Professional Documents
Culture Documents
MB Installation Guide-Eu
MB Installation Guide-Eu
The
English
installation instructions below apply to GIGABYTE's desktop systems and are for reference
only.
Refer to the user's manual included for detailed motherboard specifications.
Before installing the devices, make sure they are compliant with the connectors on your computer.
Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord
from the power outlet to prevent damage to the devices and the system components.
Place the computer system on a stable surface to prevent improper installation resulted from shaking.
Step
A. Installing an Intel CPU (skip this step if the motherboard has a built-in CPU)
A-1 Refer to the following instructions based on your CPU specifications:
Type A:
Lift the CPU socket lever and the metal load plate will be lifted as well.
a. If the protective socket cover is fastened on the CPU socket, remove
it first.
b. If the protective socket cover is fastened on the metal load plate, do
not remove it at this stage. The socket cover may pop off from the
load plate automatically during the process of re-engaging the lever
after you insert the CPU.
Type B:
Push lever A (closest to the " " marking) down and away from the socket to release it. Then push
lever B (closest to the " " marking) down and away from the socket and lift it. Gently press lever A to
allow the load plate to rise. Open the load plate.
Lever A Lever B
A-2 Hold the CPU with your thumb and index fingers. Align the CPU pin one marking (triangle) with the pin
one corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and
gently insert the CPU into position.
A-3 Once the CPU is properly inserted, replace the load plate and push the CPU socket lever back into its locked position.
Once the type B is properly inserted, carefully replace the load plate. Then secure lever B under its retention
tab. The socket cover may pop off from the load plate during the process of engaging the lever. Finally,
secure lever A under its retention tab to complete the installation of the CPU.
For detailed instructions on installing the CPU, please refer to the users manual.
-1-
B. Installing an AMD CPU (skip this step if the motherboard has a built-in CPU)
English
B-1 Completely raise the CPU socket lever. Align the CPU pin
one (small triangle marking) with the triangle marking on the CPU Socket Lever
CPU socket and gently insert the CPU into the socket. Make
sure that the CPU pins fit perfectly into their holes.
B-2 Once the CPU is positioned into its socket, place one finger
down on the middle of the CPU, lowering the socket lever
and latching it into the fully locked position.
CPU Socket Pin 1
Do not force the CPU into the CPU socket. The CPU cannot fit in if oriented incorrectly. Adjust the CPU
orientation if this occurs.
DO NOT touch socket contacts. To protect the CPU socket, always replace the protective socket cover
when the CPU is not installed.
Step
2 Installing Memory
Note the orientation of the memory module. Spread the retaining clips at both ends
of the memory socket. Place the memory module on the socket. As indicated in the
picture on the left, place your fingers on the top edge of the memory, push down on
the memory and insert it vertically into the memory socket. The clips at both ends
of the socket will snap into place when the memory module is securely inserted.
Step
Using the GIGABYTE desktop system as the demonstration example, please first
remove both sides and the lid of the case in order to install the power supply.
Place the power supply in the correct place in the case and secure it with screws.
Installation and placement of the power supply may differ depending on the type
of case used.
To ensure sufficient power can be supplied to your system, it is
recommended that a power supply of good quality be used. If a power
supply is used that does not provide the required power, the result can
lead to an unstable or unbootable system.
-2-
English
Step
Remove the original I/O shield from the back of the case and replace it with the
motherboard I/O shield. Place the motherboard within the case by positioning it
into its I/O shield. Align the mounting screw holes on the motherboard with their
corresponding mounting holes on the case. Secure the motherboard in place
with screws.
I/O Shield
Step
Locate an expansion slot that supports your card and remove the slot cover from
the case back panel. Then insert the expansion card into the slot. Secure the
expansion card's bracket to the case back panel with a screw.
Before purchasing an expansion card, check the length of the card, making
sure it can fit into your case.
PCI Express Graphics Card Make sure that the expansion card is fully seated in its slot.
Step
6-1 Install your optical drives, such as DVD-ROM and CD-ROM drives.
Remove the 5.25" drive bay cover from the front of the case. Mount the optical drive
in the 5.25" drive bay and secure it with screws.
One motherboard IDE connector can connect up to two IDE devices. Prior to installation, check the jumper
settings (master and slave) on your IDE devices.
If more than one hard drive is installed, enter system BIOS Setup to set the hard drive boot sequence.
-3-
English
Step
7-1 Connect cables to internal connectors and headers on the motherboard, including IDE/SATA
connectors, and front panel audio, USB, IEEE 1394 headers, etc.
7-2 Attach the front panel module (differs depending on the case design, consisting of power
indicator, hard drive activity indicator, speakers, reset switch, power switch, etc.) from the case
to the front panel header (F_PANEL) on the motherboard.
Pin Assignments A: Pin Assignments B: MSG: Message/Power/Sleep LED
+MSG- +PW- +SPEAK- +MSG- +PW- +SPEAK- PWR: Power LED
PW: Power Switch
2 20 SPEAK: Speaker
1 19 HD: Hard Drive Activity LED
+HD- -RES+ +HD- -RES+ -CI+ +PWR- RES: Reset Switch
Front Panel Header NC CI: Chassis Intrusion Header
(Note) The pin assignments for the front panel header may differ by model. Refer
to the motherboard user's manual for the actual pin assignments.
Step
8 Connecting Peripherals
Back Panel of the Case
Power Supply Power Switch Once the steps above have been completed, connect
PS/2 Keyboard Port Power Cord Connector the peripheral devices to the computer, such as the
keyboard, mouse, monitor, etc. Then connect the power,
DVI-D Port PS/2 Mouse Port
turn on the system, and install all required software.
HDMI Port D-Sub Port
-4-
Die Installationsreihenfolge kann je nach Typ des verwendeten Gehuses sowie der verwendeten Gerte
variieren. Die folgenden Installationsanweisungen betreffen Desktop-Systeme von GIGABYTE und
dienen nur als Referenz.
Schlagen Sie bitte ausfhrliche technische Daten des Motherboards im beigelegten Benutzerhandbuch nach.
Stellen Sie vor der Installation von Gerten sicher, dass Ihre Gerte mit den Anschlssen Ihres Computers
kompatibel sind.
Schalten Sie immer vor dem Installieren die Gerte und Ihren Computer aus. Trennen Sie den Rechner vom
Stromnetz, um Schden an den Gerten und den Systemkomponenten zu vermeiden.
Stellen Sie das Computersystem auf eine stabile Unterlage, damit die Installation nicht durch Wackeln
beeintrchtigt wird.
Schritt
Deutsch
A. Installieren einer Intel CPU (berspringen Sie diesen Schritt, wenn das Motherboard ber einen
eingebauten Prozessor verfgt)
A-1 Beachten Sie die folgenden Anweisungen basierend auf Ihren CPU-Spezifikationen:
Typ A:
Heben Sie den CPU-Sockelhebel an, dadurch hebt sich auch die
Metallladeplatte.
a. Falls die Sockelschutzabdeckung am CPU-Sockel befestigt ist,
entfernen Sie sie zunchst.
b. Falls die schtzende Sockelabdeckung an der Metallandruckplatte
befestigt ist, nehmen Sie sie jetzt noch nicht ab. Die Sockelabdeckung
kann sich beim Wiederanziehen des Hebels nach Einsetzen der CPU
von selbst lsen.
Typ B:
Drcken Sie Hebel A (der Markierung am nchsten) nach unten und vom Sockel weg, um ihn
zu lsen. Drcken Sie dann Hebel B (der Markierung am nchsten) nach unten und vom Sockel
weg und heben Sie ihn an. Drcken Sie behutsam Hebel A, um den Deckrahmen anzuheben. ffnen
Sie den Deckrahmen.
Hebel A Hebel B
A-2 Halten Sie die CPU mit Daumen und Zeigefinger. Richten Sie die (Dreieck-) Markierungen fr Pin 1 auf
der CPU und die Pin 1-Ecke des CPU-Sockels aufeinander aus. (Sie knnen ebenfalls die CPU-Kerben
auf die Ausrichtungsnasen des Sockels ausrichten.) Legen Sie dann vorsichtig die CPU in der richtigen
Position ein.
A-3 Legen Sie den Schutzrahmen wieder auf und stellen den CPU-Sockelhebel in seine Arretierposition zurck,
sobald die CPU richtig sitzt.
Bringen Sie den Deckrahmen nach dem ordnungsgemen Einsetzen der typ B vorsichtig wieder an.
Sichern Sie anschlieend Hebel B unter dessen Befestigungsnase. Die Sockelabdeckung kann sich beim
Bettigen des Hebels vom Deckrahmen lsen. Sichern Sie zuletzt Hebel A unter dessen Befestigungsnase,
um die Installation der CPU abzuschlieen.
Detaillierte Anweisungen zur CPU-Installation entnehmen Sie bitte der Bedienungsanleitung.
-1-
B. Installieren einer AMD CPU (berspringen Sie diesen Schritt, wenn das Motherboard ber einen
eingebauten Prozessor verfgt)
B-1 Ziehen Sie den CPU-Sockelhebel ganz nach oben. CPU-Sockel-hebel
Richten Sie den Pin 1 der CPU (mit einem kleinen Dreieck
gekennzeichnet) auf die Dreieck-Markierung am CPU-Sockel
aus und legen Sie dann vorsichtig die CPU ein. Stellen Sie
sicher, dass die Pins der CPU perfekt in die ffnungen
passen.
B-2 Wenn die CPU richtig in dem Sockel sitzt, legen Sie bitte einen CPU-Sockel Pin 1
Deutsch
Finger auf die Mitte der CPU, drcken den Sockelhebel nach
unten und bringen ihn in seine Arretierposition zurck.
Stecken Sie die CPU nicht mit Gewalt in den CPU-Sockel. Die CPU lsst sich nicht einpassen, wenn die
Ausrichtung falsch ist. ndern Sie in diesem Fall die Ausrichtung der CPU.
Berhren Sie NICHT die Sockelkontakte. Setzen Sie die Schutzabdeckung grundstzlich wieder auf,
wenn keine CPU installiert ist. Dies schtzt den Sockel vor Beschdigungen.
2
Schritt
Achten Sie auf die korrekte Ausrichtung des Speichermoduls. Drcken Sie die
Haltebgel an beiden Enden des Speichersteckplatzes nach auen. Stecken
Sie das Speichermodul in den Steckplatz ein. Legen Sie wie links abgebildet
Ihre Finger auf die obere Kante des Speichermoduls und drcken das Modul
nach unten, damit es senkrecht im Speichersteckplatz sitzt. Die Haltebgel an
beiden Enden des Steckplatzes rasten ein, wenn das Speichermodul richtig
eingesteckt wurde.
Schritt
-2-
Schritt
Entfernen Sie die ursprngliche E/A-Blende von der Rckseite des Gehuses und
ersetzen Sie sie durch die dem Motherboard beigelegte E/A-Blende. Legen Sie das
Motherboard in das Gehuse ein, wobei die E/A-Anschlsse auf die E/A-Blende
ausgerichtet werden mssen. Richten Sie die Schraubenlcher am Motherboard
auf die entsprechenden Befestigungslcher am Gehuse aus. Befestigen Sie das
Motherboard mit Schrauben am Gehuse.
Deutsch
I/O-Blende
Schritt
Whlen Sie einen Steckplatz, der Ihre Karte untersttzt. Entfernen Sie die
entsprechende Steckplatzblende an der Rckseite des Gehuses. Stecken Sie
dann die Erweiterungskarte in den Steckplatz ein. Fixieren Sie den Bgel der
Karte mit einer Schraube an der Gehuserckwand.
Informieren Sie sich vor dem Kauf ber die Lnge der Karte; berzeu-
gen Sie sich davon, dass sie in das Gehuse passt.
PCI Express Grafikkarte Stellen Sie sicher, dass die Erweiterungskarte richtig im Steckplatz sitzt.
Schritt
6-1 Installieren Sie Ihre optischen Laufwerke wie z.B. DVD- oder CD-Laufwerke.
Entfernen Sie die Blende des 5,25-Laufwerkfachs von der Frontseite des
Gehuses. Legen Sie das optische Laufwerk in das 5,25 Laufwerkfach ein und
befestigen es mit Schrauben.
Installieren eines optischen Laufwerks
Mit einem IDE-Anschluss am Motherboard knnen zwei IDE-Gerte verbunden werden. Prfen Sie bitte
vor der Installation die Jumpereinstellungen (Master und Slave) an Ihren IDE-Gerten.
Wenn mehr als eine Festplatte installiert ist, rufen Sie bitte das System-BIOS-Einstellungsprogramm auf
und stellen die Bootreihenfolge der Festplatten ein.
-3-
Schritt
7-1 Verbinden Sie Kabel mit den entsprechenden Anschlssen und Sockel am Motherboard inklusive IDE/
SATA-Anschlsse, Front-Audio, USB, IEEE 1394 usw.
7-2 Verbinden Sie das Front Panel-Modul (es besteht je nach Gehusedesign aus einer Strom-LED, einer
Festplattenaktivitts-LED, einem Lautsprecher, einem Reset-Schalter, einem Stromschalter usw.) am
Gehuse mit dem Front Panel-Anschluss (F_PANEL) am Motherboard.
Deutsch
Schritt
Externe Grafikkarte
-4-
El proceso de instalacin puede variar dependiendo del tipo de CAJA y dispositivos utilizados. Las
instrucciones de instalacin que aparecen a continuacin son de aplicacin para ordenadores de escritorio
GIGABYTE y slo a modo de referencia.
Consulte el manual de usuario incluido para obtener especificaciones detalladas sobre la placa madre.
Antes de instalar los dispositivos, asegrese de que sean compatibles con los conectores del ordenador.
Antes de instalar los dispositivos, asegrese de apagar los dispositivos y el ordenador. Desconecte el cable
de alimentacin de la toma de corriente para evitar daar los dispositivos y los componentes del sistema.
Coloque la ordenador sobre una superficie estable para evitar que movimientos bruscos causen una
instalacin incorrecta.
Paso
A. Instalacin de un procesador Intel (omita este paso si la placa base tiene una CPU integrada)
A-1 Consulte las siguientes instrucciones basadas en las especificaciones de la CPU:
Tipo A:
Levante completamente la palanca del zcalo de la CPU y la placa
metlica de carga tambin se levantar.
a. Si la tapa del zcalo de proteccin est sujeta al zcalo de la CPU,
qutela primero.
Espaol
b. Si la tapa protectora del zcalo est sujeta a la placa de carga
metlica, no la quite en este momento. La tapa del zcalo puede
desprenderse de la placa de carga automticamente durante el
proceso de reengarce de la palanca despus de insertar la CPU.
Tipo B:
Presione la palanca A (la ms cercana a la marca " ") hacia abajo desplazndola del zcalo para
liberarla. Presione la palanca B (la ms cercana a la marca " ") hacia abajo desplazndola del zcalo
y levntela. Presione suavemente la palanca A para levantar la chapa metlica. Levante la chapa.
La palanca A La palanca B
A-2 Sostenga el procesador con los dedos pulgar e ndice. Alinee la marca de la clavija 1 del procesador
(tringulo) con la esquina de la clavija 1 del socket del procesador (o puede alinear las muescas del
procesador con las muescas de alineacin del socket) e inserte con cuidado el procesador.
A-3 Una vez que el procesador se encuentre insertado de forma correcta, vuelva a instalar la cubierta de
proteccin y baje la palanca del socket del procesador y colquela en la posicin de bloqueo.
Cuando la tipo B est correctamente insertada, vuelva a colocar con cuidado la placa metlica. A
continuacin, asegure la palanca B debajo de su lengeta de retencin. La chapa del zcalo podra
desprenderse durante el proceso de sujecin de la palanca. Finalmente, asegure la palanca A debajo de
su lengeta de sujecin para completar la instalacin de la CPU.
Para obtener instrucciones detalladas sobre cmo instalar la CPU, consulte el manual del usuario.
-1-
B. Instalacin del procesador AMD (omita este paso si la placa base tiene una CPU integrada)
B-1 Levante por completo la palanca del socket del procesador.
Alinee la clavija 1 del procesador (marca con un tringulo Palanca del socket del procesador
pequeo) con la marca con un tringulo en el socket del
procesador e inserte con cuidado el procesador en el socket.
Asegrese de que las clavijas del procesador encajen en forma
correcta en los orificios.
-2-
Paso
Protector de E/S
Paso
Busque una ranura de expansin que sea compatible con la tarjeta y retire
la tapa de la ranura ubicada en el panel trasero de la caja. Luego, inserte
la tarjeta de expansin en la ranura. Asegure el soporte de la tarjeta de
Espaol
expansin al panel trasero del de la caja utilizando un tornillo.
Antes de adquirir una tarjeta de expansin, verifique la longitud de la
tarjeta para asegurarse de que pueda ser colocada en el la caja.
Tarjeta grfica PCI Express Asegrese de que la tarjeta de expansin quede insertada por completo
en la ranura.
Paso
Se puede conectar hasta dos dispositivos IDE en un conector IDE de la placa madre. Antes de realizar la
instalacin, compruebe la configuracin de los jumpers (principal y secundario) de los dispositivos IDE.
Si se instala ms de un disco duro, acceda al BIOS Setup (Configuracin del BIOS) del sistema para
establecer la secuencia de inicio de los discos duros.
-3-
Paso
7-1 Conecte los cables en los conectores y conexiones internas de la placa madre, incluidos los conectores
IDE/SATA, audio del panel frontal, USB, IEEE 1394, etc.
7-2 Conecte el mdulo del panel frontal (diferente segn el diseo de la caja y compuesto por un indicador
de encendido, indicador de actividad de disco duro, altavoces, interruptor de reinicio, interruptor de
encendido/apagado, etc.) de la caja a la conexin (F_PANEL) ubicada en la placa madre.
Asignaciones de clavijas A: Asignaciones de clavijas B: MSG: LED de mensajes/encendido/
suspensin
+MSG- +PW- +SPEAK- +MSG- +PW- +SPEAK- PWR: LED de encendido
PW: Interruptor de encendido/apagado
2 20
SPEAK: Altavoces
1 19 HD: LED de actividad de disco duro
Paso
8 Conexin de perifricos
Espaol
-4-
A sequncia pela qual a instalao feita pode variar conforme o tipo de caixa e os dispositivos
usados. As instrues de instalao embaixo aplicam-se aos sistemas desktop da GIGABYTE e
servem apenas como referncia.
Consulte o manual do utilizador includo juntamente com a placa principal para obter as
especificaes desta.
Antes de instalar os dispositivos, certifique-se de que estes so compatveis com os conectores
existentes no seu computador.
Antes de instalar os dispositivos, certifique-se de que os dispositivos esto desligados no seu
computador. Retire o cabo de alimentao da tomada eltrica para evitar danos ao dispositivos e
os componentes do sistema.
Coloque o computador sobre uma superfcie estvel para evitar uma instalao incorrecta devido
a instabilidade do mesmo.
Etapa
Portugus
A alavanca A A alavanca B
A-2 Segure na CPU com o polegar e o dedo indicador. Alinhe o pino 1 da CPU (marca de tringulo) com o
canto do socket (ou pode alinhar os entalhes existentes na CPU com as chaves de alinhamento existentes
no respectivo socket) e posicione cuidadosamente a CPU na posio correta.
A-3 Quando a CPU estiver devidamente instalada, reponha a placa de carga e empurre a alavanca do socket
da CPU para que esta retome a sua posio original.
Aps inserir corretamente a tipo B, volte a fechar cuidadosamente a placa de conteno. Em seguida, fixe
a alavanca B abaixo da aba de reteno. A tampa do socket poder saltar da placa de carregamento ao
acionar a alavanca. Por fim, fixe a alavanca A debaixo da aba de reteno para concluir a instalao da CPU.
Consulte o manual do utilizador para obter instrues detalhadas acerca da instalao da CPU.
-1-
B. Instalao de uma CPU AMD (avance este passo se a placa principal possuir uma CPU incorporada)
B-1 Levante completamente a alavanca do socket da CPU.
Alinhe o pino 1 da CPU (marca de tringulo) com a marca Alavanca do socket da CPU
de tringulo existente no socket da CPU e posicione
cuidadosamente a CPU no socket. Certifique-se de que os
pinos da CPU ficam bem encaixados nos respectivos orifcios.
2
Etapa
Instalao Da Memria
Etapa
-2-
Etapa
Espelho I/O
Etapa
Etapa
Portugus
6-1 Instale as suas unidades pticas como, por exemplo, unidade de DVD-ROM e CD-
ROM. Remova a tampa do compartimento da unidade de 5,25 a partir da parte da
frente da caixa. Instale a unidade ptica no compartimento de 5,25 e fixe-a com
parafusos.
Um conector IDE da placa principal permite a ligao de um mximo de dois dis positivos IDE. Antes da
instalao, verifique as definies dos jumpers (principal e secundrio) do seus dispositivos IDE.
Se tiver mais do que uma unidade de disco rgido instalada, entre na pgina de configurao do BIOS para
definir a sequncia de arranque das unidades de disco rgido.
-3-
Etapa
Etapa
-4-
La squence dinstallation peut diffrer selon le type de boitier et de matriels utiliss.
Les instructions dinstallation ci-dessous sappliquent aux systmes de bureaux GIGABYTE et
servent uniquement de rfrence.
Consultez le guide dutilisation inclus pour des spcifications dtailles de la carte mre.
Avant dinstaller les composants, assurez vous que votre matriel est compatible avec les
connecteurs de votre ordinateur.
Avant dinstaller les appareils, assurez-vous dteindre les appareils et votre ordinateur. Dbranchez
le cordon dalimentation de la prise de courant pour viter dendommager les appareils et les
composants du systme.
Placez lordinateur sur une surface stable pour viter quil ne soit secou suite une installation
inapproprie.
Etape
A-2 Tenez le processeur entre votre pouce et votre index. Alignez la marque (triangle) de la broche un du
processeur avec le coin de la broche un de la prise du processeur (ou bien alignez les encoches du
Franais
processeur avec les cls dalignement de la prise) et insrez doucement le processeur en place.
A-3 Une fois que le processeur est correctement insr, remplacez la plaque de charge et repoussez le levier
dans la position de blocage.
Une fois que le type B a t install correctement, remettez la plaque de maintient en faisant attention.
Puis remettez le levier B en position. Le couvercle du socket sera enlev de la plaque de maintient
pendant le processus d'engagement du levier. Enfin, remettez le levier A en position initiale pour terminer
l'installation du CPU.
Pour des instructions dtailles sur l'installation du CPU, veuillez vous rfrer au manuel
d'utilisation.
-1-
B. Installation dun processeur AMD (sautez cette tape si la carte mre comprend un CPU intgr)
B-1 Montez fond le levier le levier du support processeur.
Alignez la broche un du processeur (petit triangle) avec Levier du support processeur
le triangle situ sur la prise du processeur et insrez
doucement le processeur. Assurez-vous que les broches du
processeursadaptent parfaitement dans leurs trous.
2 Installation De La Mmoire
Notez lorientation du module de la mmoire. Enclenchez les attaches de
rtention aux deux extrmits de la prise de la mmoire. Placez le module de
mmoire sur la prise. Placez, de la faon indique sur limage de gauche, vos
doigts sur le bord suprieur de la mmoire, poussez la mmoire vers le bas et
insrez-la verticalement dans la prise de la mmoire. Les attaches situes aux
deux extrmits de la prise se refermeront en place une fois que le module de
la mmoire est correctement insr.
Etape
-2-
Etape
Etape
Reprez une fente dextension qui accepte votre carte puis retirez le couvercle
de la fente du panneau arrire du botier. Insrez ensuite la carte dextension
dans la fente. Fixez le support de la carte dextension sur le panneau arrire
du botier laide dune vis.
Avant dacheter une carte dextension, vrifiez la longueur de la carte,
en vous assurant quelle est adapte votre botier.
Carte graphique PCI Express
Assurez-vous que carte dextension est compltement enfonce dans
la fente.
Etape
Un connecteur de carte mre IDE peut connecter jusqu deux appareils IDE. Avant linstallation, vrifiez
les rglages du cavalier (matre et esclave) de vos appareils IDE.
Si plus dun disque dur est install, entrez dans les Rglages BIOS du systme pour configurer la
squence de lancement du disque dur.
-3-
Etape
(Remarque) Les emplacements de broche du panneau avant peuvent tre diffrentes de ceux
indiqus sur le schma. Consultez le mode demploi de la carte mre pour trouver
lemplacement rel des broches.
Etape
Alimentation lectrique Interrupteur Une fois que vous avez termin les tapes
Port pour clavier PS/2 Connecteur du cordon
dalimentation
ci-dessus, reliez les appareils priphriques
Port DVI-D Port pour souris PS/2 lordinateur, comme le clavier, la souris, le moniteur,
Port HDMI Port D-Sub
etc. Connectez ensuite lalimentation, allumez le
Ports eSATA Connecteur S/PDIF
systme et installez tous les logiciels requis.
Port IEEE1394 Ports USB
-4-
La sequenza dellinstallazione pu differire a seconda del tipo di case e dei dispositivi utilizzati. Le
istruzioni per linstallazione indicate in basso si applicano ai sistemi desktop GIGABYTE e sono
solo di riferimento.
Per specifiche dettagliate sulla scheda madre, fare riferimento al manuale utente incluso.
Accertarsi che i dispositivi siano conformi ai connettori sul computer, prima di installarli.
Prima dellinstallazione, accertarsi che i dispositivi e il computer siano spenti. Scollegare il cavo
elettrico dalla presa per evitare di danneggiare i dispositivi e i componenti del sistema.
Posizionare il computer su una superficie stabile per ovviare ai problemi di un'installazione non
corretta dovuta a oscillazioni.
Fase
A. Installazione di una CPU Intel (saltare questa fase se la scheda madre ha una CPU integrata)
A-1 Fare riferimento alle seguenti istruzioni in base alle specifiche della CPU:
Tipo A:
Sollevare la leva del socket della CPU e la piastra metallica si solleva
allo stesso modo.
a. Se il coperchio del socket protettivo fissato al socket della CPU,
necessario prima rimuoverlo.
b. Se la copertura della presa dalla piastra protettiva fissata sulla
piastra di carico in metallo, non rimuoverla in questa fase. La
copertura della presa potrebbe apparire automaticamente fuori dalla
piastra di carico durante il processo di reinnesto della leva dopo aver
inserito la CPU.
Tipo B:
Abbassare la leva A (la pi vicina al contrassegno " ") allontanandola dal socket per sganciarlo.
Quindi abbassare la levetta B (la pi vicina al contrassegno " ") allontanandola dal socket e alzare.
Premere delicatamente sulla leva A per consentire alla placchetta di fermo di alzarsi. Aprire la placchetta.
La levetta A La levetta B
A-2 Afferrare la CPU con il pollice e l'indice. Allineare il segno del pin uno della CPU (triangolo) con langolo
del pin uno dellalloggiamento (oppure allineare le tacche della CPU ai segni sullalloggiamento) e inserire
delicatamente la CPU al suo posto.
A-3 Una volta inserita correttamente la CPU, rimettere la piastra e spingere indietro la leva dellalloggiamento
in posizione di blocco.
Una volta correttamente inserita la tipo A, riposizionare con cura la placchetta di fermo. Quindi fissare la
levetta B sotto la sua linguetta di arresto. Il coperchio del socket pu saltar fuori dalla placchetta di fermo
durante l'operazione di aggancio della leva. Infine, per completare l'installazione della CPU, spingere la
leva A sotto la sua linguetta di arresto.
Per istruzioni dettagliate sull'installazione della CPU, fare riferimento al manuale dell'utente.
Italiano
-1-
B. Installazione di una CPU AMD (saltare questa fase se la scheda madre ha una CPU integrata)
B-1 Sollevare completamente la leva dellalloggiamento della
CPU. Allineare il pin uno della CPU (simbolo del triangolino) Leva dellalloggiamento della CPU
con il segno del triangolo sullalloggiamento ed inserire
delicatamente la CPU. Accertarsi che i pin della CPU si
inseriscano perfettamente nei fori.
Non forzare la CPU nellalloggiamento. La CPU non pu essere inserita, se orientata in maniera errata. In
questo caso, orientare correttamente la CPU.
NON toccare i contatti dellalloggiamento. Per proteggere lalloggiamento della CPU, riposizionare sempre
le coperture di protezione quando la CPU non installata.
2
Fase
3
Fase
-2-
4
Fase
Schermo I/O
5
Fase
6
Fase
Un connettore IDE della scheda madre pu collegare fino a due dispositivi IDE. Prima dellinstallazione
controllare le impostazioni dei jumper (master e slave) sui dispositivi IDE.
Se installato pi di un disco rigido, accedere al BIOS Setup del sistema per impostare la sequenza di
avvio del disco rigido.
Italiano
-3-
7
Fase
7-1 Collegare i cavi ai connettori interni e ai connettori sulla scheda madre, inclusi i connettori IDE/SATA e
quelli dellaudio del pannello frontale, USB, IEEE 1394 ecc.
7-2 Collegare il modulo del pannello frontale (diverso a seconda della struttura del case e che composto
da spia di alimentazione, spia dellattivit del disco rigido, altoparlanti, tasto di reset, tasto di accensione,
ecc.) dal case al connettore del pannello frontale (F_PANEL) sulla scheda madre.
Assegnazioni pin A: Assegnazioni pin B: MSG: LED Messaggio/Alimentazione/
Sleep
+MSG- +PW- +SPEAK- +MSG- +PW- +SPEAK-
PWR: LED alimentazione
2 20 PW: Interruttore di alimentazione
1 19 SPEAK: Altoparlante
HD: LED di attivit del disco rigido
+HD- -RES+ +HD- -RES+ -CI+ +PWR- RES: Tasto reset
Connettore del pannello frontale NC C.I.: Collettore di intrusione dello chassis
(Nota) Le assegnazioni dei pin del pannello frontale possono differire da modello a modello. Fare riferimento
al manuale utente della scheda madre per le assegnazioni reali dei pin.
8
Fase
Periferiche Di Connessione
Pannello posteriore del telaio
Alimentatore
Interruttore di Una volta completate le fasi di cui sopra, collegare
alimentazione
Porta della tastiera Connettore del cavo
le periferiche come tastiera, mouse, monitor ecc.,
PS/2 di alimentazione al computer. Quindi collegare lalimentazione,
Porta del mouse
Porta DVI-D
PS/2
accendere il sistema e installare il software
Porta HDMI
Porta D-Sub
necessario.
Porte eSATA
Connettore S/PDIF
Porta IEEE1394
Porte USB
Jack audio
Porta LAN RJ-45
Scheda grafica
esterna
Italiano
-4-
.
GIGABYTE .
.
6,
.
.
.
.
,
.
.
Intel ( ,
)
A-1 , :
:
,
a. ,
.
b.
, .
.
B:
( " ") ,
. ( " ")
, , .
, . .
A B
A-2 , 1-
1- (
) .
A-3 , , ,
.
B
. .
. ,
.
.
-1-
. AMD ( ,
)
B-1
. 1-
. ,
.
.
C-1
.
(
) .
C-2 CPU_
FAN .
.
. DIMM-
.
, ,
. ,
.
GIGABYTE.
, .
.
.
,
.
,
.
-2-
/
/
. ,
/.
.
.
/
,
.
. .
.
PCI Express
() ,
.
, .
6 IDE- SATA-
IDE IDE-.
IDE-
(master slave).
,
BIOS Setup , .
-3-
()
. F_PANEL
.
c ,
PS/2 : , , ..
DVI-D
PS/2
HDMI ,
D-Sub
eSATA .
S/PDIF
IEEE 1394
USB
RJ-45
-4-
Kolejno instalacji moe si rni w zalenoci od typu obudowy oraz instalowanych urzdze.
Ponisza kolejno instalacji zostaa pokazana na przykadzie systemu GIGABYTE i suy jedynie
celom informacyjnym.
W celu uzyskania dokadnej specyfikacji pyty gwnej, prosz skorzysta z instrukcji uytkownika.
Przed zainstalowaniem urzdze, upewnij si e s one kompatybilne ze zczami w twoim
komputerze.
Przed instalacj urzdze upewnij si e zarwno one jak i komputer s wyczone. Odcz kabel
zasilajcy od zasilacza by unikn uszkodzenia sprztu.
Umie komputer na stabilnej powierzchni by unikn nieprawidowej instalacji bdcej wynikiem
wstrzsw.
Krok
Polski
Instalacja procesora i wentylatora procesora
A. Instalacja procesora Intel (moesz pomin ten etap, jeli Twoja pyta gwna posiada
zintegrowany procesor)
A-1 Zapoznaj si z poniszymi instrukcjami w oparciu o specyfikacj procesora:
Typ A:
Unie dwigni gniazda procesora, metalowa osona rwnie zostanie
podniesiona.
a. Jeeli pytka zabezpieczajca gniazdo procesora jest zamocowana
do gniazda, naley j najpierw usun.
b. Jeeli pytka zabezpieczajca gniazdo procesora jest zamocowana do
gniazda, nie naley jej usuwa na tym etapie. Pytka zabezpieczajca
gniazdo procesora moe automatycznie odskoczy od gniazda
podczas procesu zakadania dwigni po umieszczeniu procesora.
Typ B:
Nacinij w d i w bok dwigni A (najbliej oznaczenia " "), aby otworzy socket. Nastpnie nacinij
w d i w bok dwigni B (najbliej oznaczenia " "). Delikatnie nacinij dwigni A, aby pozwoli
metalowej osonie unie si.
Dwigni A Dwigni B
A-2 Trzymajc pewnie procesor pomidzy kciukiem a palcem wskazujcym wyrwnaj may zoty trjkt na
brzegu procesora z rogiem wskazujcym pin pierwszy na gniedzie procesora (lub zrwnaj wcicia na
procesorze z naciciami na zczu) i delikatnie w procesor do gniazda.
A-3 Gdy procesor jest ju prawidowo osadzony, naley umieci na nim pytk zabezpieczajc i przesun
dwigni gniazda procesora z powrotem do pozycji zamknitej.
Kiedy procesor typ B jest prawidowo woony, delikatnie wycignij pytk. Zabezpiecz dwigni B. Osona
socketu moe odskoczy w momencie unoszenia dwigni. Na koniec zabezpiecz dwigni A w celu
zakoczenia procesu instalacji CPU.
-1-
B. Instalacja procesora AMD (moesz pomin ten etap, jeli Twoja pyta gwna posiada
zintegrowany procesor)
B-1 Podnie dwigni blokady gniazda procesora. Dopasuj Gniazdo procesora Dwignia
pierwszy pin procesora (oznaczony maym trjktem) z
oznaczeniem na gniedzie i delikatnie umie procesor w
gniedzie. Upewnij si e piny procesora dokadnie pasuj
do otworw.
pooenie.
Nie umieszczaj procesora w gniedzie na si. Nie ma moliwoci niepoprawnego woenia procesora. Jeli
zajdzie taka potrzeba, popraw dopasowanie procesora.
Uwaga! W adnym wypadku nie naley dotyka zczy gniazda procesora. W celu ochrony gniazda procesora,
zawsze naley zakada to zabezpieczenie jeli procesor nie jest zainstalowany.
Krok
2 Instalacja pamici
Krok
-2-
Krok
Polski
tylna blaszka
Krok
Krok
D o jednego zcza IDE mona podczy do dwch urzdze IDE. Przed instalacj sprawd ustawienie
zworek (master and slave) na urzdzeniu IDE.
Jeli zainstalowano wicej ni jeden dysk twardy, wejd w BIOS pyty gwnej i ustaw prawidow
sekwencj bootowania.
-3-
Krok
Uwaga: zcza pinowe front panel'u mog si rni w zalenoci od modelu. Przeczytaj instrukcj obsugi
pyty gwnej dla sprawdzenia aktualnego rozmieszenia pin'w
Krok
-4-
Kurulum sras, kasann trne ve kullanlan aygtlara gre deiiklik gsterebilir. Aadaki
kurulum talimatlar GIGABYTE'nin masast sistemleri iin geerli olup sadece bilgi amaldr.
Detayl anakart zellikleri iin kullanc el kitabna bakn.
Aygtlarn kurulumunu yapmadan nce, aygtlarnzn bilgisayarnzdaki girilerle uyumlu olup
olmadndan emin olun.
Aygtlarn kurulumunu yapmadan nce, aygtlar ve bilgisayarnz kapattnzdan emin
olun. Aygtlara ve sistem bileenlerine zarar gelmesini nlemek iin g kablosunu elektrik
fiinden karn.
Sarsnt ya da geveklik nedeni ile oluabilecek kaymalardan, kontrolsz yer deitirmelerinden
dolay meydana gelebilecek hasarlar nlemek iin bilgisayar sistemini salam bir yzeye
koyun.
1
Adm
A. Intel CPU Kurulumu (Anakartta yerleik bir CPU varsa bu adm atlayn)
A-1 CPU'nuzun teknik zelliklerini esas alan aadaki talimatlara baknz:
Tip A:
CPU soket kolunu kaldrn, metal tayc levha da kalakacaktr.
a. Koruyucu soket kapa CPU soketine taklysa, ilk nce onu karn.
Trke
b. Koruyucu yuva kapa metal yk plakasna taklysa, bu aama onu
karmayn. CPU'yu taktktan sonra kolu tekrar etkin hale getirirken
yuva kapa kendiliinden yk plakasndan frlayabilir.
Tip B:
A kolunu (" " iaretine en yakn olan) aaya doru soketten uzaklatrarak an. Ardndan B
kolunu (" " iaretine en yakn olan) aaya doru soketten uzaklatrn ve kaldrn. Yk plakasnn
kaldrlmasna olanak salamak iin A koluna hafife bastrn. Yk plakasn an.
A kolunu B kolunu
A-2 CPUyu baparmanzla ve iaret parmanzla tutun. aretli olan (gen) CPU pini CPU yuvasnn
kesindeki iareti ile yan yana gelecek ekilde hizalayn (ya da CPU dilileri ile yuva hizalama entiklerine
gre hizalayabilirsiniz) ve hafife bastrarak CPUyu yerine takn.
A-3 CPU doru olarak yerletirildikten sonra, metal levhay yerine yerletirin ve CPU kolunu iterek eski kilitli
konumuna getirin.
Tip B dzgn bir ekilde yerletirildiinde, yk plakasn dikkatlice yerletirin. Ardndan B kolunu tutma
sekmesinin altnda sabitleyin. Soket kapa kolu takarkenki sre srasnda yk plakasndan kabilir. Son
olarak A kolunu tutma sekmesinin altnda tutarak CPU kurulumunu tamamlayn.
CPU kurulumu hakknda ayrntl talimatlar iin, ltfen kullanc klavuzuna bakn.
-1-
B. AMD CPU Kurulumu (Anakartta yerleik bir CPU varsa bu adm atlayn)
B-1 CPU yuva kolunu tamamen kaldrn. lk CPU pini (ufak gen
iaretli) ile CPU yuvasndaki gen iareti ayn hizaya getirin CPU yuva Kolu
ve hafife bastrarak CPUyu yerine takn. CPU pinlerinin tam
olarak deliklere uyduundan emin olun.
2
Adm
Bellein Kurulumu
Bellek modlnn giri ynlerine dikkat edin. Bellek yuvalarnn iki ucundaki tutma
klipslerini iki yana an. Bellek modln yuvaya yerletirin. Soldaki resimde
gsterildii gibi, parmaklarnz bellein iki st ucuna yerletirin, bellein zerine
bastrarak bellek yuvasna dikey bir ekilde yerletirin. Bellek modl dzgn bir
ekilde yerletirildiinde yuvann iki ucundaki tutma klipsleri yuvasna oturacak.
3
Adm
-2-
4
Adm
Anakartn Kurulumu
Arka paneldeki I/O (Giri/k) balant noktalarna sahip orijinal plakay anakart
ile gelen G/ plakas ile deitirin. G/ plakasna denk gelecek ekilde anakart
kasann iine yerletirin. Anakarttaki montaj delikleri ile kasann zerindeki
montaj deliklerini uygun gelecek bir ekilde hizalayn. Anakart vidalarla yerine
skca oturtun.
G/ Plakas
5
Adm
Trke
Geniletme kart satn almadan nce, kartn boyutunun kasanza uygun
olup olmadn kontrol edin.
Genileme kartnn yerine tam olarak oturduundan emin olun.
PCI Express Ekran Kart
6
Adm
6-1 DVD-ROM ve CD-ROM gibi optik srclerinizi kurun. Kasann nndeki 5,25 src
yuvas kapan karn. Optik srcy 5,25 src yuvasna takn ve vidalar ile
skca tutturun.
Bir anakart IDE giriine iki adet IDE srcs balanabilir. Kurulumdan nce, IDE srclerinin zerindeki
jumper ayarlarn (master ve slave) kontrol edin.
Eer birden fazla sabit src kurulduysa, sistemdeki BIOS ayarlarna girerek sabit srclerin nykleme
srasn ayarlayn.
-3-
7
Adm
7-1 IDE/SATA konektrleri ve n panel ses, USB, IEEE 1394 balantlar, anakarttaki dahili konektrlere ve
balant noktalarna balayn.
7-2 n panel modln (g dmesi, yeniden balatma dmesi, hoparlrler, sabit disk faaliyet gstergesi
ve g gstergesi vs. kasann tipine gre deiiklik gsterebilir) kasadan anakarttaki n panel
balantsna (F_PANEL) takn.
Pim yeri A: Pim yeri B: MSG: Mesaj/G/Uyku LEDi
PWR: G LEDi
+MSG- +PW- +SPEAK- +MSG- +PW- +SPEAK-
PW: G Dmesi
2 20 SPEAK: Hoparlr
1 19 HD: Sabit Disk Faaliyet LEDi
RES: Yeniden Balatma Dmesi
+HD- -RES+ +HD- -RES+ -CI+ +PWR- CI: Kasa zinsiz Giri Engelleme
n Panel Balants NC
Balants
(Not) n panel balantsnn pim yerleri modele gre farkllk gsterebilir. Asl pim yerleri iin ana kartnzn
kullanma klavuzuna baknz.
8
Adm
-4-
Secvena de instalare poate diferi n funcie de tipul de carcas i de dispozitivele utilizate.
Instruciunile de instalare de mai jos se aplic pentru sistemele desktop GIGABYTE i sunt
numai pentru referin.
Consultai manualul de utilizare inclus pentru specificaiile detaliate ale plcii de baz.
nainte de instalarea dispozitivelor, asigurai-v c dispozitivele sunt conforme cu conectorii
de pe computer.
nainte de instalarea dispozitivelor, asigurai-v c dispozitivele i computerul sunt oprite.
Deconectai cordonul de alimentare de la borna de alimentare pentru prevenirea deteriorrii
dispozitivelor i a componentelor sistemului.
Aezai computerul pe o suprafa stabil pentru a preveni instalarea inadecvat cauzat
de oscilaii.
1
Pasul
A. Instalarea unui CPU Intel (ignorai acest pas dac placa de baz are un CPU ncorporat)
A-1 Consultai urmtoarele instruciuni pe bata specificaiilor procesorului:
Tip A:
Ridicai maneta soclului procesorului i placa greutii metalice va fi, de
asemenea, ridicat.
a. n cazul n care capacul prizei de protecie este fixat pe soclul
procesorului, mai nti scoatei-l.
b. n cazul n care capacul mufei de protecie este fixat pe placa de
sarcin metalic, nu l ndeprtai n acest moment. Acest capac se
poate desprinde brusc de pe placa de sarcin n timpul procesului de
recuplare a braului dup introducerea procesorului.
Tip B:
Push lever A (closest to the " " marking) down and away from the socket to release it. Then push
lever B (closest to the " " marking) down and away from the socket and lift it. Gently press lever A to
allow the load plate to rise. Open the load plate.
Romn
Prghia A Prghia B
A-2 Hold the CPU with your thumb and index fingers. Align the CPU pin one marking (triangle) with the pin one
corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and gently
insert the CPU into position.
A-3 O dat ce CPU-ul este introdus corect, aezai din nou plcua de metal i mpingei braul soclului de CPU
napoi n poziia blocat.
Dup ce unitatea tip B este fixat corect, nlocuii cu grij plcua de ncrcare. Apoi fixai mnerul B sub
dispozitivul de prindere. Capacul soclului se poate desprinde singur de pe plcua de ncrcare n timp ce
acionai mnerul. n final, fixai mnerul A sub dispozitivul de prindere pentru a finaliza instalarea CPU-ului.
-1-
B. Instalarea unui CPU AMD (ignorai acest pas dac placa de baz are un CPU ncorporat)
B-1 Ridicai complet braul soclului de CPU. Aliniai pinul unu al
CPU-ului (marcajul de triunghi mic) cu marcajul de triunghi Braul soclului de CPU
de pe soclul de CPU i introducei uor CPU-ul n soclu.
Asigurai-v c pinii CPU-ului se potrivesc perfect n orificii.
2
Pasul
Instalarea Memoriei
capete ale soclului de memorie. Aezai modulul de memorie pe soclu. Dup cum
este indicat n imaginea din stnga, aezai degetele pe marginea superioar a
memoriei, mpingei n jos memoria i introducei-o vertical n soclul de memorie.
Clamele de la ambele capete ale soclului cupleaz n poziie cnd modulul de
memorie este introdus fix.
3
Pasul
-2-
4
Pasul
Ecran I/O
5
Pasul
6
Pasul
Romn
bay-ului pentru unitate de 5,25 de pe partea din fa a carcasei. Montai unitatea
optic n bay-ul pentru unitate de 5,25 i fixai-o cu uruburi.
Un conector IDE de pe placa de baz poate conecta pn la dou dispozitive IDE. nainte de instalare,
verificai setrile elementelor de legtur (unitate master i slave) de pe dispozitivele IDE .
Dac este instalat mai mult de un hard disk, intrai n configurarea BIOS a sistemului pentru setarea
secvenei de ncrcare a hard disk-urilor.
-3-
7
Pasul
7-1 Conectai cablurile la conectorii i distribuitorii interni de pe placa de baz, inclusiv conectorii IDE/SATA,
audio de pe panoul frontal, USB, distribuitori IEEE 1394 etc.
7-2 Ataai modulul panoului frontal (difer n funcie de designul carcasei, cuprinznd indicatorul de alimentare,
indicatorul de activitate a hard disk-ului, difuzoarele, ntreruptorul de reiniializare, ntreruptorul de
alimentare etc.) de pe carcas pe distribuitorul panoului frontal (F_PANEL) (PANOU_F) de pe placa de
baz.
Semnificaia pinului A: Semnificaia pinului B: MSG: Message (Mesaj)/Power
(Pornire)/Sleep (Hibernare)
+MSG- +PW- +SPEAK- +MSG- +PW- +SPEAK- PWR: LED pornire
PW: ntreruptor de alimentare
2 20
SPEAK: Difuzor
1 19 HD: LED activitate hard disk
RES: ntreruptor de reiniializare
+HD- -RES+ +HD- -RES+ -CI+ +PWR-
Distribuitorul panoului frontal NC
CI: Comutator pentru mecanismul
de detectare a intruziunilor
(Not) Semnificaia pinilor de pe comutatorul din partea frontal poate s fie diferit n funcie de model. Consultai
manualul de utilizare al plcii de baz pentru semnificaia corect a pinilor.
8
Pasul
Conectarea Perifericelor
Partea din spate a carcasei
Surs de ntreruptor Dup ce paii de mai sus au fost completai, conectai
alimentare
Conector pentru dispozitivele periferice la computer, precum tastatura,
Port PS/2 pentru cablul de alimentare
tastatur mouse-ul, monitorul etc. Apoi conectai alimentarea,
Port PS/2 pentru
Port DVI-D mouse
pornii sistemul i instalai software-ul necesar.
Port HDMI Port D-Sub
Porturi eSATA Conector S/PDIF
Romn
-4-
. - GIGABYTE
.
.
, ,
.
, . ,
.
,
.
1
A. Intel (
)
A-1 , :
:
.
a.
, .
b.
, .
.
B:
(- " ") ,
. (- " ") ,
. , .
.
A B
A-2 . 1
() (
) .
A-3 ,
.
B , .
.
. ,
, .
.
-1-
B. AMD (
)
B-1 .
1 ( )
. ,
.
B-2 ,
CPU Socket 1
.
, .
. , , .
. ,
, .
C.
C-1 ,
. (
).
C-2
,
.
.
.
. ,
,
. ,
.
GIGABYTE .
, .
.
.
, ,
.
,
,
, .
-2-
I/O
I/O .
, I/O .
.
.
I/O
,
.
.
.
,
. , .
, .
PCI Express
6 IDE SATA
IDE IDE . ,
( ) IDE .
, BIOS,
.
-3-
7-1 , IDE/SATA
, USB, IEEE 1394 ...
7-2 (
, , , ,
..) (F_PANEL) .
: B: MSG: /. ./
sleep
+MSG- +PW- +SPEAK- +MSG- +PW- +SPEAK- PWR: . .
2 20 PW:
SPEAK:
1 19
HD:
+HD- -RES+ +HD- -RES+ -CI+ +PWR- RES:
NC CI:
() .
.
-,
PS/2
,
DVI-D PS/2
, , ,
.
HDMI D-Sub
.
eSATA S/PDIF
IEEE1394 USB
RJ-45 LAN
-4-
A teleptsi mveletek sorrendje eltrhet a hztpus s a felhasznlt eszkzk fggvnyben.
Az albbi teleptsi utastsok a GIGABYTE asztali rendszerekre rvnyesek, s csupn
hivatkozsi alapknt szolglnak.
Az alaplapra vonatkoz rszletesebb informcikrt olvassa el a csatolt felhasznli
kziknyvet.
Az eszkzk teleptse eltt gyzdjn meg arrl, hogy azok kompatibilisek a szmtgpen
lev csatlakozkkal.
Az eszkzk teleptse eltt kikapcsolja ki az eszkzket s a szmtgpet. Hzza ki a tpkbel
dugaszt a fali aljzatbl, hogy megvja az eszkzket s a rendszer sszetevit a meghibsodstl.
A szmtgpet stabil felletre lltsa, hogy elkerlje a rzkds miatti helytelen teleptst.
Lps
A. Intel CPU beszerelse (Hagyja ki ezt a lpst, ha az alaplapon beptett processzor van)
A-1 A CPU mszaki adatai alapjn tekintse meg az albbi utastsokat:
A tpus:
Emelje fel a CPU-foglalat rgzt karjt, s vele egytt felemelkedik a
fm tartlemez.
a. Ha a CPU-foglalon vdlap tallhat, tvoltsa el.
b. Ha a foglalat vdbortsa a fm tartlemezhez van rgztve, mg
ne tvoltsa el. A foglalat fedele magtl lepattanhat a tartlemezrl,
amikor a kart rgzti, miutn behelyezte a CPU-t.
B tpus:
Az "A" jel kart (a " " jells kzelben) nyomja lefel s a foglalattal ellenttes irnyba a kioldshoz.
A "B" jel kart (a " " jells kzelben) pedig nyomja lefel s a foglalattal ellenttes irnyba a
felemelshez. vatosan nyomja le az "A" jel kart, hogy felemelkedhessen a tartlemez. Nyissa fel
a tartlemezt.
Az "A" jel kart Az "B" jel kart
A-2 Hvelykujjval s mutatujjval tartsa a CPU-t. Illessze egymshoz a processzor els t jelzst (hromszg)
a processzor foglalat els t sarkval (vagy illessze ssze a processzor bevgsait a foglalat sszeilleszt
kulcsaival), majd vatosan helyezze a processzort a foglalatba.
A-3 A processzor behelyezse utn helyezze vissza a tartlemezt, majd nyomja vissza a processzor emelkarjt
zr llsba.
Amint megfelelen beszerelte az B tpus, vatosan helyezze vissza a tartlemezt. Ezutn rgztse a "B"
rgztkart hajtsa a tartfl al. A foglalat fedele lepattanhat a tartlemezrl, amikor a kart rgzti. Vgl
rgztse az "A" rgztkart a tartfl al a CPU beszerelsnek befejezshez.
Magyar
-1-
B. AMD CPU beszerelse (Hagyja ki ezt a lpst, ha az alaplapon beptett processzor van)
B-1 Emelje meg teljesen a processzor foglalatnak rgzt
karjt. Illessze egymshoz a processzor els tjt (kis Processzor foglalat rgzt karja
hromszg jelzs) a processzor foglalaton lev hromszg
jelzssel, majd vatosan helyezze a processzort a foglalatba.
Gyzdjn meg arrl, hogy a processzor ti tkletesen
illeszkednek a nylsokba.
B-2 A processzornak foglalatba helyezse utn nyomja r az egyik CPU foglalat Els t
ujjt a processzor kzepre, engedje le a foglalat rgzt
karjt, majd akassza be teljesen rgztett llsba.
Ne erltesse a processzort, amikor a foglalatba helyezi. A processzor csak egyflekppen helyezhet be a
foglalatba. Ha a processzor irnytsa nem megfelel, lltson rajta.
NE rintse meg a foglalat rintkezit! A CPU-foglalat vdbortst mindig helyezze vissza, ha a CPU-t
kiveszi a foglalatbl.
C. Processzorht beszerelse
C-1 A processzorht beszerelse eltt a processzor felletre kenjen
egy vkony rteg hnyel pasztt. Ezutn szerelje be a htt
(lsd a processzorht beszerelsi kziknyvt).
C-2 Csatlakoztassa a processzorht tpkbelt az alaplapon
lev CPU_FAN csatlakozhoz gy, hogy a ht megfelelen
mkdhessen, megakadlyozva a processzor tlmelegedst.
Lps
2 Memria Beszerelse
Lps
3 A Hz Elksztse a s Tp Beszerelse
-2-
Lps
4 Az Alaplap Beszerelse
Lps
5 Bvtkrtya Beszerelse
Keresse meg azt a bvt foglalatot, amelyet a krtynak tartottak fenn, majd
tvoltsa el a foglalat vdlapjt a hz htuljrl. Helyezze be a bvtkrtyt
a foglalatba. Rgztse a bvtkrtya fmtartjt a szmtgphz htlapjhoz
egy csavarral.
Bvtkrtya beszerzse eltt ellenrizze a krtya hosszsgt, hogy
befr-e a szmtgphzba.
PCI Express videokrtya Gyzdjn meg arrl, hogy a bvtkrtyt teljesen belenyomta a
foglalatba.
Lps
Merevlemez beszerelse
Az alaplap egyetlen IDE csatlakozjhoz maximum kt IDE eszkz csatlakoztathat. A beszerels eltt
ellenrizze az IDE eszkzk jumper-belltst (Master s Slave).
Ha tbb merevlemezt szerel be, lpjen a rendszer BIOS-belltsokba, hogy belltsa az indtsi sorrendet.
Magyar
-3-
Lps
Lps
8 A tartozkok csatlakoztatsa
Kszlkhz htlapja
-4-
. GIGABYTE
.
.
,
.
,
.
.
.
A.
Intel (
CPU)
A-1 CPU :
:
CPU
.
a.
CPU, .
b.
, .
CPU.
B:
( " ")
. , ( " ")
.
. .
A B
A-2 .
() (
)
.
A-3 ,
.
( B),
. , .
. ,
(CPU).
CPU, .
-1-
B.
AMD (
CPU)
B-1 .
(
)
.
.
B-2 ,
CPU Socket Pin 1
,
.
.
. , .
. ,
.
C.
C-1 ,
. , (
).
C-2
CPU_FAN
.
.
.
. ,
,
.
.
GIGABYTE ,
.
.
.
,
.
,
.
-2-
I/O
I/O .
I/O.
. .
. ,
.
.
,
.
PCI Express .
6 IDE SATA
IDE IDE.
, (master slave)
IDE.
,
BIOS .
-3-
7-1 ,
IDE/SATA , USB, IEEE 1394 .
7-2 (
, , ,
, , )
(F_PANEL).
: : MSG: //
LED
+MSG- +PW- +SPEAK- +MSG- +PW- +SPEAK- PWR: LED
2 20 PW:
SPEAK:
1 19
HD: LED
+HD- -RES+ +HD- -RES+ -CI+ +PWR-
NC RES:
CI:
() .
.
,
, , ,
PS/2
DVI-D PS/2 . , ,
HDMI D-Sub
eSATA S/PDIF
.
IEEE1394 USB
RJ-45
-4-
Poad instalace se me liit v zvislosti na typu skn a pouitch zazen. Ne uveden
pokyny pro instalaci se vztahuj na stoln potae GIGABYTE a jsou pouze orientan.
Podrobn specifikace zkladn desky viz dodan uivatelsk pruka.
Ped instalac zazen zkontrolujte, zda jsou kompatibiln s konektory na vaem potai.
Ped instalac vypnte zazen a pota. Odpojte napjec kabel z elektrick zsuvky, aby
se zabrnilo pokozen zazen a potaovch komponent.
Umstte pota na stabiln msto, aby se zabrnilo nevhodn instalaci zpsoben otesy.
Krok
etina
etina
A. Instalace procesoru Intel (peskote tento krok, pokud je zkladn deska vybavena
integrovanm procesorem)
A-1 Dodrujte nsledujc pokyny, kter jsou zaloeny naspecifikacch vaeho procesoru:
Typ A:
Zvednte pku patice procesoru; souasn se zvedne kovov
zatovac destika.
a. Je-li napatici procesoru pipevnn ochrann kryt, sejmte jej jako
prvn.
b. Pokud je ochrann kryt patice pipevnn ke kovov zavdc desce, v
tto chvli jej nesnmejte. Bhem procesu zajiovn pky po vloen
procesoru me dojt k odskoen krytu patice ze zavdc desky.
Typ B:
Uvolnte pku A (nejble znace " ") stisknutm dol od patice. Potom uvolnte pku B (nejble
znace " ") stisknutm dol od patice a zvednte ji. Opatrnm stisknutm pky A nechte zvednout
zavdc desku. Otevete zavdc desku.
Pku A Pku B
A-2 Uchopte procesor palcem a ukazovkem. Zorientujte znaku kolku 1 procesoru (trojhelnk) s rohem kolku
1 patice procesoru (nebo mete zorientovat drky na procesoru kli pro zarovnn patice) a opatrn
zasute procesor na msto.
A-3 Po sprvnm usazen procesoru nasate zavdc desku a zatlate pku patice procesoru do zamknut polohy.
Kdy je typ B sprvn usazen, opatrn nasate zavdc desku. Potom zajistte pku B pod jej zajiovac
jazek. Bhem procesu zajiovn pky me dojt k odskoen krytu patice ze zavdc desky. Nakonec
dokonete instalaci procesoru zajitnm pky A pod jej zajiovac jazek.
-1-
B. Instalace procesoru AMD (peskote tento krok, pokud je zkladn deska vybavena
integrovanm procesorem)
B-1 Zcela zvednte pku patice procesoru. Zorientujte kolk Pka patice procesoru
1 procesoru (znaka malho trojhelnku) se znakou
trojhelnku na patici procesoru a opatrn zasute procesor
do patice. Kolky procesoru se mus zcela zasunout do
pslunch otvor.
Nezatlaujte procesor do patice silou. Nesprvn zorientovan procesor nelze usadit. V takovm ppad
zmte orientaci procesoru.
NEDOTKEJTE SE kontakt patice. Pokud nen nainstalovn procesor, vdy nasate ochrann kryt
patice procesoru, aby se zabrnilo jejmu pokozen.
2 Instalace Pamti
Krok
Pouijeme-li jako pklad stoln pota GIGABYTE, ped instalac zdroje napjen
nejdve sejmte ob strany a vko skn. Umstte zdroj napjen na sprvn
msto ve skni a zajistte roubky. Instalace a umstn zdroje napjen se me
liit v zvislosti na typu pouit skn.
Pro zajitn dostatenho napjen potae doporuujeme pout
kvalitn zdroj napjen. Zdroj napjen nedostaten kapacity me
zpsobit nestabilitu systmu nebo znemonit jeho sputn.
-2-
Krok
Odmontujte pvodn tt I/O ze zadn strany skn a nahrate jej ttem I/O
zkladn desky. Umstte zkladn desku do skn vloenm do pslunho
ttu I/O. Zarovnejte otvory pro rouby na zkladn desce s odpovdajcmi
montnmi otvory ve skni. Zajistte zkladn desku na mst rouby.
etina
etina
Krytka I/O
Krok
Krok
K jednomu konektoru IDE na zkladn desce lze pipojit a dv zazen IDE. Ped instalac zkontrolujte
nastaven propojek (nadazen a podazen) na zazench IDE.
Je-li nainstalovn vce ne jeden pevn disk, pejdte do sti BIOS SS Setup (Nastaven systmu BIOS)
a nastavte zavdc sekvenci pevnch disk.
-3-
Krok
7-1 Pipojte kabely k internm konektorm a paticm na zkladn desce vetn konektor IDE/SATA,
konektor zvuku na pednm panelu, konektor USB, patic IEEE 1394 atd.
7-2 Pipevnte modul pednho panelu (li se v zvislosti na designu skn, skld se z indiktoru napjen,
indiktoru innosti pevnho disku, reproduktor, resetovacho spnae, vypnae napjen atd.) ze skn
k patici pednho panelu (F_PANEL) na zkladn desce.
etina
(Poznmka) Piazen vvod pro hlaviku pednho panelu se me liit podle modelu.
Aktuln piazen vvod viz uivatelsk pruka k zkladn desce.
Krok
8 Pipojen Perifri
Zadn panel skn
-4-
Redosled koraka prilikom instalacije moe se razlikovati u zavisnosti od sluaja i ureaja koji
se koriste. Instrukcije za instalaciju koje ete nai ispod vae za desktop sisteme kompanije
GIGABYTE i slue samo kao referentni materijal.
Pogledajte Uputstvo za korienje koje ste dobili za detaljne specifikacije vezane za matinu
plou.
Pre instaliranja ureaja, proverite da su vai ureaji kompatibilni sa konektorima na vaem
kompjuteru.
Pre instaliranja ureaja obavezno iskljuite svoje ureaje i svoj kompjuter. Izvucite kabl za
struju iz tekera da bi spreili oteenje ureaja i komponenti sistema.
Postavite kompjuterski sistem na stabilnu povrinu da bi spreili nepravilnu instalaciju usled
klimanja.
Korak
A. Instaliranje Intelovog procesora (preskoite ovaj korak ukoliko matina ploa ima ugraen procesor)
A-1 Pratite sledea uputstva u zavisnosti od specifikacija vaeg procesora:
Tip A:
Podignite polugu podnoja procesora i metalna preklopna ploica e
Srpski
se takoe podignuti.
a. Ako je zatitni pokriva podnoja privren na podnoju procesora,
prvo ga uklonite.
b. Ako je zatitni poklopac podnoja privren na metalnoj noseoj
ploi, ne uklanjajte ga u ovoj fazi. Poklopac podnoja se moe
automatski odvojiti od nosee ploe tokom natezanja poluge nakon
postavljanja procesora.
Tip B:
Gurnite polugu A (najbliu oznaci " ") nanie i dalje od podnoja da je otpustite. Gurnite polugu B
(najbliu oznaci " ") nanie i dalje od podnoja i podignite je. Paljivo pritisnite polugu A da dozvolite
ploici za pritiskanje da se podigne. Otvorite ploicu za pritiskanje.
Polugu A Polugu B
A-2 Drite procesor palcem i kaiprstom. Poravnajte oznaku prve noice procesora (trougao) sa uglom za iodu
jedan na podnoju procesora (ili moete da poravnate lebove procesora sa oznakama za poravnavanje
podnoja) i paljivo ubacite procesor na mesto.
A-3 Jednom kada je procesor ispravno postavljen, spustite ploicu za optereivanje i gurnite ruicu za podnoje
procesora natrag u poloaj za blokiranje.
Jednom kada je tip B ispravno ubaen, paljivo postavite ploicu za pritiskanje. Potom zategnite i zakljuajte
polugu B ispod njenog zateznog jezika. Poklopac podnoja moe da se otkai sa ploice za pritiskanje
tokom procesa zatezanja polugice. Na kraju, zategnite i zakljuajte polugu A ispod njenog zateznog jezika
da zavrite instaliranje procesora.
-1-
B. Instaliranje AMD procesora (preskoite ovaj korak ukoliko matina ploa ima ugraen
procesor)
B-1 Potpuno podignite ruicu za zakljuavanje procesora.
Poravnajte noicu jedan procesora (oznaenu malim Ruica za aicu procesora
trouglom) sa trouglastom oznakom na podnoju procesora
i paljivo ubacite procesor u podnoje. Proverite da noice
procesora savreno upadaju u svoje rupice.
2 Instaliranje memorije
Obratite panju na to kako je okrenut memorijski modul. Rairite klipove koji dre
memoriju sa obe strane podnoja za memoriju. Smestite memorijski modul u
podnoje. Kako je prikazano na slici levo, stavite prste na vrh memorije, pritisnite
memoriju i ubacite je vertikalno u podnoje za memoriju. Klipovi sa obe strane
podnoja e se vratiti na mesto kada je memorijski modul ispravno ubaen.
Korak
-2-
Korak
Uklonite originalni I/O tit sa poleine kuita i zamenite ga I/O titom matine
ploe. Stavite matinu plou u kuite smetajui je na svoj I/O tit. Poravnajte
rupice za montiranje na matinoj ploi sa odgovarajuim rupicama za montiranje
na kuitu. Privrstite matinu plou na mesto rafovima.
I/O tit
Korak
Pronaite odreeni port (slot) koji podrava vau karticu i uklonite poklopac porta
(slota) sa zadnje strane kuita. Potom ubacite karticu u port (slot). Privrstite
Srpski
spoj ekspanzione kartice za poleinu kuita rafom.
Korak
Jedan IDE konektor na matinoj ploi moe da povee do dva IDE ureaja. Pre instalacije, proverite kako
su podeeni damperi (master i slejv) na vaim IDE ureajima.
Ukoliko ste instalirali vie od jednog hard diska, uite u BIOS podeavanja da bi odredili redosled
podizanja hard diskova.
-3-
Korak
Korak
Poleina kuita
-4-
Redoslijed pri instalaciji moe varirati ovisno o vrsti kuita i koritenim ureajima. Donje
upute za ugradnju vrijede za GIGABYTE stolna raunala i slue samo kao referenca.
Prouite korisniki prirunik radi detaljnih podataka o matinoj ploi.
Prije ugradnje ureaja, provjerite jesu li sukladni prikljucima na vaem raunalu.
Prije ugradnje ureaja, pobrinite se da budu iskljueni i ureaji i raunalo. Iskopajte kabel
elektrinog napajanja iz zidne utinice, kako biste sprijeili oteenje ureaja i komponenti
sustava.
Raunalni sustav stavite na ravnu i stabilnu povrinu, kako ne bi dolo do greaka u
instalaciji uslijed trenje.
1
Korak
A. Ugradnja Intel procesora (preskoite ovaj korak ako je procesor ugraen na matinoj ploi)
A-1 Pogledajte sljedee upute temeljem sljedeih podataka o procesoru:
Vrsta A:
Podignite ruicu podnoja procesora i metalna ploica za ulaganje e
se takoer podignuti.
a. Ako je zatitni poklopac podnoja privren za podnoje procesora,
prvo skinite njega.
b. Ako je zatitni poklopac podnoja privren na metalnu plou
za umetanje, nemojte je jo skinuti. Poklopac utinice e moda
sam automatski iskoiti s ploe za stavljanje za vrijeme ponovnog
aktiviranja ruice nakon umetanja procesora.
Vrsta B:
Gurnite ruicu A (najblia oznaci " ") dolje i dalje od podnoja kako biste ga oslobodili. Gurnite ruicu
B (najblia oznaci " ") dolje i dalje od podnoja i dignite ga. Blago pritisnite ruicu A kako biste omoguili
dizanje ploice za umetanje. Otvorite ploicu za umetanje.
Hrvatski
Ruicu A Ruicu B
A-2 Uhvatite procesor izmeu kaiprsta i palca. Poravnajte (trokutastu) oznaku kontakta broj jedan s kutom
kontakta jedan na podnoju (ili moete poravnati usjeke procesora s kljuevima poravnavanja) i blago
gurnite procesor na svoje mjesto.
A-3 Kad procesor ispravno ugraen, vratite ugradbenu plou i gurnite ruicu podnoja procesora u blokirani poloaj.
Kad ste propisno umetnuli vrsta B, paljivo vratite ploicu za umetanje. Zatim privrstite ruicu B ispod
jezika za osiguranje. Poklopac podnoja moda e odskoiti s ploice za umetanje za vrijeme postupka
zaglavljivanje ruice. Na kraju, privrstite ruicu A ispod svog jezika za fiksiranje i zavrite ugradnju
procesora.
-1-
B. Ugradnja AMD procesora (preskoite ovaj korak ako je procesor ugraen na matinoj ploi)
B- 1 Podignite do kraja ruicu podnoja procesora. Poravnajte
kontakt broj 1 na procesoru s trokutastom oznakom na CPU podnoje Ruica
podnoju procesora. Provjerite ulaze li kontakti procesora
besprijekorno ulaze u kontakte podnoja.
Korak
2 Instalacija memorije
Korak
-2-
4
Korak
I/O titnik
Korak
Korak
Hrvatski
6-1 Instalirajte optike ureaje kao to su DVD-ROM i CD-ROM.
Izvadite leite za 5,25" pogon s prednje strane kuita. Ugradite optiki pogon u
leite ureaja 5,25" i stegnite ga vijcima.
Jedan prikljuak na matinoj ploi moe se spojiti na dva IDE ureaja. Prije instalacije, provjerite
postavke premosnika (glavni i sporedni) na vaim IDE ureajima.
Ako instalirate vie od jednog hard diska, uite u BIOS Setup (BIOS postavke) i podesite redoslijed
pokretanja raunala.
-3-
7
Korak
7-1 Spojite kablove na unutarnje prikljuke i zaglavlja na matinoj ploi, ukljuujui IDE/SATA prikljuke i
audio prednje ploe, USB, IEEE 1394 zaglavlja, itd.
7-2 Spojite modul prednje ploe (varira ovisno o dizajnu kuita, a sastoji se od pokazivaa struje,
pokazivaa aktivnosti hard diska, zvunika, sklopke za resetiranje, sklopke za ukljuivanje, itd.) s
kuita na zaglavlje prednje ploe (F_PANEL) na matinoj ploi.
Pin dodjele A Pin dodjele B: MSG: Poruka/ LED u pogonu / LED u
mirovanju
+MSG- +PW- +SPEAK- +MSG- +PW- +SPEAK- PWR: LED u pogonu
2 20 PW: Sklopka za ukljuivanje
SPEAK: Zvunik
1 19
HD: LED aktivnosti tvrdog diska
+HD- -RES+ +HD- -RES+ -CI+ +PWR- RES: Sklopka za reset
Zaglavlje prednje ploe NC CI: Chassis Intrusion Header
Zaglavlje otvaranja kuita
(Napomena) Pin dodjele za zaglavlje prednje ploe mogu se razlikovati ovisno o modelu. Prouite korisnike
upute matine ploe za aktualne pin dodjele.
Korak
-4-
7
7-1 , ,IDE/SATA- USB, IEEE ,
,1394.
7-2 ) , , , ,
) ,(Reset ,'( ) (F_PANEL .
B: A:
:MSG LED//
:PWR LED +MSG- +PW- +SPEAK- +MSG- +PW- +SPEAK-
:PW 20 2
:SPEAK 19 1
:HD LED
:RES +HD- -RES+ -CI+ +PWR- +HD- -RES+
NC
:CI
)( . .
,
, , ,' , . PS/2
, ,
DVI-D PS/2
.
HDMI D-sub
eSATA S/PDIF
RJ-45 LAN
-4-
4
) (I/O shield ,
) (I/O shield .
) .(I/O shield
.
.
)(I/O shield
5
.
.
.
,
.
.
PCI Express
IDESATA-
6
6-1 DVD-ROM.CD-ROM-
"5,25- .
"5,25- .
6-2 IDE.SATA-
, .
IDE- .IDE ,
) master (slave- ) (Jumper .IDE-
, BIOS- .
-3-
. ) AMD (
' 1- . '
) ( ,
.
.
' 2- , ,
.
1
. . ,
.
. , .
.
' 1- ,
. )
(.
' 2- CPU_FAN-
.
.
2
.
. . ,
, ,
.
.
3
GIGABYTE ,
. ,
. .
,
.
.
-2-
.
GIGABYTE .
, .
, .
, .
.
.
. ) Intel (
' 1- :
:A
.
a. , .
b. ,
.
.
:B
'( . B ) A '
) ' '( , . A
. .
B A
' 3- , .
B , . B
. . A
.
, .
-1-