Professional Documents
Culture Documents
PA Probe Update WPS - en PDF
PA Probe Update WPS - en PDF
WPS FEATURES
WEDGE FEATURES
Probe Evolution
As a world leader in phased array (PA) probe manufacturing, Olympus NDT has once again
proved its superior applications knowledge with the introduction of the all new PA Weld
Probe Series. Addressing multiple improvement opportunities, this new series will raise our
best selling A1 and A2 probes to a new level. Every aspect of the probes has been exam-
ined and optimized for more inspection possibilities and a better ergonomic design. The
smaller housing and wedge footprint allow closer access to the feature being inspected for
a better beam coverage. The improved ergonomics make the probe more comfortable to
hold during manual inspections. Because automated inspections are becoming more and
more important, the cable exit has been optimized in order to reduce any conflict with
holders once a probe is mounted on a scanner.
IHC RING
An optional IHC ring is now of-
fered on all A10, A11, and A12
probes. This removable ring is
attached to the wedge when
automated inspection is desired.
920-143B-EN
EXAMPLE OF BEAM COVERAGE ADVANTAGE WITH NEW A10 PROBE VS. THE A1 STYLE PROBE
Distance from first element to 28.6 mm 20.6 mm
front of the wedge 1.13 in. 0.81 in.
The optimized wedge design of the new
Weld Probe Series allows the user to
get closer to the weld. For some appli-
cations, this provides the ability to fire
directly on the defect instead of using
multiple skips before reaching the heat
affected zone.
The A10 probe is shown with the op-
tional IHC ring.
A1 probe A10 probe
with SA1-N60S with SA10-N55S
PROBES
Active Dimensions in mm (in.)
Number of Elevation
Part number Frequency Pitch aperture
elements (mm) L W H
(mm)
5L16-A10 5.0 16 0.60 9.6 10.0 15.6 (0.62) 22.5 (0.89) 20 (0.79)
10L32-A10 10.0 32 0.31 9.9 7.0 15.6 (0.62) 22.5 (0.89) 20 (0.79)
5L32-A11 5.0 32 0.60 19.2 10.0 25.1 (0.99) 22.5 (0.89) 20 (0.79)
5L64-A12 5.0 64 0.60 38.4 10.0 44.6 (1.76) 22.5 (0.89) 20 (0.79)
WEDGES
REPLACEMENT PROBES
New probe Replaces* Typical applications General application
5L16-A10 5L16-A1
Pipe or tube weld inspection, mid wall (5mm to 50mm)
10L32-A10 10L32-A1 Detection of flaws and sizing
Single channel sector scan inspections machined and structural
5L32-A11 5L64-A2 components for cracks
Pipe or tube weld inspection, mid wall (5mm to 200mm)
Multiple channel sector and linear scan inspections
5L64-A12 5L64-A2
Pipe or tube weld inspection, mid wall (5mm to 100mm)
*Probes that are replaced by the new series will be offered for a limited time.
is ISO 9001 certified.
www.olympus-ims.com
Stock Road, Southend-on-Sea, Essex, SS2 5QH, UK, Tel.: (44) (0) 1702 616333
450 Campbell St. Unit 5, Cobourg, Ontario K9A 4C4, Tel.: (1) 905-377-9611
info@olympusNDT.com
31 Gilby Road, Mount Waverly, Victoria, 3149, Tel.: (61) 130-013-2992