Professional Documents
Culture Documents
sided adhesive tape 9098 has strong adherence due to its acrylic adhesive specifically modified for high
performances. The bond is immediate, the double sided adhesive 9098 tape has a fast and resistant hold.
The tape is recommended for general outdoor and indoors use, due to its high capacity to stand strong even in
high temperatures and solvents. With a width of 12, 19 and 25 mm and a length of 50 meters roll, band can be
used on a variety of materials.
Transparan, tahan terhadap radiasi UV dan suhu konstan yang tinggi lebih dari 90 derajat Celsius, pita perekat
dua sisi 9098 memiliki ketaatan yang kuat karena perekat akriliknya dimodifikasi khusus untuk pertunjukan
tinggi. Ikatannya langsung, pita perekat 9098 berpotongan ganda memiliki pegangan yang cepat dan tahan.
Rekaman ini direkomendasikan untuk penggunaan di luar ruangan dan di dalam ruangan umum, karena
kapasitasnya yang tinggi untuk berdiri tegak bahkan pada suhu dan pelarut tinggi. Dengan lebar 12, 19 dan 25
mm dan panjang roll 50 meter, band bisa digunakan pada berbagai bahan.
Designed for temporary use, some 3M double-sided tapes are easy to reposition or remove.
Others, however, are problematic. After exposure to heat and UV rays for long periods, the
adhesive dries out, making it difficult to remove from glass, plastic, or painted surfaces.
While a razor blade scrapes the adhesive off glass, there are a number of products
formulated to remove adhesives from fragile surfaces. Before applying any product to
remove the adhesive, test a small area to ensure that it does not damage the original surface.
Try Heat
Heat affects some 3M tape adhesives. Try using a blow drier to heat and soften the
adhesive. Insert a plastic putty knife under the edge of the tape to lift and peel it off the
paint, plastic, or glass.
Add Moist Heat
Moist heat, such as a steam iron, may dissolve the tape adhesive. Alternately, place a wet
rag over the tape adhesive and use a blow drier or iron to heat the rag. Scrub the surface
gently with the rag to peel off the adhesive. Use caution on plastic and paint; the surface
may be damaged by the hot water.
Use a Solvent
Test a small area of the original surface in an inconspicuous location before using any
solvent or alcohol product. A solvent or alcohol may damage the surface.
Try 3M Adhesive Remover
When removing a 3M adhesive, try using a 3M product designed for that purpose. 3M
adhesive remover is safe for use on cured automotive paint, vinyl, and glass. It also
removes grease, oil, and wax.
Soak It with WD-40
The mechanic's best friend, WD-40, is not just a lubricant. WD-40 contains petroleum
products, which work as an adhesive solvent. Spray the tape or any lingering adhesive
residue with WD-40 and allow it to soak for several minutes. On a vertical surface, cover
the adhesive with a rag or paper towel soaked in WD-40. Hold it in place for a few minutes,
or tape plastic wrap over the rag to hold it in place. Use a plastic putty knife to scrape the
adhesive off the surface, and then wipe any remnants off with a rag. Clean the area with
soap and water to remove any remaining WD-40.
Get Some Goo Gone
Sold in small bottles, Goo Gone dissolves tape adhesive. Spread the Goo Gone over the
tape adhesive and allow it to soak in for several minutes. Wipe the tape residue off with a
rag. Goo Gone leaves an oily residue that dishwashing liquid, such as Dawn, easily
removes.
Use a Little Alcohol
Rubbing alcohol or hand sanitizer with alcohol also dissolves tape adhesive. Use cotton
balls or swabs to apply alcohol to the adhesive. If necessary, pour some of the product onto
a paper towel or rag and place it over the adhesive. Cover the paper towel or rag with
plastic wrap and tape it down. After a few minutes, lift the edge of the plastic and check the
adhesive. If it has softened, remove the plastic and use the rag to wipe off the adhesive.
Dirancang untuk penggunaan sementara, beberapa tape double-sided 3M mudah diposisikan atau dihapus. Yang
lainnya, bagaimanapun, bermasalah. Setelah terpapar panas dan sinar UV dalam waktu lama, perekat
mengering, sehingga sulit dikeluarkan dari kaca, plastik, atau permukaan yang dicat. Sementara pisau cukur
menggores kaca perekat, ada beberapa produk yang diformulasikan untuk menghilangkan perekat dari
permukaan yang rapuh. Sebelum menerapkan produk apapun untuk melepaskan perekat, uji area kecil untuk
memastikan tidak merusak permukaan aslinya.
Cobalah Panas
Panas mempengaruhi beberapa perekat tape 3M. Coba gunakan blow drier untuk memanaskan dan
melembutkan perekat. Masukkan pisau dempul plastik di bawah tepi pita untuk mengangkat dan mengelupas
dari cat, plastik, atau kaca.
Gunakan Pelarut
Uji area kecil permukaan asli di lokasi yang tidak mencolok sebelum menggunakan produk pelarut atau alkohol.
Pelarut atau alkohol dapat merusak permukaan.