Professional Documents
Culture Documents
Review Notes
Review Notes
SET ONE
2. Which of the ff. bituminous material is best recommended for sealing weakened plane joints?
Ans. joint filler asphalt (commonly called hard asphalt or blown asphalt)
3. The main problem associated with wrong practice of conveying concrete is called what?
Ans. segregation
4. The specifications call for 1:2:4 concrete mix. In a one bagger mixer, which of the ff. amount of water is most likely
required for the mix?
Ans. - 20 liters
5. A one-lane road, with a pavement width of 3.5 meters and shoulder width of 0.5 meter on each side of the pavement, was
designed to have sub base and base courses with a combined thickness of 300mm. If the thickness of the sub base is a
125mm, the spreading and compaction of the subbase and base courses shall be carried out in:
Ans. 3 layers over the full width of 4.5 m
6. As materials engineer, what is the area of the trial section that you would recommend to check the suitability of the
materials and efficiency of the equipment to be used for item 310 Bituminous Concrete Surface Course?
Ans. about 500 sq.m
7. Per program of work, the estimated volume of Item 201 materials is 7500 cu.m. How many grading and plasticity tests are
required based on the DPWH minimum testing requirements?
Ans. 25 grading and 25 plasticity
9. Quality of factory-produced reinforced concrete pipes may be best establishment through what?
Ans. Test of concrete pipes samples
10. Where do we take additional cores when the measured of any core taken from the pavement is deficient in thickness by
more than 25mm?
Ans. at no less than 5 meter intervals parallel to the centerline in each direction from the affected location
11. The results of the Immersion-Compression test conducted on an asphalt mix sample are as follows:
Dry stability = 2,000 Kpa
Wet stability = 1,000 Kpa
What is the resulting Index of Retained strength? Does it meet the specification requirement of Item 301, Bituminous
Concrete Surface Course?
Ans.
Index of Retained Strength or IRS = Wet stability x 100
Dry stability
= (1,000 Kpa/2,000 Kpa) x 100
IRS = 50%
* No, it does not meet the specification of Item 310 since the specification
of IRS is 70% minimum while the resulting IRS here is only 50%.
13. As materials engineers, when is the right time to start sampling and testing aggregate of the course materials?
Ans. Before the course materials be incorporated in the project.
15. Under what climatic condition(s) do we use the lower penetration grade or hard asphalt?
Ans. hot climate
16. Sampling of the freshly mixed concrete should be taken on the ______ batch discharge of the transit mixer?
Ans. - middle
17. Soft and unstable soils were encountered during the course of sub-grade preparation. If you were the materials engineer
assigned to the project, what is the most effective and cheaper method that you would recommend to stabilize the soil prior
to the construction of the subbase course?
Ans. - geotextiles
18. How many times per layer should a concrete specimen molded in a 6x6x12 beam mold be rodded?
Ans. 63 times
19. What is the basis for acceptance or rejection of any construction materials?
Ans. Materials Test Reports
20. In testing concrete cylinder sample the load applied should be continuous without shock at a constant rate within the range
of _______ per second.
Ans. - 0.14 to 0.34 Mpa per second or 20 to 50 psi per second.
21. During the application of the first half of the anticipated load a loading shall be permitted.
Ans. higher rate
22. Initial rolling in bituminous mixes shall be performed with a ___________ roller.
Ans. Pneumatic-Tire roller
23. Final rolling in bituminous mixes shall be performed with a ____________ roller.
Ans.- 3-wheel or tandem type steel wheel roller
24. Rolling of Bituminous mix shall be discontinued whenever it begins to produce excessive __________or __________.
Ans.- pulverizing of the aggregate or displacement of the mixture
25. Final rolling shall be continued until roller marks are eliminated and a minimum _________ mass percent of the density of
the laboratory compacted a specimen prepared in accordance with AASHTO T160 has been obtained.
Ans. 95 mass percent
26. Sample from compacted bituminous mix shall be neatly cut by a saw or core drill. Each sample shall be at least
___________.
Ans. 150mm x 150mm x 100mm diameter full depth
27. For surface Tolerances the surface (bituminous mix) will be checked by the used of a __________ at sites selected by the
engineer.
Ans. 3-m straight edge
28. If the volume of coarse aggregate intended in your project in 85 cu.m., how many grading test will you perform?
Ans. - 1 grading test
29. What is the most common method adapted by DPWH in the determination of density of the soil in place?
Ans. sand cone method
30. What is the minimum sample for moisture content determination if the maximum size of particles is 50mm (2 inches)?
Ans. 1000 grams
31. What is the minimum mass of field sample for a maximum size of fine aggregates at 4.75mm (no.4)?
Ans. 20 kgs.
32. What is minimum mass of field samples for coarse aggregate with a maximum nominal size of aggregates of 50mm (2
inches)?
Ans. 75 kgs.
33. What is the minimum mass/quality of samples for Portland cement to be tested for quality test in the laboratory?
Ans. 10 kgs.
36. The submission of any type of samples in the laboratory, what should you accomplished and to be submitted together with
the samples?
Ans. sample card
37. If the minimum yield strength of a grade 40 steel bars is 40,000 psi, what is the equivalent MN/m2?
Ans. 276 Mpa
38. If the minimum yield strength of a grade 60 steel bars is 414 Mpa, what is the equivalent in PSI?
Ans. 60,000 psi
39. How many samples for quality of steel bars grade 40 if there are 15,500 kgs. of steel bars all 25mm 0 at site?
Ans. 2 samples @ 1 meter long
40. What is the minimum mass of yield samples for coarse aggregates with a maximum nominal size of aggregate of 75mm
(3inches)?
Ans. 100 kgs.
41. What is the minimum mass of coarse aggregates retained on the 200mm sieve shall be set a side for sieve analysis for
50mm (2 inches) particle size?
Ans. 2 kgs.
42. What is the minimum average strength requirement for non load bearing concrete hollow blocks?
Ans. 4.14 Mpa.
43. What is the minimum average strength requirement for a load bearing concrete hollow blocks?
Ans. 6.9 Mpa.
44. What is the average deficient thickness per lot of cores specimen where no payment is recommended on the project?
Ans. more than 25 mm
45. What is the maximum average deficient thickness per lot of cores specimen where 100% payment is recommended?
Ans, - 5 mm maximum
46. Concrete in the area represented by the cores will be consider adequate if the average strength of the cores is equal to at
least ________ of the specified strength, fc and no single core is less than 75% of fc.
Ans. 85% fc
47. The weighted loss of fine aggregates subjected to 5 cycles of the sodium sulfate soundness test should not exceed.
Ans. 10 mass %
48. The recommended type of Portland cement to be used in concreting unless otherwise provided for in the special provision:
Ans. type 1
50. Fine aggregates shall be rejected when if fails in the ________ for organic impurities.
Ans. colormatic test
51. Fine aggregates used for PCCP shall not contain more than ________ of materials passing the 0.075 mm (no. 200 sieve) by
washing.
Ans. 3 mass percent
52. The coarse aggregate used for PCCP shall not contain more than ________ of materials passing the 0.075 mm (no. 200
sieve) by washing.
Ans. 1 mass percent
53. The mass percent of wear or abration loss of coarse aggregate used for when by AASHTO T-96 should not exceed.
Ans. 50%
54. The weighted loss of coarse aggregate when subjected to five (5) cycle of the sodium sulfate soundness test should not
exceed.
Ans. 12 mass percent
56. A department Order series of 1997 give supplement guidelines on the conduct of Project assessment by the Quality
assurance units Regional Office (QAU-RO)
Ans. D.O. #52
57. A Department Order series of 1997, Revised DPWH Standard specification for Elastomeric bearing pads for bridge
superstructures.
Ans. D.O. #20
58. What is the maximum compressive strength of 150 mm x 300 mm concrete cylinder specimen at 28 days for class B
concrete?
Ans. 5000 Psi (37.7 Mpa)
59. What is the maximum compressive strength of 150 mm x 300 mm concrete cylinder specimen at 28 days for class C
concrete?
Ans. 3000 Psi (20.7 Mpa)
60. The weepholes shall be placed at the lowest points where free outlets for water can be obtained and shall be spread not
more than:
Ans. 2 meters center to center
61. One of the most common method used in compaction test/moisture density relation test of soil is:
Ans. AASHTO T-180
62. Which of the ff. common method used in compaction test/moisture density relation test of soil adopted by DPWH:
Ans. AASHTO T-99 and AASHTO T-180
63. If you are to use AASHTO T-99 method (standard proctor test) in compaction test, what is the weight of rammer to be
used?
Ans. 2.5 kgs. (5.5 lbs.)
64. Using the standard proctor test or AASHTO T-99, what is the height of drop to a free fall above the elevation of the soil and
uniformly distributes such drops to the soil surface?
Ans. 305 mm (12)
65. Using the standard Proctor test or AASHTO T-99 or moisture density relation test, what is the recommended no. of blows
per layer?
Ans. 25 blows
66. Using the modified Proctor test (AASHTO T-180) method for moisture density relation test of soil, what is the recommended
no. of blows per layer?
Ans. 56 blows
67. Using again the modified Proctor test ( AASHTO T-180) method for moisture density relation test of soil, what is the height
of drop to a free fall above the elevation of the soil and uniformly distributes such drops to the soil surface?
Ans. - 457 mm (18)
68. What is the capacity or the computed volume of mold using 6 (152 mm) mold for both AASHTO T-99 & AASHTO T-180
method?
Ans. 0.002124 m3
69. What are the datas needed in moisture density relation test of soil 2 most common method?
Ans. maximum dry density (MDD)
- optimum moisture content (OMC)
70. The prime coat shall be left undisturbed for a period of at least ________ hrs. and shall not be opened to traffic until it has
penetrated and cured sufficiently so that it will not be picked up by the wheels for passing vehicles.
Ans. - 24 hrs.
72. Stockpiles of concrete aggregates shall be built-up in layers of not more than in thickness.
Ans. one (1) meter
73. All washed aggregates shall be stockpiled or binned for draining at least ________ hrs. before being batched.
Ans. 12 hrs.
74. Concrete not in place within ________ from the time the ingredients where charged into the mixing drum or that has
developed initial set shall not be used.
Ans. 90 minutes
75. Shall not be painted or coated with asphalt or other materials or enclosed in tubes or sleeves.
Ans. tie bars
76. Mortar that is not used within ________ after the water has been added shall be discarded.
Ans. 90 minutes
77. The maximum tensile strength of the wire mesh for gabions shall be
Ans. 586.1 Mpa
81. Sampling of PCCP/asphalt core specimens shall be taken from the pavement using:
Ans. core drill
82. Size of asphalt core specimen for thickness and density determination:
Ans. at least 150 mm x 150 mm
- 100 mm diameter full depth
83. The diameter of asphalt core specimens shall be at least equal to:
Ans. one and one half times the maximum size of aggregates
84. The thickness of asphalt core specimens shall be at least equal to:
Ans. two (2) times the maximum size of aggregates
85. Obtaining asphalt core specimens for each full days operation shall be:
Ans. at least one but not more than three (3) core samples
88. The average of ________ measures are made on the asphalt core specimens in determining the thickness.
Ans. 4
89. In bituminous mixture, ________ will not be permitted as a method of measurement.
Ans. batch weights
90. A core shall be taken for every ________ if no core was taken at the end of each days operation.
Ans. 100 Lm per lane
91. The average of four (4) measurements on the asphalt core specimen is to determine the
Ans. thickness
92. The computation for the quantity of bituminous mixture area the ff.
Given:
Paving length represented, m = 120
Thickness, cm = 5.0
Width, m = 3.05
Total length of pavement, m = 380
Density, gm/cm3 = 2.221
Ans. 40.64 tons
93. Main constituents of asphalt which is found in nature or as a residue in petroleum refining.
Ans. bitumen
98. Representative quantity of one sample in sampling liquid asphalt is ________ sample for every:
Ans. 1 quart to 1 gallon
99. During the breakdown rolling of asphalt mix, it is carried out by:
Ans. pneumatic roller
100. In rolling asphalt mix, what phase of rolling is to remove the marks by the
other roller?
Ans. final rolling
103. The mixture of item 231 shall have a mass percent air voids with range of ________.
Ans. 3 to 5
104. A consistency test for solid asphalt that determines the hardness of asphalt.
Ans. Penetration
105. Determines the purity of asphalt on how much bitumen is in the asphalt.
Ans. asphaltane
106. The properties of asphalt depend upon this ________ substance which is soluble in petroleum solvents.
Ans. Petrolane
111. The objective is to determine as economical blend between graded aggregates and asphalt in order to produce a
pavement that would meet the required specification.
Ans. Job mix formula
112. Asphalt cement with water and a little amount of emulsifier, usually derivatives of salt.
Ans. Emulsified Asphalt
113. Asphalt cement mixed with kerosene, black in color and liquid and room temperature.
Ans. Medium Curing Cut back Asphalt
114. Test specimen required for Item 311 Portland Cement Concrete Pavement.
Ans. Concrete beam
116. Forms for PCCP shall remain in place undisturbed for not less than ________ hrs. after concrete pouring.
Ans. 24
119. Transverse construction joint is also called as ________ is constructed when there is an interruption of more
than 30 minutes in the correcting works.
Ans. cold joint
120. Mixing time of PCCP shall not be less than ________ or more than _______
Ans. five (5) seconds, ninety (90) minutes
123. Depth of weakened plane joints should at all times not be less than _______.
Ans. 50 mm
124. Bars placed perpendicular to the longitudinal joint of PCCP.
Ans. tie bars
125. Vibrators shall not be operated longer than ________ in any one location.
Ans. 15 minutes
126. Flexural strength of PCCP when tested at mid-point.
Ans. 4.50 Mpa
127. Sawing of joints of PCCP shall commence as soon as the concrete has hardened sufficiently, usually ________.
Ans. within 24 hrs.
128. The surface of the newly placed PCCP shall be cured for a period of
________.
Ans. 72 hrs.
129. Used as load transfer device and are held in-position parallel to the centerline of the slab.
Ans. dowels
131. Straw curing on PCCP shall be at least ________ thick which is measured after wetting.
Ans. 20 cm.
132. The finished product of mixing aggregates with cement and water.
Ans. concrete
133. Rate of increase in strength is ________ at high temperature than at low temperature.
Ans. higher
134. Most specifications for concrete exposed to weathering require that water-cement ratio be ________ by weight.
Ans. 0.53
135. Physical property of concrete that withstand deterioration due to exposure to weathering action.
Ans. durability
136. Over sanded and under sanded mixtures require more water in order to be workable, but making it so will, only
result in a sacrifice in:
Ans. strength
138. The new method used to test on workability of concrete and these tests are readily made in the field.
Ans. slump test
139. For rich mixes, the strength of ________ is the controlling factor.
Ans. aggregates
142. Class of concrete used for pre-stressed concrete structure and its member.
Ans. Class P
143. Class of concrete used in footings, missive pier shafts and unreinforced or with only a small amount of
reinforcement.
Ans. Class B
146. One (1) Sieve Analysis for every ________ of concrete aggregates or a fraction thereof:
Ans. 1,500 m3
147. A minimum weight of ________ sample shall be taken from each 2,000 bags of cement or fraction thereof.
Ans. 10 kg.
148. Class of concrete used to all superstructures and heavily reinforced substructures.
Ans. Class A
REVIEW QUESTIONAIRE:
2. The depth of the weakened plain joint should at all times not less than:
Ans. 50 mm
3. Serves as load transfer device and are held in position parallel to the surface and center line of the slab by a metal device:
Ans. dowel
6. The flexural strength of the concrete beam sample at 14 days when tested at third point method:
Ans. 3.8 Mpa
9. The practice of artificially densifying and incorporating and incorporating definite density into the soil mass rolling,
tampering or other means:
Ans. compaction
10. The unit pressure greater than which progressive settlement will occurs leading o failure:
Ans. bearing capacity
11. Specified or selected materials of designed thickness placed as foundation for pavement.
Ans. - base
12. The materials in excavation (cuts) embankment (fills) and embankment foundation immediate below the layer of subbase,
base or pavement and to such depth as may effect the structural design:
Ans. sub-grade materials
13. Specified or selected materials of designed thickness placed as a foundation for base:
Ans. subbase
14. A widely used as control test in embankment construction to ensure adequate compaction:
Ans. field density test
17. What are the essential laboratory test for soil classification:
Ans. grading plastic and liquid limit test
18. Provided along the slopes of high embankments as an erosion control measure and to improve the stability of the side
slopes;
Ans. berm
19. What is the oven drying temperature for moisture content determination:
Ans. 110 C + 5
21. The primary quality control mechanism for the production of asphalt mixture:
Ans. job-mix formula
22. The most commonly used method in the design and evaluation of bituminous concrete mixes:
Ans. Marshall Stability Method
23. The most common method in determining the consistency of concrete mix:
Ans. slump test
26. A layer of an asphalt aggregate mixture of variable thickness used to eliminate irregularities in the content of an existing
surface prior to placement of an overlay:
Ans. asphalt leveling course
27. An application of low-viscosity cutback to an absorbent surface or a mixed-in application of emulsified asphalt. It is used
only on untreated base prior to placement of an asphalt pavement.
Ans. asphalt prime coat
28. A thin asphalt surface treatment used to waterproof and improve the texture of an asphalt wearing surface.
Ans. - asphalt surface treatment
29. The upward movement of asphalt in an asphalt pavement resulting in the formation of a film of asphalt on the surface.
Ans. bleeding flushing asphalt
30. An application of asphalt materials to any type of road or pavement surface with or without a cover of mineral aggregates
that produce an increase in thickness of less than 25mm or 1 inch.
Ans. asphalt surface treatment
31. The localized buckling or shattering of a rigid type pavement occurring usually at transverse crack or joint.
Ans. blow-up
32. A very light application of asphalt applied to an existing asphalt or Portland cement surface, used to ensure a bond between
the surface of being paved and the overlaying course.
Ans. asphalt tack coat
33. A mixture of slow setting emulsified asphalt, water, aggregates and mineral filler produce to a slurry consistency and placed
on pavement surface.
Ans. asphalt emulsion slurry seal
34. The separation of the pavement due to natural causes, traffic action or reflections from an underlying pavement.
Ans. crack
35. The bowl-shape holes of varying sizes in the pavement, resulting from localized disintegration.
Ans. potholes
36. A crack in asphalt overlay that reflects the crack pattern in the pavement structure underneath.
Ans. reflective cracks
37. The progressive separation of aggregate particles in a pavement from the surface downward or from the edge inward.
Ans. raveling
38. A crack sometimes crescent shaped, that point in the direction of the trust of the wheels on the pavement surface caused by
lack of bond between two pavement layer.
Ans. slippage cracks
45. The soaked CBR value for Item 201(base course) at maximum dry density is:
Ans. not less than 80%
46. The mass percent of wear of course aggregates for base materials by Los Angeles Abrasion Test.
Ans. not more than 50 %
47. The stones used for stone masonry shall have a thickness of not less than:
Ans. 150mm
49. The temperature for moist curing of specimen that gives the best result.
Ans. 15.5 C to 37.5 C
50. The maximum size to course aggregates required for Item 311 (PCCP)
Ans. 2 inches (63mm)
51. A program of quality control works to be complied by the contractor is prepared by DPWH.
Ans. quality control program
52. Prescribed in each project based on estimated quantities. The requirements specify the kind and number of test for each
item of works.
Ans. minimum testing requirements
53. Memorandum Circular No. hereby directed that all materials men incharge in a said project keep a logbook on materials
quality control.
Ans. MC #80
54. A department order hereby directed that only test report issued by the regional/district laboratories of the department and
other testing laboratories accredited by the DPWH shall be allowed to be used in the acceptance or rejection of construction
materials.
Ans. D.O. # 135
55. A department order, hereby directed, no acceptance and final payment shall be made on completed concrete and asphalt
pavements unless core test for thickness determination is conducted.
Ans. D.O. # 119
58. A test covers the quantitative determination of bitumen in hot mixed paving mixtures and pavement samples for
specification acceptance, service evaluation, control and research.
Ans. extraction test
59. The permitted variations in design requirements of aggregates subbase materials on surface irregularity measured by a 3m
straight edge.
Ans. 20mm
60. The permitted variations in design requirements of aggregates base materials on cross fall or camber.
Ans. 0.20%
61. If the required thickness for subbase or base is 150mm or less, this maybe spread and compacted in.
Ans. 1 layer
63. The maximum sieve opening for grading requirement of aggregate base course.
Ans. 50mm
64. The bituminous prime coat materials should be applied by a pressure distributor at specified temperature and at an
application rate ranging from:
Ans. 1 to 2 liters / sq.m.
65. The rate of application for bituminous tack coat materials (item 302) ranging from:
Ans. 0.2 to 0.7 liters / sq.m.
66. The P.I. for mineral filler used for Hot Plant Mix Bituminous Pavement:
Ans. not greater than 6
67. The gradation requirement used for Hot Mix Bituminous Pavement.
Ans. grading d
68. The placing temp. for bituminous mixture measured in the truck prior to dumping.
Ans. should not be less than 107 C
69. How many samples or core drilled samples be taken for each days full operation.
Ans. at least one, but not more than 3
71. Unsuitable materials are soils with natural water content exceeding.
Ans. 80
72. Materials containing detrimental quantities of organic material such as grass, roots, sewerage highly organic soils such as
peat and muck.
Ans. unsuitable materials
73. The fraction passing the 0.425mm (No.40) sieve for Item 200 shall have a liquid limit of:
Ans. not greater than 35
74. The fraction passing the 0.425mm (No.40) sieve for Item 104 shall have a liquid limit of:
Ans. not greater than 30
75. The fraction passing the 0.425mm (No.40) sieve for Item 201 shall have a liquid limit of:
Ans. not greater than 25
76. The fraction passing the 0.425mm (No.40) sieve for Item 202 shall have a liquid limit as determined by AASHTO T-89
Ans. not greater than 25
77. The fraction passing the 0.425mm (No.40) sieve for Item 200 shall have a plasticity index of:
Ans. not greater than 12
78. The fraction passing the 0.425mm (No.40) sieve for Item 201 shall have a plasticity index of:
Ans. not greater than 6
79. The fraction passing the 0.425mm (No.40) sieve for Item 202 shall have a plasticity index of:
Ans. not greater than 6
80. The coarse portion, retained on a 2.00mm (No.10) sieves for Item 201 shall have a mass percent of wear by the Los
Angeles Abrasion Tests as determined by AASHTO T96.
Ans. not exceeding 50
81. The coarse portion, retained on a 2.00mm (No.10) sieves for Item 201 shall have a mass percent of wear by the Los
Angeles Abrasion Tests.
Ans. not exceeding 50
82. The materials passing the 19mm sieves for Item 202 shall have a soaked CBR value tested according to AASHTO T-193.
Ans. 25% minimum
83. The materials passing the 19mm sieves for Item 201 shall have a soaked CBR value tested according to AASHTO T-193.
Ans. 80% minimum
84. The materials passing the 19mm sieves for Item 202 shall have a soaked CBR value of:
Ans. 80% minimum
85. The coarse portion, retained on a 2.00mm (No.10) sieves for Item 202 shall have a mass percent of wear by the Los
Angeles Abrasion Tests of:
Ans. not exceeding 4
ASPHALT TECHNOLOGY
3. A layer of an asphalt aggregate mixture of variable thickness used to eliminate irregularities in the cement of an existing
surface prior to placement of an overlay.
Ans. asphalt leveling course
4. An application of low-viscosity cutback to an absorbent surface, or mixed in application of emulsified asphalt. It is used only
on untreated base prior to placement of an asphalt pavement.
Ans. asphalt prime coat
5. A thin asphalt surface treatment used to waterproof and improve the texture of an asphalt wearing surface.
Ans. asphalt seal cost
6. The upward movement of asphalt in an asphalt pavement resulting in the information of film of asphalt on the surface.
Ans. bleeding of flushing asphalt
7. An application of asphalt materials to any type of road or pavement surface with or without a cover of mineral aggregates
that produce an increase in thickness of less than 25mm or 1 inch.
Ans. asphalt surface treatment
8. The localized buckling or shattering of a rigid type pavement, occurring usually at transverse crack or joint.
Ans. blow-up
9. A very light application of asphalt applied to an existing asphalt or Portland cement surface, used to ensure a bond between
the surface of being paved and the overlaying course.
Ans. asphalt track coat
10. The separation of the pavement due to natural causes, traffic action, or reflections from an underlaying pavement.
Ans. crack
11. The bowl-shape holes of varying sizes in the pavement, resulting from localized disintegration.
Ans. potholes
12. A crack in asphalt overlays that reflects the crack pattern in the pavement structure underneath.
Ans. reflective cracks
13. The progressive separation of aggregate particles in a pavement from the surface downward of from the edge inward.
Ans. raveling
14. A cracks sometimes crescent shaped that point in the direction of the trust of the wheels on the pavement surface caused
by lack of bond between two pavement layers.
Ans. slippage cracks
16. A department Order, hereby directed, No acceptance and final payment shall be made on completed concrete and asphalt
pavement unless core test for thickness determination is conducted.
Ans. DO # 119
18. A test covers the quantitative determination of bitumen in hot mixed paving mixtures and pavement samples for
specification acceptance, service, service evaluation, control and research.
Ans. extraction test
19. The bituminous Prime Coat materials should be applied by a pressure distributor at specified temperature and at an
application rate ranging from
Ans. 1 to 2 liters/m2
20. The rate of application for Bituminous Tack Coat materials (Item 302) ranging from
Ans. 0.2 to 0.7 liters/m2
21. The graduation requirement used for Hot Mix Bituminous Pavement
Ans. grading D
22. The placing temperature for Bituminous mixture measured in the truck prior to dumping
Ans. should not be less than 107 C
23. How many samples or core drilled samples be taken for each days full operation
Ans. at least one, but more than 3
24. The solvent used to test on residue from distillation at 288C of asphalt materials
Ans. trichloroethylene
25. At least three (3) weeks prior to production, the contractor shall submit in writing ________ for each mixture supported by
laboratory test data
Ans. job-mix formula
27. Sampling of PCCP/asphalt core specimens shall be taken form the pavement using
Ans. core drill
28. Size of asphalt core specimen for thickness and density determination
Ans. at least 150mm x 150mm (6 in. x 6 in.)
100mm diameter full depth
31. Obtaining asphalt core specimens for each full days operation shall be
Ans. at least one (1) but not more than three (3) core samples
34. The average of ________ measures are made on the asphalt core specimens in determining the thickness
Ans. four (4)
36. The average of four measurements on the asphalt core specimen is to determine the
Ans. thickness
37. The computation for the quantity of bituminous mixture, are the ff:
Given:
Paving length represented, m = 120.000
Thickness; cm = 5.000
Width, m = 3.050
Total length of pavement, m = 380.000
Density, gm/cm3 = 2.221
38. Main constituents of asphalt which is found in nature or as residue in petroleum refining
Ans. bitumen
43. Representative quantity of one (1) sample in sampling liquid asphalt is ________ sample for every
Ans. 1 quart to 1 gallon
46. A consistency test for solid asphalt that determines the hardness of asphalt
Ans. penetration
47. The properties of asphalt depends upon this _______ substance which is soluble in petroleum solvents as N-phases
Ans. petrolene
52. The objective is to determine as economical blend between graded aggregates and asphalt in order to produce a pavement
that would meet the required specification.
Ans. job-mix formula
53. Asphalt cement with water and a little amount of emulsifier, usually derivatives of salt
Ans. emulsified asphalt
54. Asphalt cement mixed with kerosene, block in color and liquid at room temperature
Ans. medium curing cutback asphalt
60. What physical test that determines if the asphalt is overheated during production?
Ans. spot test
61. What kind of asphalt cement that are commonly used in the Philippines?
Ans. 60 to 70 or 85 to 100
62. What test that will determine if the asphalt is a good binder?
Ans. ductility test
64. What property of mix that has the ability to resist deformation form an imposed load?
Ans. stability
65. What property of mix that has the ability to withstand repeated flexing caused by the passage of wheel load?
Ans. fatigue resistance
66. In Marshall Stability Test, which of the criteria not included in determining the average bitumen content?
Ans. flow
69. What property of mix that has the ability to offer resistance to slipping or skidding when mix?
Ans. skid resistance
72. What property of mix that has the ability to bend slightly without cracking and to conform to gradual settlement and
movements of the base and sub-grade?
Ans. flexibility
73. Mineral filler shall have a plasticity index of not greater than ________.
Ans. 4
74. The prime coat should not be disturbed for at least ________ hrs. and should not be ________ to traffic until it has
penetrated and cured efficiency.
Ans. 24 opened
75. Emulsified Asphalt is c colloidal dispersion of asphalt in water. It is ________ colored before use and turns ________ when
the emulsion is broken.
Ans. chocolate, black
80. What is a small air space that occurs between the coated aggregates particles in a compacted mix?
Ans. Air Voids
81. The compacted pavement shall have a density equal to, or greater than, ________ mass percent of the density of
laboratory specimen prepared in accordance with the ________.
Ans. 90- Marshall Stability Test
82. What is the measure of the resistance or measure of distortion of the specimen?
Ans. flow index
84. What do you call the wearing away of the pavement surface caused by the dislodging of aggregate particle?
Ans. raveling
85. The upward movement in an asphalt pavement resulting in the formation of a film of asphalt on the surface _______.
Ans. bleeding
88. For the same stretch of road, no core test was conducted at the end of each days operation. Thus, cores were taken for
every 100 linear meters of the completed pavement.
89. The specimen is tested for stability and flow at ________ C as specified in the standard procedure
Ans. 30 C
90. In the design of Air Voids, will draw down a line at ________.
Ans. 4.0
93. What is the apparatus used to check the temperature of asphalt mix/
Ans. Armored Thermometer
94. What do you call the localized upward displacement of a pavement due to swelling of the sub-grade or some portion of the
pavement structure?
Ans. upheaval
95. What do you call the slab movement under passing loads resulting in the ejection of mixtures of water, sand, clay or silt
along transverse or longitudinal joints?
Ans. pumping
96. What is the Item number of Bit Concrete Surface Course, 1 lot laid?
Ans. - 310
1. The standard penetration test (SPT) is an in-situ test that measures what?
Ans. depth of soil layer
2. Which of the ff. bituminous material is best recommended for sealing weakened plane joints?
Ans. joint filler asphalt (commonly called hard asphalt or blown asphalt)
3. The main problem associated with wrong practice of conveying concrete is called what?
Ans. segregation
4. The specification call for 1:2:4 concrete mix. In a one bagger mixer, which of the ff. amount of water is most likely required
for the mix?
Ans. 20 liters
5. A one lane road, with a pavement was designed to have subbase and base courses with a combined thickness of 300mm. If
the thickness of the subbase is a 125mm, the spreading and compaction of the subbase and base courses shabby be earned
out in:
Ans. 3 layers over the full width of 4.5 m.
6. As materials engineer, what is the area of the trial section that you would recommend to check the suitability of the
materials and efficiency of the equipment to be used for Item 310 Bituminous Concrete Surface Course?
Ans. about 500 sq.m.
7. Per program of work, the estimated volume of Item 201 materials is 7500 cu.m. How many grading and plasticity tests are
required based on the DPWH minimum testing requirements?
Ans. 25 grading and 25 plasticity
9. Quality of factory produced reinforced concrete pipes may be best established through what?
Ans. Test of concrete pipe samples
10. Where do we take additional cores when the measurement of any core taken from the pavement is deficient in thickness by
more than 25mm?
Ans. at no less than 5 meter intervals parallel to the centerline in each direction
from the affected location
11. The results of the Immersion-Compression test conducted on an asphalt mix sample are as follows:
Dry Stability = 2,000 Kpa
Wet Stability = 1,000 Kpa
What is the resulting Index of Retained strength? Does it meet the specification requirement of Item 310, Bituminous
Concrete Surface Course?
Ans.
Index Retained Strength or IRS = Wet stability x 100
Dry stability
= (1,000 Kpa/,000 Kpa) x 100
IRS = 50%
*No, it does not meet the specification of Item 310 since the specification of IRS is 70% minimum while the resulting IRS
here is only 50%.
12. Quality Control testing in a DPWH project is the responsibility of the ________?
Ans. Contractor Material Engineers
13. As materials engineers, when is the right time to start sampling and testing aggregate of the course materials?
Ans. before the course materials be incorporated in the project
15. Under what climatic conditions do we use the lower penetration grade or hard asphalt?
Ans. hot climate
16. Sampling of the freshly mixed concrete should be taken on the ________ batch discharge of the transit mixer?
Ans. middle
17. Soft and unstable soils were encountered during the course of sub-grade preparation. If you were the materials engineer
assigned to the project, what is the most effective and cheaper method that you would recommend to stabilize the soil prior
to the construction of the sub base course?
Ans. geotextiles
18. How many times per layer should a concrete specimen molded in a 6x6x12 beam mold be rodded?
Ans. 63 times
19. What is the basis for acceptance or rejection of any construction materials?
Ans. Materials Test Reports
20. In testing concrete cylinder sample the load applied should be continuous without shock at a constant rate within the range
of ________ per second.
Ans. 0.14 to 0.34 Mpa per second or 20 to 50 psi per second
21. During the application of the first half of the anticipated load a loading shall be permitted.
Ans. higher rate
22. Initial rolling in bituminous mixes shall be performed with a ________ roller.
Ans. Pneumatic Tire Roller
23. Final rolling in bituminous mixes shall be performed with a ________ roller.
Ans. 3 wheel or tandem type steel wheel roller
24. Rolling of Bituminous mix shall be discontinued whenever it begins to produce excessive ________ or ________.
Ans. pulverizing of the aggregate or displacement of the mixture
25. Final rolling shall be continued until roller marks are eliminated and a minimum ________ mass percent of the density of
the laboratory compacted a specimen prepared in accordance with AASHTO T160 has been obtained.
Ans. 95 mass percent
26. Sample from compacted bituminous mix shall be neatly cut by a saw or core drill. Each sample shall be at least ________.
Ans. 150mm x 150mm or 100mm diameter full depth
27. For surface tolerances the surface (bituminous mix) will be checked by the used of a ________ at sites selected by the
engineer.
Ans. 3 m straight edge
28. What is the sampling requirement for paving concrete for every 75 cu.m. or fraction thereof.
Ans. one (1) set (consisting of 3 pcs.) concrete beam sample
29. In testing bituminous beam sample for Immersion-Compression Stability is soaked in water bath for ________ days.
Ans. 4 days or 96 hrs.
30. Given:
Wt. of dry aggregate = 950g
Wt. of asphalt = 50g
31. Does the percent asphalt in problem #29 meet the required specification for percent asphalt in bituminous mixes? Why?
Ans. Yes, because standard specification for percent asphalt in bituminous mixes
is 5% to 8%
32. If the actual percent asphalt in problem #30 is 5% and the percent asphalt in a job-mix formula is 5.6% did it pass the
required tolerance? Why?
Ans. No, because the required tolerance for % asphalt in a job-mix formula is 1-0.4%.
35. Problems regarding quality of construction materials shall be reported directly by the contractors materials engineer to the
________.
Ans. DPWH Materials Engineer
36. How many concrete cylinder sample is required for a 300 pcs. Reinforced Concrete Culvert Pipes (RCCP)?
Ans. 12 sets (consisting of 3 pcs. cone, cylinder per set)
37. If concrete cylinder is not available for a 300 pcs. culvert pipes, how many pipes shall be subjected to test?
Ans. 6 pcs, culvert pipes
38. What kind of test that requires calibrated sand in filling the hole in order to determine the volume of hole?
Ans. Field Density Test (FDT)
1. What is the % weight of aggregates (coarse, fine and mineral filler) in the mixture of Bituminous Concrete Surface Course?
Ans. 92% to 95%
3. How can we establish the exact percentage to be used in the bituminous mixture?
Ans. job-mix formula
4. What are the two (2) types of bitumen that are commonly used in bituminous concrete surface course?
Ans. a.) Tar is a viscous liquid obtained from distillation of coal or wood
b.) Petroleum asphalt are the products of the distillation of crude oil.
13. How many weeks do a producer of asphalt mix or the contractors shall submit the job-mix formula?
Ans. three (3) weeks prior to production
16. What is the primary quality control mechanism for the production of asphalt mixture?
Ans. job-mix formula which shall conform to the ff. ranges of tolerance:
Passing No.4 and larger sieves 7%
Passing No.8 and No.100 sieves 4%
Passing No.200 sieves 2%
Bituminous materials 0.4%
Temperature of mixture 10 C
18. The mixture shall have a mass percent air voids with the range of ________?
Ans. 3.0%
20. What is the most commonly used method in the design and evaluation of bituminous concrete mixes?
Ans. Marshall Stability Method
21. The quality control tests for asphalt mix are the ff.:
Ans. a.) Immersion Compression Test determines the Index of Retained Strength of
the mix.
b.) Extraction and Grading Test determines the asphalt contains and particle
size distribution of coarse and fine aggregates
c.) Laboratory Density Test determines the degree and compaction
22. What is the correct temperature that the mixture shall be placed as measured in the truck just prior to dumping into the
spreader?
Ans. 107 C
23. When Tar is used, what is the temperature that the mixture shall be placed?
Ans. 66 C to 107 C
24. When the compaction is be done in order to attain the required density?
Ans. when the mixture is still hot and workable
25. What is to be done in order to determine the number of passes that would attain the required density?
Ans. trial section
26. What control during the mixing and compaction is of great significance in the strength of the resulting pavement?
Ans. temperature
27. What kind of roller should be used for the initial or breakdown compaction?
Ans. Pneumatic Tire Roller (not less than 10 tons)
28. For the final compaction and smoothing what kind of roller must be used?
Ans. Tandem smooth wheeled roller (not less than 10 tons)
32. The compacted pavement shall have a density equal to or greater than ________?
Ans. 95% of the laboratory compacted density
34. How many samples shall be taken for each full days operation?
Ans. at least one but not more than three (3) core samples
35. What is the dimension of the samples taken full depth from the finished pavement for thickness determination?
Ans. 150mm x 150mm or 100mm diameter
38. The variation of the surface from the testing edge of the straight-edge between contacts with the surface shall not exceed.
Ans. 6mm
39. What determines the thickness and density of compacted asphalt pavement?
Ans. core test
ITEM 311
40. What is the strength requirement (Flexural Strength) of a concrete when tested by third point loading method?
Ans. 3.8 Mpa (550 psi)
41. If No, 40 are tested by midpoint method what is the strength requirements?
Ans. 4.5 Mpa (650 psi)
42. What is the compressive strength of the PCCP (Portland Cement Concrete Pavement) when tested at 14 days?
Ans. 24.1 Mpa (3500 psi)
45. How long shall the forms remain undisturbed after concrete pouring?
Ans. 24 hrs.
46. When concrete is mixed in a central mixing plant how many seconds is the mixing time?
Ans. not less than 50 seconds or more than 90 seconds
47. In transporting concrete what is the time elapsed from the time water added to the mix until the concrete is deposited in
place at the site?
Ans. it shall not exceed 45 minutes if hauled in non agitating trucks and 90 minutes
when hauled in truck mixers or truck agitators.
49. How many seconds does the vibrator be operated in one location?
Ans. 15 seconds
51. How many sets of sample shall be taken from 330 sq.m. of pavement?
Ans. 1 set consisting of 3 concrete beam tests specimens or fraction thereof
52. If the lanes are concreted separately, what kind of joint in a form of key or keyway is used?
Ans. longitudinal construction joint
53. What kind of bars are placed perpendicular to the joint stated in no..52?
Ans. deformed steel tie bars
55. What is the depth of the weaken plane joint when sawed with a concrete saw?
Ans. not less than 50mm
57. When is the right time to saw the weaken plane joint?
Ans. within 24 hrs. as soon as concrete has hardened sufficiently
58. What shall be done if cracks appear at or near the joint prior to the time of sawing?
Ans. sawing shall be omitted
59. Tie bars shall not be coated or painted with ________?
Ans. asphalt or other materials
60. What is the metal device that is used as a load transfer device held in a position parallel to the surface and center line of the
slab of pavement?
Ans. dowels
61. To protect dowels from corrosion and to facilitate sliding in concrete, it shall be coated with _________?
Ans. thin film of bitumen
63. What is the depth of the corrugate produced by brooming in the surface of the pavement?
Ans. 1.5mm
64. The surface of the newly placed concrete when it is sufficiently set shall be cured for a period of ________?
Ans. 72 hrs.
70. What is the ration of fine aggregates to cement number of bags for grout in Item 505 & 505?
Ans. for Item 504, it is 1 part cement 3 parts fine sand (1:3)
- for Item 505, it is 1 part cement 2 parts fine sand (1:2)
1. What is the latest state of the art equipment containing a radioactive material which is commonly used in the
compaction control of earth and asphalt road construction and in the measurement of moisture content?
Ans. nuclear density gauge (NDG)
2. What is the instrument that is used for examining the quality of rigid materials such as rocks and concrete? (This
instrument or equipment is a non-destructive portable instrument with dimensions of 110 x 180 x 160mm and the
main uses include the determination of concrete strength (either in-situ or pre-cast0, also to determine the presence of
voids, cracks and other imperfections.)
Ans. pundit ultrasonic concrete tester
3. What is the instrument or equipment used for surface test of concrete and asphalt pavements as soon as the asphalt
mix has been initially compacted?
Ans. 3-meter straight-edge
4. ________ is an instrument used to measure pavement deflections resulting from vehicle wheel loadings. The results of
the elastic deformation tests are used to evaluate the structural conditions of roads, and to help in the design of road
strengthening measures and road capacity improvements.
Ans. Benkelman Beam and Deflection Logger
5. ________ is a manually-operated device for deriving a measurement of roughness from the surface profile, which may
be expressed in terms of International Roughness Index (IRI)
Ans. MERLIN Road Roughness Measuring Device
6. What is the instrument that is used to pinpoint rebars, conduits, pipes, nails and other metals embedded in concrete
before cutting or drilling?
Ans. rebar locator
7. ________ is equipment which is used to measure differential deflections between joints of a concrete pavement, to
determine the modulus of the existing slabs for use in the design of an overlay, and to estimate the remaining life of an
existing pavement.
Ans. falling weight deflectometer
8. ________ is used for the rapid in-situ measurement of the structural properties of existing with unbound granular
materials.
Ans. Dynamic Cone Penetration (DCP)
9. In the construction of bridge projects, what is the method used to determine the casting length of the regular piles?
Ans. test piling
1. The concrete pavement surface shows high spots of 15mm in a 3-meter straight edge. The concrete in the area represented
by these high spots.
Ans. - shall be removed and replaced
* but if high spots being noted exceeds 3mm, but not exceeding
12mm it shall be ground down only.
2. Steel bars placed along longitudinal joints to hold the adjoining slabs together are called:
Ans. tie bars
3. Which of the ff. is authorized to test materials for use in DPWH projects?
Ans. any DPWH accredited private testing laboratory
4. To check the gradation of aggregates and the asphalt content of laid bituminous concrete mixture, it shall be sampled and
tested for:
Ans. extraction test
5. For each full days operation, how many asphalt core samples must be taken for thickness determination?
Ans. at least one but not more than three core samples
10. Type of emulsified asphalt that works better with wet aggregates and cold weather:
Ans. cationic emulsion
2. Concrete area represented by the cores will be considered adequate if the average strength is equal to?
Ans. 85% of the required strength
5. Thickness determination for 1km concrete pavement. How many cores shall be taken?
Ans. 5/lane
7. The average compressive strength of a load bearing concrete hollow blocks is ________.
Ans. 1,000 psi
11. What are the other terms for particle size analysis?
Ans. sieve analysis
- mechanical analysis
- grading test/analysis
13. The liquid limit is expressed as the moisture content corresponding to what number of blows?
Ans. 25 blows
15. What kind of water shall be used in laboratory test especially if it deals with chemicals?
Ans. distilled water
16. Liquid limit brass cup with sample is raised and allowed to drop sharply on the base through a height of what?
Ans. 10mm
17. How many rotations per second will the crank of a liquid limit device are rotated?
Ans. 2 rotations per second
18. In doing plastic limit tests to what diameter will the soil thread will begin to break?
Ans. 3.2mm (1/8)
23. What is the maximum depth of roadway embankments per horizontal layer in loose measurement?
Ans. 200mm (8)
26. What is the required particle size for selected borrow for topping under Item 104 (embankment)?
Ans. all particle size will pass a sieve 75mm or 3 square openings and not more
than 15% mass will pass 0.075mm (No.200) AASHTO T-11
27. P.I. requirement for Item 104 (selected common borrow) is what?
Ans. 6 maximum
28. LL requirements for Item 104 (selected common borrow) are what?
Ans. 30 maximum
29. What is the LL requirement for Item 200 (aggregate sub-base course) passing sieve #40?
Ans. 35 maximum
30. P.I. requirement of materials passing sieve #40 for Item 200?
Ans. 12 maximum
31. Coarse portion retained on sieve #10 (2.00mm) for Item 200 shall have a mass percent of wear by Los Angeles abrasion
test of what?
Ans. 50% maximum
33. What is the minimum % field density or degree of compaction for Item 104 (embankment)?
Ans. 95% minimum
34. What is the minimum degree of compaction for Item 200 and 201?
Ans. 100% minimum
35. What is the highest point in moisture density curve of the moisture density relation test or compaction test of soil
represents?
Ans. MDD (Maximum Dry Density) and OMC (Optimum Moisture Content)
36. What is the required size of calibrated sand used for Field Density Test?
Ans. any clean, dry, free flowing, uncemented sand passing #10 and retained
#200 sieves
37. What is the degree of compaction of soil having a maximum dry density 2,250 kg./cu.m. and wet density of soil from hole
equivalent to 2,335 kg./cu.m. and an average moisture content of 8.85%?
% Degree of Compaction = (Dry Density) / Max Dry Density) x 100
Where:
Dry Density = Wet Density / (1+MC/100)
Wet Density = Wt. of soil filled in hole/volume of hole
39. What are the test and number of test needed for 1,800 cu.m. Item 104?
G or Grading = 2
P or Plasticity = 2
C or Compaction = 2
D or Density = three in-situ density tests/500 sq.m.
40. What are the test and number of test needed for 2,980 cu.m. Aggregates Base Course (Item 201)?
G = 10
P = 10
C=2
D = three in- situ density tests/500 sq.m.
CBR = 2 (1 test for every 2,500 cu.m. or fraction thereof)
Q=2
41. What are the apparatus/materials uses for Field Density Test?
Ans. sand cone, jug (at least 4 liters), guide plate, moisture cans, sand weighing
scale, oven with temperature control, chisel, or digging tools, plastic bags
and labeling materials (tag name)
45. A set of three beam samples is conducted representing ________ cu.m. of concrete.
Ans. 75
49. Determines the proportion of the ingredients that will produced concrete of proper workability when fresh and the________.
Ans. Design Mix
50. The maximum permissible water-cement ration for strength of 3,000 psi.
Ans. 0.58
52. For every 75 cu.m. of concrete poured, a minimum of ________ cylinder sample are taken in each day of pouring.
Ans. 3
54. Forms of concrete pavement shall not deviate from true line by more than ________ at any point.
Ans. 1 cm
55. When hauled in non-agitating trucks, the time elapsed from the water is added to the mix until concrete is deposited in
placed shall not exceed ________.
Ans. 45 minutes maximum
56. The depth of the weakened plane joint should at all times not less than
Ans. 50 mm
59. Vibrators shall not be operated longer than ________ in any one location.
Ans. 15 seconds
60. How many hours does a fine aggregates tested for specific gravity and absorption be soaked in water?
Ans. 15 to 19 hrs.
61. How to determine if the fine aggregates reaches the saturated surface dry condition?
Ans. it is determine by the use of cone test for surface moisture and if the molded
shape of fine aggregates slumps slightly, it indicates that it has reached a
surface dry condition.
63. What is the maximum mass % of wear by Los Angeles Abrasion Test?
Ans. 40% maximum
64. What is the required speed of Los Angeles Abrasion Machine per minute?
Ans. 30 to 33 mm
65. What is the size or diameter and weight of cast-iron spheres use in abrasion?
Ans. approximately 46.8 mm diameter and each weighing between
390-455 grams
66. What is the required total wt. of sample for abrasion test of coarse aggregate, grading A with 12 numbers of spheres?
Ans. 5,000 grams 25 grams
68. Quality test for cement is represented by how many bags of cement?
Ans. 2,000 bags or traction thereof
69. What is the sieve use in sieving materials form Abrasion Machine?
Ans. sieve # 12 (1.70mm)
70. Testing machines should be calibrated once every six (6) months if possible but if it is not possible what is the required time
should the machine be calibrated?
Ans. once a year
73. How many samples should be taken for every 75 cu.m. fresh concrete?
Ans. 3 pcs. sample or 1 set sample
77. How to compute for the compressive strength of concrete cylinder sample?
CS = P
A where : P = load, lbs
A = area, sq. in
A = D2 = 28.27 in sq
4
78. At what age should a concrete beam sample be tested for flexural test?
Ans. 14 days
79. How to compute the flexural strength of concrete beam sample tested at third Point Loading?
R = PL
A where: R = modulus of rapture
= P (16) P = load in lbs. of tons
6x6x6 L = span length in inches
=P B = base in inches
12 A = depth in inches
80. What is the minimum flexural strength for third point loading test?
Ans. 3.8 Mpa (550 psi)
81. What is the minimum flexural strength for center point loading test?
Ans. 4.5 Mpa (650 psi)
82. How to compute for flexural strength at center point loading test?
R = 3 PL
2 bd2
= 3 P (16)
2 (6) (6)
83. Which part of the batch for fresh concrete should the sample be taken from a stationary mixers, revolving drum truck
mixers or agitators?
Ans. two or more regular intervals during discharge of middle portion of the batch
84. What is the size of the tamping rod use in sampling concrete?
Ans. 16mm (5/8 inches) diameter and 610mm (24 inches) long with the tamping
end rounded to a hemispherical tip of the same diameter as the rod.
85. Concrete masonry (hollow blocks) if subjected to test how many sample is required?
Ans. 6 pcs. / 10,000 units * 12 pcs. if more than 10,000 units
86. What is the strength requirement for loading bearing concrete masonry units?
Ans. individual = 5.5 Mpa (300 psi) minimum
average (for 3 samples) = 6.9 Mpa (1,000 psi) minimum
87. How about for non-load bearing concrete masonry units what is the required strength?
Ans. individual = 3.45 Mpa (500 psi) minimum
average (for 3 samples) = 4.14 Mpa (600 psi) minimum
91. What is the required size of test specimen for G.I. Sheets?
Ans. 60mm x 60mm (3 pcs. from one (1) sheet / 1,000 sheets
93. What kind of paint that has a reflectance in the form of beads?
Ans. reflectorized traffic plant
95. What is this construction material that is dark brown to black cementations material in which the predominating constituents
are bitumen?
Ans. asphalt
103. What is the ideal penetration grade of asphalt use in tropical regions?
Ans. 85 to 100 (but some uses 60 to 70)
104. Tack coat is use in an existing bituminous of concrete pavement. True or false?
Ans. true
109. What is this construction material that is dark brown to black cementations
material in which the predominating constituents are bitumen?
Ans. asphalt
111. For how many hours or how long shall a bituminous prime coat left
undisturbed?
Ans. 24 hrs.
113. Bituminous prime coat is use to treat the surface of base course. True or false?
Ans. true
114. No tack coat or prime coat shall be applied when the weather is foggy or rainy.
True or false?
Ans. true
117. If concrete cylinder sample for RCCP is not available for compressive test, one
(1) whole piece RCCP for every 50 pieces RCCP will be submitted for quality
test. True or false?
Ans. true
118. One set (3 pcs.) concrete cylinder sample shall be taken for every how many
pieces of RCCP?
Ans. 25 pieces
2. As work progresses in a concrete pavement construction sampling of concrete for flexural strength test determination
should be taken using:
Ans. beam mold @ 63 strokes per layer
3. In order to determine the consistency of a concrete mixture, the most common method is:
Ans. slump test
4. The strength level of concrete for Item 3.11 will be considered satisfactory if:
Ans. the average of all sets of three (3) consecutive strength test results equals or
exceed the specified strength and no individual result is deficiency by 15% of
the specified strength.
6. When transporting concrete in a non-agitating truck, the time elapse from the time the water is added to the mix until the
concrete is deposited in place at site:
Ans. shall not be exceeding 45 minutes
7. In a concrete paving, 17,680 bags of cement shall be consumed up to its completion, compute for the number of quality
test required.
Ans. 9
9. One of the most important characteristics of concrete is workability, which generally mean:
Ans. the concrete mix could be easily placed without segregation
10. Sawing of construction joint shall be done when the concrete is sufficiently hardened usually at:
Ans. 24 hrs.
11. A non-load bearing hollow blocks should have an individual strength requirement average of:
Ans. at least 3.45 Mpa (500 psi), 4.14 Mpa (600 psi) minimum