Professional Documents
Culture Documents
Samsung GT-i9000 Service Manual
Samsung GT-i9000 Service Manual
Samsung GT-i9000 Service Manual
GT-i9000B
1. Safety Precautions
2. Specification
3. Product Function
4. Exploded View and Parts list
5. MAIN Electrical Parts List
6. Level 1 Repair
7. Level 2 Repair
8. Level 3 Repair
9. Reference data
Notice
All functionality, features, specifications and o
ther product information provided in this docu
ment including, but not limited to, the benefit
s, design, pricing, components, performance,
availability, and capabiliti-es of the product
are subject to change without notice or oblig
ation. Samsung reserves the right to make
changes to this document and the product
described herein, at anytime, without
obligation on Samsung to provide notification
of such change.
GSPN (Global Service Partner Network)
Country Web Site
North America service.samsungportal.com
Latin America latin.samsungportal.com
CIS cis.samsungportal.com
Europe europe.samsungportal.com
China china.samsungportal.com
Asia asia.samsungportal.com
Mideast & Africa mea.samsungportal.com
This Service Manual is a property of Samsung Electronics Co.,Ltd. Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law. 2010. 07. Rev.1.0
1. Safety Precautions
Be careful to use a kind of magnetic object or tool, because performance of parts is damaged by
the influence of magnetic force.
Surely use a standard screwdriver when you disassemble this product, otherwise screw will be
worn away.
Repair after separate Test Pack and Set because for short danger (for example an overcurrent
and furious flames of parts etc) when you repair board in condition of connecting Test Pack and
tuning on.
Take specially care of soldering, because Land of PCB is small and weak in heat.
Surely tune on/off while using AC power plug, because a repair of battery charger is dangerous
when tuning ON/OFF PBA and Connector after disassembling charger.
Don't use as you pleases after change other material than replacement registered on SEC System.
Otherwise engineer in charge isn't charged with problem that you don't keep this rules.
1-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Safety Precautions
Several semiconductor may be damaged easily by static electricity. Such parts are called by ESD
(Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below.
You can prevent from ESD damage by static electricity.
Remove static electricity remained your body before you touch semiconductor or parts with
semiconductor. There are ways that you touch an earthed place or wear static electricity prevention
string on wrist.
Use soldering removing tool to break static electricity. Otherwise ESD will be damaged by static
electricity.
Don't unpack until you set up ESD on product. Because most of ESD are packed by box and
aluminum plate to have conductive power,they are prevented from static electricity.
You must maintain electric contact between ESD and place due to be set up until ESD is
connected completely to the proper place or a circuit board.
1-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
2. Specification
WCDMA210
GSM850 EG SM 900 DCS1800 PCS1 900 WCDMA850
0
Fr eq.
Band[MHz] 824~ 849 880~ 915 1710~ 1785 1850~ 1910 1922~ 1977 824~ 849
Uplink/Downlin 869~ 894 925~ 960 1805~ 1880 1930~ 1990 2112~ 2167 869~ 894
k
U L : 41 3 2~ 4 2 33
, 7 8 2, 78 7 , 80 7
0~1 24 & U L : 96 1 2~ 9 8 88 , 8 1 2, 83 7 , 86 2
ARF CN r ange 128~ 251 512~ 885 512~ 810 D L : 1 05 6 2~ 1 0 83 8 D L : 43 5 7~ 4 4 58
975~1 023 , 1 0 07 , 1 0 12 , 1 03 2
, 1 0 37 , 1 0 62 , 1 08 7
Fr ameLeng t Fr ameLeng t
Ti m e Sl ot h: h:
576. 9us 576. 9us 576. 9us 576. 9us
Pe rio d/Fr am e 1 0m s 1 0m s
4.615 ms 4.615 ms 4.615 ms 4.615 ms
Per iod Slotlengt h: Slotlengt h:
0.667 ms 0.667 ms
Modula tion 0.3 GMSK 0.3 GMSK 0.3 GMSK 0.3 GMSK Q PS KH Q PS Q PS KH Q PS
K K
Powe r Class 5pcl ~ 5pcl ~ 19pcl 0pcl ~ 15pcl 0pcl ~ 15pcl 3(max+24dB 3(max+24dB
19p cl m) m)
TDMA Mux 8 8 8 8 8 8
2-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Specification
15 05 dBm 15 05 dBm
2-2
Main Function
TouchWiz 3.0 for Android, Multistage, Augmented Reality, Integrated phonebook with
3-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
4. Exploded View and Parts List
4-1
4-2
5-1
5-2
5-3
5-4
5-5
5-6
Please consult the GSPN website (Samsung Portal) for the most recent version of the product's part list.
5-7
Settings
Data Cable
6-1
SAMSUNG Proprietary-Contents may change without notice
6-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Level 1 Repair
1. Option Selection
- Check Auto Reboot and F. Reset Time
6-3
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Level 1 Repair
OK Button
4. Connect the Handset to PC via a Data Cable. Make sure ID:COM box
highlighted yellow to know that the handset is connected to the PC.
6-4
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Level 1 Repair
6-5
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
7. Level 2 Repair
1 Unscrew screws on the rear 2 Unhook the rear using a disassembly knife
to remove the rear cover
Unscrew 7 screws on the rear using a screw driver. Be careful not to damage the rear cover when
screw torque : 1.2 ~ 1.4 kgf.cm unhooking it.
3 Detach the Power Key FPCB 4 Disconnect connectors from the Main PBA
Detach the power key FPCB, that is stick to the bracket Disconnect LCD Connector,Receiver Connector, Sub-
by a double-sided tape, using tweezers. Make sure to touch Key Connector and Antenna cable from the Main
remove all remaining tape on the bracket. PBA
7-1
After disconnecting the connectors carefully pull the Main Remove the antenna cable from the main Antenna PCB
PBA out of the bracket. on the sub-touch key module.
Pull out the Receiver module from the bracket. Be Remove the camera module from the Main PBA by
careful not to damage the FPC. pulling it out.
7-2
9 Pull out the Main PBA 10 Remove the top shield can
After disconnecting the connectors carefully pull the Main Be careful not to damage the shield can and the
PBA out of the bracket. components when removing it.
11 Remove the rear shield can + Sim Card PBA 12 Remove the speaker
7-3
7-1-2. Assembly
1 Place the top shield can. 2 Connect the speaker to the Sim Card PBA
3 Place the Sim Card PBA + shield can 4 Connect the Sim Card PBA Connector
7-4
Place the top shield can on the top of the main PBA Connect the camera module to the Main PBA
Place the receiver module onto the bracket. Connect the antenna cable to the Main Antenna PCB
7-5
9 Place the Main PBA 10 Connect LCD, Sub-touch key, Antenna and
Receiver connectors and place the Power
key
Make sure all the hooks are placed correctly, and Screw 7 points on the rear cover
press the volume keys and the power key for tensions. screw torque : 1.2 ~ 1.4 kgf.cm
7-6
8-1
8-2
8-2-1. Bottom
8-3
Equipments
8-4
8-3-1. Power On
Yes
Yes
Yes
No
Check the Battery Voltage Change the Battery
is more than 3.3V (Because of batt. power low)
Yes
Check U503 (PMIC) and Check the problem point (short, open, crack
Power on voltage No
(C518 >1.2V, C519 >1.1V, etc)
C520>1.8V, C522,> 1.2V C529
> 1.8V) and If PMIC has problem, change U503
Yes
Yes
check the initial operation
Yes
END
8-5
8-6
8-3-2. Initial
Initial Failure
Yes
Yes
AP_PS_HOLD(TP501) and No
AP_N_RST_IN (R507) = Check U503 (crack, open, etc)
"low High"? (if U503 has some problem, it is to be replaced)
Yes
No
There is 32.768KHz wave forms Replace OSC 200 and OSC501
at OSC200 and OSC501
Yes
No
Check UCP200 and related parts (short, crack,
R233 >= 1.8V? etc)
Yes
Yes
No
LCD display OK? Check the LCD part (short, crack, etc)
Yes
No
Sound is OK? Check the Audio Part (short, crack, etc)
Yes
END
8-7
8-8
Yes
Yes
Yes
Yes
END
8-9
8-10
NO SIM
Yes
Yes
Yes
END
8-11
Yes
Yes
Yes
Yes
END
8-12
8-13
No
Check signals on L209,
L210 Resolder or replace U207
Yes
No
Yes
Yes
END
8-14
8-15
Yes
Yes
Yes
Yes
Yes
END
8-16
8-17
8-3-8. BT/WIFI
Yes
Yes
Yes
Yes
Yes
Yes
END
8-18
8-19
8-3-9. FM RADIO
Yes
Yes
Yes
Yes
CChange U104
Yes
END
8-20
8-21
8-3-10. LCD
Yes
No
Check the connection of Reconnect the HDC300
HDC300
Yes
Yes
Check VCC_3.0V_LCD =
3.0V (C537), VLCD_1.8V = No
Check PMIC(U503)
1.8V (C307), V_BAT > 3.4V
(C308)
Yes
Yes
END
8-22
8-23
8-3-11. TSP
Yes
No
Check LCD Connector on Reconnect the HDC300
Main PBA
Yes
No
Check the TSP Connector on Reconnect TSP Connector
LCD Module
Yes
Yes
Yes
END
8-24
8-25
8-3-12. 5M CAM
Yes
No
Check the Camera Reconnect the HDC301
connector on Main PBA
Yes
Yes
No
Check F308 Pin 1 is 24MHz Check UCP400 related to 24MHz
Yes
END
8-26
D E TB A T
B A TT
B A TT
VIC H G
V C O IN
D C IN
D C IN
B A T TMON
VL
A1
BUCK1 IN1
A2
IN1
E1
BUCK2 IN2
E2
IN2
H1
BUCK3 IN3
H2
IN3
K2
BUCK4 IN4
K8
LDO4,5,7 IN5
K9
VALIVE_1.2V_C110
IN5
C9
LDO11,12,13 IN6
D9 VUSB_1.1V_C110
IN6
A7
LDO14,15,16 IN7
B7
VADC_3.3V_C110 VCC_2.8V_PDA
IN7
G9
LDO6,8,9 IN8
H9 VTF_2.8V VUSB_3.3V_C110
IN8
B9
LDO2,3,10,17 IN9
CAM_SENSOR_CORE_1.2V
B8 0.8V~1.3V UP TO 10mA CAM_ISP_HOST_2.8V
LDO2
C8 0.8V~1.3V UP TO 50mA
VLCD_1.8V VDAC_3.3V_C110
LDO3
K10 1.6V~3.6V UP TO 300mA
CAM_ISP_SYS_2.8V
U503 LDO4
LDO5
J10 1.6V~3.6V UP TO 300mA VPLL_1.2V_C110
H10 1.6V~3.6V UP TO 150mA
LDO6
K7 1.6V~3.6V UP TO 150mA CAM_ISP_RAM_1.8V
LDO7
G10 3.0V~3.6V UP TO 150mA
CAM_AF_2.8V VCC_3.0V_LCD VCC_1.8V_PDA
LDO8
F10
LDO9
C7
LDO10
E10 CAM_SENSOR_IO_1.8V VARM_1.2V_C110
LDO11
D10
LDO12
C10
LDO13
A6
VINT_1.1V_C110
LDO14
A8
LDO15
A10
LDO16
B10
LDO17
B1
LX1
B2
LX1
C1
CAM_ISP_CORE_1.2V
LX1
F1 L502
LX2
F2
LX2
F3
LX2
J1 L503
LX3
J2
LX3
J3 L504
LX4
K3
LX4
A4
XIN
A3
XOUT
PG N D 4
PG N D 4
PG N D 3
PG N D 2
PG N D 2
P GND1
PG N D 1
A G N D2
A G N D1
NC
NC
C522 C524 C525 C526 C527 C528 C529 C532 C533 C534 C535 C536 C537 C518 C519 C520 C521
K4
K1
G2
G1
D2
D1
B5
A5
J4
2
1
V_BAT CAM_SENSOR_A2.8V
F308
L309
U303 1 IN1 5
CAM_MCLK_F OUT1 CAM_MCLK
2 IN2 6
CAM_HSYNC_F OUT2 CAM_HSYNC
4 VDD VOUT 1
3 IN3 7
CAM_VSYNC_F OUT3 CAM_VSYNC
4 IN4 8
2 CAM_PCLK OUT4 CAM_PCLK_F
3 CE C315
CAM_IO_EN GND GND GND
GND
10 9
5
C351 C352
8-27
8-3-13. GSM900 RX
NORMAL CONDITION
catch the channel?
NO
NO
NO resolder or change
Check the Voltage at
PAM101, C186
C186 =V_BAT
YES
YES
YES
YES
YES
YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100
YES NO
GSM850 Receiver is O.K? resolder or change
UCP200
END
8-28
8-29
8-3-14. GSM1800 RX
NORMAL CONDITION
catch the channel?
NO
NO
YES
YES
YES
YES
YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100
YES NO
GSM850 Receiver is O.K? resolder or change
UCP200
END
8-30
8-31
CONTINUOUS RX ON
NORMAL CONDITION RF INPUT : 10700CH
catch the channel?
AMP : -50dBm
NO
NO
YES
YES
YES
YES
YES
NO change or resolder
Check the freq. at OSC100
:26MHz ? OSC100
YES
NO resolder or change
WCDMA BAND1 Receiver is O.K? UCSP200
YES
END
8-32
8-33
CONTINUOUS RX ON
RF INPUT : 9800CH
NORMAL CONDITION AMP : -50dBm
catch the channel?
NO
NO
YES
YES
YES
YES
YES
NO change or resolder
Check the freq. at OSC100
:26MHz ? OSC100
YES
NO resolder or change
WCDMA BAND2, PCS1900 Receiver is O.K? UCSP200
YES
END
8-34
8-35
CONTINUOUS RX ON
RF INPUT : 4407CH
NORMAL CONDITION
catch the channel? AMP : -50dBm
NO
NO
YES
YES
YES
YES
YES
NO change or resolder
Check the freq. at OSC100
:26MHz ? OSC100
YES
NO resolder or change
WCDMA BAND8, GSM900 Receiver is O.K? UCSP200
YES
END
8-36
8-37
NO CHECK soldered
PAM101 PIN1 : About RFS100, L103,C115,L118,
30dBm ? C183, ANT102
YES
YES
YES
YES
YES
YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100
YES NO
GSM850/900 Transmitter is O.K? resolder or change
UCP200
END
8-38
NO CHECK soldered
PAM101 PIN1 : About RFS100, L103,C115,L118,
27dBm ? C183, ANT102
YES
YES
YES
YES
YES
YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100
YES NO
DCS/PCS Transmitter is O.K? resolder or change
UCP200
END
8-39
8-40
YES
YES
NO
Check C135 resolder or change
about 3.4 V ? U102
YES
YES
NO resolder or change
Check C147
about 8dBm ? U101
YES
YES
YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100
YES NO
WCDMA 2100 Transmitter is O.K? resolder or change
UCP200
END
8-41
8-42
YES
YES
NO
Check C135 resolder or change
about 3.4 V ? U102
YES
YES
NO resolder or change
Check C146
about 8dBm ? U101
YES
YES
YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100
YES NO
WCDMA 1900 Transmitter is O.K? resolder or change
UCP200
END
8-43
8-44
YES
YES
NO
Check C135 resolder or change
about 3.4 V ? U102
YES
YES
NO resolder or change
Check C145
about 8dBm ? U101
YES
YES
YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100
YES NO
DCS/PCS Transmitter is O.K? resolder or change
UCP200
END
8-45
8-46
8-3-23. ISDB-T
Continous ISDB-T
PLAY
Yes
YES
YES
NO
Check 26Mhz Clock on Check & Replace
OSC701 OSC701
YES
YES
END
8-47
8-48
- NC Point(Top View)
: NC
UCP400
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L
M M
N N
P P
R R
T T
U U
V V
W W
Y Y
AA AA
AB AB
AC AC
AD AD
AE AE
AF AF
AG AG
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
8-49
: NC
UCP200
8-50
: NC
UME301
8-51
Reference Abbreviate
9-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Notice
Product GSM Notice No. 10-67
Model GT-I9000 Notice Date 5th Oct 10
Subject How to enter download mode
1. Purpose
- To inform All Authorized Service Center of information about technical TIP
2. Instruction
- There is two ways to enter Download mode in GT-I9000 model.
- If phone cannot enter to Download mode with H/W key combination, you can
do it with Anyway JIG too.
Volume
down Power
1) Key Combination. key
Turn off phone Press and hold Volume down +
Home Key + Power Key Home
Key
2) Anyway JIG connection
If phone cannot enter to download mode with H/W Key combination,
you can use the Anyway JIG (S100 or S101)
Turn off phone Change Anyway JIG option refer to below
- Solution Setting : 2 Infineon
- Function Setting : 2 and 6
- VBATT : ON
If you dont have USB cable connecting PC with Anyway JIG, you have to use data
cable connecting PC with phone, and must have battery to download S/W.
H/ W Pl at f or m 2 Gr oup
CP
RESET I C AP
Movi NAND
GPS
Accel er omet o
r
Vol ume Keys
RF I C
Power
Key Mai n ANT Conn.
RF s wi t chi ng
Magnet i c IC
Sens or
Mot or LNA
Audi o Codec Dr i ver
2. 5G PAM
Sub- Touch Key Connect or SAMSUNG Electronics Co., Ltd.
A ssy
5M Camer a VGA Camer a Speaker Recei ver BT/ Wi Fi ANT
3. 5pi Li ght / Pr oxi mi t y
Ear j ack Sens or s
LCD Con
Mi cr o SD
TSP
Cont r ol l er
start
Execute
Infineon_RFCAL_V11_3G.exe
1. Pre-Process : un-check
2. DGS Read : un-check
3. FDT Option : if you have
License : check ,
no-License : un-check
1. Message Wating. ST
Signal
2. Click the M/A button
3. Change Automatic mode
to Manual mode