Professional Documents
Culture Documents
2018 Metal Cutting Metal Forming Metrology PDF
2018 Metal Cutting Metal Forming Metrology PDF
Production is a p
process of converting
g inputs
p in to
b
outputs it is a broader term.
BySKMondal
b
1 2 3
Speed feed
Speed, feed, and depth of cut IES2013 IES2001
Carbide tool is used to machine a 30 mm diameter For cutting of brass with singlepoint cutting tool
steel
t l shaft
h ft att a spindle
i dl speed
d off 1000 revolutions
l ti per on a lathe, tool should have
minute The cutting speed of the above turning
minute.
(a) Negativerakeangle
operation
p is:
(b) Positiverakeangle
k l
(a) 1000 rpm
( ) Zerorakeangle
(c) Z k l
(b) 1570 m/min
(d) Zerosidereliefangle
Z id li f l
(c) 94.2 m/min
Cutting speed, feed, and depth of cut for a turning operation (d) 47.1 m/min
4 5 6
16 17 18
For-2018 (IES,GATE & PSUs) Page 2 of 213 Rev.0
GATE2017(PI) IES 2012 IES2003
Statement(I):Negativerakeanglesarepreferredonrigidset
St t t(I) N ti k l f d i id t The
Th angle l off inclination
i li i off the
h rake
k face
f with
ih
Turning, drilling, boring and milling are upsforinterruptedcuttinganddifficulttomachine respect to the tool base measured in a plane
commonly used machining operations.
operations Among materials.
materials
perpendicular to the base and parallel to the width
these, the operation(s) performed by a single Statement(II):Negativerakeangledirectsthechipsontothe
machinedsurface of the tool is called
point cutting tool is (are) (a) Back rake angle
(a) Both Statement (I) and Statement (II) are individually
( ) turning
(a) t i t
true andd Statement
St t t (II) is
i the
th correctt explanation
l ti off (b) Side
S d rake
k angle l
Statement (I)
(b) drilling and milling only (b) Both
B h Statement
S (I) and
d Statement
S (II) are individually
i di id ll
(c) S
Side
de cutt
cuttingg edge aangle
ge
(c) turning and boring only true but Statement (II) is not the correct explanation of (d) End cutting edge angle
St t
Statement t (I)
(d) boring only (c) Statement (I) is true but Statement (II) is false
(d) Statement (I) is false but Statement (II) is true
19 20 21
(c) Strengthen tool edge ((a)) 5 Hz ((b)) 12 Hz ((c)) 100 Hz ((d)) 5500 Hz
22 23 24
IES2009 IES1993
The following tool signature is specified for a single In ASA System, if the tool nomenclature is 8655 ISRO2011
point cutting
p g tool in American system:
y 10152mm,
5 , then the side rake angle
g will be A cutting tool having tool signature as 10,
10 9,
9 6,
6 6,
6 8,
8 8,
8
10, 12, 8, 6, 15, 20, 3 (a) 5 (b) 6 (c) 8 (d) 10
g
2 will have side rake angle
Wh does
What d the
h angle l 12 represent??
((a)) Side cuttingedge
g g angle g (a) 10o (b) 9o (c) 8o (d) 2o
(b) Side rake angle
( ) Back
(c) k rake
k anglel
(d) Side
de cclearance
ea a ce aangle
ge
34 35 36
For-2018 (IES,GATE & PSUs) Page 4 of 213 Rev.0
GATE2008 GATE2001 GATE2011
In
I a single
i l pointi turningi tool,
l the
h side
id rake
k anglel A single point cutting tool with 12 rake angle is
During orthogonal cutting of mild steel with
and orthogonal rake angle are equal. is the used to machine a steel work p piece. The depth
p of
principal cutting edge angle and its range is a 10
10 rake angle tool,
tool the chip thickness ratio
cut, i.e. uncut thickness is 0.81 mm. The chip
0o 90o . The chip flows in the orthogonal plane.
plane
was obtained as 0.4. The shear angle (in thickness under orthogonal machining condition is
The value of is closest to degrees) evaluated from this data is 1.8 mm. The shear angle is approximately
(a) 00 (b) 450 ( )6
(a)6.53 (b)
(b)20.22
( ) 22
(a)
(c) 600 (d) 900 (c)22.94 (d)50.00 ((b)) 26
(c) 56
(d) 76
37 38 39
IES1994
GATE2017 The
Th following
f ll i parameterst determine
d t i the
th IES2014Conventional
IES2014 Conventional
In an orthogonal machining with a tool of 90 model of continuous chip p formation: A bar of 70 mm diameter is being cut
orthogonal rake angle, the uncut chip 1. True feed orthogonally and is reduced to 68 mm by a
thickness
h k is 0.2 mm. Theh chip
h thickness
h k cutting tool.
tool In case mean length of the chip is
2. Cutting velocity
68.9 mm, find the cutting ratio. Determine
fluctuates between 0.25 mm and 0.4 mm. 3 Chip thickness
3. shear
h angle
l also
l if the
h rake
k angle i 10o
l is
The ratio of the maximum shear angle to the
4. Rake angle
4 g of the cutting g tool.
minimum
i i shear
h angle
l during
d i machining
hi i is i [10Marks]
___________ The parameters which govern the value of shear
angle
l wouldld include
l d
Hint: length of uncut chip = D
(a) 1,2
1 2 and 3 (b) 1,31 3 and 4
40
(c) 1,2 and 4 (d) 2,3 and 4 41 42
GATE 2012
GATE2012 IES2004 IES2006
Details pertaining to an orthogonal metal cutting Considerthefollowingstatementswithrespectto
C id h f ll i i h Considerthefollowingstatements:
C id h f ll i
process are given below. thereliefangleofcuttingtool: 1. Alargerakeanglemeanslowerstrengthofthe
g g g
Chip thickness ratio 0.4 1.Thisaffectsthedirectionofchipflow cuttingedge.
Undeformed thickness 0 6 mm
0.6 2 Thisreducesexcessivefrictionbetweenthetool
2.Thisreducesexcessivefrictionbetweenthetool 2 Cuttingtorquedecreaseswithrakeangle.
2. Cuttingtorquedecreaseswithrakeangle
Rake angle +10 andworkpiece Whichofthestatementsgivenaboveis/arecorrect?
Cutting speed 2.5 m/s 3.Thisaffectstoollife (a) Only1 (b) Only2
Mean thickness of primary shear zone 25 microns 4 Thisallowsbetteraccessofcoolanttothetool
4.Thisallowsbetteraccessofcoolanttothetool ( ) Both1and2
(c) B th d (d) Neither1nor2
N ith
The shear strain rate in s1 during the process is workpieceinterface
(a) 0.1781105 (b) 0.7754105 Whichofthestatementsgivenabovearecorrect?
h h f h b
(c) 1.010410
1 0104105 4 397105
(d) 4.39710 (a) 1and2 (b) 2and3
49 (c) 2and4 (d) 3and4 50 51
55 56 57
( ) Shearplaneandthecuttingvelocity
(a)
(b) Shearplaneandtherakeplane
Sh l dth k l
(c) Shearplaneandtheverticaldirection
((d)) Shearplaneandthedirectionofelongationofcrystalsin
p g y
thechip
58 59 60
61 62 63
For-2018 (IES,GATE & PSUs) Page 7 of 213 Rev.0
GATE 2009(PI)CommonDataS2 GATE1995 IES2007
An
A orthogonal
h l turning
i operation
i is
i carried
i d out at 20 Duringmachining,excessmetalisremovedintheform
Duringmachining excessmetalisremovedintheform
Plainmillingofmildsteelplateproduces ofchipasinthecaseofturningonalathe.Whichofthe
m/min cutting speed,
speed using a cutting tool of rake angle followingarecorrect?
(a)Irregularshapeddiscontinuouschips
Continuousribbonlikechipisformedwhenturning
155o. The chip
p thickness is 0.4
4 mm and the uncut chip
p (b)Regularshapeddiscontinuouschip 1
1. Atahighercuttingspeed
thickness is 0.2 mm. (c)Continuouschipswithoutbuiltupedge 2. Atalowercuttingspeed
(d)Joinedchips 3. Abrittlematerial
The chip velocity (in m/min) is 4. Aductilematerial
4
Selectthecorrectanswerusingthecodegivenbelow:
(a) 8 (b) 10 (c) 12 (d) 14
(a) 1and3 (b) 1and4
(c) 2and3 (d) 2and4
64 65 66
67 68 69
GATE2009 IES1997
Friction at the toolchip interface can be reduced by Assertion (A): For high speed turning of cast iron
pistons, carbide tool bits are provided with chip
b k
breakers.
Analysis of Metal Cutting
(a) decreasing the rake angle
Reason (R): High speed turning may produce long,
ribbon type continuous chips which must be broken
(b) increasing the depth of cut into small lengths which otherwise would be
difficult to handle and may yp
prove hazardous.
( ) Decreasing the cutting speed
(c) (a) Both A and R are individually true and R is the
correct explanation
p of A
(d) increasing
i i the
h cutting
i speed
d (b) Both A and R are individually true but R is not the
correct explanation of A
(c) A is true but R is false
(d) A is false but R is true
B SKM d l
BySKMondal
70 71 72
For-2018 (IES,GATE & PSUs) Page 8 of 213 Rev.0
ESE2000(Conventional) LimitationsofuseofMCD GATE2010(PI)LinkedS1
The following data from the orthogonal cutting test In
I orthogonal
h l turning
i off an engineering
i i alloy,
ll it
i has
h
1. MCD is valid only for orthogonal cutting. been observed that the friction force acting at the chip
is available. Rake angle = 100, chip thickness ratio =
0.35, uncut chip thickness = 0.51 mm, width of cut = 2. By the ratio F/N, the MCD gives apparent (not actual)
tool interface is 402.5 N and the friction force is also
3 mm,
mm yield shear stress of work material = 285 perpendicular
p p to the cuttingg velocityy vector. The feed
coefficient of friction. velocity is negligibly small with respect to the cutting
N/mm2, mean friction coefficient on tool face =
0.65,
6 D
Determinei velocity The ratio of friction force to normal force
velocity.
associated with the chiptool interface is 1. The uncut
((i)) Cutting
g force ((Fc)
chip
hi thickness
thi k i 0.2 mm and
is d the
th chip
hi thickness
thi k i 0.4
is
(ii) Radial force mm. The cutting velocity is 2 m/s.
(iii) Normal
N l force
f (N) on tooll and
d The shear force (in N) acting along the primary shear
((iv)) Shear force ((Fs )). plane is
73 74 (a) 180.0 (b) 240.0 (c) 360.5 (d) 402.5 75
GATE 2015
GATE-2015 GATE 2017 (PI)
GATE2017(PI)
The Merchant circle diagram g showingg various forces MerchantTheoryorAnalysis
A single point cutting tool with 0 rake angle is associated with a cutting process using a wedge shaped
tool is given in the Figure. Assumption
p
used in an orthogonal machining process. At a The coefficient of Theworkmaterialbehaveslikeanidealplastics.
cutting speed of 180 m/min, the thrust force is 490 friction can be
estimated from Thetheoryinvolvesminimumenergyprincipal.
N If the coefficient of friction between
N. bet een the tool the
h ratioi s and areassumedtobeconstant,independentof
and the chip is 0.7, then the power consumption(in f f
(a) 1 (b) 3 I i b d i l h l h
Itisbasedonsingleshearplanetheory.
kW) for the machining
g operation
p is _____ f2 f4
f5 f6
(c ) (d )
f6 f5
79 80 81
For-2018 (IES,GATE & PSUs) Page 9 of 213 Rev.0
IAS 1999
FromMerchantTheoryorAnalysis
From Merchant Theory or Analysis
In an orthogonal cutting process, rake angle of the
y Merchant
M h t theory
th gives
i hi h
higher shear
h plane
l tooll is 20 and
d friction
f angle
l is 25.5. Using
((a)) 39
39.5
5 ((b)) 42.25
4 5
all of which mean easier machining ((c)) 47
47.75
75 ((d)) 550.5
5
82 83 84
( ) 60
(c) 6 (d) 40 Determine coefficient of friction at tool
toolchip
chip interface = 0.7.
07
((ii)) Cutting
g and thrust component
p of the force. is
85 86
(a) 20.5 (b) 24.5 (c) 28.5 (d) 32.5 87
(c) 2
((d)) +
(Where = shear angle, = friction angle
and = rake angle)
91 92 93
IFS 2016
IFS2016 OtherRelations
TheoryofLeeandShaffer In a slab milling g operation
p g teeth
with straight
They applied the theory of plasticity for an cutter, the cutter has 15 teeth with 10o rake angle
and rotates at 200 rpm.rpm The diameter of the
ideal-rigid-plastic body.
cutter is 80 mm and table feed is 755 mm/min, the
They also assumed that deformation occured depth of cut is 5 mm, the width of slab is 50 mm y ByStabler
on a thin-shear
thi h zone. and ultimate shear stress of work material is 420
N/mm2. Assuming the coefficient of friction
And derive between chip and cutter to be 0.7 and using Lee
and Shaffer relation,
relation plot variation of resultant
= + torque and cutter rotation, and estimate average
4
power consumption.i
94 95 96
Fs = Fc cos Ft sin
F
and = = tan 97 98 99
N
For-2018 (IES,GATE & PSUs) Page 11 of 213 Rev.0
IES2000 GATE 2007(PI)CommonData1
( )
GATE2016 In an orthogonal machining test, test the following
In an orthogonal cutting test, the cutting force and observations were made
In an orthogonal cutting process the tool used has rake
thrust force were observed to be 1000N and 500 N Cutting force 1200 N
angle
g of zero degree.
g The measured cutting
g force and Thrust force 500 N
respectively. If the rake angle of tool is zero, the
thrust force are 500 N and 250 N, respectively. The Tool rake angle zero
coefficient of friction in chiptool
chip tool interface will
ill be
coefficient of friction between the tool and the chip is Cutting speed 1 m/s
1 1 Depth of cut 0 8 mm
0.8
(a)2 ( b)2 ( c) ( d) 2
________________
2 Chip thickness 1.5 mm
Friction angle during machining will be
22 6o (b) 32.8
(a) 22.6 32 8o (c) 57.1
57 1o 67 4o
(d) 67.4
100 101 102
GATE 2007(PI)CommonData2
( ) G
GATE 20 ( ) i k d S
2011(PI)LinkedS1 G
GATE 20 ( ) i k d S2
2011(PI)LinkedS2
In an orthogonal machining test, test the following During orthogonal machining of a mild steel specimen During orthogonal machining of a mild steel specimen
observations were made with a cutting tool of zero rake angle, the following data with a cutting tool of zero rake angle, the following data
Cutting force 1200 N i obtained:
is bt i d i obtained:
is bt i d
Thrust force 500 N Uncut chip p thickness = 0.25 mm Uncut chipp thickness = 0.25 mm
Tool rake angle zero Chip thickness = 0.75 mm Chip thickness = 0.75 mm
Cutting speed 1 m/s Width off cutt = 2.5 mm Width off cutt = 2.5 mm
Depth of cut 0 8 mm
0.8 Normal force = 95 950 N Normal force = 95950 N
Chip thickness 1.5 mm Thrust force = 475 N Thrust force = 475 N
Th shear
The h angle
l andd shear
h f
force, respectively,
ti l are Th lti t h t
Theultimateshearstress(inN/mm
(i N/ 2)ofthework
) fth k
Chip speed along the tool rake face will be
((a)) 771.565o
5 5 , 150.21
5 N ((b)) 18.435o
435 , 75
751.04
4N materialis
(a) 0.83
0 83 m/s (b) 0.53
0 53 m/s
(c) 9.218o, 861.64 N (d) 23.157o , 686.66 N (a)235 (b)139 (c)564 (d)380
(c) 1.2 m/s (d) 1.88 m/s 103 104 105
IFS 2012
IFS2012
An orthogonal machining operation is being carried out GATE2006CommonDataQuestions(1) GATE2006CommonDataQuestions(2)
under the following conditions : Inanorthogonalmachiningoperation: Inanorthogonalmachiningoperation:
depth of cut = 0.1 mm, Uncutthickness 0 5mm
Uncutthickness=0.5mm Uncutthickness 0 5mm
Uncutthickness=0.5mm
chip thickness = 0.2 mm, Cuttingspeed=20m/min Rakeangle=15 Cuttingspeed=20m/min Rakeangle=15
width of cut = 5 mm, Widthofcut=5mm Chipthickness=0.7mm Widthofcut=5mm Chipthickness=0.7mm
rake angle = 10o Thrustforce 200N
Thrustforce=200N Cuttingforce 1200N
Cuttingforce=1200N Thrustforce 200N
Thrustforce=200N Cuttingforce 1200N
Cuttingforce=1200N
Theforcecomponentsalongandnormaltothedirection AssumeMerchant'stheory. AssumeMerchant'stheory.
ofcuttingvelocityare500Nand200Nrespectively.
f i l i N d N i l
Thecoefficientoffrictionatthetoolchipinterfaceis Thepercentageoftotalenergydissipateddueto
Determine
(a)0 23
(a)0.23 (b)0 46
(b)0.46 frictionatthetool chipinterfaceis
frictionatthetoolchipinterfaceis
(i)Thecoefficientoffrictionbetweenthetoolandchip.
(c)0.85 (d)0.95 (a)30% (b)42%
(ii)Ultimateshearstressoftheworkpiecematerial [10]
(ii)Ultimateshearstressoftheworkpiecematerial.[10]
(c)58% (d)70%
106 107 108
For-2018 (IES,GATE & PSUs) Page 12 of 213 Rev.0
GATE2006CommonDataQuestions(3) T i O ti
TurningOperation y Fc or Fz or tangential component or primary cutting
force acting in the direction of the cutting velocity,
Inanorthogonalmachiningoperation: largest
l force
f andd accounts forf 99%% off the
h power
required by the process.
Uncutthickness 0 5mm
Uncutthickness=0.5mm
y Fx or axial component or feed force acting in the
Cuttingspeed=20m/min Rakeangle=15
direction of the tool feed.
feed This force is about 50% of
Widthofcut=5mm Chipthickness=0.7mm Fc, but accounts for only a small percentage of the
Thrustforce 200N
Thrustforce=200N Cuttingforce 1200N
Cuttingforce=1200N power required
i d because
b f d rates
feed t are usually
ll small
ll
AssumeMerchant'stheory. compared to cutting speeds.
Thevaluesofshearangleandshearstrain, y Fy or radial force or thrust force in turning acting
respectively are
respectively,are perpendicular to the machined surface. This force is
(a)30.3 and1.98 (b)30.3 and4.23 about 50% of Fx i.e. 25% of Fc and contributes very
little to power requirements because velocity in the
(c)40.2 and2.97 (d)40.2 and1.65
109 110 radial direction is negligible. 111
IES1999 f d f d h
DeterminationofUndeformedchip
The radial force in singlepoint tool during
ConversionFormula
Conversion Formula thicknessinTurning:(VIMP)
thickness in Turning: (VIMP)
turning operation varies between We have to convert turning (3D) to Orthogonal Forsinglepointcuttingtool
Cutting (2D)
((a)) 0.2 to 0.4
4 times the main cutting
g force t = f sin
(b) 0.4 to 0.6 times the main cutting force Fc = Fz
d
(c) 0.6 to 0.8 times the main cutting force F b=
Ft = Fxy =
Fx
= y = Fx2 + Fy2 Where sin
(d) 0.5 to
t 0.66 times
ti th main
the i cutting
tti force
f
sin cos t=Uncutchipthickness
f=feed
=90 Cs=approachangle
Cs=sidecuttingedgeangle
sidecuttingedgeangle
sin sin90
machining operation could be approximated to be The chip thickness obtained is 0.48 mm. If the
orthogonal
h l cutting.
i Th tangential
The i l cutting
i force
f and
d orthogonal rake angle is zero and the principal
thrust force were 1177 N and 560 N respectively.
Calculate: [30 marks]
t = f sin = f sin90 = f cutting edge angle is 90, the shear angle is
d
degree i
is
(i) The side rake angle (a) 20.56
.5 ((b)) 26.56
.5
d d
(ii) Coefficient of friction at the rake face b= = =d (c) 30.56 (d) 36.56
(iii) The dynamic shear strength of the work material
121
i sin90
sin i 90 122 123
GATE 2015
GATE-2015 GATE 2015
GATE-2015 GATE 2016
GATE2016
Orthogonal turning of mild steel tube with a tool For an orthogonal cutting operation, tool material is
An
A orthogonal
h l turning
i operation
i isi carried
i d out under
d
rake angle of 10 is carried out at a feed of 0.14 HSS, rake angle is 22o , chip thickness is 0.8 mm, speed
the following conditions: rake angle = 55, spindle
mm/rev. If the thickness of chip produced is 0.28 mm. is 48 m/min and feed is 0.4 mm/rev. The shear plane
rotational speed
p = 4
400 rpm,
p , axial feed = 0.4
4 m/min
/
The values of shear angle and shear strain is angle (in degree) is
and radial depth of cut = 5 mm. The chip thickness, tc
a) 2820 and 2.19
is found to be 3 mm . The shear angle (in degrees) in
b) and
b)2220 d 3.53
this turning process is _____
c) 24
2420
20 and 4.19
4 19
d)3720
37 and 55.19
9
124 125 126
For-2018 (IES,GATE & PSUs) Page 14 of 213 Rev.0
GATE2007 GATE2003CommonDataQuestions(1) GATE2003CommonDataQuestions(2)
In orthogonal turning of low carbon steel pipe with A cylinder is turned on a lathe with orthogonal A cylinder is turned on a lathe with orthogonal
machining principle.
principle Spindle rotates at 200 rpm.
rpm The machining principle.
principle Spindle rotates at 200 rpm.
rpm The
principal cutting edge angle of 90, the main cutting axial feed rate is 0.25 mm per revolution. Depth of cut is axial feed rate is 0.25 mm per revolution. Depth of cut is
force is 1000 N and the feed force is 800 N. The shear 0 4 mm.
0.4 mm The rake angle is 10 10. In the analysis it is found 0 4 mm.
0.4 mm The rake angle is 10 10. In the analysis it is found
that the shear angle is 27.75 that the shear angle is 27.75
angle is 25
2 and orthogonal rake angle is zero.
ero Thethicknessoftheproducedchipis Intheaboveproblem,thecoefficientoffrictionat
Employing Merchant
Merchantss theory, the ratio of friction (a)0 511mm
(a)0.511mm (b)0 528mm
(b)0.528mm thechiptoolinterfaceobtainedusingEarnestand
p g
(c)0.818mm (d)0.846mm Merchanttheoryis
force to normal force acting
g on the cutting
g tool is
(a)0 18
(a)0.18 (b)0 36
(b)0.36
((a)) 1.56
5 ((b)) 1.255 ((c)) 0.80 ((d)) 0.64
4 (c)0.71 (d)0.98
127 128 129
Where
Fc=cuttingforce(inN) Sometimes it is also known as specific power
DN
V tti
V=cuttingspeed=,m/s
d / consumption.
consumption
60
136 137 138
Example GATE2014
SpecificCuttingPressure
Specific Cutting Pressure The
Th main i cutting
i force
f acting
i on a tooll during
d i the
h
Whentherakeangleiszeroduringorthogonalcutting, turning (orthogonal cutting) operation of a metal is
showthat The cutting force, Fc, divided by the cross section
area of the undeformed chip gives the nominal 400 N. The turning was performed using 2 mm
s
=
(1 r ) r cutting stress or the specific cutting pressure,
pressure pc depth
p of cut and 0.1 mm/rev/ feed rate. The specific
p
pc 1+ r2 cutting pressure is
Wh s is
Where i the
h shear
h strengrhh off the
h material
i l Fc Fc (a) 1000
pc = specific
p ppower of cutting
g pc = = (b) 2000
r = chip thickness ratio bt fd
= coefficient of friction in tool chip interface
(c) 3000
(d) 4000
142 143 144
For-2018 (IES,GATE & PSUs) Page 16 of 213 Rev.0
FrictioninMetalCutting
l GATE1992 GATE1993
The effect of rake angle on the mean friction angle in The effect of rake angle on the mean friction angle in
machining can be explained by machining can be explained by
(A) sliding (Coulomb) model of friction (a) Sliding (coulomb) model of friction
(B) sticking and then sliding model of friction (b) sticking and then siding model of friction
((C)) sticking
g friction (c) Sticking friction
(D) Sliding and then sticking model of friction (d) sliding and then sticking model of friction
H Di ib i i M lC i
HeatDistributioninMetalCutting
IES2000 IES2004
Assertion
A i (A):
(A) The
Th ratioi off uncut chip
hi thickness
hi k to
Assertion (A): In metal cutting, the normal actual chip thickness is always less than one and is
laws of sliding friction are not applicable.
applicable termed d as cutting ratio in orthogonal
h l cutting
Reason ((R): ) Very y highg temperature
p is Reason ((R): ) The frictional force is veryy high
g due to the
produced at the toolchip interface. occurrence of sticking friction rather than sliding
friction
( ) Both
(a) h A and d R are individually
d d ll true andd R is (a) Both A and R are individually true and R is the correct
the correct explanation of A explanation of A
(b) Both A and R are individually true but R is (b) Both A and R are individually true but R is not the
not the correct explanation of A correct explanation
l i off A
(c) A is true but R is false
(c) A is true but R is false
(d) A is false but R is true
(d) A is false but R is true 148 149 150
IES2011 IES1993
Dynamometer Theinstrumentordeviceusedtomeasurethecutting A 'Dynamometer' is a device used for the
forcesinmachiningis:
g
y Dynamometers are used for measuring Cutting forces.
forces measurement of
(a)Tachometer
y For Orthogonal Cutting use 2D dynamometer ((a)) Chip
p thickness ratio
(b)Comparator
(b)C
y For Oblique
q Cutting
g use 33D dynamometer
y ( ) y
(c)Dynamometer
(b) Forces during metal cutting
(d)Lactometer (c) Wear of the cutting tool
(d) Deflection
D fl ti off the
th cutting
tti tool
t l
ToolFailure
ForPSU&IES
For PSU & IES Tool failure is two types
In strain gauge dynamometers the use of how y 1. Slowdeath: The g gradual or p
progressive
g wearingg
many active gauge makes the dynamometers more away of rake face (crater wear) or flank (flank wear) of
effective , ,
ToolWear,ToolLife,Economics& the cuttingg tool or both.
y 2.Suddendeath:Failuresleadingtoprematureend
(a) Four Machinability ofthetool
(b) Three y The suddendeath type of tool failure is difficult to
(c) Two predict. Tool failure mechanisms include plastic
deformation, brittle fracture, fatigue fracture or edge
(d) One pp g However it is difficult to p
chipping. predict which of
these processes will dominate and when tool failure
will occur.
BySKMondal
166 167 168
FlankWear:(Wearland) FlankWear:(Wearland)
Stages Primary wear
y Flank
Fl k Wear
W occurs in
i three
h stages off varying
i wear rates The region
Th i where
h the
h sharp
h cutting
i edge
d i quickly
is i kl
broken down and a finite wear land is established.
Secondary
y wear
The region where the wear progresses at a uniform rate.
y At very high
hi h speed
d crater
t wear predominates
d i t
VT n = C
((d)) Anyoftheabove
y [IAS1999;
[IAS 1999; IES
IES2006]
2006]
= 0.55 to 0.77 for ceramic tool
Where,V=cuttingspeed(m/min) [NTPC2003]
T Time(min)
T=Time(min)
n=exponentdependsontoolmaterial
C=constantbasedontoolandworkmaterialandcutting
202 condition. 203 Reference:Kalpakjian 204
ISRO2011 GATE2004,IES2000
GATE2009(PI)
GATE 2009 (PI) A 50 mm diameter steel rod was turned at 284 rpm and
In
I a machining
hi i operation,
i doubling
d bli
1
the
h cutting
i
speed reduces the tool life to 8 th of the original
I an orthogonal
In th l machining
hi i operation,
ti th tool
the t l life
lif tool failure occurred in 10 minutes. The speed was value. The exponent n in Taylor's tool life equation
obtained is 10 min at a cutting speed of 100 m/min,
m/min VTn = C,, is
changed
h d to 232 rpm and
d the
h tooll failed
f il d in
i 60
6 minutes.
i
1 1 1 1
while at 75 m/min cutting
g speed,
p the tool life is 330 Assuming straight line relationship between cutting (a) (b) (c ) (d )
8 4 3 2
min. The value of index (n) in the Taylors tool life speed
p and tool life,, the value of Taylorian
y Exponent
p is
equation
(a) 0.21 (b) 0.133 (c) 0.11 (d) 0.233
(a) 0.262 (b) 0.323 (c) 0.423 (d) 0.521
IFS2013
IFS 2013
GATE2009LinkedAnswerQuestions(1) GATE2009LinkedAnswerQuestions(2) In a metal cutting experiment, the tool life was
Inamachiningexperiment,toollifewasfoundtovary
I hi i i llif f d Inamachiningexperiment,toollifewasfoundtovary
I hi i i llif f d
withthecuttingspeedinthefollowingmanner: withthecuttingspeedinthefollowingmanner: found to vary with the cutting speed in the
Cuttingspeed(m/min) Toollife(minutes) Cuttingspeed(m/min) Toollife(minutes) following manner :
60 81 60 81 C i
Cuttingspeed,V(inm/min)
d V(i / i ) Toollife,T(inmin)
T llif T(i i )
90 36 90 36
100 120
Theexponent(n)andconstant(k)oftheTaylor's Whatisthepercentageincreaseintoollifewhen
toollifeequationare thecuttingspeedishalved? 130 50
(a)n=0.5andk=540 (b)n=1andk=4860 (a)50% (b)200% Derive Taylor's tool life equation for this operation
(c)n=1andk=0.74 (d)n0.5andk=1.15 (c)300% (d)400% and estimate the tool life at a speed of 2.5 m/s. Also
estimate the cutting speed for a tool life of 80 min.
223 224 225
For-2018 (IES,GATE & PSUs) Page 25 of 213 Rev.0
GATE2010 GATE2013 GATE 2017
GATE2017
Two cutting tools with tool life equations given
For tool A, Taylors tool life exponent (n) is 0.45 and Two cutting tools are being compared for a
below are being compared:
constant (K)
( ) is 90. Similarly
l l for
f tooll B, n = 0.3 and
dK machining
hi i operation.
ti Th tool
The t l life
lif equations
ti are:
Tool 1: VT0.1 = 150
= 60.
60 The cutting speed (in m/min) above which tool Carbide tool: VT 1.6 = 3000 Tool 2: VT0.3
0 3 = 300
A will have a higher tool life than tool B is HSS tool: VT 0.6 = 200 Where V is cutting speed in m/minute and T is
tool life in minutes. The breakeven cutting speed
((a)) 26.77 ((b)) 4
42.55 ((c)) 80.77 ((d)) 142.9
4 9 Where V is the cutting
g speed
p in m/min and T is the
b
beyond d which
hi h Tool
T l 2 will
ill have
h a higher
hi h tool
t l life
lif is
i
tool life in min. The carbide tool will provide higher ____ m/minute.
tool life if the cutting speed in m/min exceeds
(a) 15.0 (b) 39.4 (c) 49.3 (d) 60.0
226 227 228
Example
p GATE 2003
GATE2003
Thefollowingdatawasobtainedfromthetoollife g tools could p
A batch of 10 cutting produce 500 GATE2017
cuttingtest: During
D i the h turningi off a 20 mmdiameter
di steell bar
b
components while working at 50 rpm with a tool
at a spindle speed of 400 rpm, a tool life of 20
CuttingSpeed,m/min:49.74 49.23 48.67 45.76 42.58 feed of 0.25 mm/rev and depth of cut of 1 mm. A minute is obtained.
Toollife,min 2.94 3.90 4.77 9.87 28.27 similar batch of 10 tools of the same specification When the same bar is turned at 200 rpm, the tool
could
ld produce
d 122 components
t while
hil working
ki att 80
8 life becomes 60 minute. Assume that Taylor
Taylorss tool
DeterminetheconstantsoftheTaylortoollifeequation life equation is valid.
VTn =C
C rpm with a feed of 0.25
0 25 mm/rev and 1 mm depth of
When the bar is turned at 300 rpm, the tool life
cut. How many
y components
p can be p
produced with (in minute) is approximately
one cutting tool at 60 rpm? (a) 25 (b) 32 (c) 40 (d) 50
229 (a) 29 (b) 31 (c) 37 (d) 42 230 231
GATE2017(PI)
( ) IES 2016 Conventional
IES2016Conventional
GATE2016 In a machining operation with turning tool, the
Write the generalized Taylor's tool life
tool life (T) is related to cutting speed V (m/s),
(m/s)
The tool life equation for HSS tool is VT0.14 f 0.7 d0.4
feed f(mm) and depth of cut d (mm) as equation. Also write the simplified Taylor's
2.5
2 5 0 9 0
0.9 0.15
15 tool life equation.
equation
= C. The tool life (T) of 30 min is obtained using the T = Cv f d During g machining g of low carbon steel with
Where, C is
Wh i a constant.
t t The
Th suggested t d values
l f
for
following cutting conditions: V = 45 m/min, f = 0.35 HSS tool, the following observations have
the cutting gp parameters are: V = 1.55 m/s,, f = 0.255
mm, d = 2.0 mm. If speed (V),
( ) feed(f)
( ) and depth of been made:
mm and d = 3 mm for normal rough turning. If Cuttingspeed,m/min 40 50
cut (d) are increased individually by 25%,
25% the tool the operation is performed at twice the cutting ToolLife min
ToolLife,min 40 10
life (in min) is speed and the other parameters remain
unchanged, the corresponding percentage change Derive the VT relationship.
((a)) 0.155 ((b)) 1.06 ((c)) 22.50
5 ((d)) 330.0 in tool life is_____________.
is
241 242 243
For-2018 (IES,GATE & PSUs) Page 27 of 213 Rev.0
ToolLifeCurve
l f IES2010Conventional IES2010
y Drawtoollifecurvesforcastalloy,Highspeedsteeland
D llif f ll Hi h d l d The above figure shows a typical
ceramictools. [2 Marks] relationship between tool life and
cutting speed for different
materials. Match the graphs for
Ans.
Ans HSS Carbide
HSS, C bid and d Ceramic
C i tooll
materials and select the correct
answer usingi th code
the d given
i
below the lists:
C d HSS
Code: SS Carbide
C bid C
Ceramici
(a) 1 2 3
(b) 3 2 1
(c) 1 3 2
1.HSS 2.Carbide 3.Ceramic 1.Highspeedsteel 2.castalloyand3.ceramictools. (d) 3 1 2
244 245 246
ForIESOnly
E i f t l tti
Economicsofmetalcutting l
Formula
Vo Ton = C
Optimum tool life for minimum cost
C 1 n
To = Tc + t if Tc , Ct & Cm given
C m n
C 1 n
= t if Ct & Cm ggiven
Cm n
Optimum
p tool life for Maximum Productivity
y
(minimum production time)
1 n
To = Tc
256 257
n 258
g g
Units:Tc min(Toolchangingtime)
IES2009Conventional GATE2014
Determine
D i the
h optimumi cutting
i speed
d for
f an If the Taylors tool life exponent n is 0.2, and the
Ct Rs./servicingorreplacement(Tooling
operation on a Lathe machine using the following
cost) tooll changing
h time is 1.5 min, then
h the
h tooll life
l f (in
(
information:
Cm Rs/min(Machiningcost)
Tool change time: 3 min min) for maximum production rate is .
V m/min(Cuttingspeed)
Tool regrinds time: 3 min
Machine running cost Rs.0.50 per min
Toolingcost(Ct)=toolregrindcost
Depreciation of tool regrinds Rs.
Rs 5.0
50
+tooldepreciationperservice/replacement
The constants in the tool life equation are 60 and
Machiningcost(Cm)=labourcost+overheadcostper
) labourcost+overheadcostper 0.2
min
Answer Answer(Contd.)
( )
Tool change time (Tc ) = 2 min
Tool grinding cost = 5 x (15 + 50)/60 = Rs.
Rs 5.417/edge
5 417/edge
Machining time (Tm ) =
DL
=
150 600
1000 fV 1000 0.25 199.5
= 5.669 min GATE2016
Initial setuptime for a batch (ti ) For a certain job, the cost of metal cutting is Rs.
Tool will be used 10 times (Because first grinding not Total time (Ttotal ) = Idle time (to ) +
needed
d d 9 regrinding
i di needed)
d d) Number of parts produced per batch ( p )
18C/V and
d the
h cost off tooling
l is Rs. 270C/(TV),
( ) where
h
Tooling cost (Ct ) =
60 + 5.417 9
= Rs.10.875 / use of tool Machining time (Tm )
+ Machining time (Tm ) + Tool change time (Tc ) C is a constant,
constant V is cutting speed in m/min and T is
10 Optimum tool life (To )
Machining cost (Cm ) = Labour cost +Overhead cost per min
5.669 the tool life in minutes. The Taylor
Taylorss tool life
=5 + 0 +5 669 + 2
5.669 = 10
10.89min
89min
= (12+40)/60 = Rs. 0.8667/min 51.58
O i
Optimum
C 1 n
life (To ) = Tc + t
tooll lif C t off O
Cost
t T
ti = Cm to + i + Tm + (Ct + Tc Cm ) m
Operation equation is VT0.25 = 150. The cutting speed (in
Cm n p To
5.667
5 667 m/min)) for the minimum total cost is ________
= 2 +
10 875 1 0.22
10.875 0 22
= 51.58min = 0.8667 ( 5 + 0 + 5.667 ) + (10.875 + 2 0.8667 )
0.8667 0.22 51.58
= Rs.10.63 per piece
C 475
Optimum Speed (Vo ) = n = = 199.5m/min
To 51.580.22 265 266 267
C d
Contd. F
From previous
i slide
lid
GATE2005 IAS 2007Contd
A diagram
di related
l t d to
t machininghi i economics
i with ith
various cost components is given above. Match List I
(C t Element)
(Cost El t) with
ith List
Li t II (Appropriate
(A i t Curve)
C ) and d
select the correct answer using the code given below
th Lists:
the Li t
ListI ListII
(CostElement) (AppropriateCurve)
A Machiningcost
A. 1
1. Curvel
B. Toolcost 2. Curve2 Code:A B C D A B C D
C. Toolgrindingcost
l d 3. Curve3 ( ) 3
(a) 2 4 5 ((b)) 4 1 3 2
D. Nonproductivecost
p 4.
4 Curve4
4 (c) 3 1 4 2 (d) 4 2 3 5
268
5. Curve5 269 270
For-2018 (IES,GATE & PSUs) Page 30 of 213 Rev.0
IES2011 MinimumCostVsProductionRate IES 1999
The optimum cutting speed is one which should Consider
C id the
h following
f ll i approaches
h normally
ll
have: applied for the economic analysis of machining:
1. High metal removal rate 1. Maximum production rate
2. High
Hi h cutting
i tooll life
lif 2 Maximum profit criterion
2.
33. Balance the metal removal rate and cutting
g 3. Minimum cost criterion
tool life The correct sequence in ascending order of optimum
(a) 1,
1 2 and 3 cutting speed obtained by these approaches is
(b) 1 and 2 only (a) 1, 2, 3 (b) 1, 3, 2
(c) 2 and 3 only
Vmax.production > Vmax.profit > Vmin. cost (c) 3, 2, 1 (d) 3, 1, 2
(d) 3 onlyl
271 272 273
ForIESOnly
ForIESOnly ForIESOnly
ForIESOnly ForIESOnly
ff
Effects off tooll rake
k angle(s)
l ( ) on IAS 2000 EffectsofCuttingEdgeangle(s)on
machinability Considerthefollowingstatements:
C id h f ll i machinability
Thetoollifeisincreasedbyy
y The
Th variation
i ti ini the
th cutting
tti edge
d angles
l does
d nott affect
ff t
y AsRakeangleincreasesmachinabilityincreases. 1. Builtupedgeformation
cutting force or specific energy requirement for cutting.
cutting
2. Increasingcuttingvelocity
I i i l i
y Buttoomuchincreaseinrakeweakensthecuttingedge.
33. Increasingbackrakeangleuptocertainvalue
g g p y Increase in SCEA and reduction in ECEA improves
Whichofthesestatementsarecorrect? surface finish sizeably in continuous chip formation
( ) 1and3
(a) d (b) 1and2
d
hence Machinability.
(c) 2and3 (d) 1,2and3
ForIESOnly ForIESOnly
301 302
(c) 1 and 2 (d) 3 and 4 303
ForIESOnly
(c) 0.036mm/rev
0 036mm/rev height of surface roughness produced will be tan 8o + cot15o tan15o + cot 8o
(a) (b)
(d) 0.0187mm/rev
0 0187mm/rev tan 8o + cot 30o tan 30o + cot 8o
(a) 0.16 mm (b) 0.26 mm
tan15o + cot7o tan7o + cot15o
(c ) (d )
313 (c) 0.32 mm (d) 0.48 mm 314
tan 30o + cot7o tan7o + cot 30o 315
For-2018 (IES,GATE & PSUs) Page 35 of 213 Rev.0
IES 1993,ISRO2008 IES 2006 GATE2014(PI)
( )
For achieving a specific surface finish in single point In the selection of optimal cutting conditions, the A spindle
i dl speed d off 300 rpm and d a feed
f d off 0.3
mm/revolution are chosen for longitudinal turning
turning the
h most important factor
f to be
b controlled
ll d requirement off surface
f f
finish
h would
ld put a limit
l on operation on an engine lathe. In finishing pass,
is which of the following? roughness
g on the work surface can be reduced byy
(a) reducing the spindle speed
(a) Depth of cut (b) Cutting speed (a) The maximum feed (b) increasing the
h spindle
dl speedd
(c) Feed (d) Tool rake angle (b) The maximum depth of cut (c) reducing
educ g tthee feed
eed o
of too
tool
(d) increasing the feed of tool
(c) The maximum speed
GATE2010(PI)
( ) Cutting fluid
Cuttingfluid
GATE2017 y The cutting fluid acts primarily as a coolant and
During turning of a low carbon steel bar with TiN coated Assume
A that
th t the th surface
f roughness
h profile
fil is
i secondly
dl as a lubricant,
l bi t reducing
d i the th friction
f i ti effects
ff t att
carbide insert, one need to improve surface finish g
triangular as shown schematicallyy in the figure.
g If the toolchip interface and the workblank regions.
without sacrificing material removal rate. To achieve the peak to valley height is 20 m, the central line y Cast Iron: Machined dry or compressed air, Soluble oil
average surface roughness Ra (in m) is for high speed machining and grinding
improved surface finish, one should
y Brass: Machined dry or straight mineral oil with or
(a) decrease nose radius of the cutting tool and increase ((a)) 5 ((b)) 6.677 ((c)) 10 ((d)) 20
without
ih EPA
EPA.
depth of cut y Aluminium: Machined dry y or kerosene oil mixed with
(b) Increase nose radius of the cutting tool mineral oil or soluble oil
(c) Increase feed and decrease nose radius of the cutting y Stainless steel and Heat resistant alloy: High
performance soluble oil or neat oil with high
tool concentration
i with i h chlorinated
hl i d EP additive.
ddi i
(d) Increase depth of cut and increase feed 319 320 321
BySKMondal 1 2 3
Terminology Terminology
Terminology C td
Contd....
Terminology
e o ogy Contd....
y Limits of sizes: There are two extreme permissible Unilateral Limits occurs when both maximum limit and
y No a ssize:
Nominal e: S
Sizee o
of a pa
partt spec ed in tthee d
specified aw g.
drawing.
It is used for general identification purpose. sizes for a dimension of the part. The largest minimum limit are either above or below the basic size.
permissible size for a dimension is called upper or high e.g. 25 +0.18
+0 18
y Basic size: Size of a part to which all limits of variation +0.10
(
(i.e. tolerances)) are applied.
pp Basic dimension is or maximum limit, whereas the smallest size is known
Basic Size = 25.00
25 00 mm
theoretical dimension. as lower or minimum limit. Upper Limit = 25.18 mm
y Tolerance Lower Limit = 25.10 mm
y Actual size: Actual measured dimension of the part. Tolerance = 0.08 mm
The difference between the basic size and the actual The difference between the upper limit and lower
e g 25 -00.10
e.g. 10
size should not exceed a certain limit, otherwise it will limit. -0.20
interfere with the interchangeability of the mating It is the maximum permissible variation in a Basic Size = 25.00 mm
Upper Limit = 24.90 mm
parts. dimension. Lower Limit = 24.80 mm
The tolerance may be unilateral or bilateral. Tolerance = 0.10 mm
4 5 6
Terminology
Terminology Contd
Contd....
Transition Fits
IAS 2015 Main
IAS2015Main Hole
IES 2015
IES2015
A 20 mm diameter shaft and bearing g are to be Consider the following statements
assembled with a clearance fit. The tolerance and Max C
Tolerancezonesalways
allowances are as under : overlap
In case of assemblyy of mating
gpparts
Shaft
Allowance = 0.002 mm Max I 1. The difference between hole size and shaft size is called
Tolerance on hole = 0.005 mm allowance.
T l
Tolerance on shaft
h f = 0.003 mm 2. In transition fit, small positive or negative clearance
Find the limits of size for the hole and shaft, if
b
between the
h shaft
h f and
d hole
h l member
b isi employable
l bl
(i) the hole basis system is used, Max. C = UL of hole - LL of shaft
Max. I = LL of hole - UL of shaft Which of the above statements is/are correct?
(ii) the shaft basis system is used.
The tolerances are disposed off unilaterally.
unilaterally Thetransitionfitsmaybetightfitandpushfit,wringing ((a)) 1 onlyy ((b)) Both 1 and 2
fit(Gear,pulleyonshaft),pressfit.
[10Marks] 22 23 (c) 2 only (d) Neither 1 nor 2 24
Interference Fits
Hole Tolerancezonesnevermeet IES2011 IES2013
butcrosseseachother
Max I Interference fit joints are provided for: Which of the following is a joint formed by
Shaft
i t f
interference fit ?
fits?
Min I (a) Assembling bush bearing in housing
(a) Joint of cycle axle and its bearing
(b) Mounting heavy duty gears on shafts
(b) Joint between I.C.
I C Engine piston and cylinder
(c) Mounting pulley on shafts
(c) Joint between a pulley and shaft transmitting power
(d) Assembly of flywheels on shafts
Max. I = LL of hole - UL of shaft
Min I = UL of hole - LL of shaft
Min. (d) Joint of lathe spindle and its bearing
Theinterferencefitsmaybeshrinkfit,heavydrivefitand
Theinterferencefitsmaybeshrinkfit heavydrivefitand
lightdrivefit. 25 26 27
For-2018 (IES,GATE & PSUs) Page 39 of 213 Rev.0
IES
IES 2014
GATE 2005 StatementI: In interference fit, the outer diameter IES2015
of the inner cylinder will be more than the inner Statement
S (I) : In
I interference
i f fit,
fi the
h outer diameter
di off
In order to have interference fit, it is essential that diameter of the hollow outer cylinder the shaft is greater than the inner diameter of the hole.
the
h lower
l l
limit off the
h shaft
h f should
h ld be
b St t
StatementII:
t II These
Th fit are recommended
fits d d for
f two
t Statement (II) : The amount of clearance obtained from
parts frequently dismantled and assembled. the assemblyy of hole and shaft resulting g in interference fit
( ) Greater
(a) G than
h the
h upper limit
li i off the
h hole
h l (a) Both Statement (I) and Statement (II) are is called positive clearance.
individuallyy true and Statement (II) is the correct (a) Both statement (I) and (II) are individually true and
(b) Lesser
L th the
than th upper limit
li it off the
th hole
h l explanation of Statement (I)
statement (II) is the correct explanation of statement (I)
(c) Greater than the lower limit of the hole (b) Both Statement (I) and Statement (II) are (b) Both
B th statement
t t t (I) and
d statement(II)
t t t(II) are individually
i di id ll
individually true but Statement (II) is not the correct
true but statement(II) is not the correct explanation of
(d) Lesser than the lower limit of the hole explanation of Statement (I)
statement (I)
()
(c) Statement (I) is true but Statement (II) is false
(c) Statement (I) is true but Statement (II) is false
(d) Statement
St t t (I) is
i false
f l but
b t Statement
St t t (II) is
i true
t (d) Statement (I) is false but statement (II) is true
28 29 30
IES2017
Statement (I): In sugarcane crushing rollers, the fit GATE2011 GATE2012SameQinGATE2012(PI)
between the cast roll and the forged steel shaft is of +0.015
i t f
interference t
type. A hole is of dimension 9 +0
mm The
mm. In an interchangeable assembly,
assembly shafts of size 25+0.04
0.01
+0.010
25++0.03
Statement (II): This helps in removing the roll from the
corresponding shaft is of dimension 9 +0.001
mm. mm mate with holes of size 0 03
0.02
mm.
shaft whenever not needed. The resultingg assemblyy has
(a) Both statement (I) and (II) are individually true and (a) loose running fit The maximum interference (in microns) in the assembly
statement (II) is the correct explanation of statement (I)
(b) close
l running
i fit
fi is
(b) Both statement (I) and statement(II) are individually
true but statement(II) is not the correct explanation of (c) transition
a s o fit (a) 4
40 ((b)) 330 (c) 20 (d) 10
statement (I) (d) interference fit
(c) Statement (I) is true but Statement (II) is false
(d) Statement (I) is false but statement (II) is true 31 32 33
(c)Clearancefit
(d)Noneoftheabove
Hint: Use unilateral hole basis system.
34 35 36
For-2018 (IES,GATE & PSUs) Page 40 of 213 Rev.0
IES 2006 IES 2009 IES 2008
Which of the following is an interference fit? Consider
C id the
h following
f ll i joints:
j i Consider
C id the h following
f ll i statements:
1. Railwayy carriageg wheel and axle g
1. The amount of interference needed to create a tight
(a) Push fit 2. IC engine cylinder and liner joint varies with diameter of the shaft.
(b) Running fit Whi h off the
Which h above
b j i
joints i /
is/are the
h result(s)
l ( ) off 2 An interference fit creates no stress state in the
2.
interference fit? shaft.
( ) Sliding fit
(c) (a) 1 only 3. The stress state in the hub is similar to a thick
(b) 2 only
l walled
a ed cy
cylinder
de witht internal
te a p pressure.
essu e.
(d) Shrink
Sh i k fit
fi
(c) Neither 1 nor 2 Which of the statements given above are correct?
(d) Both 1 and 2 ( ) 1, 2 and
(a) d3 (b) 1 and d 2 only
l
(c) 2 and 3 only (d) 1 and 3 only
37 38 39
IES 2015
IES2015 IES 2004 Allowance
y It is Minimum clearance or maximum interference. It is
In
I an interference
i f fit
fi between
b a shaft
h f and
d a hub,
h b the
h state Consider
C id theh following
f ll i fits:
fi the intentional difference between the basic
of stress in the shaft due to interference fit is 1. I.C. engine
g cylinder
y and p
piston dimensions of the mating
gpparts. The allowance mayy be
2. Ball bearing outer race and housing positive or negative.
a)) onlyy compressive
p radial stress
3. Ball
B ll bearing
b i inner
i race and
d shaft
h f
b)a tensile radial stress and a compressive tangential stress Which of the above fits are based on the interference
c) a tensile tangential stress and a compressive radial stress system?
( ) 1 and
(a) d2
d)a compressive tangential stress and a compressive radial
(b) 2 and 3
stress (c) 1 and 3
(d) 1, 2 and
d3
40 41 42
(a) Maximum clearance between shaft and hole (a) Allowance is equal to bilateral tolerance (a) Maximum hole size and minimum shaft size
(b) Minimum clearance between shaft and hole (b) Allowance is equal to unilateral tolerance (b) Minimum hole size and maximum shaft size
ISRO2010
y For hole basis system,
y , H stands for dimensions of holes
ZeroLine
+0.02 whose lower deviation is zero.
Dimension of the hole is 50 mm
0.00
y The basic size of the hole is taken as the lower limit of
+0.02
0 02
and shaft is 50 mm. size of the hole ( Maximum metal condition).
+0.00
0.00
The minimum clearance is Hole basis system y The higher limit of size of the hole and two limits of size
(a) 0.02 mm (b) 0.00 mm y The hole is kept as a constant member (i.e. when the for the shaft are then selected to give desired fits.
lower deviation of the hole is zero))
(c) -0.02
0 02 mm (d) 0.01
0 01 mm y The actual size of hole is always more than basic size or
y Different fits are obtained by varying the shaft size then
the limit system is said to be on a hole basis.
basis equal to basic size
si e but never
ne er less than Basic size.
si e
46 47 48
ForIESOnly
ShaftBasissystem
Why Hole Basis Systems are Preferred?
WhyHoleBasisSystemsarePreferred?
y For shaft basis system,
y , h stands for dimensions of shafts y Holes can be finished by
y tools like reamers,, drills,,
ZeroLine whose upper deviation is zero. broaches, and their sizes are not adjustable. The shaft
y Basic size of the shaft is taken Upper limit for the shaft ( sizes can be easily obtained by external machining.
selected to give the desired fit. different classes of holes for one class of shaft for
Shaft basis system:
y When the shaft is kept as a constant member (i.e.
(i e when the obtaining different fits which increases cost of
upper deviation of the shaft is zero) y Actual size of shaft is always less than basic size or equal
production.
y Different fits are obtained by varying the hole size then the to basic size
si e but never
ne er more than basic size.
si e
limit system is said to be on a shaft basis. 49 50 y It is economical 51
m
ToleranceZone y Limits and fits comprises 18 grades of fundamental ToleranceDesignation(IS)
tolerances for both shaft and hole, designated as IT01, Tolerance on a shaft or a hole can be calculated by using
It is defined graphically IT0 and IT1 to IT16. These are called standard table provided.
provided
55 tolerances. (IS919) But ISO 286 specify 20 grades upto
by the magnitude of the T = K i
Tolerance Zone tolerance and by its IT18
20 position in relation to the y There are 25 (IS 919) and 28 (ISO 286) types of Where, T isthetolerance(inm)
zero line. fundamental deviations.
deviations Standard Tolerance unit or Fundamental tolerance unit
Hole: A, B, C, CD, D, E, EF, F, FG, G, H, J, JS, K, M, N, P,
i = 0.45 3 D + 0.001D in m
Basic Size R S,
R, S T,
T U,U V,
V X,
X Y,Y Z,
Z ZA,
ZA ZB,
ZB ZC.ZC
Shaft : a, b, c, cd, d, e, ef, f, fg, g, h, j, js, k, m, n, p, r, s, t, D = D1D2 (D1 and D2 are the nominal sizes marking
u, v, x, y, z, za, zb, zc. the beginning and the end of a range of
y A unilateral hole basis systemy is recommended but if sizes,, in mm))
necessary a unilateral or bilateral shaft basis system may K = is a constant [ForIT6toIT16]
55 56
also be used
ValueoftheTolerance
Diameter Steps
DiameterSteps IT01 IT0 IT1 IT2
Above Upto andincluding 0.3 + 0.008D 0.5 + 0.012D 0.8 + 0.02D ar GradesofTolerance
(mm)
( ) (mm)
( ) =a r = 101/5 y It is an indication of the level of accuracy.
3 IT3
3 IT4 IT5
5 IT6
6
3 6 ar2 ar3 ar4 = 7i 10(1.6)(ITn -IT6) y IT01 to IT4 For production of gauges, plug gauges,
6
6 10 = 10i
measuring
i instruments
i
10 18 IT7 IT8 IT9 IT10
188 30 10(1.6)
( )(ITn -IT6) 10(1.6)
0( 6)(ITn -IT6) 10(1 6)((ITn -IT6))
10(1.6) 10(1 6)(ITn -IT6)
10(1.6) IT6)
y IT5
IT to
t IT 7 For
F fits
fit in
i precision
i i engineering
i i applications
li ti
30 50 = 16i = 25i = 40i = 64i
550 80
IT11 IT12 IT13 IT14 y IT8 to IT11 For General Engineering
80 120
10(1.6)(ITn -IT6) 10(1.6)(ITn -IT6) 10(1.6)(ITn -IT6) 10(1.6)(ITn -IT6)
120 180
180 250 = 100i = 160i = 250i = 400i
y IT12 to IT14 For Sheet metal working or press working
250 315 IT15 IT16 y IT15 to IT16 For processes like casting,
casting general cutting
315 400 10(1.6)(ITn -IT6) 10(1.6)(ITn -IT6)
400 500 58
= 640i = 1000i 59
work 60
Fundamental Deviation
is chosen to locate the tolerance zone w.r.t. the zero line Shaft Fundamental Deviation
CalculationforUpperandLowerDeviation
a (265 + 1.3D ) for D 120 mm
y ForShaft
Holes are designated by capital letter: 3.5D for D > 120 mm
Letters A to G - oversized holes ei =es IT
Letters P to ZC - undersized holes b (140 + 0.85
0 85D ) for D 160 mm
es =ei +IT 1.8 D for D > 160 mm
y ForHole
F H l c 52D 0.2 for D 40 mm
EI=ES IT
(95 + 0.8
0 8D ) f D > 40 mm
for
Shafts are designated by small letter: ES=EI+IT
Letters m to zc - oversized shafts d 16 D 0.44
Letters a to g - undersized shafts
e 11D 0.41
H is used for holes and h is used for shafts es =upperdeviationofshaft
pp
whose fundamental deviation is zero
ei =lowerdeviationofshaft f 5.5D 0.41
ES=upperdeviationofhole g 2 5D 0.41
2.5
61 EI=lowerdeviationofhole 62 h 0 63
For-2018 (IES,GATE & PSUs) Page 43 of 213 Rev.0
Shaft Fundamental Deviation
j5 to j8
k4 to
t k7 + 0.6
0 63 D
m + ( IT 7 IT 6) y For hole, H stands for a dimension whose lower
n + 5D 0.34
0 34
deviation
d i ti refers
f t the
to th basic
b i size.
i TheTh hole
h l H for
f which
hi h
p + IT 7 + (0 5) the lower deviation is zero is called a basic hole.
r Geometric mean of values of
y Similarly, for shafts, h stands for a dimension whose Basicsize HoleToleranceZone
ei for p and s
upper deviation refers to the basic size. The shaft h for
s IT 8 + 1 to 4 for D 50 mm ShaftToleranceZone
IT 7 + 0.4 D for D > 50 mm
which the upper deviation is zero is called a basic
t IT 7 + 0.63
0 63D
shaft.
u IT 7 + D y A fit is designated by its basic size followed by symbols
v IT 7 + 1.25D representing the limits of each of its two components,
F d
FundamentalDeviation
t lD i ti IT#
x IT 7 + 1.6 D the hole being quoted first.
y IT 7 + 2D y For example,
example 100 H6/g5 means basic size is 100 mm
z IT 7 + 2.5D
and the tolerance grade for the hole is 6 and for the
za IT 8 + 3.15D
shaft is 5.
5
zb IT 9 + 4 D
zc IT 10 + 5D 64 65 66
GATE 2014
GATE2014 IES 2008 IES2006Conventional
g y 5 g p
Forthegivenassembly:25H7/g8,matchGroupAwith
GroupB Consider
C id theh following
f ll i statements: Find
Fi d the
h limit
li i sizes,
i tolerances
l and
d allowances
ll for
f a
GroupA
p GroupB
p A nomenclature 550 H8/p8 /p denotes that 100 mm diameter shaft and hole pair designated by
1. Hole diameter is 50 mm. F8h10. Also specify the type of fit that the above pair
P.H I.ShaftType belongsg to.
2. ItI is
i a shaft
h f base
b system.
Q.IT8 II.HoleType Given: 100 mm diameter lies in the diameter step
33. 8 indicates fundamental deviation. range of 80120
80 120 mm.
mm The fundamental deviation for
R.IT7 III.HoleToleranceGrade Which of the statements given above is/are incorrect? shaft designation f is 5.5 D0.41
S
S.g IV Sh ftT l
IV.ShaftToleranceGrade
G d ( ) 1, 2 and
(a) d3 The values of standard tolerances for grades of IT 8
P Q R S P Q R S (b) 1 and 2 only and IT 10 are 25i and 64i respectively.
(a) I III IV II (b) I IV III II (c) 1 and 3 only Also, indicate the limits and tolerance on a diagram.
( ) 3 only
(d) [ M k ]
[15Marks]
(c) II III IV I (d) II IV III I
67 68 69
79 80 81
For-2018 (IES,GATE & PSUs) Page 45 of 213 Rev.0
ForIESOnly ForIESOnly
Interchangeability
SelectiveAssembly y Interchangeability,
g y a maintainabilityy design
g factor, is
quite closely related to standardization and is realized
ISRO2008
y All the parts (hole & shaft) produced are measured
through standardization. I t h
Interchangeability
bilit can be
b achieved
hi d by
b
and graded into a range of dimensions within the
y If the variation of items are within certain limits, all
tolerance groups. (a) Standardization
parts of equivalent size will be equally fit for operating in
machines and mechanisms and the mating parts will (b) Better process planning
y Reduces
d the
h cost off production
d
give the required fitting.
(c) Simplification
Process capability y This facilitates to select at random from a large number
y No.of group =
Tolerance desired of parts for an assembly and results in a considerable (d) Better product planning
saving in the cost of production, reduce assembly time,
replacement and repair becomes very easy.
easy
82 83 84
GATE 2015
GATE-2015 GATE 2007(PI)
GATE2007(PI) GATE 2007(PI)
( )
Intheassemblyshownbelow,thepartdimensionsare:
The geometric tolerance that does NOT need a datum
0.01
L 1 = 22.0 mm for its specification is Diameter of a hole after plating needs to be controlled
0.005 between 30++0.050
0.010 mm. If the plating thickness varies
L2 = L3 = 10.0
10 0 mm ((a)) Concentricityy ((b)) Runout
between 10 - 15 microns, diameter of the hole before
Assumingnormaldistributionofpartdimensions
Assumingnormaldistributionofpartdimensions, ((c)) Perpendicularity
p y ((d)) Flatness
plating
l i should
h ld be
b
thedimensionL4 inmm,
(a) 30++0.070
0.030 mm (b) 30++0.065
0.020 mm
a)2.000.008 b)2.000.012
c)2.00
) 0 016
0.016
d)2.000.020
d) 0 020 (c) 30++0.080
0.030 mm (d) 30++0.070
0.040 mm
88 89 90
For-2018 (IES,GATE & PSUs) Page 46 of 213 Rev.0
GATE2013 GATE 2017 GATE 2000
A cylindrical
li d i l pin
i off mm diameter
di is
i A slot
l isi to be
b milled
ill d centrally
ll on a block
bl k with
ih a
Cylindrical pins of 25++0.020
0.010 mm diameter are p
electroplated. Plating
g thickness is mm. dimension of 40 0.05 mm. A milling cutter of 20
mm width is located with reference to the side of
electroplated in a shop. Thickness of the Neglecting the gauge tolerance, the diameter (in mm, up
to 3 decimal points accuracy) of the GO ring gauge to the block within 0.02 mm. The maximum offset in
plating is 30 2.0 micron. Neglecting gage inspect the plated pin is_________ mm between the centre lines of the slot and the
block is
tolerances, the size of the GO gage in mm (a) 0.070 (b) 0.070
tto iinspectt the
th plated
l t d components
t iis (c) 0.020 (d) 0.045
(a) 2525.042
042 (b) 25.052
25 052 (c) 25
25.074
074 (d) 25.084
25 084
91 92 93
94 Fig.Pluggauge Fig.Ringandsnapgauges 95 96
ForIESOnly
GATE 2006,VS2012 T l Pi i l
TaylorsPrinciple LimitGauges
A ringi gauge is i used d to measure This principle states that the GO gauge should always be Gauge ForMeasuring
((a)) Outside diameter but not roundness SnapGauge ExternalDimensions
so designed
d d that
h it will
ll cover the
h maximum metall
(b) Roundness but not outside diameter
PlugGauge
g g InternalDimensions
( ) Both
(c) B h outside
id diameter
di and
d roundness
d condition (MMC) of as many dimensions as possible in
TaperPlugGauge Taperhole
((d)) Onlyy external threads the same limit gauges, whereas a NOT GO gauges to
RingGauge ExternalDiameter
cover the minimum metal condition of one dimension
G G
GapGauge G dG
GapsandGrooves
only.
RadiusGauge Gaugingradius
ThreadpitchGauge
p g ExternalThread
106 107 108
For-2018 (IES,GATE & PSUs) Page 48 of 213 Rev.0
FeelerGauge GATE2016
PSU Matchthefollowing:
Af l
Afeelergaugeisusedtocheckthe
i dt h kth P.Feelergauge
P Feelergauge II.Radiusofanobject
Radiusofanobject
Q.Filletgauge II.Diameterwithinlimitsby
(a)Pitchofthescrew comparison
(b)Surfaceroughness R.Snapgauge III.Clearance orgapbetween
components
(c)Thicknessofclearance S.Cylindricalplug
S C li d i l l IV I id di
IV.Insidediameterof
t f straight
t i ht
(d)Flatnessofasurface gauge hole
(a)PIII,QI,RII,SIV (b)PIII,QII,RI,SIV
109 110
(c)PIV,QII,RI,SIII (d)PIV,QI,RII,SIII 111
ForIESOnly ForIESOnly
Whyisaunilateraltolerance
Why is a unilateral tolerance Preferred Number
PreferredNumber Preferred Number Contd.
PreferredNumber.. C td
y A designed product needs standardization. y These are named as Renard series.
preferredoverbilateraltolerance?
preferred over bilateral tolerance ? y Motor speed, engine power, machine tool speed and y Many other derived series are formed by multiplying or
y This system is preferred for Interchangeable manufacturing.
manufacturing feed, all follows a definite pattern or series. dividing the basic series by 10, 100 etc.
y This also helps in interchangeability of products. y Typical values of the common ratio for four basic G.P.
y It is easy and simple to determine deviations.
deviations series
i are given
i b l
below.
y It has been observed that if the sizes are put in the form
y It helps
p standardize the GO g
gauge
g end of ggeometric p progression,
g
with a definite sequence.
, then wide ranges
g are covered R5 : 11.58
58 :1
:1.0,1.6,
0 1 6 2.5,...
25 ( 10
5
10, 100 5
1000 ) 5
100, 1000,....
:1 0 1 25 1 6 ( 10, 1000 )
y Helpful for operator because he has to machine the upper 10 10 10
y These numbers are called preferred numbers having R10 : 1.26
1 26 :1.0,1.25,1.6,... 10 100,
100 1000,....
limit of the shaft and the lower limit of the hole knowing common ratios as,
fully well that still some margin is left for machining before 5
10 1.58, 10
10 1.26, 20
10 1.12 and 40 10 1.06 R 20 : 1.12 :1 0 1 12 1 4 ( 10
1 12 :1.0,1.12,1.4,... 20 20
10, 100, 1000,....)
100 1000 20
112
formed; these are R5 , R10 , R20 and R40 113 114
(a) Zero error having 25 divisions on vernier scale, matching in common use.
127 128
StepIII: Add the value in StepI and StepII 129
SlipGaugesorGaugeblocks y Come in sets with different number of pieces in a given To make up a Slip Gauge pile to 41.125 mm
y These
Th are small
ll blocks
bl k off alloy
ll steel.
l sett to
t suit it the
th requirements
i t off measurements. t y A Slip
Sli Gauge
G pile
il is
i sett up with
ith the
th use off simple
i l
y Used in the manufacturing
g shops
p as length
g standards. y A typical
yp set consisting
g of 88 p
pieces for metric units is maths.
y Not to be used for regular and continuous shown in.
y Decide what height
g y you want to set up,
p in this
measurement.
measurement y To
T build
b ild any giveni di
dimension,
i it is
i necessary to t
y Rectangular blocks with thickness representing the identifyy a set of blocks,, which are to be p put together.
g case 41.125mm.
dimension of the block. The crosssection of the block y Number of blocks used should always be the smallest. y Take away the thickness of the two wear gauges,
iss usua
usuallyy 332 mm x 9 mm..
y Generally
G ll theh top and d bottom
b Sli Gauges
Slip G i the
in h pile
il and then use the gauges in the set to remove
y Are hardened and finished to size. The measuring
are 2 mm wear g gauges.
g This is so that theyy will be the
surfaces
f off the
th gauge blocks
bl k are finished
fi i h d to
t a very high
hi h each place of decimal in turn,
turn starting with the
degree of finish, flatness and accuracy. only ones that will wear down, and it is much cheaper
lowest.
to replace
l two gauges than
h a whole
h l set.
139 140 141
GATE 2007(PI)
( ) Mechanical Comparators
MechanicalComparators
y The Mikrokator principle
Which one of the following instruments is a
greatly magnifies any
comparator
t ? d i ti
deviation i size
in i so that
th t
even small deviations
(a) Tool Maker
Makerss Microscope produce
d l
large d fl
deflections off
the p
pointer over the scale.
(b) GO/NO GO gauge
SigmaMechanicalComparator
MechanicalComparators
Mechanical Comparators
The Sigma Mechanical Comparator uses a partially
y The EdenRolt Reed system
y uses a
wrapped
d band
b d wrapped
d about
b a driving
d d
drum to turn a
pointer attached to the end of two
pointer needle.
needle The assembly provides a frictionless
reeds. One reed is pushed by a
movement with a resistant pressure provided by the
plunger, while the other is fixed. As
springs.
one reed
d moves relative
l ti tot the
th other,
th
the pointer that they are commonly
attached to will deflect.
SigmaMechanicalComparator
151 152 153
For-2018 (IES,GATE & PSUs) Page 53 of 213 Rev.0
OpticalComparators PneumaticComparators
y These
Th devices
d i use a plunger
l to rotate a mirror.
i A light
li h y Flow type:
beam is reflected off that mirror, and simply by the Inthissystem,Mechanicalamplification
virtue of distance, the small rotation of the mirror can =20/1, y The float height is essentially proportional to the air
be converted to a significant
g translation with little
A d O i l
And,Opticalamplification
lifi i that
h escapes from
f the
h gauge head
h d
friction.
50/1x2
y Master
M t gauges are used
d to
t find
fi d calibration
lib ti points
i t on
Itismultipliedby2,becauseifmirror
istiltedbyanangle thenimage
istiltedbyanangle,thenimage the scales
willbetiltedby2x.Thusoverall
y The input pressure is regulated to allow
magnificationofthissystem
=2x(20/1)(50/1=2000units)
2x(20/1)(50/1 2000units) magnification adjustment
154 155 156
Sine Bar
SineBar
y When a reference for a nonsquare angle is required, a sine bar
can be used.
y Basically a sine bar is a bar of known length.
length When gauge blocks
are placed under one end, the sine bar will tilt to a specific
angle.
y Knowing the height differential of the two rollers in alignment
with the workpiece ,the angle can be calculated using the sine
formula.
y A sine bar is specified by the distance between the centre of the
two rollers, i.e. 100 mm, 200 mm, & 300 mm. the various part of
sine bar are hardened before grinding & lapping. H
ABevelProtractor s in =
160 161
L 162
For-2018 (IES,GATE & PSUs) Page 54 of 213 Rev.0
( )
GATE2012(PI) Disadvantages
ISRO2011 y 1. Sine bars cannot be used for conveniently for
A sine bar has a length of 250 mm. Each roller has
A sine
i bar
b is
i specified
ifi d by
b measuring angles h 60o because
l more than b off slip
l gauge
a diameter of 20 mm. During taper angle
(a) Its total length adjustment problems.
problems
measurement of a component, the height from the
(b) The size of the rollers surface
f plate
l to the
h centre off a roller
ll isi 100 mm. y 2.
2 Misalignment of workpiece with sine bar may
(c) The centre distance between the two rollers sometimes introduce considerable errors.
Th calculated
The l l t d taper
t angle
l (in
(i degrees)
d ) is
i
(d) The distance between rollers and upper surface ( ) 21.1
(a) (b) 22.8
8 ( ) 23.6
(c) 6 (d) 68.9
68
The Three-Wire Method of Measuring Threads y Distance W over the outer edge
p
W = D p + d 1 + cosec cot
2 2 2
For ISO metric thread,, = 60 and D p = D 0.6496 p
W = D + 3d 1.5156 p
y Best wire size
p
d= sec
2 2
For ISO metric thread, = 60
D p = pitch diameter or Effective diameter
d = 0.5774 p
169 p = pitch of thread , and = thread angle 170 171
For-2018 (IES,GATE & PSUs) Page 55 of 213 Rev.0
y Pitch
Pit h Diameter
Di t or Eff
Effective
ti Di
Dia.
Two-Wire Method Dp = T + P
p
GATE
GATE 2011(PI)
2011 (PI)
y Two wires of equal diameter placed in thread, two on =T + cot d cosec 1
2 2 2 The best wire size (in mm) for measuring
one side and one on other side T = Dimensions under the wire = D + ( Dm Ds ) effective diameter of a metric thread
D=D Diameter
i t off master
t or standard
t d d cylinder
li d (included angle is 60o) of 20 mm diameter and
Dm = Micrometer reading over standard cylinder with two wire 2.5 mm pitch using two wire method is
D s = Micrometer reading over the plug screw gauge with the wire (a) 1.443
P = Pitch value (b) 0.723
0 723
y Best wire size (c) 2.886
p (d) 2.086
d= sec
2 2
172 173 174
GATE2013 IES2017(Pre)
( )
A metric thread of pitch 2 mm and thread A metric thread of pitch 2 mm and thread
GATE
GATE 2011(PI)
2011 (PI)
To measure the effective diameter of an external
angle 60 inspected for its pitch diameter angle 60o is inspected for its pitch diameter metric thread (included angle is 60o) of 3.5 mm
pitch,, a cylindrical
p y standard of 330.55 mm diameter
using 3wire method. The diameter of the using the 3wire method. The indicated and two wires of 2 mm diameter each are used.
The micrometer readings over the standard and
best size wire in mm is diameter of the wire will be nearly over the wires are 16.532 mm and 15.398 mm,
respectively. The effective diameter (in mm) of the
(a) 0.866 (b) 1.000 (c) 1.154 (d) 2.000 (a)0.85mm (b)1.05mm thread is
(a) 33.366
33 366 (b) 30.397
30 397
(c)1.15mm (d)2.05mm (c) 29.366 (d) 26.397
Surfaces y Surfacegeometrycanbequantifiedafewdifferent
ways.
ways
y No surface is perfectly smooth, but the better the
surface
f quality,
l the
h longer
l a product
d generally
ll lasts,
l
and the better is performs.
performs
MeasurementofSurfaces
fS f y Surface texture can be difficult to analyse
q
quantitatively.
y y Realsurfacesarerarelysoflat,orsmooth,butmost
Realsurfacesarerarelysoflat orsmooth butmost
commonlyacombinationofthetwo.
y Two surfaces may
y be entirelyy different, yyet still p
provide
the same CLA (Ra) value.
Lay LayContd..
y Waviness: refers to those surface irregularities that have Diagram Symbol Description Diagram Symbol Description
a greater spacing than that of roughness width.
width Parallel lay: Lay parallel to Multidirectional lay: Lay
y Determined by the height of the waviness and its the Surface. Surface is multidirectional. Surface is
width. produced
d d b
by shaping,
h i produced
d d by b grinding,
i di
y The greater the width,
width the smoother is the surface and planning etc. lapping, super finishing.
thus is more desirable. Perpendicular lay: Lay Circular lay:
y Lay
L di
direction:
i i the
is h direction
di i off the
h predominant
d i perpendicular to the Approximately circular
surface pattern produced on the workpiece by the tool Surface. Surface is produced relative to the center.
marks. b shaping
by h i and d planning
l i S f
Surface i produced
is d d by b
Crossedlay:Layangularin
y y g facing.
y Flaw: are surface irregularities that are present which are
random and therefore will not be considered. bothdirections. Radiallay:Approximately
Surface is produced by radialrelativetothecenter
184
knurling, honing. 185
ofthenominalsurface. 186
(a)Metalhardness
( ) Screw
(a) S threads
h d (b) Fl
Flatness
( ) Angularity
(c) A l it (d) S f
Surface fi i h
finish
(b)Sharpnessoftooledge
(c)Surfacedimensions
(d)Surfaceroughness
(a) Primary texture (b) Secondary texture (a) Roughness (b) Lay
A B C D A B C D
(a) 4 2 1 3 (b) 3 2 1 4
202 203 (c) 4 1 2 3 (d) 3 1 2 4204
Profilometer Contactprofilometers
y Adiamondstylusismovedverticallyincontactwitha
Adi d l i d i ll i i h
y Measuring instrument used to measure a surface's sampleandthenmovedlaterallyacrossthesamplefor
profile, in order to quantify its roughness. aspecifieddistanceandspecifiedcontactforce.
y Aprofilometercanmeasuresmallsurfacevariationsin
y Vertical resolution is usually in the nanometre level, verticalstylusdisplacementasafunctionofposition.
though
h h lateral
l l resolution
l is usually
ll poorer. y Theradiusofdiamondstylusrangesfrom20
h d fd d l f
nanometresto25m.
ForIESOnly
GATE 2016
GATE2016
y When the fringes are perfectly straight and same fringe Two optically flat plates of glass are kept at a small
width for dark and bright band we conclude that the anglel as shown
h in
i the
th figure.
fi Monochromatic
M h ti light
li ht
is incident vertically.
surface is perfectly flat.
flat
y For convex surface the fringes curve around the point of
contact.
y For concave surface the fringes curve away from the point
of contact.
The distance of air gap between two successive fringes is given by =
2
n If the wavelength of light used to get a fringe
Distance of air ggap g of n order is =
p of interference fringe th
ForIESOnly
Cli t
Clinometer Clinometer A t lli t
Autocollimator
y An opt ca instrument
optical st u e t for
o noncontact
o co tact measurement
easu e e t o
of
y An
A optical
i l device
d i for
f measuring
i elevation
l i angles
l above
b
small angles or small angular tilts of a reflecting surface.
horizontal.
y Used
U d to t align
li components t and d measure deflections
d fl ti i
in
y Compass clinometers are fundamentally just magnetic
optical or mechanical systems.
compasses held with their plane vertical so that a
plummet or its equivalent can point to the elevation of y An autocollimator works by projecting an image onto a
the sight line.
line target mirror, and measuring the deflection of the
returned image against a scale, either visually or by
y The clinometer can read easily and accurately angles of
means of an electronic detector.
detector
elevation that would be very difficult to measure in any
other simple and inexpensive way. y A visual autocollimator can measure angles as small as
0.5 arcsecond, while an electronic autocollimator can be
y A fairly common use of a clinometer is to measure the
up
p to 100 times more accurate.
h i ht off trees.
height t
232 233 234
For-2018 (IES,GATE & PSUs) Page 62 of 213 Rev.0
y Visual autocollimators are used for lining up laser rod Autocollimator GATE 1998
ends
d andd checking
h ki the
th face
f parallelism
ll li off optical
ti l Auto
A collimator
lli is
i used
d to check
h k
windows and wedges. ((a)) Roughness
g
y Electronic and digital autocollimators are used as (b) Flatness
angle
l measurementt standards,
t d d for f monitoring
it i angular l ( ) Angle
(c) A l
movement over long periods of time and for checking ((d)) Automobile balance.
angular position repeatability in mechanical systems.
y Servo
S autocollimators
t lli t are specialized
i li d compactt forms
f off
electronic autocollimators that are used in high speed
servo feedback loops for stable platform applications.
OpticalSquare
GATE
GATE 2009(PI)
2009 (PI) GATE
GATE 2014 y An
A Optical
O ti l square consists
i t off a small
ll cylindrical
li d i l metal
t l box,
b
about 5 cm in diameter and 12.5 cm deep, in which two
A autocollimator
An t lli t is i used
d to
t Th flatness
The fl t off a machine
hi b d can be
bed b mirrors are placed at an angle of 45o to each other and at
right angles to the plane of the instrument.
(a) measure small angular displacements on flat measured using y One mirror(horizon glass) is half silvered and other(index
glass) is wholly silvered.
surface (a) Vernier calipers y Th optical
The ti l square belongs
b l t a reflecting
to fl ti instruments
i t t which
hi h
measure angles by reflection. Angle between the first
((b)) compare
p known and unknown dimensions ((b)) Auto collimator incident ray and the last reflected ray is 90o
((c)) measure the flatness error ((c)) Height
g g gauge
g y Used to find out the foot of the perpendicular from a given
point
i t to
t a line.
li
(d) measure roundness error between centers (d) Tool makers microscope y Used to set out right angles at a given point on a line in the
fi ld
field.
238 239 y Two mirrors may be replaced by two prisms. 240
ISRO2010 LaserScanningMicrometer
Optical
O i l square is i y The LSM features a high scanning rate which allows
((a)) Engineer's
g square
q having 90o
g stock and blade set at 9 inspection
p of small workpiece
p even if theyy are fragile,
g ,
(b) A constant deviation prism having the angle of at a high temperature, in motion or vibrating.
deviation between the incident ray and reflected ray, ray y Applications :
equal to 90o y Measurement of outer dia. And roundness of
(c) A constant deviation prism having the angle of cylinder,
deviation
dev at o bet
between
ee tthee incident
c de t ray
ay aand
d reflected
e ected ray,
ay, y Measurement of thickness of film and sheets,
sheets
equal to 45o y Measurement of spacing if IC chips,
(d) Used
U d tot produce
d i t f
interference fi
fringes y Measurement of forms,
y Measurement of gap between rollers.
rollers
AnOpticalSquare 241 242 243
For-2018 (IES,GATE & PSUs) Page 63 of 213 Rev.0
IES 1998 Laser interferometer
Laserinterferometer
Match ListI
List I with ListII
List II and select the correct answer using the y Laser interferometers represent the ultimate feedback
codes given below the lists: device for highprecision motion control application.
ListI ListII
(Measuring Device) (Parameter Measured) y The
h combination
b off high
h h resolution
l and
d outstanding
d
A. Diffraction grating 1. Small angular deviations on long accuracyy has made it the ideal transducer for wafer
flat surfaces
B. Optical flat 2. Online measurement of moving steppers, flat panel inspection, and highaccuracy laser
p
parts micromachining.
C. Auto collimators 3. Measurement of gear pitch
D. Laser scan micrometer4. Surface texture using interferometer y A laser interferometer system employs a highly stabilized
5. Measurement off very smallll li ht source and
light d precision
i i optics
ti to
t accurately
t l measure
displacements
distances.
Code: A B C D A B C D
(a) 5 4 2 1 (b) 3 5 1 2 y An additional advantage is that interferometers measure
((c)) 3 5 4 1 ((d)) 5 4 1 2 distances directly at the workpiece.
244 245 246
GATE2014 McLeodgauge
y Used
d to measure vacuum by
b application
l off the
h
Which one of the following instruments is widely
principle of Boyle's law.
used to check and calibrate geometric features of
y Works on the principle, "Compression of known
machine tools during their assembly?
volume of low p pressure ggas to higher
g pressure and
p
(a) Ultrasonic probe measuring resulting volume & pressure, one can
calculate initial p
pressure usingg Boyle's
y Law equation."
q
(b) Coordinate Measuring Machine (CMM) y Pressure of gases containing vapours cannot normally
measured with a McLeod gauge, gauge for the reason that
( ) Laser interferometer
(c) f
compression will cause condensation .
(d) Vernier calipers y A pressure from
f 0.01 micron
i t 50 mm Hg
to H can beb
measured. Generally McLeod gauge is used for
calibration
lib ti purpose.
247 248 249
Planimeter LVDT
y Adeviceusedformeasuringtheareaofanyplane y Acronym for Linear Variable Differential Transformer,
surfacebytracingtheboundaryofthearea.
y g y a common type yp of electromechanical transducer that
can convert the rectilinear motion of an object to
which it is coupled mechanically into a corresponding
electrical signal.
y LVDT linear
li position
i i sensors are readily
dil available
il bl that
h
can measure movements as small as a few millionths of
an inch up to several inches, but are also capable of
measuring
easu g pos positions
o s up to
o 20 inches
c es ((0.5
.5 m).
).
y A rotary variable differential transformer (RVDT)
i a type
is t off electrical
l t i l transformer
t f used d for
f measuring i
250 251 angular displacement. 252
For-2018 (IES,GATE & PSUs) Page 64 of 213 Rev.0
LVDT GATE 1992 ToolMakersMicroscope
Match
M t h the
th instruments
i t t with
ith the
th physical
h i l quantities
titi they
th An essential part of engineering inspection,
measure:
measurement and calibration in metrology gy labs.
I
Instrument M
Measurement
Hence is used to the following:
(A) Pilottube (1) R.P.M. of a shaft
y Examination of form tools,tools plate and template
(B) McLeod Gauge (2) Displacement
((C)) Planimeter (3) Flow velocityy
gauges, punches and dies, annular grooved and
(D) LVDT (4) Vacuum
threaded
h d d hobs
h b etc.
(5) Surface finish y Measurement of g glass ggraticules and other surface
(6) Area marked parts.
C d A
Codes:A B C D A B C D y Elements
El t off external
t l thread
th d forms
f off screw plug
l
(a) 4 1 2 3 (b) 3 4 6 2 gauges, taps, worms and similar components.
(c) 4 2 1 3 (d) 3 1 2 4 y Shallow bores and recesses.
253 254 255
GATE 1995 C di t M i M hi
CoordinateMeasuringMachine
g ,
Advantages,
List
Li I List
Li II (CMM)
y canautomateinspectionprocess
((Measuring g instruments)) ((Application)
pp ) y Aninstrumentthatlocatespointcoordinatesonthree
st u e t t at ocates po t coo d ates o t ee
y lesspronetocarelesserrors
l l
(A) Talysurf 1. Tslots dimensionalstructuresmainlyusedforqualitycontrol
applications
applications. y allowsdirectfeedbackintocomputersystem
p y
(B) Telescopic
Tl i gauge 2. Fl
Flatness
y Thehighlysensitivemachinemeasurespartsdownto Disadvantages,
((C)) Transfer callipers
p 33. Internal diameter
thefractionofaninch. y Costly
C l
(D) Autocollimator 4. Roughness
y Specifically,aCMMcontainsmanyhighlysensitiveair y fixturingiscritical
g
Codes:A
d B C D A B C D
bearingsonwhichthemeasuringarmfloats. y requiresaverygoodtolerancemodel
(a) 4 1 2 3 (b) 4 3 1 2
(c) 4 2 1 3 (d) 3 1 2 4
GATE 2014
GATE2014
The diameter of a recessed ring was measured by using two GATE2016
spherical
h i l balls
b ll off diameter
di d2 = 60
6 mm andd d1 = 40 mm as For the situation shown in the figure below the
shown in the figure. expression for H in terms of r, R and D is
The distance
H2 = 35.55 H2 H1 (a) H = D + r2 + R2
mm and d1 Diameter
H1 = 20.55 C
(b) H = (R + r) + (D + r)
mm. Th
The
diameter (D, H (c) H = (R + r) + D2 R2
A B
i mm)) off the
in th R (d) H = (R + r) + 2D(R + r) D2
ring gauge is
.
Recessed Ring
D
265 266
d2 Diameter
g
MetalForming opposing dies so that the die shapes are imparted to the
work.
y
y
Billet: is hot rolled from a bloom and is square,
side or larger.
Sl b is
Slab: i the
th hot
h t rolled
ll d ingot
i t or bloom
bl
square 1.5
1 5 in.
rectangular
t
in on a
l cross
y Extrusion: The work material is forced to flow section 10 in. or more wide and 1.5 in. or more thick.
through a die opening taking its shape
4 5 6
SheetFormingProcesses
y In
I sheet
h metall working
ki operations,
i the
h crosssection
i off StrainHardening
Strain Hardening GATE1995
workpiece does not changethe material is only
y When metal is formed in cold state,
state there is no A test
t t specimen
i i stressed
is t d slightly
li htl beyond
b d the
th
subjected to shape changes.
recrystalization
y of g
grains and thus recoveryy from yield point and then unloaded.
unloaded Its yield strength
y The
Th ratio
i crosssection
i area/volume
/ l i very high.
is hi h
grain distortion or fragmentation does not take
y Sheet metalworking operations are performed on thin (a) Decreases
(less than 5 mm) sheets, strips or coils of metal by means place.
((b)) Increases
off a set off tools
l called
ll d punch
h and
d die
di on machine
hi toolsl y As grain deformation proceeds, greater resistance
called stamping presses. ((c)) Remains same
t this
to thi action
ti results
lt in
i increased
i d hardness
h d and
d
y They are always performed as cold working operations. (d) Become equal to UTS
strength i.e. strain hardening.
7 8 9
For-2018 (IES,GATE & PSUs) Page 67 of 213 Rev.0
IES2013
Statement (I): At higher strain rate and lower y Rx temp.
temp depends on the amount of cold work a material
temperature structural steel tends to become brittle. RecrystallisationTemperature(Rxtemp.) has already received. The higher the cold work, the lower
Statement (II): At higher strain rate and lower y The
Th minimum
i i temperature at which
hi h the
h completed
l d would
ld be
b the
h RxR temp.
temperature
p the yyield strength
g of structural steel tends recrystallisation of a cold worked metal occurs within a y Rx temp.
temp varies between 1/3 to melting paint.
paint
to increase. specified period of approximately one hour.
y For Pure metal Rx temp. = 0.3 x Melting temp.
( ) Both
(a) B th Statement
St t t (I) and
d Statement
St t t (II) are individually
i di id ll y Rx temp.
temp decreases strength and increases ductility.
ductility (Kelvin).
true and Statement (II) is the correct explanation of y If working
g above Rx temp.,
p , hotworking
g p
process
Statement (I)
() y For Alloy Rx temp.
temp = 0.5
0 5 x Melting temp.
temp (Kelvin).
(Kelvin)
whereas working below are coldworking process.
(b) Both Statement (I) and Statement (II) are individually y Rx temp.
p of lead and Tin is below room temp.
p
y It
I involves
i l replacement
l off coldworked
ld k d structure by
b a
true but Statement (II) is not the correct explanation of y Rx temp. of Cadmium and Zinc is room temp.
new set of strainfree, approximately equiaxed grains to
Statement (I)
replace all the deformed crystals. Contd. y Rx temp. of Iron is 450oC and for steels around 1000C
(c) Statement (I) is true but Statement (II) is false
(d) Statement (I) is false but Statement (II) is true y Finer
Fi i the
is h initial
i i i l grain
i size;
i lower
l will
ill be
b the
h Rx
R temp
10 11 12
IES 2016
IES2016 Graingrowth
h Malleability
ll b l
The recrystallization behaviour of a particular metal
y Graingrowthfollowscompletecrystallizationifthematerials y Malleability is the property of a material whereby it can
alloy is specified in terms of recrystallization
leftatelevatedtemperatures.
p
temperature, which is typically 1/3rd of the absolute b shaped
be h d when
h cold
ld by
b hammering
h or rolling.
ll
y Graingrowthdoesnotneedtobeprecededbyrecoveryand
melting temperature of a metal or an alloy and depends recrystallization;itmayoccurinallpolycrystallinematerials.
ll ll l ll l y A malleable
ll bl material
i l is
i capable
bl off undergoing
d i plastic
l i
on several factors including
g the amount of y Incontrarytorecoveryandrecrystallization,drivingforce deformation without fracture.
fracture
1. cold working and purity of the metal and alloy forthisprocessisreductioningrainboundaryenergy.
y A malleable material should be plastic but it is not
2. hot working and purity of the metal and alloy y Inpracticalapplications,graingrowthisnotdesirable.
Which of the above is/are correct? y Incorporationofimpurityatomsandinsolublesecondphase essential to be so strong.
g
(a) 1 only (b) 2 only particlesareeffectiveinretardinggraingrowth. y Lead, soft steel, wrought iron, copper and aluminium are
(c) Both 1 and 2 (d) Neither 1 nor 2 y Graingrowthisverystronglydependentontemperature.
13 14 some materials in order of diminishing malleability. 15
AdvantagesofColdWorking
d f ld k
1. Better accuracy, closer tolerances
y Workingbelowrecrystalizationtemp.
2. Better surface finish
g
ColdWorking 3. Strain hardening increases strength and hardness
16 17 18
For-2018 (IES,GATE & PSUs) Page 68 of 213 Rev.0
DisadvantagesofColdWorking
d f ld k
1. Equipmentofhigherforcesandpowerrequired
2. Surfacesofstartingworkpiecemustbefreeofscaleand
S f f t ti k i tb f f l d
dirt
3. Ductilityandstrainhardeninglimittheamountofforming
thatcanbedone
4. Insomeoperations,metalmustbeannealedtoallow
H tW ki g
HotWorking
furtherdeformation
55. Somemetalsaresimplynotductileenoughtobecold
py g
worked. 19 20 21
AdvantagesofHotWorking DisadvantagesofHotWorking
1. The porosity of the metal is largely eliminated. 1. It requires expensive tools.
y Workingaboverecrystalizationtemp. 2 The grain structure of the metal is refined.
2. refined 2 It produces poor surface finish,
2. finish due to the rapid
3. The impurities like slag are squeezed into fibers and oxidation and scale formation on the metal surface.
di ib d throughout
distributed h h the
h metal.l 3. Due
D to the
h poor surface
f fi i h close
finish, l tolerance
l
4. The mechanical p
4 properties
p such as toughness,
g , cannot be maintained.
percentage elongation, percentage reduction in area, and
resistance to shock and vibration are improved due to
the refinement of grains.
22 23 24
Annealing
g
MicroStructuralChangesinaHot
Mi St t l Ch i H t IES 2016
IES2016 Annealing relieves the stresses from cold working three
Statement (I) : Pursuant to p
plastic deformation of
WorkingProcess(Rolling)
Working Process (Rolling) metals, the mechanical properties of the metals get
stages: recovery,
recovery recrystallization and grain growth.
growth
During recovery, physical properties of the coldworked
changed.
material
i l are restored
d without
ih any observable
b bl change
h i
in
Statement (II) : Mechanical properties of metals microstructure.
d
depend d on grain
i size
i also
l which
hi h gets
t changed
h d by
b
plastic deformation.
(a) Both Statement (I) and Statement (II) are individually true and
Statement ((II)) is the correct explanation
p of Statement ((I).
)
(b) Both Statement (I) and Statement (II) are individually true but
Statement (II) is not the correct explanation of Statement (I).
(c) Statement (I) is true but Statement (II) is false.
(d) Statement
St t t (I) is
i false
f l but
b t Statement
St t t (II) is
i true
t
25 26 27
For-2018 (IES,GATE & PSUs) Page 69 of 213 Rev.0
W F i
WarmForming IsothermalForming
h l
y Deformation produced at temperatures intermediate to IES2011
hot and cold forming is known as warm forming. y During hot forming, cooler surfaces surround a hotter Assertion (A): Lead, Zinc and Tin are always hot
y Compared to cold forming,
forming it reduces loads,
loads increase interior and the variations in strength can result in non
interior, non worked.
material ductility. uniform deformation and cracking of the surface.
Reason (R) : If they are worked in cold state
they cannot retain their mechanical properties.
properties
y Compared to hot forming, it produce less scaling and
y For temp.sensitive materials deformation is performed (a) Both A and R are individually true and R is the
decarburization, better dimensional precision and
smoother surfaces. under isothermal conditions. correct explanation of A
y Warm forming
f i i a precision
is i i f i
forging operation
i carried
i d y The
Th dies
di or tooling
li must be
b heated
h d to the
h workpiece
k i (b) Both A and R are individually true but R is NOT
out at a temperature range between 550950C. It is the correct explanation of A
temperature,
p , sacrificing
g die life for p
product q
quality.
y
useful for forging of details with intricate shapes, with ( ) A is true but
(c) b R is false
f l
desirable grain flow, good surface finish and tighter y Close tolerances, low residual stresses and uniform metal (d) A is false but R is true
dimensional tolerances. 28
flow.
29 30
(c) Normalizing
(d) Annealing
31 32 33
34 35 36
For-2018 (IES,GATE & PSUs) Page 70 of 213 Rev.0
IES 2008 IES 2008 IES 2004
Consider
C id the h following
f ll i statements: Cold
C ld forging
f i results
l ini improved
i d quality
li dued to Assertion
A i (A):
(A) Cold
C ld workingki off metals
l resultsl in i
1. Metal forming g decreases harmful effects of which of the following? increase of strength and hardness
impurities and improves mechanical strength. 1. Better mechanical properties of the process. Reason (R): Cold working reduces the total number
2 Metal working process is a plastic deformation
2. 2 Unbroken grain flow.
2. flow of dislocations per unit volume of the material
process. 3. Smoother finishes. (a) Both A and R are individually true and R is the
3. Very intricate shapes can be produced by forging 4. High pressure. correct explanation
l off A
process
p ocess as co
compared
pa ed to cast
casting
gpprocess.
ocess. S l t the
Select th correctt answer using
i the
th code
d given
i b l
below: (b) Both
ot A aand d R aaree individually
d v dua y ttrue
ue but R iss not
ot tthee
Which of the statements given above are correct? correct explanation of A
(a) 1, 2 and 3 (b) 1, 2 and 4
( ) 1, 2 and
(a) d3 (b) 1 and d 2 only
l ( ) A is
(c) i true
t b t R is
but i false
f l
(c) 2, 3 and 4 (d) 1, 3 and 4
(c) 2 and 3 only (d) 1 and 3 only (d) A is false but R is true
37 38 39
IAS2002 IES2008
Assertion
A i (A):(A) There
Th is
i good d grain
i refinement
fi in
i hot
h Which one of the following is correct?
GATE2017
working.
It is desired to make a product having TT
Reason (R): In hot working physical properties are Malleability is the property by which a metal or
shaped crosssection from a rectangular
generally improved.
improved alloy
ll can be
b plastically
l i ll deformed
d f d by
b applying
l i aluminium
l bl k Which
block. h h one off theh
(a) Both A and R are individually true and R is the
( ) Tensile
(a) T il stress
t (b) B di stress
Bending t following processes is expected to provide
correct explanation
l off A
the highest strength of the product?
(b) Both
ot A aand d R aaree individually
d v dua y ttrue
ue but R iss not
ot tthee (c) Shear stress (d) Compressive stress
correct explanation of A (a) Welding (b) Casting
( ) A is
(c) i true
t b t R is
but i false
f l (c) Metal forming (d) Machining
(d) A is false but R is true
49 50 51
Rolling
y Definition: The process of plastically deforming GATE2013
metal by passing it between rolls. In a rolling process, the state of stress of the
y Most widely used, high production and close material undergoing deformation is
g
Rolling tolerance. (a) pure compression
y Friction between the rolls and the metal surface (b) pure shear
produces high compressive stress. (c) compression and shear
y Hotworking (unless mentioned cold rolling.) (d) tension and shear
BySKMondal
52 y Metal will undergo biaxial compression. 53 54
For-2018 (IES,GATE & PSUs) Page 72 of 213 Rev.0
HotRolling
y Done above the recrystallization temp.
Ch
ChangeingrainsstructureinHotrolling
i i t t i H t lli IAS 2001 ColdRolling
Consider
C id the
h following
f ll i characteristics
h i i off rolling
lli
y Done below the recrystallization temp..
process:
1. Shows work hardening effect y Products are sheet, strip, foil etc. with good
2 Surface finish is not good
2.
3. Heavy reduction in areas can be obtained
surface finish and increased mechanical strength
Which of these characteristics are associated with hot with close product dimensions.
rolling?
(a) 1 and 2 (b) 1 and 3 y Performed on fourhigh or clustertype rolling
Hot rolling is an effective way to reduce grain size in (c) 2 and 3 (d) 1, 2 and 3 mills. (Due to high force and power)
metals for improved
p strength
g and ductility.
y
58 59 60
RingRolling
ISRO2006 y Ring rolls are used for tube rolling, ring rolling.
Whi h off the
Which th following
f ll i processes would
ld y As the rolls squeeze and rotate, the wall thickness is
produce strongest components? reduced
d d and
d the
h diameter
di off the
h ring
i increases.
i
(a) Hot rolling y Shaped
Sh d rolls
ll can be
b used
d to
t produce
d a wide
id variety
i t off
((b)) Extrusion crosssection
cross section profiles.
profiles
((c)) Cold rolling
g y Ring rolls are made of spheroidized graphite bainitic and
(d) Forging pearlitic matrix or alloy cast steel base.
61 62 63
For-2018 (IES,GATE & PSUs) Page 73 of 213 Rev.0
Sheetrolling
ISRO2009 y In sheet rolling we are only attempting to reduce the
Ring rolling is used cross section thickness
h k off a material.
l
(a) To decrease the thickness and increase
diameter
(b) To
T increase
i th thickness
the thi k off a ring
i
(c) For producing a seamless tube
(d) For producing large cylinder
64 65 66
RollForming RollBending
y A continuous form of threepoint bending is roll
bending, where plates, sheets, and rolled shapes can
be bent to a desired curvature on forming rolls.
67 68 69
70 71 72
For-2018 (IES,GATE & PSUs) Page 74 of 213 Rev.0
Threadrolling Threadrollingcontd.
y Used to produce threads in substantial quantities. y Major diameter is always greater than the diameter of the
f
formed
d by
b rolling
lli a thread
h d blank
bl k between
b h d
hardened
d dies
di y Blank
Bl k diameter
di i little
is li l larger
l (
(0.002 i h) than
inch) h the
h pitch
i h
that cause the metal to flow radially into the desired diameter of the thread.
thread
shape.
p y Restricted to ductile materials.
materials
y No metal is removed, g
greater strength,
g smoother, harder,
and more wearresistant surface than cut threads.
73 74 75
( ) Hardmaterials
(c) ( ) A little large than the minor diameter of the thread
(c)
(d) Noneoftheabove
N f h b (d) A little
li l larger
l than
h the
h pitch
i h diameter
di off the
h thread
h d
76 77 78
Manufactureofgearsbyrolling
y The straight and helical teeth of disc or rod type external
steell gears off small
ll to medium
d d
diameter and
d module
d l are
generated by cold rolling.
rolling
Planetarymill Camber
y Consist of a pair of heavy backing rolls surrounded by a large
number of planetary rolls.
y Each planetary roll gives an almost constant reduction to the
slab as it sweeps out a circular path between the backing rolls
and the slab.
y As each pair of planetary rolls ceases to have contact with the
work piece, another pair of rolls makes contact and repeat
that
h reduction.
d i
y The overall reduction is the summation of a series of small
reductions
d ti b each
by h pair
i off rolls.
ll Therefore,
Th f th planetary
the l t mill
ill
can reduce a slab directly to strip in one pass through the
mill.
mill
y The operation requires feed rolls to introduce the slab into
the mill, and a pair of planishing rolls on the exit to improve
the surface finish. y Camber can be used to correct the roll deflection (at only
88 89 one value of the roll force). 90
For-2018 (IES,GATE & PSUs) Page 76 of 213 Rev.0
IES 1993 LubricationforRolling IAS 2004
In order to get uniform thickness of the plate by y Hot rolling of ferrous metals is done without a lubricant. Assertion
A i (A):
(A) Rolling
R lli requires
i high
hi h friction
f i i which
hi h
increases forces and power consumption.
rolling
ll process, one provides
d y Hot rolling of nonferrous metals a wide variety of Reason (R): To prevent damage to the surface of the
( ) Camber
(a) C b on the
h rolls
ll compounded
d d oils,
il emulsions
l i and
d fatty
f acids
id are used.
d rolled products,
products lubricants should be used. used
(a) Both A and R are individually true and R is the
(b) Offset
Off t on the
th rolls
ll y Cold
C ld rolling
lli l bi
lubricants
t are watersoluble
t l bl oils,
il low
l correct explanation
l off A
(c) Hardening of the rolls viscosity lubricants,
lubricants such as mineral oils,
oils emulsions,
emulsions (b) Both
ot A aand d R aaree individually
d v dua y ttrue
ue but R iss not
ot tthee
correct explanation of A
(d) Antifriction bearings paraffin and fattyy acids.
p
( ) A is
(c) i true
t b t R is
but i false
f l
(d) A is false but R is true
91 92 93
DefectsinRolling DefectsinRolling
Defects Whatis Cause Anisotropy
Surface Scale, rust, Inclusions and
Materialdevelopsanisotropyduringcoldrollingofsheet
Materialdevelopsanisotropyduringcoldrollingofsheet GATE
GATE 2009(PI)
2009 (PI)
metal
Defects scratches,, impurities
p in the
Three principal true strain A i t
Anisotropy i rolled
in ll d components
t is
i caused
d by
b
pits, cracks materials
L (a) changes in dimensions
Wavy edges Strip is Due to roll Inlengthdirection, l = ln f
Lo
thinner along g bendingg edges
g (b) scale formation
W
its edges than elongates more Inwidthdirection, w = ln f
at its centre.
centre and buckle.
buckle Wo (c) closure of defects
t
Inthethicknessdirection, t = ln f
Alligatoring Edge breaks Non uniform
Nonuniform to
(d) grain orientation
deformation For isotropicmaterials, w = t but in a cold rolled sheet w t
w
Anisotropyratio ( r ) =
94 t 95 96
Example
A rectangular block 100 mm x 20 mm x 2 mm IES2003
A
Assertion
ti (A):
(A) While
Whil rolling
lli metal
t l sheet
h t in
i rolling
lli
is elongated to 130 mm. If the anisotropy
mill the edges are sometimes not straight and flat
mill,
ratio = 2,, find true strain in all directions. but are wavy.
y FormulainRolling
Reason (R) : Non uniform mechanical properties
of the flat material rolled out result in waviness of
the edges.
97 98 99
For-2018 (IES,GATE & PSUs) Page 77 of 213 Rev.0
GeometryofRollingProcess Draft GATE2007
y Total
T l reduction
d i or draft
d f taken
k ini rolling.
lli The thickness of a metallic sheet is reduced from an
[ mustbeinradian]
rolled
ll d to 20 mm thickness.
h k Roll
mm and it rotates at 100 rpm.
ll is off diameter
d 600
rpm The roll strip contact
tan
length will be
((a)) 5 mm ((b)) 39 mm
GATE 2016
GATE-2016 GATE 2015
GATE-2015 GATE 2015
GATE-2015
A 300 mm thick slab is being cold rolled using In a rolling operation using rolls of diameter In
I a slab
l b rolling
lli operation
i , the
h maximum
i
roll
ll off 600
6 mm diameter.
di t If the
th coefficient
ffi i t off 500 mm , if a 25 mm thick
thi k plate
l t cannott be
b thickness reduction(h)max is given by hmax =
R
R,
friction is 0 08,
0.08, the maximum possible reduced to less than 20 mm in one pass, the where R is the radius of the roll and is the co
reduction (in mm) is ____________ coefficient of friction between the roll and the efficient of friction between the roll and the sheet.
ho h f min = 2 R
limit to the possible reduction in thickness in one
pass. rolls
ll to reduce
d thickness
h k without
h any change
h in its
Reason (R): The reduction possible in the second width The friction coefficient at the workroll
width. work roll
pass is less than that in the first pass.
interface is 0.1. The minimum possible thickness of
( ) Both
(a) h A and d R are individually
d d ll true and d R is the
h
correct explanation of A the sheet that can be produced in a single pass is
(b) Both A and R are individually true but R is not the
(a) 1.0 mm (b) 1.5 mm
correct explanation of A
(c) A is true but R is false (c) 2.5 mm (d) 3.7 mm
(d) A is false but R is true
115 116 117
For-2018 (IES,GATE & PSUs) Page 79 of 213 Rev.0
Numberofpassneeded G
GATE 20 ( )
2011(PI) IES 2001
The
Th thickness
hi k off a plate
l is
i reduced
d d from
f 30 mm to 10 A strip is to be rolled from a thickness of 30 mm to
n=
q rolls of diameter 600 mm. Assume that there is no diameter 300 mm.
mm The coefficient of friction for
hmax
change in width. If the coefficient of friction unaided bite should nearly be
between the rolls and the work piece is 0.1, the
((a)) 0.35
35 ((b)) 0.55
minimum number of passes required is
((c)) 0.255 ((d)) 0.077
(a) 3 (b) 4 (c) 6 (d) 7
NeutralPointandNeutralPlane
The point
Th i where
h roll
ll velocity
l i equals
l
GATE2014(PI) work velocity is known as the noslip V0 =inputvelocity
A 80
8 mm thick
hi k steell plate
l with
i h 400 mm width
id h is
i point
i t or the
th neutral
t l point.
i t Vf=finaloroutputvelocity GATE1990(PI)
GATE1990 (PI)
rolled to 40 mm thickness in 4 passes with equal R rollradius
R=rollradius
reduction in each pass, by using rolls of 800 mm Whil rolling
While lli a strip
t i the
th peripheral
i h l velocity
l it off
ho =backheight
diameter. Assuming g the pplanestrain deformation,, the roll is .A..than
A than the entry velocity of the
hf=outputorfinal
fi l
what is the minimum coefficient of friction
thickness strip
p and is B ..the exit velocity
y of the
required for unaided rolling to be possible?
=angleofbite
(a) 0.111 (b) 0.158 (c) 0.223 (d) 0.316 strip.
N N neutralpointorno
NN=neutralpointorno
slippoint (a) less than/greater less
Vr Vo
Backward slip = 100% TotheleftoftheNeutralPoint:
Vr (b) Greater than/less than
Velocityofthestrip<Velocityoftheroll
V f Vr
Forward slip = 100% TotherightoftheNeutralPoint:
121 Vr Velocityofthestrip>Velocityoftheroll
122 123
IES 2014
IES IES 2002
In the process of metal rolling operation, along the arc GATE2008(PI)
off contact ini the
h roll ll gap there
h is
i a pointi called
ll d the
h In a rolling process, thickness of a strip is reduced In rolling a strip between two rolls, the position of
neutral point, because
(a) On one side of this point, the work material is in tension f
from 4 mm to 3 mm using 300 mm diameter
d rolls
ll the
h neutrall point in the
h arc off contact does
d not
and on the other side,, the work material is in compression
p
rotating at 100 rpm.
rpm The velocity of the strip in depend on
(b) On one side of this point, the work material has velocity
greater than that of the roll and on the other side,
side it has (m/s) at the neutral point is (a) Amount of reduction (b) Diameter of the rolls
velocity lesser than that of the roll
((a)) 1.57
57 ((b)) 33.14
4 ((c)) 47
47.10 ((d)) 94
94.20 (c) Coefficient of friction (d) Material of the rolls
( ) On
(c) O one side id off this
thi point,
i t the
th work k material
t i l has
h rough h
surface finish and on the other side, the work material has
very fine
fi finish
fi i h
(d) At this ppoint there is no increase in material width, but
on either side of neutral point, the material width increases
124 125 126
For-2018 (IES,GATE & PSUs) Page 80 of 213 Rev.0
SelectedQuestions C ti it E
ContinuityEquation
ti GATE2014
y Generally rolling increases the
The effect of friction on the rolling mill is work width from an initial value A mild steel plate has to be rolled in one pass such
of bo to a final one of bf and this
(a) always bad since it retards exit of reduced metal is called spreading. that the final plate thickness is 2/3rd of the initial
(b) always good since it drags metal into the gap between y The
Th inlet
i l and
d outlet
l volume
l thickness,
hi k with
i h the
h entrance speed
d off 10 m/min
/ i
rates of material flow must be
th rolls
the ll the
h same, thath is,
i and roll diameter of 500 mm.
mm If the plate widens
byy 2% during
g rolling,
g, the exit velocityy ((in m/min)
/ )
(c) advantageous before the neutral point hobovo = hf bfvf
where vo and vf are the entering
g is
(d) disadvantageous after the neutral point
and exiting velocities of the
work.
127 128 129
Force,TorqueandPower
ElongationFactororElongationCoefficient GATE1992(PI)
L1 Ao If the elongation factor during rolling of an
E= = for single pass ingot is 1.22. The minimum number of passes
Lo A1
needed
d d to produce
d a section
i 250 mm x 250 mm
L A
En = n = o f n pass
for from an ingot of 750 mm x 750 mm are
Lo An (a) 8 (b) 9
(c) 10 (d) 12
Will b
be
discussed
130 131 in class 132
Forging ClosedDieforging
g g
y Forging
g g p g p
process is a metal working process byy which
metals or alloys are plastically deformed to the desired
BySKMondal
y
142 143 144
For-2018 (IES,GATE & PSUs) Page 82 of 213 Rev.0
IES2013
IES2016 Statement (I): The dies used in the forging process are OpenandCloseddieforging
d l dd f
made in pair.
pair y Depending
D di upon complexity
l i off the
h part forging
f i is
i
Statement (II): The material is pressed between two carried out as open die forging and closed die forging.
Ill
Illustrate the
h difference
diff b
between surfaces and the compression force applied, gives it a
shape.
p y In open die forging, the metal is compressed by repeated
(i) open die forging and bl
blows b a mechanical
by h i l h
hammer and
d shape
h i
is
(a) Both Statement (I) and Statement (II) are individually manipulated manually.
true and Statement (II) is the correct explanation of
(ii) closed die forging with appropriate Statement (I) y In closed die forging, the desired configuration is
sketches (b) Both Statement (I) and Statement (II) are individually obtained
b i d byb squeezing i the
h workpiece
k i b
between two
true but Statement ((II)) is not the correct explanation
p of shaped and closed dies.
[4Marks] Statement (I)
(c) Statement (I) is true but Statement (II) is false
145
(d) Statement (I) is false but Statement (II) is true 146 147
AdvantagesofForging
d f DisadvantagesofForging
d f IES 1996
y Discrete
Di shape
h off product
d can be
b produced.
d d y Costly
C l Which one of the following is an advantage of
y Mechanical properties and reliability of the materials y Poor dimensional accuracy and surface finish.
finish forging?
increases due to improve in crystal structure.
y Forging operations are limited to simple shapes and has
( ) Good
(a) G d surface
f fi i h
finish
y In forging favorable grain orientation of metal is limitations for parts having undercuts, reentrant
obtained that strengthen the component but forging surfaces etc
surfaces, (b) Low
L tooling
t li costt
distorts the previously created unidirectional fibre.
(c) Close tolerance
y Forging reduces the grain size of the metal, which
increases strength and toughness.
toughness (d) Improved physical property.
property
y Fatigue and creep strength increases.
148 149 150
Flash
l h Flash
l h Contd IES 2014
The
Th excess metall added
dd d to the
h stockk to ensure complete
l y A flash
fl h acts as a cushion
hi for
f impact
i blows
bl from
f the
h In
I hot
h die di forging,
f i thin
hi layer
l off material
i l all
ll around
d
filling of the die cavity in the finishing impression is finishing impression and also helps to restrict the the forging is
called Flash. outward flow of metal, thus helping in filling of thin ribs (a) Gutter space, which fills up hot gases
and bosses in the upper
pp die. (b) Flash,
Flash the width of it is an indicator of the pressure
y The amount of flash depends on the forging size and developed in the cavity
may vary from 10 to 50 per cent. (c) Coining, which indicates the quality of the forging
y The
Th forging
f i l d can be
load b decreased
d d by
b increasing
i i the
h (d) Cavity,
Cavity which is filled with hot impurities in the
flash thickness. material
IES2015 Sequentialstepsinvolvedincloseddieforging
Fulleringor Reducingcrosssectionandmakingitlonger.
Which of the following statements apply to provision swaging
GATE1989(PI) of flash gutter and flash land around the parts to be Edgingorrolling Preformshape.Gathersthematerialas
requiredinthefinalforging.
Atth l th
Atthelasthammerstroketheexcessmaterialfrom
t k th t i lf forged? Bending Requiredforthosepartswhichhaveabent
thefinishingcavityofaforgingdieispushed 1. Small cavities are provided which are directly outside shape
p
the die impression. Drawingorcogging Likefulleringbutc/sofonlyoneend is
into.. 2 The volume of flash land and flash gutter should be
2. reduced
about 20%25% of the volume of forging. Flattening Flattenthestocksothatitfitsproperlyinto
3. Gutter
G tt is i provided
id d to
t ensure completel t closing
l i off the
th thefinishingimpression.
thefinishingimpression
die. Blocking Semifinishingimpression,Impartstothe
(a) 1 and 2 only (b) 1 and 3 only f i it
forgingitsgeneralbutnotexactorfinalshape.
lb t t t fi l h
((c)) 1,, 2 and 3 ((d)) 2 and 3 onlyy Finishing Finalimpression,FlashlandandGutter
provided tothedie.
169 170
Trimmingorcutoff Removalofflashpresent aroundforging 171
For-2018 (IES,GATE & PSUs) Page 85 of 213 Rev.0
Example
l IES 1998 IES 2001
Which one of the following processes is most Intheforgingoperation,fulleringisdoneto
commonly
l used
d for
f the
h forging
f off bolt
b l heads
h d off (a) Drawoutthematerial
hexagonal shape? (b) Bendthematerial
(a) Closed die drop forging ( ) Upsetthematerial
(c)
(b) Open die upset forging (d) Extrudingthematerial
E di h i l
(c) Close die press forging
((d)) Open
p die p
progressive
g forging
g g
172 173 174
PressForging
g g IES 2011
IES2011
y Metal is squeezed gradually by a hydraulic or mechanical AdvantagesofPressForgingoverDropForging Consider the following statements :
press and component is produced in a single closing of 1. Any metal will require some time to undergo
y Press forging is faster than drop forging
die, hence the dimensional accuracy is much better than complete
p plastic deformation p
p particularly
y if
d
drop f i
forging. y Alignment of the two die halves can be more easily deforming metal has to fill cavities and corners of
small radii.
maintained
i i d than
h with
i h hammering.
h i
2. For larger work piece of metals that can retain
y Structural
St t l quality
lit off the
th product
d t is
i superior
i tot drop
d toughness
h at forging
f i temperature it i is
i preferable
f bl to
forging.
forging use forge press rather than forge hammer.
(a) 1 and 2 are correct and 2 is the reason for 1
y With ejectors in the top and bottom dies, it is possible to (b) 1 and 2 are correct and 1 is the reason for 2
handle reduced die drafts. (c) 1 and 2 are correct but unrelated
(d) 1 only correct
187 188 189
For-2018 (IES,GATE & PSUs) Page 87 of 213 Rev.0
MachineForging
h UpsetForging RollForging
ll
y Unlike the drop or press forging where the material is y Increasing the diameter of a material by compressing its y When the rolls are in the open position, the heated stock
d
drawn out, in machine
h f
forging, the
h materiall is only
l upset l
length.
h is advanced
d d up to a stop. As the
h rolls
ll rotate, they
h grip and
d
to get the desired shape.
shape y Employs
E l split
li dies
di that
h contain
i multiple
l i l positions
ii or roll down the stock.
stock The stock is transferred to a second
cavities.
cavities set of grooves. The rolls turn again and so on until the
piece is finished.
RollForging
ll Contd.
SkewRolling SmithForging
h
y A rapid
id process. y Skew rolling produces y Blacksmith
Bl k i h uses this
hi forging
f i method
h d
metal ball y Quality of the product depends on the skill of the
y Round stock is fed operator.
continuously to two y Not used in industry.
p y
specially designed
g
opposing rolls.
ForIESOnly
IES 2008
IES Hi h V l it F i (HVF)
HighVelocityForming(HVF)
IES 2005 Match ListI with ListII and select the correct answer using
Match
M t h List
Li t I (Type
(T off Forging)
F i ) withith List
Li t II (Operation)
(O ti ) the code given below the lists: y The
ep ocess de
process o s metals
deforms eta s by us g ve
using veryy high
g ve oc t es,
velocities,
and select the correct answer using the code given ListI (Forging Technique) ListII (Process) provided on the movements of rams and dies.
below the Lists: A SmithForging
A.SmithForging 11. Materialisonlyupsettogetthe y As K.E V2, high energy is delivered to the metal with
List I List II desiredshape relativelyy small weights
g ((ram and die).
)
A Drop
A. D F i
Forging 1. M l is
Metal i gripped
i d in
i theh dies
di andd B.DropForging 2.Carriedoutmanuallyopendies
pressure is applied on the heated end y Cost and size of machine low.
B. Press Forging 2. Squeezing action C PressForging
C.PressForging 3 Done in closed impression dies by
3.
p Forging
C. Upset g g 33. Metal is p placed between rollers and
hammers in blows y Ram strokes short (due to high acceleration)
pushed D.MachineForging 4. Done in closed impression dies by
y Productivity high, overall production cost low
D. Roll Forging
g g 4 4. Repeated
p hammer blows continuous squeezing
q g force
A B C D A B C D Code: A B C D A B C D y Used for Alloy steel, titanium, Al, Mg, to fabricate one
(a) 4 1 2 3 (b) 3 2 1 4 (a) 2 3 4 1 (b) 4 3 2 1 piece complex components of smaller size like valve,
(c) 4 2 1 3 (d) 3 1 2 4196 (c) 2 1 4 3 (d) 4 1 2 3 197 rocket component. 198
For-2018 (IES,GATE & PSUs) Page 88 of 213 Rev.0
ForIESOnly
LubricationforForging
b f ForgingDefects
f ForgingDefects
f Contd.
y Lubricants influence: friction, wear, deforming forces y Unfilled Sections: Die cavity is not y Scale
S l Pits:
Pi Irregular
I l depressions
d i on the
h surface
f due
d to
improper cleaning of the stock.
and
d flow
fl off materiall in diecavities,
d nonsticking,
k completely
l l filled,
f ll d due
d to improper y Die Shift: Due to Misalignment of the two die halves or
thermal barrier.
barrier design of die making the two halves of the forging to be of improper
shape.
y For hot forging: graphite,
graphite MoS2 and sometimes molten y Cold Shut or fold: A small crack at y Flakes:
l k Internall ruptures caused d by
b the
h improper
g
glass. the corners and at right
g angles
g to cooling.
y Improper Grain Flow: This is caused by the improper
y For cold forging:
g g mineral oil and soaps.
p the forged surface. Cause: improper
design of the die,
die which makes the flow of metal not
y In hot forging, the lubricant is applied to the dies, but in
design of the die flowing the final intended directions.
ForgingDefects
f Contd. IAS 1998 IES2011
y Forging Laps: These are folds of metal squeezed The
Th forging
f i defect
d f due
d to hindrance
hi d to smooth
h flow
fl Assertion (A) ( ) : Hot tears occur during
d forging
f
of metal in the component called 'Lap' occurs because of inclusions in the blank material
together
h during
d f
forging. They
h have
h irregular
l contours because Reason (R) : Bonding between the inclusions
and occur at right angles to the direction of metal flow.
flow (a) The corner radius provided is too large and the p parent material is through
g p physical
y
and chemical bonding.
(b) The corner radius provided is too small
y Hot tears and thermal cracking: These are surface (a) Both A and R are individually true and R is the
(c) Draft is not provided correct explanation of A
cracks occurring
g due to nonuniform cooling
g from the (d) The shrinkage allowance is inadequate (b) Both A and R are individually true but R is NOT
forging stage or during heat treatment. the correct explanation of A
( ) A is true but
(c) b R is false
f l
((d)) A is false but R is true
205 206 207
For-2018 (IES,GATE & PSUs) Page 89 of 213 Rev.0
IES2013
B lli
Barrelling Consider
C id the
h following
f ll i statements pertaining i i to the h
opendie forging of a cylindrical specimen between
GATE2008(PI)
GATE 2008 (PI) two flat dies:
Matchthefollowing
1 Lubricated specimens show more surface movement
1.
Group1 Group2 than unlubricated ones.
P Wrinkling
P. 1 Upsetting
1.Upsetting 2. Lubricated
b d specimens show
h l
less surface
f movement
Q.Centreburst 2.Deepdrawing than unlubricated ones.
R.Barrelling 3.Extrusion 3. Lubricated specimens show more barrelling than un
S C ld h t
S.Coldshut 4.Closeddieforging
Cl ddi f i lubricated ones.
ones
4. Lubricated specimens shows less barrelling than un
(a)P 2,Q 3,R 4,S1 (b)P 3,Q 4,R 1,S2 lubricated ones.
(c)P 2,Q
(c)P 2 Q 3,R
3 R 1,S
1 S4
4 (d)P 2,Q
(d)P 2 Q 4,R
4 R 3,S
3 S1
1 Which of these statements are correct?
Inhomogeneousdeformationwithbarrelingoftheworkpiece (a) 1 and 3 (b) 1 and 4 (c) 2 and 3 (d) 2 and 4210
208 209
ForIESOnly
DieMaterialsShouldhave
l h ld h GATE2010(PI)
y Goodhardness,toughnessandductilityatlowand
Goodhardness toughnessandductilityatlowand
Hot die steel, used for large solid dies in drop forging,
elevatedtemperatures
p
should
h ld necessarily
l have
h
y Adequatefatigueresistance
( ) high
(a) hi h strength
h and
d high
hi h copper content
y Sufficienthardenability
y Lowthermalconductivity (b) high
hi h hardness
h d and
d low
l hardenability
h d bilit
y Amenabilitytoweldrepair
A bili ld i (c) high toughness and low thermal conductivity
ForIESOnly
IES2013
IES 2013
Statement (I): In power forging energy is provided by TrueStress&TrueStrain
compressed d air
i or oil
il pressure or gravity.
it
Statement ((II):) The capacity
p y of the hammer is g given byy
True stress ( T ) = (1 + )
the total weight, which the falling pans weigh. L Ao do
(a) Both Statement (I) and Statement (II) are individually
True strain ( T ) = ln(1
( + ) = ln = ln = 2 ln d
Lo A
true and Statement (II) is the correct explanation of
S
Statement (I)
((b)) Both Statement ((I)) and Statement ((II)) are individuallyy
true but Statement (II) is not the correct explanation of
Statement (I)
(c) Statement (I) is true but Statement (II) is false
(d) Statement (I) is false but Statement (II) is true
214 215 216
For-2018 (IES,GATE & PSUs) Page 90 of 213 Rev.0
GATE2014 GATE1992,ISRO2012,VS2013 GATE2016
The relationship between true strain (T ) and Engineering strain of a mild steel sample is
The true strain for a low carbon steel bar
engineering strain (
( E ) in a uniaxiall tension test is
which is doubled in length by forging is recorded as 0.100%. The true strain is
( ) E =ln(1+
(a) l ( T ) (b) E =ln(1
(b) l ( T )
((a)) 0.307
3 7 (a) 0.010 %
( ) T =ln(1+
(c) l ( E ) (d) T =ln(1
(d) l ( E )
(b) 0.5 (b) 0.055 %
(c) 0.693
0 693 ((c)) 0.099
99 %
(d) 1.0
10 (d) 0.
0.101
0 %
217 218 219
GATE2007 GATE2016
In opendie forging, a disc of diameter 200
GATE2017(PI)
GATE2017 (PI) The value of true strain produced in
mm and height 60 mm is compressed A steell wire
i off 2 mm diameter
di i to be
is b drawn
d compressing a cylinder to half its original
without any barreling effect. The final f
from a wire
i off 5 mm diameter.
di t TheTh value
l off length is
diameter of the disc is 400 mm. The true true strain developed
de eloped is _____________(up
(up
(a) 0.69 (b) 0.69
strain is to three decimal places).
places)
(c) 0.5 (d) 0.5
(a) 1.986 (b) 1.686
StrainHardening&FlowStress
GATE 2017
GATE2017 y In the plastic region,
region the material behaviour is expressed
by the flow curve: AverageFlowStress
A rod of length 20 mm is stretched to make a rod = K n
Where K is strength coefficient and n is strainhardening y Average (mean) flow stress is not on the basis of
of length 40 mm. Subsequently, it is compressed (or workhardening)
work hardening) exponent and at UTS,
UTS = n instantaneous flow stress,
stress but on an average value over
the stress strain curve from the beginning of strain to
to make a rod of final length 10 mm. Consider the the final (maximum) value that occurs during
longitudinal
g tensile strain as p
positive and deformation.
K nf
compressive
p strain as negative.
g The total true g flow stress ( o ) =
Average
longitudinal
g strain in the rod is
1+ n
Here f is the maximum strain value during deformation.
((a)) 0.55 ((b)) 0.69
9 ((c)) 0.75
75 ((d)) 1.0
223 224 225
For-2018 (IES,GATE & PSUs) Page 91 of 213 Rev.0
St i
Strainrateeffects
t ff t GATE 2015
GATE-2015
GATE2006
y Strainrateeffect(hotWorking) The ultimate tensile strength of a material is 400
The strain hardening exponent n of stainless
o = C m
MPa and the elongation up to maximum load is
35%.
% If the
h materiali l obeys
b power law
l off hardening,
h d i steall SS 304 with
h distinct
d yield
ld and
d UTS values
l
1 dh v Platen Velocity then the true stresstrue strain relation (stress in
= = = undergoing plastic deformation is
h dt h Instantaneous height MPa) in the plastic deformation range is:
(a) = 540 0.30 (b) = 775 0.30
0 30 a) n<0
(c) = 540 0.35 (d) = 775 0.35 b)n=0
c) 0<n<1
d)n=1
GATE2012SameQGATE2012(PI) GATE2016(PI)
GATE2017 Asolidcylinderofdiameter100mmandheight50mm Two solid cylinders of equal diameter have different
The Poisson
Poissonss ratio for a perfectly isforgedbetweentwofrictionlessflatdiestoaheightof
f db f l fl d h h f
incompressible linear elastic material is heights. They are compressed plastically by a pair of rigid
25mm Thepercentagechangeindiameteris
25mm.Thepercentagechangeindiameteris dies to create the same percentage reduction in their
(a) 1 (b) 0.5
( )0
(c) (d) Infinite
I fi it (a)0 (b)2 07
(b)2.07 (c)20 7
(c)20.7 (d)41 4
(d)41.4 respecti e heights.
respective heights Consider that the dieworkpiece
die orkpiece
interface friction is negligible.
negligible The ratio of the final
diameter of the shorter cylinder
y to that of the longer
g
cylinder is __________.
BySKMondal
232 233 234
For-2018 (IES,GATE & PSUs) Page 92 of 213 Rev.0
Extrusion y Steels, stainless steels, and nickelbased alloys are
y The extrusion process is like squeezing toothpaste out of
y Metal is compressed and forced to flow through a difficult to extrude. (high yield strengths, welding with
a tube.
suitably
bl shaped
h d die
d to form
f a product
d with
h reduced
d d but
b wall). Use phosphatebased and molten glass
constant cross section.
section lubricants .
y Metal will undergo triaxial compression.
compression
AdvantagesofExtrusion
d f IES 2012 IES 2009
y Any crosssectional shape can be extruded from the Extrusion
E i process can effectively
ff i l reduce
d the
h cost off Which
Whi h one off the
h following
f ll i statements is i correct??
product through ((a)) In extrusion p
process,, thicker walls can be obtained
nonferrous
f metals.
t l
(a) Material saving by increasing the forming pressure
y Many shapes (than rolling) (b) process time saving (b) Extrusion is an ideal process for obtaining rods from
y No
oddraft
at (c) Saving in tooling cost metal having poor density
(d) saving in administrative cost (c) As compared to roll forming, extruding speed is high
y Huge reduction in cross section.
(d) Impact extrusion is quite similar to Hooker
Hooker'ss process
y Conversion from one product to another requires only a including the flow of metal being in the same direction
single die change
Cold Impact
Hydrostatic Extrusion Extrusion
Forging
y Design
D i off die
di is
i a problem.
bl
IndirectExtrusion
d Contd IES 2012 IES 2007
Which
Whi h off the h following
f ll i are correct for
f an indirect
i di hot
h Assertion
A i (A):
(A) Greater
G force
f on the
h plunger
l is
i required
i d
y Required force is lower (25 to 30% less)
extrusion process? in case of direct extrusion than indirect one.
y Low process waste. 1. Billet remains stationary Reason (R): In case of direct extrusion, the direction of
the force applied
pp on the p plunger
g and the direction of
2 There is no friction force between billet and container
2.
the movement of the extruded metal are the same.
walls.
(a) Both A and R are individually true and R is the correct
3. The force required on the punch is more in explanation of A
comparison
co pa so to d direct
ect eextrusion.
t us o . (b) Both
B th A and d R are individually
i di id ll true
t b t R is
but i nott the
th
4. Extrusion parts have to be provided a support. correct explanation of A
( ) 1, 2, 3 and
(a) d4 (b) 1, 2 and
d 3 only
l (c) A is true but R is false
(c) 1, 2 and 4 only (d) 2, 3 and 4 only ((d)) A is false but R is true
256 257 258
IES2016
IAS 2004 Statement (I): Employing the extrusion process is not ColdExtrusion
ld
Assertion
A i (A):
(A) Indirect
I di extrusion
i operation
i can be
b economical in case of large billets.
billets
y Used with lowstrength metals such as lead, tin, zinc,
performed either by moving ram or by moving the Statement (II): A significant part of the press capacity is lost
container. overcoming
i f i i
frictional
l resistance
i b
between workpiece
k i and
d and
d aluminum
l to produce
d collapsible
ll bl tubes
b f
for
cylinder wall during the extrusion process.
Reason (R): Advantage in indirect extrusion is less toothpaste medications,
toothpaste, medications and other creams; small "cans"
cans
(a) Both Statement (I) and Statement (II) are individually true and
quantity of scrap compared to direct extrusion.
Statement ((II)) is the correct explanation
p of Statement ((I).
) for shielding electronic components and larger cans for
( ) Both
(a) h A and d R are individually
d d ll true and d R is the
h
(b) Both Statement (I) and Statement (II) are individually true but
correct explanation of A food and beverages.
St t
Statementt (II) is
i nott the
th correctt explanation
l ti off Statement
St t t (I).
(I)
(b) Both A and R are individually true but R is not the
(c) Statement (I) is true but Statement (II) is false. y Nowadays also been used for forming mild steel parts.
correct explanation of A
(d) Statement (I) is false but Statement (II) is true
(c) A is true but R is false
(d) A is false but R is true
259 260 261
For-2018 (IES,GATE & PSUs) Page 95 of 213 Rev.0
Backwardcoldextrusion
k d ld ImpactExtrusion IES 2008,GATE1989(PI)
y The metal is extruded through the gap between the Which one of the following methods is used for the
punch
h and
d die
d opposite to the
h punch
h movement. manufacture
f off collapsible
ll bl toothpaste
h tubes?
b
y For
F softer
f materials
i l such
h as aluminium
l i i and
d its
i alloys.
ll ( ) Impact
(a) I extrusion
i (b) Di
Direct extrusion
i
y Used
U d for
f making
ki collapsible
ll ibl tubes,
t b cans for
f liquids
li id and
d ( ) Deep
(c) D d
drawing
i (d) Pi i
Piercing
similar articles.
articles
HookerMethod
k h d HydrostaticExtrusion
d HydrostaticExtrusion
d Contd.
y The
Th ram/punch
/ h has
h a shoulder
h ld and d acts
t as a mandrel.
d l
y Another type of cold extrusion process.
y A flat blank of specified diameter and thickness is placed in a
suitable
i bl die
di and d is
i forced
f d through
h h the
h opening
i off the
h die
di with
ih y Highpressure fluid applies the force to the workpiece
the punch
y when
h the
h punch h starts downward
d d movement. Pressure
P i
is through
h h a die.
di
exerted by the shoulder of the punch, the metal being forced
t flow
to fl th
through h the
th restricted
t i t d annular
l space between
b t th
the y It i forward
is f d extrusion,
t i b t the
but th fluid
fl id pressure
punch and the opening in the bottom of the die.
y I place
In l off a flat
fl solid
lid blank,
bl k a hollow
h ll slug
l can also
l beb used.
d surrounding the billet prevents upsetting.
upsetting
y If the tube sticks to the punch on its upward stroke, a y Billet
Billetchamber
chamber friction is eliminated, and the
stripper willll strip it from
f the
h punch.h
y Small copper tubes and cartridge cases are extruded by this pressurized fluid acts as a lubricant between the billet
method.
268 and the die. 269 270
For-2018 (IES,GATE & PSUs) Page 96 of 213 Rev.0
HydrostaticExtrusion
d Contd. IAS 2000
y Temperature
T is
i limited
li i d since
i the
h fluid
fl id acts as a heat
h sink
i k Application Assertion
A i (A):
(A) Brittle
B i l materials i l such h as grey cast
and the common fluids (light hydrocarbons and oils) iron cannot be extruded by hydrostatic extrusion.
burn or decomposes at moderately low temperatures. y Extrusionofnuclearreactorfuelrod
E t i f l t f l d
Reason(R): In hydrostatic extrusion, billet is
y The metal deformation is performed in a high high y Claddingofmetals uniformly compressed from all sides by the liquid. liquid
compression environment. Crack formation is (a) Both A and R are individually true and R is the
suppressed leading to a phenomenon known
suppressed, kno n as y Makingwiresforlessductilematerials correct explanation
l off A
pressureinduced ductility. (b) Both
ot A aand d R aaree individually
d v dua y ttrue
ue but R iss not
ot tthee
y Relatively brittle materials like cast iron, stainless steel, correct explanation of A
molybdenum, tungsten and various inter intermetallic
metallic ( ) A is
(c) i true
t b t R is
but i false
f l
compounds can be plastically deformed without
fracture and materials with limited ductility become
fracture, (d) A is false but R is true
highly plastic. 271 272 273
ForIESOnly
LubricationforExtrusion
b f IES2009Conventional
y For
F hot
h extrusion
i glass
l is
i an excellent
ll lubricant
l bi with
ih Explain the processes of extrusion given below.
ProcessvariablesinExtrusion
Process variables in Extrusion
steels, stainless steels and high temperature metals and 1. Experimental
p studies of flow
alloys. Indicate one typical product made through each of these 2. Temperature and Metallurgy: Variations in temperature
y For cold extrusion,
extrusion lubrication is critical,
critical especially with processes:
during extrusion seem to influence flow behaviour in
steels, because of the possibility of sticking (seizure) number of ways. As indicated, flow patterns may be
changed
g considerablyy byy rendering g the temperature
p
bet een the workpiece
between orkpiece and the tooling if the lubrication (i) Direct
Di t Extrusion
E t i
distribution in the container. It is known that the extrusion
breaks down. Most effective lubricant is a phosphate pressure mayy be lowered if either the temperature
p p of the
conversion coating on the h workpiece.
k (ii) Indirect Extrusion
billet or the velocity of the stem is increased, and that there
are certain limitations, because the material starts melting g
(iii) Hydrostatic Extrusion
or cracking if it is leaves the die with too high temperature.
(iv) Impact Extrusion
277 278 279
For-2018 (IES,GATE & PSUs) Page 97 of 213 Rev.0
ForIESOnly ForIESOnly
IES
IES 2014 Extrusion Defects
ExtrusionDefects IES 2016
IES2016
StatementI: For high extrusion pressure, the initial
y Surface crack due to high
g temperature,
p g speed,
high p Surface cracking occurring at low temperature in
temperature of billet should be high. high
high friction etc.
StatementII: As the speed of hot extrusion is hydrostatic extrusion is know as
i
increased,
d it may lead l d to t melting
lti off alloy
ll y Bamboo defects at low temperature due to sticking of
constituents metals in die land. (a)FluidDefect (b)BambooDefect
(a) Both Statement (I) and Statement (II) are y Pipe defects or tail pipe or fishtailing, during
(c)Fishtailing (d)ArrowheadFracture
individuallyy true and Statement (II) is the correct extrusion surface oxides and impurities p are driven
explanation of Statement (I) towards the centre of the billet, like funnel called pipe.
(b) Both Statement (I) and Statement (II) are y Centre Burst or Chevron defect are attributed to a
individually true but Statement (II) is not the correct state of hydrostatic tensile stress at the centreline in the
explanation of Statement (I)
d f
deformation
i zone in
i the
h die.
di Tendency
T d i
increases with
ih
(c) Statement (I) is true but Statement (II) is false increasing die angle and amount of impurities. Tendency
(d) Statement
St t t (I) is
i false
f l but
b t Statement
St t t (II) is
i true
t decrease with increasing extrusion ratio and friction.
280 281 282
GATE2014
With respect to metal working,
working match Group A with Group B
JWM2010 GroupA GroupB
WireDrawing
Assertion (A) : Extrusion speed depends on work P:Defectinextrusion I:alligatoring y A cold working process to obtain wires from rods of
material.
Q:Defectinrolling II:scab
Reason (R) : High extrusion speed causes cracks in b
bigger d
diameters through
h h a die.
d
R:Productofskew III:fishtail
the material. rolling
lli y Same
S process as bar
b drawing
d i except that
h iti involves
i l
(a) Both A and R are individually true and R is the S:Productofrolling IV:seamlesstube
correctt explanation
l ti off A smallerdiameter material.
material
throughclustermill
(b) Both A and R are individuallyy true but R is not the V:thinsheetwithtighttolerance y At the start of wire drawing, the end of the rod or wire to
correct explanation of A VI:semifinishedballsofballbearing be drawn is pointed to make for an easier entrance of
(c) A is true but R is false wire into the die. This pointing is done by means of
P Q R S P Q R S rotary swaging or by simple hammering.
(d) A is false but R is true (a) II III VI V (b) III I VI V
283
(c) III I IV VI (d) I II V VI
284 285
IES2016
Statement (I) : In wiredrawing, the end of the stock CleaningandLubricationinwireDrawing IES2010
is made pointed
pointed to make for easier entrance of the y Cleaningisdonetoremovescaleandrustbyacidpickling.
Cleaningisdonetoremovescaleandrustbyacidpickling Assertion (A): Pickling and washing of rolled rods
wire into the die. y Lubrication boxes precede the individual dies to help reduce is carried out before wire drawing.
Statement (II) : The pointing of the wire is done friction drag and prevent wear of the dies. Reason (R): They lubricate the surface to reduce
exclusivelyy by
y rotaryy swaging
g g and not by y simple
p friction while drawing g wires.
hammering. y Sulling: The wire is coated with a thin coat of ferrous
(a) Both A and R are individually true and R is the
(a) Both Statement (I) and Statement (II) are individually true and hydroxide which when combined with lime acts as filler for correctt explanation
l ti off A
Statement (II) is the correct explanation of Statement (I). the lubricant. (b) Both A and R are individuallyy true but R is NOT the
(b)BothStatement(I)andStatement(II)areindividuallytruebut y Phosphating: A thin film of Mn, Fe or Zn phosphate is correct explanation of A
( ) p ()
Statement(II)isnotthecorrectexplanationofStatement(I). applied on the wire.
wire (c) A is true but R is false
(c)Statement(I)istruebutStatement(II)isfalse. (d) A is false but R is true
y Electrolytic
y coating:
g For veryy thin wires,, electrolytic
y coating
g
(d)Statement(I)isfalsebutStatement(II)istrue
292
of copper is used to reduce friction. 293 294
IES
IES 2014
StatementI: In drawing process, crosssection of WireDrawingDie
BundleDrawing
Bundle Drawing round d wire
i is
i reduced
d d by
b pulling
lli it through
th h a die
di
StatementII: Bundle drawing g p
produces wires that
In this process,
process many wires (as much as several
are polygonal in crosssection rather than round
thousand)) are drawn simultaneouslyy as a bundle. To (a) Both Statement (I) and Statement (II) are
prevent sticking, the wires are separated from each individually true and Statement (II) is the correct
explanation
l i off Statement
S (I)
other by a suitable material. The crosssection of the
((b)) Both Statement ((I)) and Statement ((II)) are
wires is somewhat
h polygonal.
l l individually true but Statement (II) is not the correct
explanation of Statement (I)
(c) Statement (I) is true but Statement (II) is false
(d) Statement (I) is false but Statement (II) is true y Die materials: tool steels or tungsten carbides or
298 299 polycrystalline diamond (for fine wire) 300
RodandTubeDrawing
d d b RodandTubeDrawing
d d b Contd
y Rod
R d drawing
d i isi similar
i il to wire
i drawing
d i except for
f the
h fact
f
that the dies are bigger because of the rod size being
larger than the wire.
y The tubes are also first pointed and then entered
through the die where the point is gripped in a similar
way
a as the bar drawing
dra ing and pulled through in the form TubeSinking FixedPlugDrawing
desired along a straight line.
y When the final size is obtained, the tube may be
annealed and straightened.
y The practice of drawing tubes without the help of an Back
i t
internall mandrel
d l is
i called
ll d tube
t b sinking.
i ki
301 302 FloatingplugDrawing MovingMandrel 303
Swagingorkneading
k d
IES1993;GATE1994(PI),2014(PI)
IES 1993; GATE 1994(PI) 2014(PI) IAS2006 y The hammering of a rod or tube to reduce its diameter
A moving mandrel is used in Which one of the following processes necessarily where
h the
h die
d itself
lf acts as the
h hammer.
h
(a) Wire drawing (b) Tube drawing requires
q mandrel of requisite
q diameter to form the
y Repeated
R d blows
bl are delivered
d li d from
f various
i angles,
l
((c)) Metal Cutting
g ((d)) Forging
g g internal hole?
causing the metal to flow inward and assume the shape
(a) Hydrostatic Extrusion
of the die.
(b) Tube drawing
y It is cold working.
g The term swaging
g g is also applied
pp to
(c) Swaging
processes where material is forced into a confining die to
(d) Wire
Wi Drawing
D i
304 305
reduce its diameter. 306
For-2018 (IES,GATE & PSUs) Page 100 of 213 Rev.0
Swagingorkneading
k d Contd IES2015 IES 1993
Tandem
T d drawing
d i off wires
i andd tubes
b is i necessary
Rotary swaging is a process for shaping
because
a) Round bars and tubes (a) It is not possible to reduce at one stage
b)Billets
b)Bill (b) Annealing is needed between stages
(c) Accuracy in dimensions is not possible otherwise
c) Dies
(d) Surface finish improves after every drawing stage
d)Rectangular
) g blocks
IES 2011
IES2011 IAS1994
g
MatchListIwithListIIandselectthecorrectanswerusing
thecodegivenbelowthelists: SeamlesstubeManufacturing
Seamless tube Manufacturing Which of the following methods can be used for
manufacturing 2 meter long seamless metallic
List I
ListI List II
ListII 1 Rolling
1.Rolling tubes?
b
A Connectingrods
A.Connectingrods 1 Welding
1.Welding 2Extrusion 1. Drawing g 2. Extrusion
3. Rolling 4. Spinning
B.Pressurevessels 2.Extrusion 3
3.TubeDrawing
g
Select
l the
h correct answer using the
h codes
d given below
b l
C.Machinetoolbeds 3.Forming 4.Spinning Codes:
D.Collapsibletubes 4.Casting (a) 1 and 3 (b) 2 and 3
Codes
A B C D A B C D ( ) 1, 3 and 4
(c) ( ) 2, 3 and 4
(d)
(a) 2 1 4 3 (b) 3 1 4 2
(c) 2 4 1 3 (d) 3 4 1 2319 320 321
A d2 d d o2 P A d A d 2f d
P = Ao o ln o = 2 o o ln o = o ln ( R ) E = = o ln o = 2 o ln o = o ln ( R ) P = Af o ln o = 2 o ln o
A 4 4 A A 4 d
f df A0 f df f f
y For real conditions y For real conditions Drawing Stress
A d
2 d P A d A d
P = KAo ln o = 2 o
K ln o E = = K ln o = 2 K ln o d =
P
= o ln o
A 4
A = 2 o ln o
f df A0 Af df Af f df
K = extrusion
t i constant.
t t K = extrusion
t i constant.
t t
322 323 324
For-2018 (IES,GATE & PSUs) Page 102 of 213 Rev.0
GATE2003 GATE 2009(PI) GATE2006
A brass billet is to be extruded from its initial Using direct extrusion process, a round billet of 100 In a wire drawing operation, diameter of a steel wire
d
diameter off 100 mm to a final
f l diameter
d off 50 mm. mm length
l h and
d 50 mm diameter
d is extruded.
d d is reduced
d d from
f 10 mm to 8 mm. The
h mean flow
fl
The working temperature of 700C
700 C and the Considering an ideal deformation process (no stress of the material is 400 MPa.
MPa The ideal force
extrusion constant is 250 MPa. The force required friction and no redundant work), extrusion ratio 4, required for drawing (ignoring friction and
for extrusion is and average flow stress of material 300 MPa, the redundant work) is
(a) 5.44 MN (b) 2.72 MN pressure (in MPa) on the ram will be (a) 4.48 kN (b) 8.97 kN
(c) 1.36 MN (d) 0.36 MN (a) 416 (b) 624 (c) 700 (d) 832 (c) 20.11 kN (d) 31.41 kN
IFS 2016
IFS2016 G
GATE 20 ( ) C S
2011(PI)CommonDataS1
IES 2011Conventional
A 12.5 mm diameter
d rod
d is to be
b reduced
d d to 10 mm A round rod of annealed brass 7030 is being In a multi pass drawing operation,
multipass operation a round bar of 10 mm
diameter by drawing in a single pass at a speed of 100 diameter and 100 mm length is reduced in crosssection
drawn from a diameter of 6 mm to 3 mm at a b drawing
by d i it successively
i l through
th h a series
i off seven dies
di
m/min. Assuming a semi die angle of 5o and coefficient
of friction between the die and steel rod as 0.15, speed
p of 0.6 m/s. Assume that the frictional and of decreasing exit diameter. During each of these
calculate: d
drawing operations, the
h reduction
d in crosssectionall area
((i)) The p
power required
q in drawing
g redundant work together constitutes 35% of the is 35
35%. The yyield strength
g of the material is 200 MPa.
(ii) Maximum possible reduction in diameter of the rod Ignore strain hardening.
ideal work of deformation.
(iii) If the rod is subjected to a back pressure of 50 The total true strain applied and the final length (in
N/mm2 , what would be the draw stress and maximum Calculate (i) power required in this operation and mm), respectively, are
possible
ibl reduction
d ti ? (a) 2.45 and 8 17 (b) 2.45 and 345
Take stress of the work material as 400 N/mm2 . (ii) die pressure at the exit of the die. [10Marks]
(c) 3.02 and 2043 (d) 3.02 and 3330
[15Marks] Hint: K =895 MPa and n = 0.49
337 338 339
G
GATE 20 ( ) C S2
2011(PI)CommonDataS2 GATE 2014 IAS 1997
In a multi pass drawing operation,
multipass operation a round bar of 10 mm Extrusion
E i force
f DOES NOT depend
d d upon the
h
diameter and 100 mm length is reduced in crosssection A metal rod of initial length is subjected to a
((a)) Extrusion ratio
b drawing
by d i it successively
i l through
th h a series
i off seven dies
di d
drawing process. The
h length
l h off the
h rod
d at any
of decreasing exit diameter. During each of these (b) Type of extrusion process
d
drawing operations, the
h reduction
d in crosssectionall area expression L(t) = Lo(1 + t2)
instant is given by the expression, ( ) Material
(c) M i l off the
h die
di
is 35
35%. The yyield strength
g of the material is 200 MPa. where t is the time in minutes. The true strain rate ((d)) Workingg temperature
p
Ignore strain hardening.
at the end of one minute is ..
Neglectingfrictionandredundantwork theforce(in
Neglectingfrictionandredundantwork,theforce(in
kN)requiredfordrawingthebarthroughthefirstdie,is
(a)15.71 (b)10.21
(c)6.77 (d)4.39
340 341 342
For-2018 (IES,GATE & PSUs) Page 104 of 213 Rev.0
IES 2012 TheDegreeofDrawingorReductionfactor IAS 2006
Write
W i theh process variables
i bl in
i wire
i drawing.
d i inCrossSectionalarea
in Cross Sectional area In
I drawing
d i operationi if Di = initial
i i i l diameter
di and
d Do
Ans. = Outgoing diameter, then what is the degree of
1. Reduction in cross sectional area
drawing equal to?
2. Die
Di anglel Ao Af Do2 D 2f Di Do Do Di Di2 Do2 Di2 Do2
D= = (a) (b) (c ) (d )
33. Friction Ao Do2 Di Do Di2 Di2
A 1
ThereforeTrue strain ( ) = ln o = ln
A 1 D
f
Piercing(Punching)andBlanking
( h ) d l k
SheetMetal
y Product has light weight and versatile shape as y Piercing and blanking are shearing operations.
compared to forging/casting
y In blanking, the piece being punched out becomes
SheetMetalOperation y Most commonly used
strength, formability)
low carbon steel sheet (cost,
the
h workpiece
k i and
d any major
j burrs
b or undesirable
d i bl
y Aluminium and titanium for aircraft and aerospace features should be left on the remaining strip.
strip
y Sheet metal has become a significant material for,
y In piercing (Punching),
(Punching) the punch
punchout
out is the scrap
automotive bodies and frames,
office furniture and the remaining
g strip
p is the workpiece.
p
frames for home appliances
BySKMondal
y y Both done on some form of mechanical press.
Piercing(Punching)andBlanking
Clearance (VIMP)
Clearance(VIMP)
y Die opening must be larger than punch and known as
clearance.
clearance
y Punching
Punch = size of hole
Die = punch size +2 clearance
y Remember: In punching punch is correct size.
y Blanking
Di = size
Die i off product
d
Punch = Die size 2 clearance
y Remember: In blanking die size will be correct.
y Note: In pu
punching
c g cclearance
ea a ce iss p
provided
ov ded o
on Die
e
349 350
In Blanking clearance is provided on punch 351
For-2018 (IES,GATE & PSUs) Page 105 of 213 Rev.0
Clearance
ClearanceContd
Contd.
Example
l GATE2003 PunchingForceandBlankingForce
h d l k
Determine
D i the
h die
di andd punchh sizes
i for
f blanking
bl ki a circular
i l
Fm ax = Lt
A metal disc of 20 mm diameter is to be punched
disc of 20mm diameter from a sheet whose thickness is 1.5
mm. f
from a sheet
h off 2 mm thickness.
h k The
h punch
h and
d the
h
die clearance is 3%.
3% The required punch diameter is
Shear strength of sheet material = 294 MPa
(a) 19.88
19 88 mm (b) 19 94 mm
19.94
Also determine the die and punch sizes for punching a Thepunchingforceforholeswhicharesmallerthanthestock
(c) 20.06
20 06 mm (d) 20 12 mm
20.12 thi k
thicknessmaybeestimatedasfollows:
b ti t d f ll
circular hole of 20mm diameter from a sheet whose
thickness is 1.5 mm. dt
Fmax =
3
d
355 356 t 357
CapacityofPressforPunchingandBlanking Example
l
Estimate the blanking force to cut a blank 25 mm wide
GATE2014
A rectangular hole of size 100 mm 50 mm is to be
Presscapacitywillbe= Fmax C and
d 30 mm long
l f
from a 1.5 mm thick
h k metall strip, iff the
ultimate shear strength of the material is 450 N/mm2.
h
made on a 5 mm thick sheet of steel having
ultimate tensile strength and shear strength of 500
MPa and 300 MPa, respectively. The hole is made
Also determine the work done if the percentage
b punching
by hi process. Neglecting
N l i the
h effect
ff off
[WhereCisaconstantandequalto1.1to1.75depending penetration is 25 percent of material thickness. clearance, the punching force (in kN) is
upontheprofile]
th fil ]
(a) 300 (b) 450
(c) 600 (d) 750
be equal to: Where C is a constant and equal to 1.1 to 1.75 depending upon the profile total work done remains same.
1 EN
1 A
Actual
l power in W)=
i press ( P iinW
(a) (b) 2 60
4
WhereE is actual energy and is efficiency of the press
(c) 1 (d) 2
367 368 369
For-2018 (IES,GATE & PSUs) Page 107 of 213 Rev.0
Force required with shear on Punch
ForcerequiredwithshearonPunch
Example
F ptt [for
[f circular
i l hole
h l and
d other
h searing
i
F = max y A hole, 100 mm diameter, is to be punched in steel plate
S + pt operations]
5.6 mm thick. The ultimate shear stress is 550 N/mm2 .
Example
l GATE2010StatementLinked1 GATE2010StatementLinked2
A washer
h with
i h a 12.7 mm internal
i l hole
h l and d an outside
id Statement
S for
f Linked
Li k d Answer
A Questions:
Q i Statement for Linked Answer Questions:
diameter of 25.4 mm is to be made from 1.5 mm thick In a shear cutting operation, a sheet of 5 mm thickness In a shear cutting operation, a sheet of 5mm thickness
strip. The
h ultimate
l shearing
h strengthh off the
h materiall off is cut along a length of 200 mm.
mm The cutting blade is 400
is cut along a length of 200 mm. The cutting blade is 400 mm long and zeroshear (S = 0) is provided on the edge.
the washer is 280 N/mm2. mm long g and zeroshear ((S = 0)) is p
provided on the edge.
g The ultimate shear strength
g of the sheet is 100 MPa and
(a) Find the total cutting force if both punches act at The ultimate shear strength of the sheet is 100 MPa and penetration to thickness ratio is 0.2. Neglect friction.
the same time and no shear is applied
pp to either p
punch penetration to thickness ratio is 0.2. Neglect
p g friction. 400
400
or the die.
(b) What will be the cutting force if the punches are
staggered, so that only one punch acts at a time. S
S
( ) Taking
(c) T ki 6 % penetration
60% i andd shear
h on punchh off 1 Assuming force vs displacement curve to be rectangular, A shear of 20 mm (S = 20 mm) is now provided on the
mm, what will be the cutting force if both punches act the work done ((in J) is blade. Assuming g force vs displacement curve to be
together.
h trapezoidal,
d l the
h maximum force
f ( kN)
(in k ) exerted
d is
(a) 100 (b) 200 (c) 250 (d) 300
373 374 (a) 5 (b) 10 (c) 20 (d) 40 375
FineBlanking
l k y Slitting moving rollers trace out complex paths during y Trimming Cutting unwanted excess material from the
Fine
Fi Blanking
Bl ki dies
di are designed
d i d that
h have
h small
ll periphery of a previously formed component.
clearances and pressure pads that hold the material cutting (like a can opener).
while it is sheared. The final result is blanks that have y Shaving
h Accurate dimensions
d off the
h part are obtained
b d by
b
y Perforating: Multiple holes which are very small and
extremelyy close tolerances. removing a thin strip of metal along the edges.
edges
close together are cut in flat work material.
Elasticrecoveryorspringback
l b k Elasticrecoveryorspringback
l b k Contd.. IAS 2003
y Total deformation = elastic deformation + plastic y More important in cold working. The
Th 'spring
' i back'
b k' effect
ff in
i press working
ki is i
((a)) Elastic recoveryy of the sheet metal after removal of
d f
deformation. the load
y It depends
d d on the
th yield
i ld strength.
t th Higher
Hi h the
th yield
i ld (b) Regaining the original shape of the sheet metal
strength, greater spring back. (c) Release of stored energy in the sheet metal
y At the
th end
d off a metal
t l working
ki operation,
ti when
h th
the
(d) Partial recovery of the sheet metal
pressure is released,
released there is an elastic recovery and the
total deformation will g
get reduced a little. This y To compensate this, the cold deformation be carried
phenomenon is called as "spring back". beyond the desired limit by an amount equal to the
spring back.
382 383 384
(d) None
N off these
h
y Attached to the press bed and the die shoe is then small punches.
p
attached to it.
Pitman Dowelpin
l GATE2011
y It is a connecting rod which is used to transmit motion The shear strength of a sheet metal is 300 MPa. The
blanking g force required
q to p
produce a blank of 100
f
from the
h main drive
d shaft
h f to the
h press slide.
ld mm diameter from a 1.5 mm thick sheet is close to
(a) 45 kN
(b) 70 kN
(c) 141 kN
(d) 3500 kN
(a) 291 (b) 301 (c) 311 (d) 321 (b) 3.29
(c) 5.03
(d) 6.33
397 398 399
GATE2002
GATE
GATE 2012 GATE2008(PI) In
I a blanking
bl ki operation,
i the
h clearance
l is
i provided
id d
Calculate the p punch size in mm,, for a circular on
A blank of 50 mm diameter is to be sheared from a
blanking operation for which details are given (a) The die
below. sheet of 2.5 mm thickness. The required radial
(b) Both the die and the punch equally
Size of the blank 25 mm clearance between the die and the punch is 6% of
(c) The punch
Thi k
Thickness off the
th sheet
h t 2 mm sheet thickness. The punch and die diameters (in mm) (d) Brittle the punch nor the die
Radial clearance between punch and die 0.06 mm for this blanking operation,
operation respectively,
respectively are
Die allowance 0.05 mm
(a) 24.83
24 83 (b) 24.89
24 89 (a) 50.00 and 50.30 (b) 50.00 and 50.15
(c) 25.01 (d) 25.17 (c) 49.70 and 50.00 (d) 49.85 and 50.00
y As a p
punch descends into a mating
g die,, the metal
GATE2003 GATE2017
A shell of 100 mm diameter and 100 mm height with
ISRO2011
A 10 mm deep cylindrical cup with diameter of 15
the
h corner radius
d off 0.4 mm is to be
b produced
d d by
b The initial blank diameter required to form
mm is drawn from a circular blank. Neglecting a cylindrical cup of outside diameter 'd and
cup drawing.
drawing The required blank diameter is totall height
h h 'h' having
h a corner radius
d ' ' is
'r'
the variation in the sheet thickness, the diameter
(a) 118 mm (b) 161 mm obtained using the formula
(up to 2 decimal points accuracy) of the blank is
(c) 224 mm (d) 312 mm (a ) Do = d 2 + 4dh 0.5r
______ mm. (b) Do = d + 2h + 2r
(c) Do = d 2 + 2h 2 + 2r
430 431 (d ) Do = d 2 + 4dh 0.5r 432
For-2018 (IES,GATE & PSUs) Page 114 of 213 Rev.0
y Drawing Force IAS 2013Main
D A cup, of 50 mm diameter and 100 mm height, is to be
P = dt C
d d
drawn f
from l
low carbon
b steell sheet.
h Neglecting
l the
h
y Blank Holding Force
influence of thickness and corner radii:
Blank holding force required depends on the
wrinkling
i kli t d
tendency off the
th cup. The
Th maximum
i (i) Calculate the blank diameter
limit is g
generallyy to be onethird of the drawing
g (ii) Decide whether it can be drawn in a single draw,
draw if
force.
maximum reduction p
permitted is 4
40%.
y Draw
D Cl
Clearance
Punch diameter = Die opening diameter 2.5 25t [10marks]
433 434 435
IFS2013 Deepdrawing
d IES 2008
y Drawing when cup height is more than half the diameter is A cylindrical
li d i l vessell with
i h flat
fl bottom
b can be
b deep
d
A symmetrical cup of circular cross section with
termed deep
p drawing.
g drawn by
d
diameter 40 mm and
d height
h h 60 mm with
h a corner (a) Shallow drawing
y Easy with ductile materials.
radius of 2 mm is to be obtained in C20 steel of 0.6
06 (b) Single action deep drawing
y Due to the radial flow of material, the side walls increase in (c) Double action deep drawing
mm thickness. Calculate the blank size for the
thickness as the height is increased. (d) Triple action deep drawing
drawn cup. Will it be possible to draw the cup in
y A cylindrical vessel with flat bottom can be deep drawn by
single step?
double action deep drawing.
drawing
[10Marks]
y Deep drawing is a combination of drawing and stretching.
436 437 438
DeepDrawability
bl LimitingDrawingRatio(LDR)
StressesonDeepDrawing
Stresses on Deep Drawing y The ratio of the maximum blank diameter to the y Theaveragereductionindeepdrawing
y In flange of blank: d
= 0.5
05
d
diameter off the
h cup drawn
d . i.e. D/d.
d
Biaxial tension and D
compression y There
Th i a limiting
is li i i drawing
d i ratio
i (LDR),
(LDR) after
f which
hi h the
h d
Reduction = 1 100% = 50%
D
punch will pierce a hole in the blank instead of drawing.
drawing Th b rule:
Thumb l
y In wall of the cup:
First draw:Reduction = 50 %
simple uniaxial
uni axial y This ratio depends upon material,
material amount of friction
tension Second draw:Reduction = 30 %
present, etc.
p Third draw:Reduction = 25 %
y Limiting drawing ratio (LDR) is 1.6 to 2.3 Fourth draw:Reduction = 16 %
Fifth draw:Reduction = 13 %
439 440 441
For-2018 (IES,GATE & PSUs) Page 115 of 213 Rev.0
ForIESOnly
Combination
C bi i dies
di
A combination die is same as that of a compound die with
th main
the i difference
diff th t here
that h noncutting
tti operations
ti such
h as
bending and forming are also included as part of the
operation.
operation
445 Back
446 Back
447
ForIESOnly
IAS1996 Lubrication
b IAS 2007
Compound die performs In
I drawing
d i operation,
i proper lubrication
l b i i is
i
y Indrawingoperation,properlubricationisessentialfor
essential for which of the following reasons?
(a) Two or more operations at one station in one stroke 1. Toimprovedielife. 1. To improve die life
(b) Two or more operations at different stations in one 2 To reduce drawing forces
2.
2. Toreducedrawingforces. 3. To reduce temperature
stroke
t k
3. Toreducetemperature. 4. To improve surface finish
(c) high frequency sound wave S l t the
Select th correctt answer using
i the
th code
d given
i b l
below:
4. Toimprovesurfacefinish. (a) 1 and 2 onlyy (b) 1, 3 and 4 onlyy
(d) High frequency eddy current
(c) 3 and 4 only (d) 1, 2, 3 and 4
IES1999 DefectsinDrawing
f missstrike
k DefectsinDrawing
f Orangepeell
y Due
D to the
h misplacement
i l off the
h stock,
k unsymmetrical
i l y A surface
f roughening
h i (defect)
(d f ) encountered
d in
i forming
f i
Considerthefollowingstatements:
flanges may result. This defect is known as miss strike. products from metal stock that has a coarse grain size.
E i inadrawncupcanbeduenonuniform
Earing i d b d if
y It is due to uneven flow or to the appearance of the
1. Speedofthepress
p p overly large grains usually the result of annealing at too
2. Clearancebetweentools high a temperature.
3. Materialproperties
M i l i
4. Blankholding
4 g
Whichofthesestatementsarecorrect?
( ) 1,2and3
(a) d (b) d
(b)2,3and4
((c)1,3and4
) ,3 4 ((d)1,2and4
) , 4
454 455 456
St t h t i (lik L d Lines)
Stretcherstrains(likeLuders Li ) GATE2008
y Caused
C d by
b plastic
l ti deformation
d f ti due
d to
t inhomogeneous
i h Surfacescratches
Surface scratches In
I the
h deep
d drawing
d i off cups, blanks
bl k show
h a tendency
d to
wrinkle up around the periphery (flange).
yielding. y Dieorpunchnothavingasmoothsurface,insufficient
lubrication The most likely cause and remedy of the phenomenon are,
y These lines can crisscross the surface of the workpiece
p and respectively,
p y,
may be visibly objectionable. (A) Buckling due to circumferential compression; Increase
blank holder pressure
y Low carbon steel and aluminium shows more stretcher (B) High blank holder pressure and high friction; Reduce
strains. bl k holder
blank h ld pressure and d apply
l lubricant
l bi t
(C) High temperature causing increase in circumferential
length: Apply coolant to blank
((D)) Buckling g due to circumferential compression;
p ; decrease
blank holder pressure
457 458 459
For-2018 (IES,GATE & PSUs) Page 117 of 213 Rev.0
IAS 1997 GATE1999 GATE2006
Which
Whi h one off the h following
f ll i factor
f promotes the
h Identify
Id if the
h stress state ini the
h FLANCE portion i off a Match
M h the h items
i in
i columns
l I and
d II.
II
tendency for wrinking in the process of drawing? PARTIALLYDRAWN CYLINDRICAL CUP when deep Column I Column II
(a) Increase in the ratio of thickness to blank diameter drawing without a blank holder P. Wrinkling 1. Yield point elongation
of work material (a) Tensile in all three directions Q Orange peel
Q. 2
2. Anisotropy
(b) Decrease in the ratio thickness to blank diameter of (b) No stress in the flange at all, because there is no R. Stretcher strains 3. Large grain size
workk materiall bl k h ld
blankholder S. Earing 4. Insufficient blank holding
(c) Decrease
ec ease in tthee holding
o d g force
o ce o
on tthee b
blank
a (c) Tensile
e s e st
stress
ess in oonee d
direction
ect o aand
d co
compressive
p ess ve in force
(d) Use of solid lubricants the one other direction 5. Fine grain size
(d) Compressive
C i in i two
t di ti
directions and
d tensile
t il ini the
th 6
6. Excessive blank holding force
third direction (a) P 6, Q 3, R 1, S 2 (b) P 4, Q 5, R 6, S 1
(c) P 2, Q 5, R 3, S 4 (d) P 4, Q 3, R 1, S 2
460 461 462
Spinning Spinning
1. A mandrel
d l (or( die
di for
f internal
i l pieces)
i ) is
i placed
l d on a
rotating axis (like a turning center).
y Spinning
S i i i a coldforming
is ld f i operation
ti i which
in hi h a
2. A blank or tube is held to the face of the mandrel.
rotating disk of sheet metal is shaped over a male 3 A roller is pushed against the material near the
3.
form, or mandrel. center of rotation, and slowly moved outwards, pushing
the
h blank
bl k against the h mandrel.
d l
y Localized pressure is applied through a simple 4. Thee pa
partt co
conforms
o s to tthee sshape
ape oof tthee mandrel
a d e ((with
t
roundended wooden or metal tool or small roller, some springback).
5. The
Th process is i stopped,
t d and d the
th partt is i removed d andd
which traverses the entire surface of the part
trimmed.
Underwater
HERF explosions.
U d
UnderwaterExplosions
E l i U d
Underwaterexplosions
l i ElectrohydraulicForming
l h d l
y A shock wave in the fluid medium (normally water ) is y An operation using electric discharge in the form of
sparks to generate a shock wave in a fluid is called
generated
d by
b detonating
d an explosive
l charge.
h
electrohydrulic forming.
y TNT and
d dynamite
d i for
f higher
hi h energy and
d gun powder
d for
f
y A capacitor bank is charged through the charging circuit,
lower energy is used.
used subsequently,
b tl a switch
it h is
i closed,
l d resulting
lti i a spark
in k
y Used for parts of thick materials.
materials within the electrode g
gap
p to discharge
g the capacitors.
p
y Employed in Aerospace, aircraft industries and y Energy level and peak pressure is lower than underwater
explosions but easier and safer.
automobile related components.
y Used for bulging operations in small parts.
475 476 477
For-2018 (IES,GATE & PSUs) Page 119 of 213 Rev.0
ForIESOnly ForIESOnly ForIESOnly
ElectromagneticorMagneticPulseForming
y Based
B d on the
h principle
i i l that
h the
h electromagnetic
l i field
fi ld off
an induced current always opposes the electromagnetic
field of the inducing current.
ForIESOnly
IES2016
Consider the following in case of high energy forming
IES2011 JWM2010
p
processes:
Assertion (A) : In magnetic pulseforming
pulse forming method,
method
1. The evacuation between die and blank in explosive High energy rate forming process used for magnetic field produced by eddy currents is used to
forming forming is done by a vacuum pump.
pump create force
f b
between coil
il and
d workpiece.
k i
forming components from thin metal sheets or
2. The pressure waves produced in water in explosive
Reason ((R)) : It is necessary y for the workpiece
p
f
forming d f
deform the
h blank
bl k to the
h die
d shape.
h d f
deform thin
hi tubes
b is:
i
material to have magnetic properties.
33. The electrohydraulic
y formingg makes use of discharge g of
large amount of electrical energy used in a capacitor bank.
( ) Petroforming
(a) P t f i ( ) Both
(a) B th A and d R are individually
i di id ll true
t and
d R is
i the
th
correct explanation of A
4
4. In Petroforge,
Petroforge the piston is moved by combustion of fuel (b) Magnetic pulse forming
moving at the rate of 150 200 m/s. (b) Both A and R are individually true but R is NOT the
Whi h off the
Which th above
b are correct?
t? (c) Explosive forming correct explanation of A
(a) 1, 2, 3 and 4 (b) 1, 2 and 3 only (c) A is true but R is false
(d) electro
electrohydraulic
hydraulic forming
(c) 3 and 4 only (d) 1, 2 and 4 only (d) A is false but R is true
484 485 486
For-2018 (IES,GATE & PSUs) Page 120 of 213 Rev.0
IES2010 IES 2007 IES 2009
Assertion (A) : In the high energy rate forming
method, the explosive forming has proved to be an
Which one of the following metal forming Which one of the following is a high energy rate
excellent
ll method
h d off utilizing
ili i energy at high
hi h rate and d processes is not a high
h h energy rate forming
f process? forming process?
utilizes both the high explosives and low explosives.
Reason (R): The gas pressure and rate of detonation ( ) Electromechanical
(a) El h i l forming
f i ( ) Roll
(a) R ll forming
f i
can be controlled for both types yp of explosives.
p
(b) Rollforming
R ll f i (b) Electrohydraulic
El t h d li forming
f i
(a) Both A and R are individually true and R is the correct
explanation of A (c) Explosive forming (c) Rotary forging
(b) Both A and R are individually true but R is NOT the
correct explanation of A
(d) Electrohydraulic
Electro hydraulic forming (d) Forward extrusion
(c) A is true but R is false
(d) A is false but R is true 487 488 489
StretchForming
h Contd...... StretchForming
h Contd...... GATE2000
A 1.5 mm thick
hi k sheet
h is
i subject
bj to unequall biaxial
bi i l
stretching and the true strains in the directions of
stretching are 0.05 and 0.09. The final thickness of
the sheet in mm is
(a) 1.414 (b) 1.304
( ) 1.362
(c) (d) 289
Embossing
b Coining Bending
y Afterbasicshearingoperation,wecanbendaparttogiveitsome
shape.
h
y It is a very shallow drawing operation where the depth of y Coining is essentially a coldforging operation except for
y Bendingpartsdependsuponmaterialpropertiesatthelocationof
the
h draw
d is limited
l d to one to three
h times the
h thickness
h k off the
h fact
f that
h the
h flow
fl off the
h metall occurs only
l at the
h top thebend.
h b d
y Atbend,biaxialcompressionandbiaxialtensionisthere.
the metal,
metal and the material thickness remains largely layers and not the entire volume.
volume
unchanged. y Coining is used for making coins,
coins medals and similar
articles.
ForIESOnly
=bendangle(
g (inradian) ForUorchannelbendingforcerequiredisdoublethanV bending
ForUorchannelbendingforcerequiredisdoublethanV
ForedgebendingitwillbeaboutonehalfthatforV bending
502 503 504
For-2018 (IES,GATE & PSUs) Page 122 of 213 Rev.0
IES 1998
IES1998 Example
l GATE2005
The bending force required for Vbending, U y Calculate the bending force for a 45o bend in aluminium A 2 mm thick
hi k metall sheet
h is
i to be
b bent
b at an angle
l off
blank. Blank thickness, 1.6 mm, bend length = 1200 mm, one radian with a bend radius of 100 mm. If the
b di and
bending d Edge
Ed bending
b di will
ill be
b in
i the
th ratio
ti Di opening
Die i = 8t, UTS = 455 MPa,
MP DieDi opening
i factor
f = stretch factor is 0.5, the bend allowance is
of 1.33 (a) 99 mm (b) 100 mm
(c) 101 mm (d) 102 mm
(a) 1 : 2 : 0.5 (b) 2: 1 : 0.5
2mm
((c)) 1: 2 : 1 ((d)) 1: 1 : 1
1 radian
ForIESOnly
Spanking
k GATE2007
Match
M t h the
th correctt combination
bi ti for
f following
f ll i metal
t l
y During bending, the area of the sheet under the punch
working processes.
h a tendency
has d to flow
fl and
d form
f a bulge
b l on the
h outer Processes Associated state of stress
surface.
surface P. Blankingg 1. Tension
Q. Stretch Forming 2. Compression
y The lower die should be provided with mating surfaces,
surfaces R Coining
R. 3
3. Shear
so that when the p
punch and die are completely
p y closed on S. Deep Drawing 4. Tension and Compression
5. Tension and Shear
the blank, any bulging developed earlier will be
Codes:P Q R S P Q R S
completely presses or spanked out. (a) 2 1 3 4 (b) 3 4 1 5
( ) 5
(c) 4 3 1 (d) 3 1 2 4
508 509 510
Manufacturing of Powder
ManufacturingofPowder
Atomizationusingagasstream IAS 2003
PowderMetallurgy
Powder Metallurgy Assertion
A i (A):
(A) Atomization
A i i method
h d for
f production
d i off
Molten metal is metal powders consists of mechanical disintegration of
y Powder metallurgy is the name given to the f
forcedd through
th h a molten
l stream into fine
f particles.
l
small orifice and
process byy which fine p
p powdered materials are Reason ((R): ) Atomization method is an excellent means
is disintegrated by
a jet of
of making powders from high temperature metals.
blended, pressed into a desired shape
compressed air, air (a) Both A and R are individually true and R is the correct
(compacted), and then heated (sintered) in a inert gas or water explanation of A
jet It is used for
jet,. (b) Both
B th A and d R are individually
i di id ll true
t b t R is
but i nott the
th
controlled
ll d atmosphere
h to bond
b d the
h contacting
low melting point correct explanation of A
surfaces of the particles and establish the desired materials brass,
materials, brass
bronze, Zn, Tn, (c) A is true but R is false
p p
properties. Al, Pb etc. ((d)) A is false but R is true
517 518 519
IES2016
IAS 2007 Statement (I) : Metal powders can be produced by IES 1999
Assertion
A ti (A):
(A) Mechanical
M h i l disintegration
di i t ti off a atomization process.
process Assertion
A i (A):
(A) In
I atomization
i i process off manufacture
f off
molten metal stream into fine particles by means of Statement (II) : In case of metals with low melting metal powder, the molten metal is forced through a
a jet
j t off compressed d air
i is
i known
k as atomization.
t i ti point, the size of particles cannot be controlled and smallll orifice
f andd broken
b k up by b a stream off compressedd
Reason (R): In atomization process inertgas or the shapep of the p particles remains regular
g in air.
water cannot be used as a substitute for compressed atomization. Reason (R): The metallic powder obtained by
air. atomization p process is q
quite resistant to oxidation.
(a) Both Statement (I) and Statement (II) are individually true and
(a) Both A and R are individually true and R is the (a) Both A and R are individually true and R is the correct
Statement (II) is the correct explanation of Statement (I).
correct
co ect eexplanation
p a at o oof A explanation of A
(b) Both Statement (I) and Statement (II) are individually true but
(b) Both A and R are individually true but R is not the (b) Both A and R are individually true but R is not the
correct explanation of A Statement ((II)) is not the correct explanation
p of Statement ((I).
)
correct explanation
l i off A
(c) A is true but R is false (c) Statement (I) is true but Statement (II) is false.
(c) A is true but R is false
( ) A is false but R is true
(d) (d) Statement (I) is false but Statement (II) is true (d) A is false but R is true
520 521 522
For-2018 (IES,GATE & PSUs) Page 124 of 213 Rev.0
GATE 2017(PI)
GATE2017(PI) Manufacturing of Powder
ManufacturingofPowder
Reduction
In powder
d metallurgy,
ll the
h process 'atomization'
' ' GATE2011(PI)
GATE 2011 (PI)
y Metal oxides are turned to pure metal powder when
refers
f to a method
h d off Whi h off
Which th
the f ll i
following powder
d production
d ti
exposed to below melting point gases results in a
methods produces spongy and porous particles?
(a) Producing powders product of cake of sponge metal.
(a) Atomization
(b) compaction of powders y The
h irregular
i l spongelike
lik particles
i l are soft,
f readily
dil
compressible and give compacts of good presinter
compressible, ((b)) Reduction of metal oxides
(c) sintering of powder compacts
(green)
g strength
g ((c)) Electrolytic
y deposition
p
(d) blending of metal powders y Used for iron, Cu, tungsten, molybdenum, Ni and (d) Pulverization
523
Cobalt. 524 525
OnlyforIES
Manufacturing of Powder
ManufacturingofPowder Manufacturing of Powder
ManufacturingofPowder Manufacturing of Powder
ManufacturingofPowder
Electrolytic Deposition
Comminution
C i i y Used for iron, copper, silver
Grinding
g
y Granular
G l material,
t i l which
hi h may be
b coarsely
l atomized
t i d y Process is similar to electroplating.
electroplating
This metallic powder is nothing but the unburnt tiny p
powder,, is fed in a stream of ggas under p
pressure through
g y For making copper powder, copper plates are placed as
chips formed during the process of grinding. a venturi and is cooled and thereby embrittled by the anode in the tank of electrolyte, whereas the aluminium
adiabatic
di b i expansion i off the
h gas before
b f i i i
impinging on a plates
l t are placed
l d in i the
th electrolyte
l t l t to t actt as cathode.
th d
g on which the g
target granules shatters When DC current is p passed, the copper
pp ggets deposited
p
y Process is used for production of very fine powders such on cathode. The cathode plated are taken out and
as are required for injection moulding . Brittle materials powder
d is
i scrappedd off.
ff The
Th powderd isi washed,
h d dried
d i d and d
such as inter
intermetallic
metallic compounds,
compounds ferro
ferroalloys
alloys ferro
ferro pulverized to the desired g
p grain size.
526 chromium, ferrosilicon are produces 527
y The cost of manufacturing is high. 528
Blending
l d Compacting
y Blending
Bl di or mixing
i i operations
ti can be
b done
d either
ith dry
d or wet.
t
y Powder is pressed into a green compact
y Lubricants such as graphite or stearic acid improve the flow
characteristics and compressibility at the expense of reduced y 40 to 1650 MPa pressure (Depends on materials,
H t I t ti Pressing(HIP)
HotIsostatic P i (HIP)
ColdIsostaticPressingg y Is carried out at high
g temperature
p and p
pressure using
ga
gas such as argon.
y The flexible mould is made of sheet metal. (Due to high
temperature)
y Compaction
C i and
d sintering
i i are completed
l d
simultaneously.
simultaneously
yU
Used in the p
production of billets of superalloys,
p y , high
g
speed steels, titanium, ceramics, etc, where the integrity
547
of the materials is a prime consideration 548 549
For-2018 (IES,GATE & PSUs) Page 127 of 213 Rev.0
ForIESOnly ForIESOnly
IAS 1997 S
SprayDeposition
D iti Metal Injection Moulding
MetalInjectionMoulding
Assertion
A ti (A):
(A) Close
Cl dimensional
di i l tolerances
t l are y Spray
S deposition
d iti isi a shapegeneration
h ti process. y Fine metal powders are blended with an organic binder such
NOT possible with isostatic pressing of metal as a polymer or a waxbased binder.
powder
d in i powder
d metallurgy
t ll t h i
technique. y Basic components of a spray deposition process
y The powderpolymer mixture is then injected into split dies,
Reason (R): In the process of isostatic pressing, the (a) Atomiser preheated to remove the binder and, finally, sintered.
pressure is equal in all directions which permits (b) Spray chamber with inert atmosphere
uniform density of the metal powder. y Volumetric shrinkage during sintering is very high.
(c) Mould for producing preforms.
preforms
(a) Both A and R are individually true and R is the y Complex shapes that are impossible with conventional
correct
co ect eexplanation
p a at o oof A y After the metal is atomised,, it is deposited
p into a cooler
compaction.
ti
(b) Both A and R are individually true but R is not the preformed mould.
correct explanation of A y Good dimensional accuracy.
(c) A is true but R is false y Achieve density above 99%, fine grain structure,
y High production rate.
( ) A is false but R is true
(d) mechanical
h i l properties
ti same as wrought
ht product
d t
550 551 y Good mechanical properties. 552
ForIESOnly ForIESOnly
R ll C
RollCompaction
ti l
ExplosiveCompaction
y Powders are compacted by passing between two rolls y High Energy Rate Forming (HERF) or Explosive Forming
rotating in opposite direction. of the metal powders at rather higher velocities 3500 m/s
y The powders are put in a container and are forced by a than
h thath off the
h usuall speedd off compaction
i during
d i the h
ram between two rotating rolls,
rolls and is compacted into a ordinary die compacting.
continuous strip at speeds of up to 0.5 m/s. y Higher green densities
y Sheet metal for electrical and electronic components and y Higher sintered strength
for coins can be made by this process.
process
y More uniform density distribution
y The rolling
g p
processes can be carried out at room or at
elevated temperature.
ForIESOnly
ISRO 2013
ISRO2013 FeaturesofPMproducts
f d
LiquidPhaseSintering
y During sintering a liquid phase, from the lower MP Following is a process used to form powder metal to y For
F high
hi h tolerance
l parts, a sintering
i i part is
i put back
b k into
i
component,
p , mayy exist a die and repressed. In general this makes the part more
shape
h accurate with a better surface finish.
y Alloying may take place at the particleparticle interface
y Molten
M l component may surround d the
h particle
i l that
h hash ( ) Sintering
(a) Si i y A part has many voids that can be impregnated.
impregnated One
not melted method is to use an oil bath. Another method uses
(b) Explosive
E l i Compacting
C ti vacuum
acuum first,
first then impregnation.
impregnation
y High compact density can be quickly attained
y A part surface can be infiltrated with a low melting point
y Important variables: (c) Isostatic Molding
metal to increase density, strength, hardness, ductility
y Nature of alloy, molten component/particle wetting, and impact resistance.
(d) All of these
capillary action of the liquid
y Plating, heat treating and machining operations can also
b used.
be d
556 557 558
For-2018 (IES,GATE & PSUs) Page 128 of 213 Rev.0
Productionofmagnets
d f Advantages
d Advantages
d Contd.
y 50:50FeAlalloysisusedformagneticparts
F Al ll i df i y Goodtolerancesandsurfacefinish
G d l d f fi i h y Physicalpropertiescanbecontrolled
y AlNiFeisusedforpermanentmagnets
p g y Highlycomplexshapesmadequickly
g y p p q y
y Variationfromparttopartislow
y Sinteringisdoneinawirecoiltoalignthemagnetic y Canproduceporouspartsandhardtomanufacture
polesofthematerial materials(e g cementedoxides)
materials(e.g.cementedoxides) y Hardtomachinemetalscanbeusedeasily
H dt hi t l b d il
y H2 isusedtorapidlycoolthepart(tomaintainmagnetic y Poresinthemetalcanbefilledwithother
y Nomoltenmetals
alignment) materials/metals
y Totalshrinkageisapproximately37%(foraccurateparts y Surfacescanhavehighwearresistance y Noneedformany/anyfinishingoperations
anextrasinteringstepmaybeaddedbeforemagnetic y Porositycanbecontrolled y Permitshighvolumeproductionofcomplexshapes
g p p p
alignment)
li t) y Lowwaste
y Thesinteringtemperatureis600CinH
g p y Allowsnontraditionalalloycombinations
2 y Automationiseasy
559 560 y Goodcontroloffinaldensity 561
IES2015
IES 1997 IES 2001 Consider the following statements regarding powder
metallurgy :
Which
Whi h off the h following
f ll i components can be b Carbidetipped
C bid i d cutting
i tools
l are manufactured
f d by
b
1. Refractory materials made of tungsten can be
manufactured by powder metallurgy methods? powder metal technology process and have a
manufactured easily.
easily
1. Carbide tool tips 2. Bearings composition of
2. In metal powder, control of grain size results in
3 Filters
3. 4
4. Brake linings (a) Zirconium
ZirconiumTungsten
Tungsten (35% 65%)
65%) relatively
l i l much h uniform
if structure
Select the correct answer using the codes given below: (b) Tungsten carbideCobalt (90% 10%) 3. The powder heated in die or mould at high temperature
(a) 1, 3 and 4 (b) 2 and 3 (c) Aluminium oxide Silica (70% 30%) is then pressed and compacted to get desired shape and
(d) NickelChromium Tungsten (30% 15% 55%) strength.
g
( ) 1, 2 and
(c) d 4 (d) 1, 2, 3 and d4
4. In sintering the metal powder is gradually heated
resulting in coherent bond.
bond
Which of the above statements are correct?
( ) 1, 2 and
(a) d 3 only
l (b) 1, 2 andd 4 only
l
574 575 (c) 2, 3 and 4 only (d) 1, 2, 3 and 4 576
For-2018 (IES,GATE & PSUs) Page 130 of 213 Rev.0
Pre Sintering IAS 2003 Repressing
y If a part made by PM needs some machining, it will be In
I parts produced
d d by
b powder d metallurgy
ll process, y Repressing is performed to increase the density and
presintering is done to
rather
h very difficult
d ff l iff the
h materiall is very hard
h d and
d (a) Increase the toughness of the component improve the
h mechanical
h l properties.
strong These machining operations are made easier by
strong. (b) Increase the density of the component y Further
F h improvement
i i achieved
is hi d byb resintering.
i i
the pre
presintering
sintering operation which is done before (c) Facilitate bonding of nonmetallic particles
(d) Facilitate machining of the part
sintering operation.
Infiltration
fl Impregnation OilimpregnatedPorousBronzeBearings
y Component is dipped into a low meltingtemperature y Impregnation
I i isi similar
i il to infiltration
i fil i
y PM component
p is kept
p in an oil bath. The oil p
penetrates
alloy
ll liquid
l d into the voids by capillary forces and remains there.
y The
Th liquid
li id would
ld flow
fl i
into the
h voids
id simply
i l byb capillary
ill y The oil is used for lubrication of the component when
necessary. During the actual service conditions, the oil is
action thereby decreasing the porosity and improving
action, released
l d slowly
l l to provide
d the
h necessary lubrication.
l b
the strength
g of the component.
p y The e co
components
po e ts ca
can abso
absorb
b bet
between
ee 12%% aand
d 30% o
oil by
volume.
y The p
process is used q
quite extensivelyy with ferrous p
parts
y It is
i being
b i used
d on P/M selflubricating
lf l b i ti b
bearing
i
using copper as an infiltrate but to avoid erosion, an alloy components since the late 1920's.
of copper containing iron and manganese is often used.
580 581 582
(b) sintering
(c) impregnation
(d) Infiltration
583 584 585
For-2018 (IES,GATE & PSUs) Page 131 of 213 Rev.0
IES 2014 IAS 2007 IAS 2004
The
Th process off impregnation
i i in
i powder d metallurgy
ll Consider
C id theh following
f ll i basic
b i steps involved
i l d in
i theh The
Th following
f ll i are the
h constituent
i steps in
i the h
technique is best described by which of the following? production of porous bearings: process of powder metallurgy:
(a) After sintering operation of powder metallurgy, rapid 1. Sintering 1. Powder conditioning
cooling is performed to avoid thermal stresses. stresses 2 Mixing
2. 2 Sintering
2.
(b) Low melting point metal is filled in the pores of a 3. Repressing 3. Production of metallic powder
sintered
d powder
d metallurgyll product
d 4. Impregnation 4. Pressing or compacting into the desired shape
(c) Liquid
qu d ooil oor g
grease
ease iss filled
ed in tthee po
pores
es o
of a ssintered
te ed 5. Colddiecompaction
C ld di ti I d tif the
Indentify th correctt order
d ini which
hi h they
th have
h t be
to b
powder metallurgy product performed and select the correct answer using the codes
g is the correct sequence
Which one of the following q of the
(d) During
D i sintering
i t i operation
ti off powderd metallurgy,
t ll above steps? given below:
b l
rapid heating is performed to avoid sudden produce of (a) 11234
234 (b) 33142
142
high internal pressure due to volatilization of lubricant
586 587 (c) 2413 (d) 4321 588
SwamiVivekananda
SwamiVivekananda
592
For-2018 (IES,GATE & PSUs) Page 132 of 213 Rev.0
Introduction y Cementedcarbides,
y Castcarbides,
y Success in metal cutting depends on selection of the
proper cutting tool (material and geometry) for a given y Coatedcarbides,
work material. y Coatedhighspeedsteels,
y A wide range of cutting tool materials is available with y Ceramics,
Cutt g oo ate a s
CuttingToolMaterials a varietyy of p
cost.
properties,
p , p
performance capabilities,
p , and y Cermets,
Cermets
y Whiskerreinforcedceramics,
y These include: y Sialons,
y High carbon Steels and low/medium alloy steels,
y Sinteredpolycrystallinecubicboronnitride(CBN),
Sinteredpolycrystallinecubicboronnitride(CBN)
y Highspeed steels,
y Sinteredpolycrystallinediamond,andsinglecrystal
y Cast cobalt alloys,
alloys naturaldiamond.
ldi d
BySKMondal 1 Contd
2 3
Carbon Steels
CarbonSteels
y Limited tool life. Therefore,, not suited to mass
production.
y Can be formed into complex shapes for small production
runs
y Low cost
y Suited to hand tools, and wood working
y Carbon content about 0.9 to 1.35% with a hardness
ABOUT 62 C Rockwell
y Maximum cutting speeds about 8 m/min. dry and used
upto 250oC
y The hot hardness value is low. This is the major factor in
FIGURE:Improvementsincuttingtoolmaterialshavereduced
tool life.
life
Fig.Productivityraisedbycuttingtoolmaterials
machiningtime. 4 5 6
13 14 15
16 17 18
For-2018 (IES,GATE & PSUs) Page 134 of 213 Rev.0
IES1995 IES2000 IES1992
Thecompositionsofsomeofthealloysteelsareas Percentageofvariousalloyingelementspresent ThemainalloyingelementsinhighspeedSteelin
under: indifferentsteelmaterialsaregivenbelow: orderofincreasingproportionare
1. 18W4Cr1V 1. 18%W;4%Cr;1%V;5%Co;0.7%C (a) Vanadium,chromium,tungsten
2 12Mo1W4Cr1V
2. 2. 8%Mo;4%Cr;2%V;6%W;0.7%C (b) Tungsten,titanium,vanadium
3. 6Mo6W4Cr1V
3 27%Cr;3%Ni;5%Mo;0.25%C
3. 27%Cr;3%Ni;5%Mo;0 25%C (c) Chromium,titanium,vanadium
Chromium titanium vanadium
4. 18W8Cr1V
4. 18%Cr;8%Ni;0.15%C (d) Tungsten,chromium,titanium
Thecompositionsofcommonlyusedhighspeedsteels
wouldinclude Whichoftheserelatetothatofhighspeedsteel?
(a) 1and2 (b) 2and3 (a) 1and3 (b) 1and2
(c) 1and4 (d) 1and3 (c) 2and3 (d) 2and4
19 20 21
IAS2001 IAS1994
Assertion(A):Forhighspeedturningofmagnesium Assertion(A):ThecharacteristicfeatureofHigh IAS
IAS 2013Main
2013 Main
alloys,thecoolantorcuttingfluidpreferrediswater speedSteelisitsredhardness.
misciblemineralfattyoil.
i ibl i lf il CompareHSSandceramictoolswithregardtotheir
Reason(R):ChromiumandcobaltinHighSpeed
Reason(R):Asarule,waterbasedoilsarerecommended promotemartensite formationwhenthetooliscold
p applicationinhighspeedmachining.
pp g p g
f hi h
forhighspeedoperationsinwhichhightemperaturesare
d ti i hi hhi ht t worked.
generatedduetohighfrictionalheat.Waterbeingagood
coolant theheatdissipationisefficient
coolant,theheatdissipationisefficient. ((a)) BothAandRareindividuallytrueandRisthecorrect
y
(a) BothAandRareindividuallytrueandRisthecorrect explanationofA
explanationofA (b) BothAandRareindividuallytruebutRisnot the
(b) BothAandRareindividuallytruebutRisnot thecorrect correctexplanationofA
e p a at o o
explanationofA (c) AistruebutRisfalse
(c) AistruebutRisfalse (d) AisfalsebutRistrue
(d) AisfalsebutRistrue
22 23 24
IES1995
y Speeds
S d up to 300 fpm
f are common on mild
ild steels
l
Thestraightgradesofcementedcarbidecutting
y Hot hardness p
properties
p are veryy g
good toolmaterialscontain
y Coolants and lubricants can be used to increase tool (a) Tungstencarbideonly
life, but are not required.
life required
(b) Tungstencarbideandtitaniumcarbide
y Special alloys are needed to cut steel
(c) Tungstencarbideandcobalt
(d) Tungstencarbideandcobaltcarbide
Contd
31 32 33
Reason (R): Carbides cannot be melted and cast. P01 Steel, Steel castings Precision and finish machining, high speed
P For machining long chip forming
(a) Both A and R are individually true and R is the common materials like plain carbon
P10 Steel Steel castings
Steel, Turning, threading,
Turning threading and milling high speed
speed,
small chips
correct explanation of A and low alloy steels P20 Steel, steel castings, Turning, milling, medium speed with small chip
malleable cast iron section
(b) Both A and R are individually true but R is not the M For machining long or short chip
correct
co ect eexplanation
p a at o oof A formingg ferrous materials like P30 Steel, steel castings, Turning, milling, medium speed with small chip
malleable
ll bl cast iiron section
i
Stainless steel
(c) A is true but R is false P40 Steel and steel casting Turning, planning, low cutting speed, large chip
K For machining short chipping,
chipping with
ith sand
d iinclusions
l i section
ti
(d) A is false
f l but
b R is true
ferrous and non- ferrous material P50 Steel and steel castings Operations requiring high toughness turning,
and non metals like Cast Iron,
Iron off medium
di or llow ttensile
il planning,
l i shaping
h i att llow cutting
tti speeds
d
Brass etc. strength
34 35 36
For-2018 (IES,GATE & PSUs) Page 136 of 213 Rev.0
K01 Hard grey C.l., chilled casting,
Al.
Al alloys with high silicon
Turning, precision turning and boring, milling,
scraping
IES1999 Ceramics
K10 Grey C.l. hardness > 220 HB.
Malleable C.l., Al. alloys
Turning, milling, boring, reaming, broaching,
scraping
MatchListI(ISOclassificationofcarbidetools)withList y Ceramics are essentially alumina ( Al2O3 ) based high
containing Si
II(Applications)andselectthecorrectanswerusingthe
pp g refractory materials introduced specifically for high
K20 Grey C.l. hardness up to 220 Turning, milling, broaching, requiring high codesgivenbelowtheLists: speed machining of difficult to machine materials and
HB toughness
ListI ListII cast iron.
iron
K30 Soft grey C.l.
C l Low tensile Turning reaming under favourable conditions
Turning,
strength steel A. P10 1. Nonferrous,roughingcut
K40 Soft non-ferrous metals Turning milling etc. y These can withstand very high temperatures, are
B. P505 2. Nonferrous,finishingcut
, g
M10 Steel steel castings
Steel, castings, Turning, milling,
Turning milling medium cutting speed and medium chemically more stable,
stable and have higher wear
manganese steel, grey C.l. chip section C. K10 3. Ferrousmaterial,roughingcut
M20 Steel casting, austentic steel, Turning, milling, medium cutting speed and medium resistance than the other cutting tool materials.
manganese steelsteel, chip section D.. K50
5 4. Ferrousmaterial,finishingcut
e ous a e a , s g cu
spherodized C.l., Malleable y In
I view
i off their
h i ability
bili to withstand
ih d high
hi h temperatures,
Code: A B C D A B C D
C.l. they can be used for machining at very high speeds of
M30 Steel austenitic steel,
Steel, steel Turning milling,
Turning, milling planning,
planning medium cutting speed,
speed (a) 4 3 1 2 (b) 3 4 2 1
spherodized C.l. heat medium or large chip section the
h order
d off 10 m/s.
/
resisting alloys
(c) 4 3 2 1 (d) 3 4 1 2
M40 Free cutting steel
steel, low tensile Turning profile turning
Turning, turning, specially in automatic
y Theycanbeoperatedatfromtwotothreetimesthe
y p
strength steel, brass and light machines. cuttingspeedsoftungstencarbide.
alloy 37 38 Contd
39
IAS1999 TiNCoatedHighSpeedSteel
Thecoatingmaterialsforcoatedcarbidetools, y Coated highspeed steel (HSS) does not routinely
includes provide as dramatic improvements in cutting speeds as
(a) TiC,TiN andNaCN (b) TiC andTiN do coated carbides, with increases of 10 to 20% being
(c) TiN andNaCN (d) TiC andNaCN typical.
i l
y In addition to hobs,, ggearshaper
p cutters,, and drills,,
HSS tooling coated by TiN now includes reamers, taps,
chasers spade
chasers, spadedrill
drill blades,
blades broaches,
broaches bandsaw and
circular saw blades, insert tooling, form tools, end
mills and an assortment of other milling cutters.
mills, cutters
58 59 Contd
60
C t
Cermets IES2010
y Physical
y p
vapour p
deposition (PVD) has p
proved to be the y These sintered hard inserts are made by combining cer
cer from
best process for coating HSS, primarily because it is a ceramics like TiC, TiN or TiCN and met from metal (binder) The
Th cutting
tti tool
t l material
t i l required
i d to
t
relatively low temperature process that does not likee Ni,, NiCo,
Co, Fee etc. sustain high temperature is
exceed the tempering point of HSS. y Harder, more chemically stable and hence more wear resistant
y More brittle and less thermal shock resistant
((a)) High
g carbon steel alloys
y
y Therefore,
Th f no subsequent
b t heat
h t treatment
t t t off the
th
cutting tool is required. y Wt% of binder metal varies from 10 to 20%. (b) Composite of lead and steel
y The advantage of TiNcoated HSS tooling is reduced y Cutting edge sharpness is retained unlike in coated carbide
inserts (c) Cermet
tool wear.
y Can machine steels at higher cutting velocity than that used for (d) Alloy of steel, zinc and tungsten
y Less tool wear results in less stock removal during tool tungsten carbide, even coated carbides in case of light cuts.
regrinding,
i di thus
h allowing
ll i i di id l tools
individual l to be b y Modern cermets with rounded cutting edges are suitable for
reground more times. finishing and semifinishing of steels at higher speeds, stainless
steels but are not suitable for jerky interrupted machining and
61 machining of aluminium and similar materials. 62 63
For-2018 (IES,GATE & PSUs) Page 139 of 213 Rev.0
IES2000 IES 2003 Di d
Diamonds
y Diamond is the hardest of all the cutting
g tool materials.
The
Th correct sequence off cutting i tools
l ini theh y Diamond has the following properties:
Cermetsare
ascending order of their wear resistance is y extreme hardness,
hardness
( ) Metalsforhightemperatureusewithceramiclike
(a) M l f hi h i h i lik
(a) HSSCast nonferrous alloy (Stellite)Carbide y low thermal expansion,
properties
Nitride y high
hi h heat
h conductivity,
d i i and d
(b) Ceramicswithmetallicstrengthandluster
(b) Cast nonferrous alloy (Stellite)HSSCarbide y a very low coefficient of friction.
(c) Coatedtoolmaterials Nitride
d y This is used when good surface finish and dimensional accuracy
(d) Metalceramiccomposites (c) HSSCast
SS Cast nonferrous
o e ous aalloy oy (Ste
(Stellite)Nitride
te) t de are desired.
Carbide y The workmaterials on which diamonds are successfully employed
are the nonferrous one, such as copper,
pp brass, zinc, aluminium
(d) Cast
C t nonferrous
f alloy
ll (St llit ) C bid Nit id
(Stellite)CarbideNitride and magnesium alloys.
HSS y On ferrous materials,, diamonds are not suitable because of the
diffusion of carbon atoms from diamond to the workpiece
64 65 66
material. Contd
y Diamond tools have the applications in single point turning and y Diamondtoolsofferdramaticperformance
GATE
GATE 2009(PI)
2009 (PI) boring
b i tools,
t l milling
illi cutters,
tt reamers, grinding
i di wheels,
h l honing
h i improvementsovercarbides.Toollifeisoftengreatly
tools, lapping powder and for grinding wheel dressing.
improved,asiscontroloverpartsize,finish,and
p p
Di
Diamond
d cutting
tti t l are nott recommended
tools d d for
f y Due
D to their
h i brittle
b i l nature, the h diamond
di d toolsl have
h poor
surfaceintegrity.
resistance to shock and so, should be loaded lightly.
machining of ferrous metals due to y Positiveraketoolingisrecommendedforthevast
y Polycrystalline diamond (PCD) tools consist of a thin layer (0.5
to 1.5 mm) of'fine grain size diamond particles sintered majorityofdiamondtoolingapplications.
(a) high tool hardness
together
h and d metallurgically
ll ll bonded
b d d to a cemented d carbide
bd y IfBUEisaproblem,increasingcuttingspeedandthe
substrate. useofmorepositiverakeanglesmayeliminateit.
p g y
((b)) high
g thermal conductivityy of work material
y The main advantages of sintered polycrystalline tools over
natural singlecrystal tools are better quality, greater toughness,
y Oxidationofdiamondstartsatabout450oCand
((c)) p
poor tool toughness
g
and improved wear resistance, resulting from the random thereafteritcanevencrack Forthisreasonthe
thereafteritcanevencrack.Forthisreasonthe
(d) chemical affinity of tool material with iron orientation of the diamond grains and the lack of large cleavage diamondtooliskeptfloodedbythecoolantduring
planes.
l cutting,andlightfeedsareused.
i dli h f d d
67 Contd
68 69
79 80 81
For-2018 (IES,GATE & PSUs) Page 141 of 213 Rev.0
IAS1998 C it
Coronite IES1993
y Coronite is made basically by combining HSS for strength and
Whichofthefollowingtoolmaterialshavecobalt toughness and tungsten carbides for heat and wear resistance. MatchListIwithListITandselectthecorrectanswerusingthe
codesgivenbelowthelists:
asaconstituentelement? y Microfine TiCN particles are uniformly dispersed into the matrix.
matrix Li I(CuttingtoolMaterial)
List I(C i lM i l) List
Li II(Major
II(M j
y Unlikeasolidcarbide,thecoronite basedtoolismadeofthree characteristicconstituent)
1. Cementedcarbide 2. CBN A. Highspeedsteel 1. Carbon
layers;
3. Stellite 4. UCON y thecentralHSSorspringsteelcore
B. Stellite 2. Molybdenum
C. Diamond 3. Nitride
Selectthecorrectanswerusingthecodesgivenbelow: y alayerofcoronite ofthicknessaround15%ofthetool D. Coatedcarbidetool 4. Columbium
Codes: diameter 5. Cobalt
y athin(2to5m)PVDcoatingofTiCN C d A
Codes: B C D A B C D
(a) 1and2 (b) 1and3 (a) 2 1 3 5 (b) 2 5 1 3
y The coronite tools made by y hot extrusion followed byy PVD (c) 5 2 4 3 (d) 5 4 2 3
(c) 1and4 (d) 2and3 coating of TiN or TiCN outperformed HSS tools in respect of
cuttingg forces, tool life and surface finish.
82 83 84
85 86 87
91 92
DN 30 1000
Speed (V ) = m / min = m / min = 94.2 m / min
1000 1000
IES-2001 Page No.1 Slide No.6 Ans. (c) For cutting brass recommended rake angle is -5 to +5
degree.
IES-1995 Page No.1 Slide No.7 Ans. (a) It is true form-cutting procedure, no rake should be
ground on the tool, and the top of the tool must be horizontal and be set exactly in line with the axis of
rotation of the work; otherwise, the resulting thread profile will not be correct. An obvious disadvantage
of this method is that the absence of side and back rake results in poor cutting (except on cast iron or
brass). The surface finish on steel usually will be poor.
GATE-1995;2008 Page No.1 Slide No.8 Ans. (a) Increasing rake angle reduces the cutting force
on the tool and thus power consumption is reduced.
IES-1993 Page No.1 Slide No.9 Ans. (d) Negative rake angle increases the cutting force i.e.
Cutting force
specific pressure. Specific pressure =
feeddepth of cut
IES-2005 Page No.2 Slide No.10 Ans.(b) Carbide tips are generally given negative rake angle it
is very hard and very brittle material. Negative rake is used as carbides are brittle not due to hardness.
Hardness and brittleness is different property
IES-2002 Page No.2 Slide No.12 Ans.(c) Carbide tools are stronger in compression.
IES-2011 Page No.2 Slide No.13 Ans. (b) The rake angle does not have any effect on flank but
clearance anglehas to reduce the friction between the tool flank and the machined surface.
GATE-2008(PI) Page No.2 Slide No.14 Ans. (c) Brittle workpiece materials are hard and needs
stronger tool. Tools having zero or negative rake angle provides adequate strength to cutting tool due to
large lip angle.
IES-2012 Page No.2 Slide No.17 Ans.(d) When cutting velocity is increased, it will lead to
increase in power and temperature, and cutting force will be slightly reduce so we take as cutting forces will not
be affected by the cutting velocity. Common sense will say force will increase, but if you think deeply
there is no reason for increasing the force, same material same hardness, same tool same sharpness.
Therefore the force will remain unaffected. But in actual practice it will reduce due to high
temperature. As velocity increases power consumption will increase and temperature will increase.
IES-2006 Page No.2 Slide No.18 Ans. (d) All other tools are multi-point.
IES-2010 Page No.3 Slide No.26 Ans. (c) Fy = Ft cos = Ft sin CS (radial force)
Fx = Ft sin = Ft cos CS (axial force)and SCEA has no influence on cutting force i.e. tangential force. But
this question is not for Orthogonal Cutting it should be turning.
IES-2006 Page No.4 Slide No.28 Ans.(c) Smaller point angle results in higher rake angle.
IES-2002 Page No.4 Slide No.29 Ans. (d)Strength of a single point cutting tool depends on lip
angle but lip angle also depends on rake and clearance angle.
IES-2009 Page No.4 Slide No.31 Ans. (c)Large nose radius improves tool life. A sharp point on the
end of a tool is highly stressed, short lived and leaves a groove in the path of cut. There is an
improvement in surface finish and permissible cutting speed as nose radius is increases from zero value.
But too large a nose radius will induce chatter.
IES-1995 Page No.4 Slide No.32 Ans. (c) It will increase tool cutting force.
IES-1993 Page No.4 Slide No.35 Ans. (b)The second item is the side rake angle. Thus 6 is
the side rake angle.
ISRO-2011 Page No. 4 Slide No.36 Ans. (b)
GATE-2008 Page No. 5 Slide No.37 Ans.(d) We may use principal cutting edge angle or approach
angle = 90 - CS . When, principal cutting edge angle =90;then S = . Dont confuse with side cutting
edge angle. Side cutting edge angle is not principal cutting edge angle.
t 0.81
GATE-2011Page No.5 Slide No.39 Ans. (b) r = = = 0.45
tc 1.8
r cos 0.45cos12o
= tan 1 = tan 1 = 25.90o
1 r sin 1 0.45sin12o
IES-1994 Page No.5 Slide No.41 Ans. (b) Shear angle does not depends on velocity.
lc 68.9 r cos
IES-2014 Conventional Page No. 5 Slide No. 42 Ans. 18.3o r = = and tan =
l 69 1 r sin
= 10o
t = 0.5 mm
tc = 1.125 mm
t 0.5
r= = = 0.444
tc 1.125
r cos 0.444 cos10
tan = =
1 r sin 1 0.444 sin10
= 25.35o
= cot + tan( ) = cot 25.35o + tan(25.35o 10o ) = 2.385
IES-2009 Page No.6 Slide No.46 Ans. (d)as rake angle is zero. shear strain ( ) = cot + tan
= cot + tan ( 12 )
d
= cos ec 2 + sec 2 ( 12 ) = 0 gives = 51o
d
V Vs V
IES-2016 Page No.6 Slide No.48 Ans.(a) = = c
cos ( ) cos sin
GATE-2012 Page No. 6 Slide No.49 Ans. (c)
IES-2006 Page No.6 Slide No.51 Ans. (c) Cutting torque decreases with increase in rake angle.
VC V
=
sin sin ( 90 + )
35 sin 45
VC = = 28.577m / min
sin ( 90 + 15 45 )
IES-2014 Page No.7 Slide No.55 Ans. (c)f = f sin = 0.2 sin 90 = 0.2 mm ; tc= 0.32 mm;
cutting ratio = chip thickness ratio = t / tc = 0.2/0.32 = 0.625 But examiner has given reciprocal value = 1.6
IES-2001 Page No.7 Slide No.56 Ans. (a) Most of the students get confused in this question.
Velocity of chip sliding along the shear plane is shear velocity (Vs) and velocity of chip along rake
face is chip velocity (Vc ).
GAT
TE-2009 (PI -common
n data S-1) Page No.7 Slide No.63 Ans.(c))
m ; tc = 0.44 mm; = 155
t = 0.2 mm
t r cos 0.5cos15
r = = 0.5; = tan
t 1 = tan 1 = 29.02
tc 1 r sin 1 0.5sin155
Nearesst option is ( c )
GAT
TE-2009 (PI- common
n data S-2) Page No.8 Slide No.64 Ans. (b
b)
V
V = 20 m / min; C = r = 0.5 orrVC = 10 m / min
V
IES
S-2007 Pag
ge No.8 Slide No.66
N Anss. (b)
IES
S-2015 Pag
ge No.8 Slide No.67
N Anss. (c)
IAS
S-1997 Pag
ge No.8 Slide No.68
N Anss. (a)
Ch
h-2: An
nalysis of Mettal Cuttting: Answer
A rs with
h Expla
anation
ns
ESE
E-2000(co
onvention
nal) Pag
ge No.9 Slide No
o.73
Ans.
GA
ATE-2008 (PI) Link
ked S-1 Page No..10 Slide No.87 Ans. ((d)
Forr minimum cutting
c forcee we have too use mercha
ant Theory
= 10 , = 0.7 = tan or = tan 1 = 34.99
Using Merchant
M A
Analysis
= 45 +
2 2
10 34.99
= 45 + = 32.5
2 2
GA
ATE-2008 (PI) Link ked S-2 Page No..10 Slide No.88 Ans. ((b)
b = 3.6 mm
Calculaating shear force
f Fs :
bt 3.6 mm 0.25
0 mm
Fs = y 60 ( N / mm 2 )
= 46 = 770.52
7 N
sin sin 322.5
Using Merchant
M C
Circle:
In trianngle formed by Fs , Fn an
nd R;
c ( + )
Fs = R cos
or 770.52 N = R ( N ) cos(32.5 + 34.99 10 ) R = 1433.7 N
In trianngle formed by Ft , Fc an
nd R;
Fc =Rcoos ( ) = 1433.7 co
os(34.99 110 ) = 1299.5 N
1500
=FC iV = 129
Power= 48.8W 3.2
m / s = 324
99.5 N 25 KW
60
GA
ATE-2014 Pagge No.10 Slide No.89 Ans. (d)
Using Merchant Analysis, = 45 +
2 2
As shear anglee increases cutting force will decrease and lengtth of shear p
plane decrea
ased results chip
thicckness decreease.
GA
ATE-2014 Pag
ge No.10 Slide No.90 Ans. (a)
Ussing Merchaant Analysiss, = 45 +
2 2
As shear anglee increases area
a of the shear plane e decreased,, it results ccutting force
e hence imp
prove
surrface finish. Here option
n (b) is also correct
c but best
b one is op
ption (a).
IES
S-2010 Page No..11 Slide No.92 Ans. (b) Mercha ant Analyssis
IES
S-2005 Page No..11 Slide No.93 Ans. (a)
IES
S-2003 Page No..11 Slide No.98 Ans.(c c)
Fs = Fc cos Ft sin = 900
9 cos 30 600sin 30 = 479.4N
IES
S-2014 Page No..11 Slide No.99 Ans. (b)(
N = Fc = 1000 N
F 500 1
= = =
N 1000 2
IES-2016 Page No.12 Slide No.101 Ans. 0.5
F Fc sin + Ft cos 500 sin 0 + 250 cos 0
= = = = 0.5
N Fc cos Ft sin 500 cos0 250sin 0
GATE-2007 (PI) Linked S-1 Page No.12 Slide No.102 Ans. (a)
FC = 1200 N ; Ft = 500 N ; = 0
GATE-2006 common data Q-1 Page No.12 Slide No.107 Ans. (b)
= 15; t = 0.5mm; tc = 0.7mm; Fc = 1200 N ; Ft = 200 N
t 0.5
r= = = 0.7142
tc 0.7
r cos 0.7142 cos15
= tan 1 = tan 1 = 40.24
1 r sin 1 0.7142sin15
F = Fc sin + Ft cos =1200sin15 + 200 cos15 = 503.77 N
N = Fc cos Ft sin = 1200 cos15 200sin15 = 1107.3 N
F 503.77
= = = 0.455 0.46
N 1107.3
Alternatively
Using Merchant Theory:
= 45 +
2 2
15
= 45 + 40.24 = 24.5
2
= tan = tan 24.5 = 0.456 0.46
GATE-2006 common data Q-2 Page No.12 Slide No.108 Ans.(a)
IES-1995 Page No.13 Slide No.112 Ans. (b) Tangential force accounts for 99% of
the power consumption.
IES-2001 Page No.13 Slide No.113 Ans. (a)
IES-1997 Page No.13 Slide No.114 Ans. (c)
IES-1999 Page No.13 Slide No.115 Ans. (a)
GATE-2014 Page No.14 Slide No.118 Ans.0.08to0.12
t = f sin
= 90 CS = 90 60 = 30
t = 0.2sin 30 = 0.1 mm
ESE-2003(conventional) Page No.14 Slide No.119 Ans.
GA
ATE-2015 Pag
ge No.14 Slide No.124
4 An
ns. 18.88
GA
ATE-2015 Pag
ge No.14 Slide No.125
5 An
ns. (a)
GA
ATE-2016 Pag
ge No.14 Slide No.126
6 Anss.(b)
Fx 800
We know; Ft = = = 800 N
sin sin 90
Using relations:
F = Fc sin + Ft cos = 1000sin 0 + 800 cos 0 = 800 N
N = Fc cos Ft sin = 1000 cos 0 800sin 0 = 1000 N
F 800
= = = 0.8
N 1000
GATE-2003(common data)S-1 Page No.15 Slide No.128 Ans. (a)
f = 0.25 mm / rev, d = 0.4 mm, = 10, = 27.75
t = f sin = 0.25sin 90 = 0.25 mm
r cos r cos10
tan = =
1 r sin 1 r sin10
r cos10
tan 27.75 =
1 r sin10
t 0.25
r = 0.4888 = =
tc tc
tc = 0.51138 mm
GATE-2003(common data)S-2Page No.15 Slide No.129 Ans. (d)
using Merchant Analysis;
=45+
2 2
10
27.75 = 45 + = 44.5
2 2
= tan = tan 44.5 = 0.9826
GATE-2008(common data)S-1 Page No.15 Slide No.130 Ans. (d)
y = 250 MPa;V = 180 m / min;
f = 0.20 mm / rev; d = 3 mm; r = 0.5; = 7
r cos 0.5cos 7
= tan 1 = tan 1 = 27.85 28
1 r sin 1 0.5sin 7
We know;
d = b sin
.........( = 90); d = b & t = f
t = f sin
bt 0.20 3
Fs = y = 250 = 321.09 N 320 N
sin sin 27.85
=
4
(10 2
)
92 175 mm3 / min = 2611.45 mm3 / min
8 3
81 90
or = = 1.5
36 60
In1.5
n= n = 0.5
81
In
36
C =60 810.5 = 90 360.5 = 540 = K
1 = ( 2)
1/0.5
= 1 = 300%
T1 V2
IFS-2013 Page No.25 Slide No.225 Ans.
Using Taylor's Tool Life Equation:
V1T1n = V2T2 n
or 100 120n = 130 50n
or n = 0.2997 0.3
NowC = 100 1200.3 = 420.49
Tool life when cutting speed is 2.5 m/s = 2.5 60 m/min
( 2.5 60 ) T 0.3 = 420.49
or T = 31.06 min
Velocity when tool life is 80 min
V 800.3 = 420.49
or V = 112.94 m / min
GATE-2010 Page No.26 Slide No.226 Ans.(a)
for Carbide n1 = 1.6, K 1 = 90
for HSS n2 = 0.6, K 2 = 60
Using Taylor's Tool Life Equation:VT n =C
let cutting speed is x m/min
1
90 0.45
xTA 0.45
=90 TA =
x
1
60 0.30
and xTB 0.3
= 60 TB =
x
for TA >TB
1 1
90 0.45 60 0.30
x >
x
Solve for x using calculator, x = 26.7 m/min
GATE-2013 Page No.26 Slide No.227 Ans.(b)
for A n1 = 0.45, K1 = 3000
for B n2 = 0.3, K 2 = 200
Using Taylor's Tool Life Equation:VT n =C
let cutting speed is x m/min
1
3000 1.6
xTc
1.6
=3000 Tc =
x
1
200 0.6
and xTH 0.6
= 200 TH =
x
Ct = + Now T = =
V VT V V
18C 270C
Ct = + 4
V 150
V
V
dCt 18C 270C 3V 2
= 2 + =0 orV = 57.91 m / min
(150 )
4
dV V
GATE-2005 Page No.30 Slide No.268 Ans.(a)
IAS-2007 Page No.30 Slide No.269-270 Ans.(b)
IES-2011 Page No.31 Slide No.271 Ans.(d)
IES-1999 Page No.31 Slide No.273 Ans.(c)
IES-1998 Page No.31 Slide No.274 Ans.(c)
IAS-2002 Page No.31 Slide No.275 Ans.(c)
The minimum cost criterion will give a lower cutting speed i.e. lower prodeuction rate, while the
maximum production rate criteria will result higher cutting speed i.e. higher cost per piece as it reduces
tool life.
IAS-1997 Page No.31 Slide No.276 Ans.(b) it is less than one but very close to each other so 0.1 is not
possible.
IES-2000 Page No.31 Slide No.277 Ans.(a)
IES-2004 Page No.31 Slide No.278 Ans.(a) To improve MRR = fdv i.e. productivity we can increase
velocity or feed. but increase in velocity will reduce the tool drastically so will increase cost more than
feed.
IES-2002 Page No.31 Slide No.279 Ans.(c)
IAS-2007 Page No.32 Slide No.280 Ans.(a)At optimum cutting speed for the minimum cost of
machining gives low production rate.
IES-2010 Page No.32 Slide No.281 Ans.(d) After some time cutting speed will be so that tool
changing time will be significant.
IES-2012 Page No.32 Slide No.285 Ans.(d)
IAS-1996 Page No.32 Slide No.286 Ans.(d) Machinability is a comparative measure not absolute.
IES-1992 Page No.33 Slide No.291 Ans.(a) large grain means soft workpiece material.
IAS-2000 Page No.33 Slide No.293 Ans.(a)Built up edge protects the cutting edge of the tool from
wear, So tool life increased but it changes the geometry of the cutting.
IES-1992 Page No.33 Slide No.297 Ans.(a)
IES-2007,2009 Page No.34 Slide No.298 Ans.(a)Machinability: Machinability can be tentatively defined as
ability of being machined and more reasonably as ease of machining.
Such ease of machining or machining characters of any tool-work pair is to be judged by:
Magnitude of the cutting forces
Tool wear or tool life
f2 f2
we know : h = or 5 106 = or f = 2.68 104 m / rev = 0.268mm / rev
8R 8 1.8 103
GATE-2007(PI) Page No.35 Slide No.314 Ans.(a)
f = 1mm / rev; SCEA = 30; ECEA = 10
f 1
Using formula: h = = = 0.16mm
tan SCEA + cot ECEA tan 30 + cot10
GATE-2005 Page No.35 Slide No.315 Ans. (b)
f
Using formula:h =
tan SCEA + cot ECEA
f f
hP = and hQ =
tan 30 + cot 8 tan15 + cot 8
h
P =
( tan15 + cot 8)
hQ ( tan 30 + cot 8 )
IES-1993, ISRO-2008 Page No.36 Slide No.316 Ans. (c) Surface roughness is directly dependent on
square of feed. Slow cutting results in formation of built-up edge, but after certain speed the finish
remains same. Rake angle has noticeable effect at slow speeds, but its effect is small at speeds, used for
finish machining. So f has maximum effect.
IES-2006 Page No.36 Slide No.317 Ans. (a) refer previous question
max clearance = upper limit of hole - lower limit of shaft = 40.50-39.95 = 0.1 mm
GATE-2015 Page No.39 Slide No.20 Ans.(b)This being an clearance fit , so minimum clearance will
be
Min C= LL of hole UL of Shaft
Min C = 25.020-25.005 mm = 0.015 mm
GATE -2012 Same Q in GATE-2012 (PI) Page No.40 Slide No.33 Ans.(c)
Maximum Interference = Maximum size of shaft Minimum size of hole
= (25 + 0.04) (25 + 0.02) mm = 20 m
IAS-2011(main) Page No.40 Slide No.34 Ans.
LL of L4 = LL of L1 UL of L2 UL of L3
= 21.99-10.005-10.005=1.98mm
UL of L4 = UL of L1 LL of L2 LL of L3
= 22.01-9.995-9.995=2.02mm
GATE-2007(PI) Page No.46 Slide No.89 Ans.(a) It requires centre.
GATE-2007(PI) Page No.46 Slide No.90 Ans.(d)
Before plating the hole size will be bigger ,
Maximum limit will correspond to min thickness;so,
min thickness = 2 (10 103 ) mm = 0.02mm
Max limit = max size of hole + min thickness = 30.050+0.02=30.07 mm
Minimum limit will correspond to max thickness;so,
max thickness = 2 (15 103 ) mm = 0.03mm
Min limit = min size of hole + max thickness = 30.010+0.03=30.04 mm
GO ring gauge will inspect maximum metal conditions i.e. UL of shaft i.e. Largest size after platting.
UL after platting = 25.02 + 2.005 + 2.005 mm = 29.030 mm
ISRO-2010 Page No.53 Slide No.145 Ans.(c) A measuring device of a standard size that is used
to calibrate other measuring instruments.
ISRO-2008 Page No.53 Slide No.146 Ans.(d) Primary standards are used for calibration only.
In workshop it has no use.
GATE-2007(PI) Page No.53 Slide No.149 Ans.(d) During the measurement, a comparator is able to
give the deviation of the dimension from the set dimension. Cannot measure absolute dimension but can only
compare two dimensions. (Rest all the options will give reading of the dimension measured it will not compare)
ISRO-2011 Page No.55 Slide No.163 Ans.(c) A sine bar is specified by the distance between the centre
of the two rollers
GATE-2012(PI) Page No.55 Slide No.164 Ans.(a)
L
GATE-2011(PI) Page No.56 Slide No.174 Ans.(a)
p 2.5 60
Best Wire Size : d = sec = sec = 1.443 mm
2 2 2 2
GATE-2013 Page No.56 Slide No.175 Ans.(none) refer formula
IES-2017(Pre) Page No.56 Slide No.176 Ans(c)
GATE-2011(PI) Page No.56 Slide No.177 Ans.(c)
Difference between the readings of micrometers= 16.532-15.398=1.134mm
Diameter of cylindrical standard = 30.5mm
Effective diameter= 30.5-1.134=29.366mm
IES-2012 Page No.57 Slide No.187 Ans. Refer slides for theory
GATE-2017(PI) Page No.57 Slide No.189 Ans.(b)
Parallelism Error =
(14 10 ) 0.5086 m = 0.5086 m
4
Ch-6 Miscellaneous of Metrology: Answers with Explanations
GATE-1998 Page No.63 Slide No.237 Ans. (c) Autocollimator isan optical instrument for non-contact
measurement of small angles or small angular tilts of a reflecting surface
GATE-2009(PI) Page No.63 Slide No.238 Ans. (a)
GATE-2014 Page No.63 Slide No. 239 Ans. (b) Autocollimator is also measure flatness.
ISRO-2010 Page No.63 Slide No. 242 Ans. (b) In optical square two mirrors are placed at an angle of
45o to each other and at right angles to the plane of the instrument. Angle between the first incident ray and
the last reflected ray is 90o.Two mirrors may be replaced by two prisms.
IES-1998 Page No.64 Slide No.245 Ans. (d)
GATE-2014 Page No.64 Slide No. 248 Ans. (c) Laser interferometer is widely used to check and
calibrate geometric features of machine tools during their assembly
GATE-1992 Page No.65 Slide No. 254 Ans. (b)
GATE-2004 Page No.65 Slide No. 257 Ans. (b)
GATE-1995 Page No.65 Slide No. 259 Ans. (b)
GATE-2010 Page No.66 Slide No.263 Ans. (a)
C2 A 3
tan = =
2 5 + 15.54 + 8 28.54
= 6.006
2
= 12.001
BC = (H2 + d2/2) ( H1
+ d1/2) = 35.55 + 60/2 -
20.55 40/2 = 25 mm
AC = 60/2 + 40/2 = 50
mm
AB = ( 50 2
)
252 = 43.3
This question is wrong. For proper calculation we need velocity of neutral plane or velocity of roller. But in this
question velocity of exit is given. From velocity of exit we may assume the velocity of neutral plane but cant
calculate correctly.
After IITs answer we will challenge and confirm the answer. I have given best answer for this question.
= average velocity ( V ) =
V +V
o f
=
27 + 30
= 28.5 m / min
2 2
Now,V = DN
or 28.5 = 0.300 N
or N = 30.24 rpm
Total power for two roller ( P )
2 N 2 30.24
= 2T = 2 1439.9 , W = 9.1195 KW 9.12 KW
60 60
IES 2000, GATE-2010(PI) Page No.82 Slide No.137 Ans.(a)The roll-separating force which separates
the two rolls apart can be obtained by multiplying the average roll pressure with the total contact area.
The average roll pressure can be decreased by reducing the maximum pressure, which is a function of
the contact length. Smaller contact lengths means lesser friction forces acting. Thus, by reducing the
contact length, it is possible to decrease the roll-separating force. This in turn, can be achieved by
reducing the roll diameter, since; smaller rolls would have less contact length than larger rolls for the
same reduction.
IAS-2007 Page No.82 Slide No.138 Ans.(c)Use small dia rolls to reduce Roll force.
IES-2001 Page No.82 Slide No.139 Ans.(a)Coefficient of friction is constant over the arc of contact
and But does not acts in one direction throughout the arc of contact.
IAS-1998 Page No.82 Slide No.141 Ans.(d)
vesign indica
negativ ates compresssive strain.
GAT
TE-2017(PII) Pagge No.91 Slide No. 221 2 Ans. 1.8
833 Range (1.80 to 1.8
85)
GAT
TE-2016 Page No.91
1 Slide No.
N 222 Anss.(b)
L Lo / 2
T = ln = ln = ln 2 = 0.69
Lo L o
TE-2017
GAT Page No.91
1 Slide No.
N 223 Anss.(b)
TE-2006
GAT Page No.92
2 Slide No.
N 227 Anss.(b)
or = or d f = 111.8 mm
4 4
do2 1002
Initial Force( Po ) = o = 80 = 628.3 KN
4 4
d 2f 111.82
Final Force( Pf ) = o = 80 = 785.35 KN
4 4
Po + Pf 628.3 + 785.35
AverageForce( Pavg ) = = = 706.8 KN
2 2
( )
Workdone(W ) = Pavg ho h f = 706.8 (50 40) J = 7068 J
mg(h + x ) = W [ x = ho h f ]
10 103 ( h + 0.010 ) = 7068 or h = 0.6968 m
d = 1
B ro
d =
1 = 338.653MPa
1.7145 6.25
Force ( P ) = 338.653 102 N
4
100
Power = P V = 338.653 102 m / s = 44.329 kW
4 60
Maximum possible reduction; o = d
o (1 + B )
rf min 400(1 + 1.7145) rf min
2B 21.7145
d = 1 + . b
B ro ro
21.7145
400(1 + 1.7145) 5 5
21.7145
d = 1 + 50 = 361.26MPa
1.7145 6.25 6.25
For maximum possible reduction; o = d
o (1 + B ) rf min rf min
2B 2B
o = 1 + . b
B ro ro
21.7145
GATE 2011 (PI) Common Data-S1 Page No. 104 Slide No. 339 Ans.(c)
d 2
10 2
Initial area ( A o ) = o
= mm 2 = 78.54 mm 2
4 4
After first pass area ( A1 ) = (1 0.35 ) Ao = (1 0.35 ) 78.54 mm 2 = 51 mm 2
After second pass area ( A 2 ) = (1 0.35) Ao and then ........
2
L A 78.54
True strain = ln = ln o = ln = 3.02
Lo A 3.85
and Ao Lo = A7 L7 or 78.54 100 = 3.85 L7 L7 = 2040 mm
GATE 2011 (PI) Common Data-S-2 Page No. 104 Slide No. 340 Ans. (d)
A A 78.54
P = o Af ln o = o A1 ln o = 200 51 ln N = 4.40 KN
Af A1 51
F=
( d1t + d 2t ) pt = ( 25.4 1.5 280 + 12.7 1.5 280 ) 0.6 1.5 = 23.81KN
S + pt 1 + 0.6 1.5
GATE-2010 Statement Linked 1 Page No.108 Slide No. 374 Ans.(a)
p
t = 5 mm; L = 200 mm; = 100MPa; = 0.2
t
Fmax = Lt = 200 5 100 = 100 kN
Work Done = Fmax ( pt ) = 100 (0.2 5) = 100 J
Instanta
aneous area
a
W
Where T annd F is thee engineering stress and
a engineeering strain
n respective
ely.
Trrue strain
L
Elongation
E dxx L A d
FT
ln ln 1 F
ln o 2 ln o
Instan
ntaneouslennght L x Lo A d
o
ng strain ( F ) = e FT -1
orr engineerin
h
h1
2L
2L1
B Wx
x
Forgingoccursinplassticzonei.einbetween V y and Vult (Vx+d Vx)
h x
V y YieldStress x =0
V o For forging,
f we need flow stress
s and fllow stress iss not constaant and depends on stress of the 2L
L Wx
P
workpiecee.
Vult Ultimmatetensilestresshereneckformationstarts. x 0 , is the point at
a which thhe material does not move
m in any
y direction.
Take an element dxx at a distance of x (en
nlarged view
w):
2. Trescas Theory
y: V1 V3 V0
dx
PBd
W Bdx
F = N
N
or dF = dN
Wx B dx P . PB dx
Wx PP
From equ
uation (1) and
a (3)
d V x 2W x
0
dx h
d P 2P P Elementa
al force, dF
F = P.B.dx
or 0 2P
(L x )
dx x h dF = 2K e h . B.dx
dP 2P
or P h dxx L 2P
. (L x ) L L
Integratiing, F 2 u (2 K . e h
. B . dx ) ' gives half we use 2
h portion F so for 2L w
2P 0 0 0
or ln P x C ......(4) L 2P
h (L x )
F 4 KB . e h . dx
0
Condition-2:
Consid
dering sticking frriction all over the surfac
ce ( Wx Wy K )
Shear faiilure will occur at each and everry point.
dVx 2Wx
For Slidiing Region: 0
dx h
Ps
K
....(9) or F 2u
0
16.16
6 39.68
6
150 . dx
P
510 kN 29.10 kN 539 kN (Von Mises)
At x xs ; P Ps
Vo K 3.5
2P
(L x s ) Applying Trescas Theory, K 3.5 N / mm2 ; Ps 14 N / mm2
Ps 2K e h 2 P 0.25
2P 39.68 2u0.25 48
K h
(L xs ) 2 u 3.5 (48 x )
P
2K e F 2u
14
6
(39.68 x ) 150 dx 2 (2 u 3.5) e 6
150 dx
or 0 39.68
1 2P
(L xs ) 442 kN 25 kN 467kN (Tresca ' s)
eh
or 2P
1 2P Practice Problem-1
ln (L x s )
or 2P h A strip of metal with initial dimensions 24 mm x 24 mm x 150 mm is forged between two
h 1 flat dies to a final size of 6 mm x 96 mm x 150 mm. If the coefficient of friction is 0.05,
. ln L xs
2P 2P
determine the maximum forging force. Take the average yield strength in tension is 7
h 1
xs L ln ....(10) (in any ques
stion first w
we find thiss xs )
2P 2P N/mm2
Using this equation
n we can deecide the coondition of friction.
f
Given: 2L = 96 mm; L = 48 mm; h = 6 mm; B = 150 mm; P 0.05
Example 1: L = 50 mm, h = 10 mm & P 0.25
h 1
h 1 10 1 xs L ln K = 4.04 N/mm2
xs L ln
n 50 ln
n 36.13mm 2P 2P
2P 2P 2 u 0.25 2 u 0.25
xs 90.155 mm
0 to 36.13 mm stick
king and 36
6.13 mm to 50 mm slid
ding will ta
ake place.
Since xs came negative so there will be no sticking only sliding will take place.
48 2u0.05
(48 x )
6
4 u 4.04 u 150 e
0
dx 177.98 kN
R
h1
VT dVT
VT
r VT drh
Vr
T
dT
VTdr.h sin dT 2 VTdr.h sin dT
2 2
For Axi--Symmetr
ry forging
r T
i.e. Vr V T
From aboove equatioon,
dT
( Vr d Vr ) ( r dr ) dT . h ( Vr . r dT . h ) 2 Wr . r dT . dr 2 Vr dr h . 0
2
d T dT
U sin g : V T Vr ; sin |
2 2
Vr d Vr ) (r dr ) . h ( Vr . rh) 2Wr . r dr Vr . dr
(V d .h 0
or
At r = R; Pmin V0
Here r = 0 means a point
V1 V3 V0
Vr P V0 ...(2)
or
2. Von Miscs
M Theo
ory:
V1 V2 )2 ( V2 V3 )2 ( V3 V1 )2
(V 2 V20
2 2 2
( Vr Vr ) ( Vr P) ( P Vr ) 2 V20 ding force
For find
or
2 ( Vr P)2 2 V20 Elementaal force (dF
F)
or
V P
r 0V ...(2)
or dr
On differrentiating; r R
d Vr d P
0
dr dr
d Vr dP
...(3)
dr dr Sr dr
dA = 2S
dF = d F P . 2Sr . drr
Condittion 1: 2P
(R r )
Consid
dering sliding
s f
friction all over
r the sur
rface dF V 0 .eh . 2Sr . dr
R 2P
Wr PP . (R r )
orr F 2SV0 r.e h
dr
d P 2Wr
From (1) and (3); 0 0
dr h
R
2P
(R r ) 2P
(R r )
dP PP r . e h eh
2. 0 orr F 2SV0 1 . d
dr
or dr h 2P 2P
dP 2 P P h h 0
R
or dr h 2P
(R r )
2P
(R r )
r.eh eh
dP 2P orr F 2SV0
or 2P P
2
P
h
. dr
2
h h 0
2P
ln P .r C ...(4) 2P
R
h R 1 eh
At r = R; Vr 0 (becausse on this su
urface therre will be noo force) and
d Vr P V 0 ; P V0 orr F 2S V 0 0
2P 2 P
2
2 P
2
2P . R h h h
ln V0 C
or h
surface
Wr K
From (1) equation (3)
d V r 2 Wr
0
dr h
d P 2K
0
or dr h
2K
or dP
h
. dr
2K
or P .r C ...(6)
h
At r = R; Vr 0 (because on this surface there will be no force) and Vr P V0 ; P V0
2K
V0 .RC
h
ng
ki
ic Ps According to Von-Miscs Theory
St
Sticking V0 K 1
r = Rs K or
3 V0 3
h 1
Rs R ln ...(11)
2P 3 P
IES2006Conventional
A certain disc of lead of radius 150 mm and thickness 50 mm is reduced to a thickness of 25
mm by open die forging. If the co-efficient of friction between the job and die is 0.25,
For sliding region pressure distribution is same as we derived in previous condition same
determine the maximum forging force. The average shear yield stress of lead can be taken
boundary condition same differential equation.
2P
(R r )
as 4 N/mm2 [10 Marks]
P V0 . e h
Solution: R1 = 150 mm, h1 50 mm, R = ?, h = 25 mm, = 0.25
K 2P
(R R s )
Ftotal P
0
s
h
(R s r ) 2 Sr dr
RS
V 0 eh 2 Sr dr
V0 e h
K 2P
Ftotal
16
25
(170.25 r ) 2 Sr dr 4 3. e 25
2 Sr dr
ln (R R s ) 0 170.25
Answer:
S RIN2 H IN 2
S RFN H FN
2 2
or 200 u 50 RFN u 30 RFN 258.2 mm
200
and P 0.35 1 e 258.2 0.51
Now at Rss
Shear stress in sticking K = shear stress in sliding P Pss
2P
RFN Rss
or K = P 3Ke H FN
1 2P
or ln RFN Rss
3P H FN
H 1
or FN ln RFN Rss
2 P 3P
H 1 30 1
or Rss RFN FN ln 258.2 ln 254.55 mm
2P 3P 2 u 0.51 3 u 0.51
IFS-2012
Discuss Tresca and Von Mises yield criterion for metal forming operations. Also derive tensile and
shear yield stress relationships for their approaches. Which of this criterion is more realistic? Why?
[10 Marks]
Answer: Refer forging analysis
ANALYSIS
Y OF ROLLING Which
Whi h off the
th following
f ll i
IES 2001
assumptions
ti are correctt for
f
AssumptionsinRolling cold rolling?
1. Rolls are straight, rigid cylinders. 1. The material is plastic.
2 Strip is wide compared with its thickness,
2. thickness so that no 2. The arc of contact is circular with a radius g greater than
widening of strip occurs (plane strain conditions). the radius of the roll.
3. The
Th arc off contact is
i circular
i l withi h a radius
di greater than
h 3 Coefficient of friction is constant over the arc of
3.
contact and acts in one direction throughout the arc of
the radius of the roll.
contact.
contact
4. The material is rigid perfectly plastic (constant yield Select the correct answer using the codes given below: Considering the thickness of the element perpendicular to the
strength).
strength) plane of paper to be unity,
unity We get equilibrium equation in xx
Codes:
d
5. The coefficient of friction is constant over the tool direction as, - x h + ( x +d x ) (h + dh) - 2pR d sin
((a)) 1 and 2 ((b)) 1 and 3
workk interface.
f
(c) 2 and 3 (d) 1, 2 and 3 + 2 x R d cos = 0
For sliding friction, x = p Simplifying and neglecting Due to cold rolling, 0' increases as h decreases, 2Rd 2Rd 2d h
secondd order
d terms,
t i and
sin d cos = 11, we gett
I= h f + R
2
= h
= h/R = ln
R
thus 0' h nearly a constant and itsderivative zero.
d ( x h ) hf
Now h / R = + 2
d
= 2 pR ( ) d
d
( p / 0' )
2R
R
2 = ( ) or
d h
= 2
\
p x = 0 = 0' p /0 '
h d R
3
h = h f + 2 R (1 cos ) h f + R 2 2R
R
d
h ( p 0' ) = 2 pR ( )
II = h + R2
d
d d ( p / 0' )
f
2R
= ( ) d = h
2
d ' p
0 h ' 1 = 2 pR ( )
( p / )'
0
h f + R 2 f / R + 2
d
d h f + R 2 f + R
2
h R R h
( )
ln p / '0 = ln 2
R hf
.tan 1 . + ln C
y zone,, p = C. '0 o e Ho
In the entry hn H H h
. e ( 0 n ) = n . e Hn
hf R h0 hf
h R Ho ho
p = C '0 e H
and C = = e ( 0 n)
H 2H
R .e or
ho hf
R R
where H = 2 .tan 1 . h 1 1 h0
. e ( 0 )
H H
hf hf p = '0 or Hn = H0 ln
h0 2 h f
Now at entry , =
Hence H = H0 with replaced by in above equation I th
In the exit
it zone R R
From H = 2 .tan 1
.
At exit = 0 h hf
p = '0 .eH hf
Therefor p = '0
hf hf h f Hn
n = .tan .
At the neutral po int above equations R
R 2
will give same results and h n = h f + 2R (1 cos n )
For-2018 (IES,GATE & PSUs) Page 208 of 213 Rev.0
If back tension b is there at Entry,
Entry
h
IAS2012Main
p = ( o b ) . e ( 0 )
H H
IFS
IFS 2010
2010
h0
Calculate the neutral plane to roll 250 mm wide Whatis frictionhill ?
Whatis"frictionhill"?
If front tension f is there at Exit,
annealed copper
pp strip
p from 2.55 mm to 2.0 mm
h
p = ( o f ) . e H thickness with 350 mm diameter steel rolls. Take
hf
= 0.05 and o =180 MPa.
[10marks]
or B x (1 + B ) o = ( rC )
2B
IFS 2013
IFS2013 ANALYSIS OF EXTRUSION
B.C s at r = ro , x = b An a u u rod,
aluminium od, 6.
6.255 mm d a ete , iss d
diameter, aw into
drawn to For a round bar both wire drawingg and extrusion will ggive
1 a wire 5.60 mm diameter. Neglecting friction same equation except B.Cs
B b (1 + B ) o 2 B between the rod and the dies, dies determine the
C = drawing stress and the reduction in area when the B x (1 + B ) o = ( rC )
2B
ro yield
i ld stress
t f
for aluminium
l i i i 35 N/mm
is N/ 2. Also
Al
B.C s at r = rf , x = 0 (at exit stress is zero)
o (1 + B ) r 2 B
2B calculate the tangential stress at the exit. [8Marks]
r
or x = 1 + . b 1
Hint: Drawing Stress (1 + B ) o
o o
2B
C =
B r r
P A r
d = = o ln o = 2 o ln o rf
o (1 + B ) rf rf
2B 2B
Af A
f rf
Drawing stress ( d ) = 1 + . b
o (1 + B )
2B
For Tangential Stress i.e. Shear Stress
B ro ro x = Px = ( o x ) or x = 1 r
B rf
at Exit = P = ( o d ) = 0
For-2018 (IES,GATE & PSUs) Page 209 of 213 Rev.0
at r = ro
If effect of container friction is considered
o (1 + B )
2B
r
xo = 1 o p f = ram pressure required by container friction
B r
f i = uniform interface shear stress between
2
Ao ro billet and container wall
Extrusion ratio,, R = = for round bar
Af rf 2 i L
p f . r0 2 = 2 r0 i L or p f =
ro
h
= o Total Extrusion Pressure(Pt ) = xo + p f
for flat stock
h
f
and Extrusion Load = pt . r0 2
o (1 + B )
xo = 1 R 2 B
B
By: S K Mondal (GATE 99.96 Percentile) E-Mail: swapan_mondal_01@yahoo.co.in Page 1 By: S K Mondal (GATE 99.96 Percentile) E-Mail: swapan_mondal_01@yahoo.co.in Page 2
8. Design
a) Fluctuating Load Consideration for Design
b) Rolling Contact Bearings, Load-life Relationship
c) Sliding contact bearing, Modes of Lubrication, Sommerfeld Number
d) Clutch , Brake
9. Heat Transfer
a) Conduction
b) Critical Thickness of Insulation
c) Unsteady Conduction (Lumped Parameter Analysis)
d) Radiation (The Stefan-Boltzmann Law, Shape Factor Algebra, Heat Exchange between Non-
black Bodies)
e) Heat Exchangers (LMTD, NTU)
By: S K Mondal (GATE 99.96 Percentile) E-Mail: swapan_mondal_01@yahoo.co.in Page 3 By: S K Mondal (GATE 99.96 Percentile) E-Mail: swapan_mondal_01@yahoo.co.in Page 4
who are attending coaching x Thermodynamics {Book Rajput + P K Nag Unsolved all (My solutions available)}
x Fluid Mechanics & Machines (Book Bansal or Rajput or my book + Only 20 Years GATE
x Attend all classes.
Questions, My set)
x Meticulously read class notes
x Heat Transfer (Book Rajput or Domkundwar + Only 20 Years GATE Questions, My set)
x From the question set solve all previous year asked questions which are given in topic wise
x Design (Book Bhandari or Khurmi + Only 20 Years GATE Questions, My set)
sequence.
x RAC (Book Rajput or CP Arora+ Only 20 Years GATE Questions, My set)
x It is recommended to solve my question set on your own and then cross check with my
x Power plant (Book PK Nag + Only 20 Years GATE Questions, My set)
explanations.
x IC Engine (Book V Ganeshan + Only 20 Years GATE Questions, My set)
x Mathematics (Class note + My Question set)
x Engineering Materials (NPTEL IISc material from net + Only 20 Years GATE Questions, My
x Manufacturing Science (Class note + My Question set GATE,IES,IAS)
set)
x SOM (Class note + My Question set GATE,IES,IAS)
By: S K Mondal (GATE 99.96 Percentile) E-Mail: swapan_mondal_01@yahoo.co.in Page 5 By: S K Mondal (GATE 99.96 Percentile) E-Mail: swapan_mondal_01@yahoo.co.in Page 6