Professional Documents
Culture Documents
Signature ISX, and QSX15 - Overhead - Set PDF
Signature ISX, and QSX15 - Overhead - Set PDF
Overhead Set
(003-004)
Measure
General Information
Page 1 of 14
9/04/09 10:11 AM
Remove the oil fill connector from the lower gear case
cover.
WARNING
Do not pull or pry on the fan to manually rotate the
engine. To do so can damage the fan blades.
Damaged fan blades can cause premature fan
failures which can result in serious personal injury
or property damage.
Page 2 of 14
9/04/09 10:11 AM
Injector
and Valve
Adjustment
Sequence
Bar Engine
Set Set Set
in Pulley
Cylinder Cylinder Cylinder
Direction Position
Injector Valve Brake
of Rotation
Start A 1 1 1
Advance to B 5 5 5
Advance to C 3 3 3
Advance to A 6 6 6
Advance to B 2 2 2
Advance to C 4 4 4
Page 3 of 14
9/04/09 10:11 AM
Firing
Order: 1-5-
3-6-2-4
Valve Lash
Page 4 of 14
9/04/09 10:11 AM
Injector Lash
Adjust
Page 5 of 14
9/04/09 10:11 AM
Remove the oil fill connector from the lower gear case
cover.
WARNING
Do not pull or pry on the fan to manually rotate the
engine. To do so can damage the fan blades.
Damaged fan blades can cause premature fan
failures which can result in serious personal injury
or property damage.
Page 6 of 14
9/04/09 10:11 AM
engine (1-2-3-4-5-6).
Injector
Page 7 of 14
9/04/09 10:11 AM
and Valve
Adjustment
Sequence
Bar Engine
Set Set Set
in Pulley
Cylinder Cylinder Cylinder
Direction Position
Injector Valve Brake
of Rotation
Start A 1 1 1
Advance to B 5 5 5
Advance to C 3 3 3
Advance to A 6 6 6
Advance to B 2 2 2
Advance to C 4 4 4
Firing
Order: 1-5-
3-6-2-4
Page 8 of 14
9/04/09 10:11 AM
Make sure the parts are aligned, and squeeze the oil
out of the valve and injector train by tightening the
adjusting screw.
Page 9 of 14
9/04/09 10:11 AM
With the set mark aligned with the pointer on the gear
cover and both sets of valves closed on the cylinder,
loosen the locknuts on the intake and exhaust valve
adjusting screws.
Page 10 of 14
9/04/09 10:11 AM
CAUTION
To get maximum brake operating efficiency and to
prevent engine damage, the brake adjustment
instructions must be followed.
The set marks are BRAKE SET 1-6, and BRAKE SET
2-5, and BRAKE SET 3-4.
Page 11 of 14
9/04/09 10:11 AM
Page 12 of 14
9/04/09 10:11 AM
CAUTION
Engine damage can occur if the running clearance is
not within specifications.
Page 13 of 14
9/04/09 10:11 AM
Injector
and Valve
Adjustment
Sequence
Bar Engine
Set Set Set
in Pulley
Cylinder Cylinder Cylinder
Direction Position
Injector Valve Brake
of Rotation
Start A 1 1 1
Advance to B 5 5 5
Advance to C 3 3 3
Advance to A 6 6 6
Advance to B 2 2 2
Advance to C 4 4 4
Firing
Order: 1-5-
3-6-2-4
Page 14 of 14