.4 VASE 6.1.4 SYSTEM FROM C.D.I. CONNECTOR)Pag. 8-38
(REGULADOR DE TENSIN) ............ Pag. 8-38
8.5 TECHNICAL DATA
8.4.5 BUJA (FALTA DE CHISPA).............. Pag. 8-38
AND SPECIFICATIONS ...................... Pag. 8-39
8.4.6 VASE 6.3 (CONTROL DE LA
INSTALACIN ELCTRICA DE 8.5.1 ENGINE COMPONENTS.................... Pag. 8-39
CONECTOR CENTRALITA C.D.I.) ..... Pag. 8-38 8.5.2 CARBURETTOR COMPONENTS...... Pag. 8-39
8.5.3 ELECTRIC SYSTEM........................... Pag. 8-39
8.5 DATOS Y ESPECIFICACIONES 8.5.4 ABSORPTIONS .................................. Pag. 8-40
TCNICAS .............................................. Pag. 8-39 8.5.5 BRAKING SYSTEM............................ Pag. 8-40
8.5.1 COMPONENTES DEL MOTOR.......... Pag. 8-39 8.5.6 WHEELS ............................................. Pag. 8-41
8.5.2 COMPONENTES 8.5.7 SUSPENSIONS .................................. Pag. 8-41
DEL CARBURADOR .......................... Pag. 8-39 8.5.8 CAPACITIES - CHARACTERISTICS
8.5.3 INSTALACIN ELCTRICA .............. Pag. 8-39 OF FLUIDS. ........................................ Pag. 8-41
8.5.4 ABSORCIONES.................................. Pag. 8-40
8.5.5 INSTALACIN DE FRENADO ........... Pag. 8-40
8.5.6 RUEDAS ............................................. Pag. 8-41
8.5.7 SUSPENSIONES ................................ Pag. 8-41
8.5.8 CAPACIDAD - CARACTERSTICAS
LQUIDOS............................................ Pag. 8-41
8 -3
INFORMAZIONI PER LE RIPARAZIONI
8.1.1 MOTORE
Per ulteriori informazioni vedi MANUALE DOFFICINA MOTORE N 933 (D-UK) / N 934 (I-E-F).
8 -4
INFORMAZIONI PER LE RIPARAZIONI
8 -5
INFORMAZIONI PER LE RIPARAZIONI
8 -6
INFORMAZIONI PER LE RIPARAZIONI
8.1.2 CARBURATORE
8.1.3 RADIATORE
8 -7
INFORMAZIONI PER LE RIPARAZIONI
8.1.5 BATTERIA
8 -8
INFORMAZIONI PER LE RIPARAZIONI
8.1.6 FRENI
8.1.7 CICLISTICA
8 -9
INFORMACIONES PARA LAS REPARACIONES
8.1.1 MOTOR
Para mayores informaciones vase MANUAL DE TALLER MOTOR N 933 (D-UK) / N 934 (I-E-F).
8 - 10
INFORMACIONES PARA LAS REPARACIONES
8 - 11
INFORMACIONES PARA LAS REPARACIONES
8 - 12
INFORMACIONES PARA LAS REPARACIONES
8.1.2 CARBURADOR
8.1.3 RADIADOR
8 - 13
INFORMACIONES PARA LAS REPARACIONES
8.1.5 BATERA
8 - 14
INFORMACIONES PARA LAS REPARACIONES
8.1.6 FRENOS
8 - 15
REPAIRS
8.1 TROUBLE-SHOOTING
8.1.1 ENGINE
For further information see ENGINE SERVICE MANUAL No 933 (D-UK) / No 934 (I-E-F).
8 - 16
REPAIRS
8 - 17
REPAIRS
8 - 18
REPAIRS
8.1.2 CARBURETTOR
8.1.3 RADIATOR
8 - 19
REPAIRS
8.1.5 BATTERY
8 - 20
REPAIRS
8.1.6 BRAKES
8.1.7 CHASSIS
8 - 21
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
A B E F
C D G H
B
E
C
H F
D G
8 - 22
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
A D
B C E
D
A
B E
8 - 23
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
A B E
C D F
A
E
C D
8 - 24
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
A C
B D
A C
B D
8 - 25
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
A C D
B E F
D
B E
8 - 26
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
C
D
8 - 27
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
A C
B D
D
C
A-B
8 - 28
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
E G
F H
F
G
8 - 29
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
I M
L N
I
M
8 - 30
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
O Q
P R
R
P
Q
O
8 - 31
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
8
7 9
10
3 4 5 6
11
12
2
17 16 15 14 13
8 - 32
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
22 23
21
24 25 26 27
20
19
28
18
29
32 31 30
8 - 33
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
8.4.1 Vedi 6.1.1 (CONTROLLO 8.4.1 Vase 6.1.1 (CONTROL DE 8.4.1 See 6.1.1 (CHECKING THE
TENSIONE DI RICARICA) LA TENSIN DE RECARGA) RECHARGING VOLTAGE)
8.4.2 Vedi 6.1.2 (CONTROLLO 8.4.2 Vase 6.1.2 (CONTROL DEL 8.4.2 See 6.1.2 (CHECKING THE
FUNZIONAMENTO A VUOTO FUNCIONAMIENTO EN ALTERNATOR LOADLESS
ALTERNATORE) VACO DEL ALTERNADOR) OPERATION)
8.4.3 Vedi 6.1.3 (CONTROLLO 8.4.3 Vase 6.1.3 (CONTROL DE 8.4.3 See 6.1.3 (CHECKING THE
CONTINUIT LA CONTINUIDAD DEL ALTERNATOR CONTINUITY)
ALTERNATORE) ALTERNADOR)
8.4.4 Vedi 6.1.4 (CONTROLLO 8.4.4 Vase 6.1.4 (CONTROL DEL 8.4.4 See 6.1.4 (CHECKING THE
REGOLATORE DI REGULADOR DE TENSIN) VOLTAGE REGULATOR)
TENSIONE)
8.4.5 CANDELA (mancanza di 8.4.5 BUJA (falta de chispa) 8.4.5 SPARK PLUG (NO SPARK)
scintilla)
Primer control: First check:
Primo controllo: Control de los fusibles. Check fuses.
Verifica fusibili. Control de la buja. Check spark plugs
Verifica candela. Control de los interruptores de las Check stop light switch and stop
Verifica interruttori luce stop e luce luces de freno y de la luz de freno. light.
stop.
8.4.6 Vedi 6.3 (CONTROLLO 8.4.6 Vase 6.3 (CONTROL DE LA 8.4.6 See 6.3 (CHECKING THE
IMPIANTO ELETTRICO DA INSTALACIN DEL ELECTRICAL SYSTEM
CONNETTORE CONECTOR DE LA FROM THE C.D.I. CONNEC-
CENTRALINA C.D.I.) CENTRALITA C.D.I.) TOR)
8 - 34
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
Tensione a vuoto alternatore: Tensin del alternador en vaco: Alternator loadless voltage:
Vedi 6.1.2 (CONTROLLO FUNZIO- Vase 6.1.2 (CONTROL DEL FUN- See 6.1.2 (CHECKING THE ALTER-
NAMENTO A VUOTO ALTERNATO- CIONAMIENTO EN VACO DEL AL- NATOR LOADLESS OPERATION).
RE). TERNADOR).
Indicatore temperatura liquido re- Indicador de temperatura del lqui- Coolant temperature indicator:
frigerante: do refrigerante: See 6.4.2 (CHECKING THE IN-
Vedi 6.4.2 (CONTROLLO STRU- Vase 6.4.2 (CONTROL DEL INS- STRUMENT).
MENTO). TRUMENTO).
8 - 35
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
Sensore bassa pressione olio mo- Sensor de la presin baja del acei- Engine low pressure sensor:
tore: te del motor: See 6.5 (CHECKING THE ENGINE
Vedi 6.5 (CONTROLLO SENSORE Vase 6.5 (CONTROL DEL SEN- LOW PRESSURE SENSOR).
PRESSIONE OLIO MOTORE). SOR DE LA PRESIN BAJA DEL
ACEITE DEL MOTOR).
8 - 36
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
8.5.6 RUOTE
8.5.6 RUEDAS 8.5.6 WHEELS
Cerchi:
Vedi 1.6 (CARATTERISTICHE TEC- Llantas: Rims:
NICHE). Vase 1.6 (CARACTERSTICAS See 1.6 (TECHNICAL CHARAC-
TCNICAS). TERISTICS).
Eccentricit cerchio:
Vedi 7.2.3 (CONTROLLO). Excentricidad llanta: Rim eccentricity:
Vase 7.2.3 (CONTROL). See 7.2.3 (CHECKING).
Eccentricit perno ruota:
Vedi 7.2.3 (CONTROLLO). Excentricidad perno de la rueda: Wheel pin eccentricity:
Vase 7.2.3 (CONTROL). See 7.2.3 (CHECKING).
Pneumatici:
Vedi 1.6 (CARATTERISTICHE TEC- Neumticos: Tyres:
NICHE) 7.4 (PNEUMATICI). Vase 1.6 (CARACTERSTICAS See 1.6 (TECHNICAL CHARAC-
TCNICAS) et 7.4 (NEUMTICOS). TERISTICS) and 7.4 (TYRES).
8.5.7 SOSPENSIONI
8.5.7 SUSPENSIONES 8.5.7 SUSPENSIONS
Vedi 1.6 (CARATTERISTICHE TEC-
NICHE). Vase 1.6 (CARACTERSTICAS See 1.6 (TECHNICAL CHARAC-
TCNICAS). TERISTICS).
8.5.8 CAPACIT -
CARATTERISTICHE LIQUIDI 8.5.8 CAPACIDAD - 8.5.8 CAPACITIES -
CARACTERSTICAS CHARACTERISTICS
Vedi 1.6 (CARATTERISTICHE TEC- LQUIDOS OF FLUIDS
NICHE) e 1.7 (TABELLA LUBRIFI-
Vase 1.6 (CARACTERSTICAS See 1.6 (TECHNICAL CHARAC-
CANTI).
TCNICAS) y 1.7 (TABLA DE LOS TERISTICS) and 1.7 (LUBRICANT
LUBRICANTES). CHART).
8 - 37
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
8 - 38
INFORMAZIONI PER LE RIPARAZIONI / INFORMACIONES PARA LAS REPARACIONES / REPAIRS
8 - 39