Professional Documents
Culture Documents
Uputstvo Za Instalaciju: Jetspeed Iad-Wp2
Uputstvo Za Instalaciju: Jetspeed Iad-Wp2
ZA INSTALACIJU
JetSpeed IAD-Wp2
INTRACOM -TELECOM - Documentation Section
All copyright, intellectual and industrial rights in this document and in the technical knowledge it contains
are owned by INTRACOM S.A. TELECOM SOLUTIONS and/or their respective owners.
This document is made available to the end users only for their internal use.
No part of this document nor any data herein may be published, disclosed, copied, reproduced,
redistributed by any form or means, electronically or mechanically, or used for any other purpose
whatsoever without the prior written approval of INTRACOM S.A. TELECOM SOLUTIONS.
Information as well as drawings and specifications contained in this document are subject to change
without prior notice.
All trademarks and copyrights mentioned herein are the property of INTRACOM S.A. TELECOM
SOLUTIONS and/or their respective owners.
Any rights not expressly granted herein are reserved.
Printed in Greece.
JetSpeed IAD-Wp2
User Manual Edition 1.0
Table of Contents
Introduction........................................................................................................................... 5
Networking Capabilities .................................................................................................. 7
Applications .................................................................................................................... 8
Hardware Description & Requirements ........................................................................... 9
Package Contents ........................................................................................................ 10
Front Panel ................................................................................................................... 11
Rear Panel.................................................................................................................... 13
Appendix C: Troubleshooting............................................................................................ 51
1
JetSpeed IAD-Wp2
User Manual Edition 1.0
2
JetSpeed IAD-Wp2
User Manual Edition 1.0
Declaration of Conformity
Equipment Disposal
This symbol, found on this product and any of its parts or on its operating
instructions or on its packaging, indicates that electrical and electronic
equipment may not be disposed of as unsorted municipal waste. Instead,
this product should be handed over to applicable collection points for the
recycling of electrical and electronic equipment.
By ensuring the correct disposal of this product, you will help prevent
potential negative consequences to the environment and human health,
which could otherwise be caused by inappropriate disposal of this product.
By recycling, reusing and other forms of recovery of old electrical and
electronic equipment you are making an important contribution to the
conservation of natural resources and to the protection of the environment.
For more information about the recycling of this product, please contact your
local municipal authorities, municipal waste disposal service or the store
where you purchased this product.
3
JetSpeed IAD-Wp2
User Manual Edition 1.0
Follow all the instructions with care. You must read the following
safety information carefully before you install or remove the
device.
Use only the power adapter that is supplied with the unit. The use of
an alternative adapter can damage the device and invalidate the
warranty
Use an electrical outlet within easy distance. Take care not to
damage the power cable
To avoid electrical shock, do not open the device
To prevent fire or shock hazard, do not expose your device to rain or
moisture, liquid and toxic substances
Particular care must be taken during installation and removal of
cables and telephone line
Never touch the non-insulated telephone wires or terminals unless
the telephone line has been disconnected from the network interface
Ensure the correct ventilation of the device. Do not obstruct the air
exhaust outlets and do not lean anything over the device
Place the device out of direct sunlight and away from sources of heat
Avoid using your device during an electrical storm as it may cause an
electrical shock
The device generates and uses Radio Frequency (RF) energy. In
some environments, the use of RF energy is not permitted. The user
should seek local advice on whether or not RF energy is permitted
within the area of intended use
4
JetSpeed IAD-Wp2
User Manual Edition 1.0
Introduction
Overview The JetSpeed IAD-Wp2 device (see photo below) is a Router that
employs ADSL2+ technology, having the capability to provide a cost-effective
means of sharing a single broadband Internet connection, between several
wired and wireless computers.
JetSpeed IAD-Wp2 is also applicable to SOHO customers for the
provisioning of broadband services from a single access point.
5
JetSpeed IAD-Wp2
User Manual Edition 1.0
Introduction, Continued
VoIP Services Using VoIP, instead of making calls over the regular telephone network, calls
are made over internet (IP), either through your Internet Service Providers
(ISP) connection or through your local network (LAN). Calls made to other
VoIP devices, anywhere in the world, are generally free, while long distance
calls are much cheaper to regular telephone calls made through the public
telephone network.
The basic functionalities of the device include the conversion of an analogue
voice signal to digital, the encoding and then compression of the signal into
Internet protocol (IP) packets. The device is equipped with a digital signal
processor (DSP), which segments the voice signal into frames and stores
them in voice packets. These voice packets are encoded using the G.711,
G.723.3 and G.729 standards used by encoders - decoders (Codec) of the
market.
1
More USB devices like WEB cameras will be supported in the future with firmware upgrades
6
JetSpeed IAD-Wp2
User Manual Edition 1.0
Networking Capabilities
POTS
Line
POTS
POTS
Voice
Splitter
Wi-Fi
Residential
Connection Data
Point (NID)
JetSpeed IAD-Wp2 Clients
LAN
USB
Clients
VoIP
Ethernet Hub
or Switch
LAN
VoIP (extension)
7
JetSpeed IAD-Wp2
User Manual Edition 1.0
Applications
USB Printer Using the implemented USB Host the JetSpeed IAD-Wp2 can be used for
Sharing (LAN & Printer sharing in a LAN or WAN configuration thus the printer can be
WAN) accessed remotely from a different location.
File Sharing Using the implemented USB Host the JetSpeed IAD-Wp2 can be used for
(LAN & WAN)
File Sharing by connecting your USB Flash memory stick. Your files could be
accessed either from LAN or WAN (Internet).
8
JetSpeed IAD-Wp2
User Manual Edition 1.0
System Your device requires that the computer(s) and components in your network
Requirements be configured with at least the following:
An Operating System (could be Windows, OSX, Linux or other Unix
variations)
Each computer to be connected to the available LAN ports of the
device should be equipped with a 10Mbit/s or 10 / 100 Mbit/s Ethernet
card
Optionally, an 802.11b/g wireless adapter
At least 60 MB of free hard disk space
At least 256 MB of RAM
Suitable web browser. Supported are the following: Internet Explorer
5.5 or later, Netscape 4.7 or later, Firefox Mozilla 1.5 or later
9
JetSpeed IAD-Wp2
User Manual Edition 1.0
Package Contents
# Depiction Description
1 JetSpeed IAD-Wp2 unit (ISDN or POTS,
depending on your telephone line type).
3 Ethernet cable.
4 2 x Phone cables.
5 Resources CD ROM.
6 ADSL splitter.
10
JetSpeed IAD-Wp2
User Manual Edition 1.0
Front Panel
LEDs
11
JetSpeed IAD-Wp2
User Manual Edition 1.0
continued
WLAN To enable/disable Wi-Fi in JetSpeed IAD-Wp2 press the WLAN button for
approximately 2 seconds.
To auto-configure the Wi-Fi connection (WPS) between your computer and
the JetSpeed IAD-Wp2 press the WLAN button for approximately 6
seconds and then release. The WPS LED will start blinking in Amber color. .
Note that your Wireless Client Card must support WPS.
12
JetSpeed IAD-Wp2
User Manual Edition 1.0
Rear Panel
Description
# Designation Description
1 ADSL Connection port of ADSL line.
2 LAN1 LAN2 Fast Ethernet (RJ-45) ports for connecting LAN
LAN LAN4 devices, such as computer, Hub or Switch, etc.
3 USB USB Host to connect a printer or a USB Stick.
4 Power Power adapter receptacle.
5 On/Off Switch to turn the device ON / OFF.
6 Reset Reset button to reset the device and restore default
factory settings.
7 Line Telephone line receptacle (FXO lifeline backup,
(optional) optional).
8 Phone 1 Analogue Telephone device (FXS) receptacles.
Phone 2
13
JetSpeed IAD-Wp2
User Manual Edition 1.0
This chapter will guide you through the installation of JetSpeed IAD-Wp2,
including:
1. Positioning the device
2. Installing the ADSL splitter or Micro filters
3. Connecting the device to the network
4. Setting up your computer for networking communication with the
device
Please read carefully the Safety Information in the beginning of this manual.
Do not force the antenna beyond its mechanical stops. Rotating the antenna
further may cause damage.
14
JetSpeed IAD-Wp2
User Manual Edition 1.0
Introduction A splitter separates the frequencies of telephone service from the ADSL
(Data) service and outputs each to a different splitter port. The Line port of
the splitter is connected to a telephone wall socket. If you have an ISDN
telephone line then, the Phone port must be connected to the NT1 unit (i.e.
Intracom netMod). If you have a POTS line then, the Phone port shall be
used to connect telephone sets. The ADSL port shall be connected to
JetSpeed IAD-Wp2, no matter if POTS or ISDN line is used.
Step Action
1 Connect the Line port of the splitter to the wall
socket.
2 Use an RJ11 cable to connect the JetSpeed IAD-
Wp2 ADSL port to the ADSL port of the splitter.
3 Connect a telephone set in the Phone port of the
splitter.
15
JetSpeed IAD-Wp2
User Manual Edition 1.0
Introduction You may want to reset the JetSpeed IAD-Wp2 in case you are
experiencing problems or if you want to restore the factory default settings.
Procedure To Reset the JetSpeed IAD-Wp2 press the Reset button located in the
rear panel of the device, next to the ON/OFF button, for approximately 2
seconds.
To Restore the JetSpeed IAD-Wp2 to factory default settings press the
Reset button for approximately 5 seconds.
Description Make sure that TCP/IP is installed and supported by your operating system.
This connection will require you to enable your computer to receive from the
device its own IP Address automatically: in such a case, the device acts like
the DHCP server in your local network.
16
JetSpeed IAD-Wp2
User Manual Edition 1.0
Wi-Fi Connection
Step Action
1 Install your wireless adapter according to the manufacturers
instructions and verify that your computer is set to obtain an IP
address automatically (DHCP Client mode).
Note: You will need to properly configure your adapter to
communicate with JetSpeed IAD-Wp2 according to the
configuration rules. This requires a computer with 802.11b/g wireless
adapter installed.
2 In the configuration window of your wireless adapter scan the
wireless network (indicated with the relevant SSID name) present in
your physical environment
3 Select the SSID of JetSpeed IAD-Wp2.
4 Complete the configuration of the wireless adapter with the same
parameters of JetSpeed IAD-Wp2 which are:
RF channel; automatically detect
Encryption Enable or Disable (default = Enable). Choose
between WEP, WPA/WPA2 and WP2 only.
Set WEP/WPA/WP2 key size/type
Set WEP/WPA/WPA2 key used
5 To check the connection, connect to the JetSpeed IAD-Wp2
Home Page, entering http://192.168.1.1/ in the address bar of your
browser.
Important Note: Your ADSL router has been set by default to use
WPA/WPA2 security. The pre-shared key that is intended to be used by the
clients is typed on the bottom side of each device.
17
JetSpeed IAD-Wp2
User Manual Edition 1.0
Connecting This section describes how to connect to the JetSpeed IAD-Wp2 Wi-Fi
using WPS- Access Point using Wireless Protected Setup Push Button Configuration
PBC (Push (WPS-PBC).
Button
Configuration)
NOTE Use the following procedure only for WPS enabled Wireless clients
and operating with Windows Vista or newer operating systems
with embedded WPS support. If you are using an older or different
than Windows Vista OS, then please consult the user manual
of your Wi-Fi client adapter to use WPS.
Step Action
1 Navigate to the WIRELESS > WPS menu and select Enable.
2 Press the Save button to confirm your selection.
3 Use your computers wireless utility to locate the available
wireless networks and select the SSID of the JetSpeed IAD-
Wp2. Press the Connect button as indicated in the following
screen:
18
JetSpeed IAD-Wp2
User Manual Edition 1.0
Connecting
using WPS-
Step Action
PBC (Push
Button 4 The message inside the red frame indicates that an Access Point
Configuration) with WPS-PBC capabilities has been detected. Press the WLAN
(continued) button in JetSpeed IAD-Wp2 for at least 6 seconds and then
release it. The WPS LED is now blinking in amber colour.
19
JetSpeed IAD-Wp2
User Manual Edition 1.0
20
JetSpeed IAD-Wp2
User Manual Edition 1.0
Introduction This chapter provides a description of all menu items accessible from the
Home Page of JetSpeed IAD-Wp2 on user authentication to the Router.
HOME PAGE
Introduction The devices setup program is web-based, which means that it is accessed
through your web browser.
Step Action
1 Launch your web browser on your computer.
2 Enter the following URL in the address field of your browser:
http://192.168.1.1/ or alternatively use the easy URL address
Access Access to the device configuration pages is controlled through user account:
telekom
User telekom has restricted access to change and view configuration of
the device.
You will be requested to insert an ID and a Password: insert them to access
the devices configuration panels.
The username (ID) and password are set to telekom for the user account.
It is recommended to change the default password. Make sure you
remember the new password, since this is the only way you will be able to
manage your device.
21
JetSpeed IAD-Wp2
User Manual Edition 1.0
22
JetSpeed IAD-Wp2
User Manual Edition 1.0
Home Page The main configuration page opens as shown in the following figure. This
Description page contains a menu on the left which is always available in all pages and
which is the starting point for any configuration that concerns JetSpeed IAD-
Wp2.
Menu Description The following table provides a description of the menus which are
located on the left side of the main configuration page (Home Page):
Menu Description
WIRELESS To set up the wireless access point configuration.
NAT Port Forwarding configuration (to allow external connections to your
private network)
ROUTE A Status view of IADs routing table records
FIREWALL To set up the firewall protection parameters.
ADSL The status of your ADSL connection
VoIP A status view of VoIP calls and events
QoS A brief status of packets traffic per QoS priority queue
USB To setup the connected USB devices and the related services
TOOLS A set of tools to perform backup / restore, reset or Firmware upgrade
tasks.
STATUS A status summary of IAD running configuration and system messages.
Home Logout In the top right part of the screen click Home to go to the Home Page or click
Logout to Logout.
23
JetSpeed IAD-Wp2
User Manual Edition 1.0
WIRELESS Menu
To enable the Wireless transmitter click the Enable option button and click
the SAVE SETTINGS button.
Channel & SSID You must specify a common radio channel and SSID (Service Set ID) to be
used by JetSpeed IAD-Wp2 and all of its wireless clients. Be sure you
configure all of its clients with the same values.
Parameter Description
SSID Service Set ID. The SSID must be the same for JetSpeed
IAD-Wp2 and all of its wireless clients.
Wireless This device supports both 11g and 11b wireless networks.
Mode Select according to the type of your wireless network. You may
use Mixed (11b+11g) to provide compatibility with both 11b
and 11g wireless clients.
Channel The radio channel used by the wireless device and its clients
to communicate with each other. This channel must be the
same for JetSpeed IAD-Wp2 and all of its wireless clients.
JetSpeed IAD-Wp2 will automatically assign itself a radio
channel, or you may select one manually.
24
JetSpeed IAD-Wp2
User Manual Edition 1.0
25
JetSpeed IAD-Wp2
User Manual Edition 1.0
Access Control Using the Access Control functionality, you can restrict or allow access
based on a MAC address. To set a MAC address type it in the relevant
address space or press the button Add Currently associated MAC Stations
to automatically set the MAC Address(es) of the already connected Wireless
Client Adapters. By Choosing Allow or Deny the Wireless clients where
MAC addresses belong to, will be allowed or denied accordingly to access
the Wi-Fi Access Point of JetSpeed IAD-Wp2.
26
JetSpeed IAD-Wp2
User Manual Edition 1.0
Security To make your wireless network safe, you should enable the security function.
The device supports the following security mechanisms:
WPA/WPA2
WPA2 Only
WEP
Disabled (no security)
WPS (Wireless Wi-Fi Protected Setup (WPS) is the industry standard method to simplify the
Protected security setup and management of Wi-Fi networks. You can easily setup and
Setup) connect to a WPA-enabled 802.11 network with WPS-certificated devices
using either Personal Information Number (PIN) or Push Button
Configuration (PBC) method. Legacy devices without WPS can be added to
the network using the traditional manual configuration method.
27
JetSpeed IAD-Wp2
User Manual Edition 1.0
28
JetSpeed IAD-Wp2
User Manual Edition 1.0
NAT Menu
Description Network Address Translation (NAT) allows multiple users at your local site to
access the Internet through a single public IP address or multiple public IP
addresses. NAT can also prevent hacker attacks by mapping local
addresses to public addresses for key services such as the Web or FTP.
Virtual Server If you configure the device as a virtual server, remote users accessing
services, such as web or FTP, at your local site (via public IP addresses) can
be automatically redirected to local servers configured with private IP
addresses. In other words, depending on the requested service (TCP/UDP
port number), JetSpeed IAD-Wp2 redirects the external service request to
the appropriate server (located at another internal IP address).
For example, if you set Type / Public Port to TCP / 80 (HTTP or web) and the
Private IP / Port to 192.168.1.2 / 80, then all HTTP requests from outside
users will be transferred to 192.168.1.2 on port 80. Therefore, just by
entering the IP address provided by the ISP, Internet users can access the
service they need at the local address to which you redirect them.
The most common TCP service ports include: HTTP (80), FTP (21), Telnet
(23) and POP3 (110).
29
JetSpeed IAD-Wp2
User Manual Edition 1.0
FIREWALL Menu
Network attacks that deny access to a network device are called Denial-of-
Service (DoS) attacks. DoS attacks are aimed at devices and networks with
a connection to the Internet. Their goal is not to steal information, but to
disable a device or network so users no longer have access to network
resources.
To enable the firewall, click Enable and then click the SAVE SETTINGS
button.
30
JetSpeed IAD-Wp2
User Manual Edition 1.0
Access Control The Access Control screen allows users to define the outgoing traffic
permitted or not-permitted through the WAN interface. JetSpeed IAD-Wp2
is set by default to permit all outgoing traffic.
Parameter Description
Enable Filtering Enables or Disables the Access Control function.
Function
Normal Filtering Displays a descriptive list of defined Filtering rules.
Table
Step Action
1 Click Add PC in the Access Control screen. The Access Control
Add PC screen appears.
2 Define the appropriate settings for client PC services. You can
choose any from the predefined services or you can create your own
by setting the appropriate TCP or UDP ports.
3 If Firewall Scheduling is enabled you can also choose the desired
schedule rule.Click the OK button and then click the SAVE
SETTINGS button to save your settings.
31
JetSpeed IAD-Wp2
User Manual Edition 1.0
MAC Filtering The MAC Filter allows you to define which client PCs can access the
Table Internet. When enabled, only the MAC addresses defined in the MAC
Filtering table will have access to the Internet. All other client devices will be
denied access.
Parameter Description
MAC Address Select Enable or Disable to enable or disable the
Control MAC filtering respectively.
MAC Filtering Enter the MAC address to be granted access in the
Table respective field.
URL Filter The URL filter allows the user to block access to web sites by entering either
a full URL address or just a keyword. This feature can be used to protect
children from accessing violent or pornographic web sites. You can define up
to 30 sites.
32
JetSpeed IAD-Wp2
User Manual Edition 1.0
Creating a URL To block selected client PCs from accessing various WEB Sites, proceed as
Filter rule follows:
Step Action
1 Select Access Control from the FIREWALL menu and press the
Add PC button.
2 Enter a description for the new rule and set the IP of the client(s)
PC where the rule will be applied to. Select a range of IPs or only
one as the example below. Enable the Blocking option in the
WWW with URL Blocking rule and press OK to create the new
rule.
3 Select URL blocking from the FIREWALL menu. Enter the
desired keyword or the complete URL from the site(s) you wish to
be blocked. A keyword could be part of the URL or words
contained in the URL. Please enter only one keyword or URL per
Rule number (up to 30 in total). When you finish entering the
keywords/URL, press SAVE SETTINGS button.
4 To test the new URL blocking rule try to enter in your browser
address bar a URL containing the keyword or the URL itself that
you wish to block. If the rule works, the following message will
appear on your browser window.
33
JetSpeed IAD-Wp2
User Manual Edition 1.0
Scheduling of JetSpeed IAD-Wp2 has the capability to filter Internet access for local
access rules clients based on rules. Each access control rule may be activated at a
scheduled time. Define the schedule in the Schedule Rule screen, and
apply the rule in the Access Control screen.
Step Action
1 Click Add Schedule Rule in the Schedule Rule screen. The Edit
Schedule Rule appears.
2 Define the appropriate settings for a schedule rule.
3 Click OK and then click SAVE SETTINGS to save your settings.
Intrusion The Incorporated firewall can block common hacker attacks, and provide
Detection protection against: IP Spoofing, Land Attack, Ping of Death, IP with zero
length, Smurf Attack, UDP port loopback, Snork Attack, TCP null scan, and
TCP SYN flooding.
When the SPI (Stateful Packet Inspection) firewall feature is enabled, all
packets can be blocked. Stateful Packet Inspection (SPI) allows full support
of different application types that are using dynamic port numbers.
34
JetSpeed IAD-Wp2
User Manual Edition 1.0
Intrusion
Detection
Screen
35
JetSpeed IAD-Wp2
User Manual Edition 1.0
USB Menu
Description The JetSpeed IAD-Wp2 implements a USB port which acts like a Host.
Enable this function and plug-in your USB device to share it with other
people in a network. The Supported devices are:
USB mass storage: Hard disk1, flash disk or single slot card reader1
USB Printer
USB Hub
Plug the device in the USB and its information will appear as displayed
below.
1
Support in Future Firmware Versions
36
JetSpeed IAD-Wp2
User Manual Edition 1.0
File Server This page allows you to configure the File Server features, to share files with
computers supporting the NetBIOS/SMB protocol.
Step Action
1 Connect the hard drive, flash disk, Hub to the USB port.
2 Create a shared folder by specifying the device and directory
(path) you want to share.
3 Specify the following parameters for each shared source:
Username
Password
Security Level
4 Enable the File Server function used to the folders by typing the
following URL in the IE browser or Windows Explorer:
\\(IP-Adresse) e.g. : \\192.168.1.1
\\(Server Name) e.g.: \\INTRACOM
\\(IP-Adresse)\(Folder name) e.g.: \\192.168.1.1\partition1
\\(Server Name)\(Folder name) e.g.:
\\INTRACOM\partition1
NOTE To access the USB storage from the WAN side, you need to
enable the Remote Access parameter and use the WAN IP
address to access this IAD.
37
JetSpeed IAD-Wp2
User Manual Edition 1.0
FTP Server This page allows the user to share any files/folders in your USB hard drive or
flash, using FTP.
Step Action
1 Specify the user profile and which partition/directory you want to
share.
2 Specify the different passwords and security levels for different
user profiles.
3 Enable the FTP Server function and use the following URL to
access the shared files/folders:
ftp://(IP address) e.g. ftp://192.168.1.1
To access the shared resource from the WAN side, you need
NOTE to enable the "Remote Access" parameter and use the WAN
IP to access it.
38
JetSpeed IAD-Wp2
User Manual Edition 1.0
Web FTP This page allows the user to share his USB mass storage via the HTTP
Server protocol.
Step Action
1 Enable this function by selecting the appropriate option box.
2 Configure the necessary parameters.
3 Access your USB storage from the LAN side by type the following
URLs:
http://(IP address):(port number) e.g. http://192.168.2.1:8000
http://(host name):(port number) e.g. http://INTRACOM:8000
http://(IP address) e.g. http://192.168.1.1/pt_usb
http://(host name) e.g. ex: http://INTRACOM/pt_usb
NOTE To access the USB storage from the WAN side, enable the
Remote Access parameter and use the first two URLs.
39
JetSpeed IAD-Wp2
User Manual Edition 1.0
Printer Server The JetSpeed IAD-Wp2 implements the LPD-LPR network protocol to
allow you to share your printer on your local or public network.
To do this proceed as follows:
Step Action
1 Select the Enable LPD-LPR Printer Server function option box:
40
JetSpeed IAD-Wp2
User Manual Edition 1.0
41
JetSpeed IAD-Wp2
User Manual Edition 1.0
Setting up a
printer in
Step Action
windows XP
(continued) 4 Select the Ports tab and press the Add Port button.
5 In the next dialog select Standard TCP/IP Port from the available
options and press New Port to start creating the new port.
42
JetSpeed IAD-Wp2
User Manual Edition 1.0
Setting up a
printer in
Step Action
windows XP
(continued) 6 The Add New Port wizard begins. Press Next to continue.
43
JetSpeed IAD-Wp2
User Manual Edition 1.0
Setting up a
printer in
Step Action
windows XP
(continued) 8 Select the Custom option and the press the Settings button.
9 Select the LPR protocol and type the Queue Name as in the
example below and press OK to continue.
NOTE In case you receive errors each time you try to print a
document, please enable LPR Byte counting
Enabled option.
44
JetSpeed IAD-Wp2
User Manual Edition 1.0
Setting up a
printer in
Step Action
windows XP
(continued) 10 The installation of the TCP/IP port has been completed. Press
Finish to close the Wizard and then press Close to exit the New
Port dialog screen.
11 The New TCP/IP port is now created and selected under the
Ports tab of your printer properties. Press Apply and Close to
exit from the printer properties window.
45
JetSpeed IAD-Wp2
User Manual Edition 1.0
TOOLS Menu
Description This menu allows you to backup and restore, JetSpeed IAD-Wp2
configuration.
Available The Configuration Tools screen includes the following configuration tools.
Configuration Select the one you want and click Next.
Tools
Backup Router Configuration: allows you to save the JetSpeed
IAD-Wp2 configuration to a file
Restore from saved Configuration file (backup bin): this function
is used to restore the previously saved backup configuration file.
Parameter Description
INTERNET Displays the type and the status of the connection to the
WAN.
Click the Release button to disconnect from the WAN.
Click the Renew button to establish connection to the
WAN.
GATEWAY Displays system IP settings, as well as DHCP Server
and firewall status.
INFORMATION Displays the number of attached clients, the firmware
versions, the physical MAC address for each media
interface and for JetSpeed IAD-Wp2, as well as the
hardware version and serial number.
ATM PVC Displays the ATM connection type and status.
Disabled means that the ATM connection is disabled.
Click the Connect button to establish an ATM
connection.
DHCP Client Log Displays information for DHCP clients on your network.
Status Log Displays important information and alarms.
46
JetSpeed IAD-Wp2
User Manual Edition 1.0
47
JetSpeed IAD-Wp2
User Manual Edition 1.0
Routing/Bridging Routing:
Features
- Static routing
- Static Routing per ATM Interface
- Dynamic Routing
- RIPv1, RIPv2
- IP Multicasting IGMP v2, v3
Bridging:
- WAN-LAN transparent bridging
- Transparent bridging between LAN devices
- Automatic discovery of MAC addresses
NAT - NAT-NAPT, RFCs 3022
- Port Forwarding
- Static NAT
- Static NAPT
- Application Level Gateway (ALGs) modules
- Public to Private IP 1-to-1 Mapping
QoS - ATM QoS: UBR, VBR-nrt, VBR-rt, CBR
- Diffserv (RFC2474, RFC2475) marking and queuing
according to connection type, network interface, MAC,
IP, hostname, DSCP/ ToS value, port number and
application
- WMM (IEEE 802.11e)
- Port based QoS
Voice over IP Codecs:
(VoIP) - G.711, G723.1, G.726, G729a
- G.168 Echo Cancellation
- DTMF relay using Sip Info packets
- G.711 fax pass through
- NOTIFY for voice mail
- VAD and GNC support
- T.38 Fax relay
Security - Firewall with SPI, intrusion logging and reporting
- WPA/WPA2 (IEEE 802.11i)
- Denial of service (DoS) protection NAT
- Static routing
- Static IP address assignment, Dynamic Routing
- Wireless: WPA2-PSK, WPA-PSK, WEP, WPA-802.1x,
WPA2-802.1x
Remote - Web UI (admin and user)
Management - Telnet/CLI
- TR-069, TR-104, TR-98, TR-111
48
JetSpeed IAD-Wp2
User Manual Edition 1.0
Environmental The following table provides the environmental specifications of the device:
Specifications
Input Voltage The following table provides the electrical specifications of the device:
Requirements
49
JetSpeed IAD-Wp2
User Manual Edition 1.0
Question Answer
Q1: A1:
How do I reset JetSpeed IAD- Using the option Restore Router to Factory
Wp2 to Factory Defaults? Defaults under TOOLS > Configuration Tools
menu. Alternatively, you can press reset button in
the back panel of JetSpeed IAD-Wp2 for
approximately 5 seconds.
Q2: A2:
Up to a maximum of 254 computers.
How many computers on the
LAN does JetSpeed IAD-Wp2
Note: The Quality of Service (QoS) is related to the
support?
guaranteed level of throughput (the amount of data
transferred from the Router to the clients). As many
clients are connected as lower is the Quality as
Service.
Q3: A3:
Q4: A4:
How are additional computers You can expand the number of connections
connected? available on your LAN by using hubs, switches and
wireless access points connected to the Router.
50
JetSpeed IAD-Wp2
User Manual Edition 1.0
Appendix C: Troubleshooting
51
JetSpeed IAD-Wp2
User Manual Edition 1.0
52
JetSpeed IAD-Wp2
User Manual Edition 1.0
NOTE: All your configuration changes will be lost, and you will need
to configure your network again before you can re-establish your
connection to the Internet. Also, other computer users will lose their
network connections, whilst this process is taking place, so choose
an hour when this would be convenient.
53
JetSpeed IAD-Wp2
User Manual Edition 1.0
Ensure that the TCP/IP settings for all devices are correct.
Ensure that the Wireless Clients are using the same SSID or
Service Area Name as JetSpeed IAD-Wp2. The SSID is
case-sensitive.
Ensure that the encryption method and level that you use on
your clients are the same as those configured on JetSpeed
IAD-Wp2. Simultaneous WPA and WEP encryption is not
supported.
54
JetSpeed IAD-Wp2
User Manual Edition 1.0
55
JetSpeed IAD-Wp2
User Manual Edition 1.0
56
Za vie informacija