2013 SECTION IL, PART B 8-626
SPECIFICATION FOR WELDED NICKEL AND
NICKEL-COBALT ALLOY TUBE
C8 SB-626
(Identical with ASTM Specification 8626-06 except that E 527 was removed from References, and
certification has been made mandatory.)
929s2-626
2013 SECTION HL, PART B
SPECIFICATION FOR WELDED NICKEL AND NICKEL-
COBALT ALLOY TUBE
SB-626
(Cetical with ASTM Specification B 626-06 except that E $27 was removed fom References, and certification hasbeen made mandatory)
Scope
1.1 This specification covers welded tubes made from
the nickel and nickel cobalt alloys (UNS N1O001, UNS
1N10249, UNS N10665, UNS NI2160, UNS N10629, UNS
'N10624, UNS N10675, UNS N10276, UNS NO6SS, UNS
'N06007, UNS NO6975, UNS NO8320, UNS NO698s,
‘UNS N06002, UNS NO6022, UNS NOG030, UNS NO6O3S,
'UNS NO60SE, UNS NOGOS9, UNS NO6200, UNS 06210,
UNS NOSOS1. UNS R30SS6, UNS NO6230, UNS NO66SE,
and UNS R20033) listed in Table 1 intended for hea
exchanger and condense tubes an tbesfor general coro
sive service for heat-resistng applications
1.2 This speciation covers tube {to 34 in, @2 10
8859 mm) in outside diameter and 0.015 to 0.148 in. (O41
to 37 mi) inclusive, in wall thickness
3. The values stated in inch-pound units are to be
regarded as the standard. The values given in parentheses
are for information only.
14 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsiblity of the user ofthis standard to become fail
iar with all hazards including those identified in the appro:
priate Material Safety Data Sheet (MSDS) for this product/
‘material as provided by the manufacturer, to establish
‘appropriate safety and health practices, and determine the
applicability of regulatory limitations prior to use.
2. Referenced Documents
21 ASTM Standards:
B 751 Specification for General Requirements for Nickel
and Nickel Alloy Welded Tube
General Requirements
3.1. Material furnished in accordance with this specifi-
cation shall conform to the applicable requirements of the
930
ccurrent edition of Specification B 751 unless otherwise
provided herein,
4. Classification
4.1 Five classes of tube are covered as follows:
4.1.1 Class IA — Welded, sized, solution annealed,
‘and nondestructively tested in accordance with 4.2.1
4.1.2 Class 1B — Welded, sized, and solution
annealed,
4.13 Class UA — Welded, cold worked, solution
annealed, and nondestructively tested in accordance with
42.1
4.14 Class IIB — Welded, cold worked, and solution
annealed.
4.1.5 Class II — Welded, cold worked, solution
annealed, and nondestructively tested in accordance with
4.222,
42 Nondestructive Tests
4.21 Class IA and Class IA Tubes — Bach finished
‘ube shall be subjected tothe hydrostatic test, the pneumatic
test, of the eddy current test at the manufacturer's option
42.2 Class HII Tubes — Bach finished tube shall be
subjected to the pneumatic test and the eddy current test.
‘Tubes larger than 1's in, (38.1 mm) in outside diameter
may be subjected to the hydrostatic test in licu of the
pneumatic test at the manufacturer's option,
5. Ordering Information
51 It is the responsibility of the purchaser to specify
all requirements that are necessary for material ordered
under this specification, Examples of such requirements
include, but are not limited to the following:
S.L1 Alloy (Table 1),sp-s26
2013 SECTION Il, PART B
ww 500 wu oot | wu | sxe | sro | ost ove
0 “soo > | “oe we | om sroo| coo foe [Sef “es “S29 “$09 “Tey ww or freer} Pod spueses
set |u| au foro] oro } oro } oro Jooz| or | ove | sto vee
Ceq eq “sod -org “sorq “tod “ot s+ aro | woo | +++ |SS5q “oy “se “Sodeeod xpucus: lowed] “ota cxe-oer | ossoey
sou so | ot wor | oe
«00 | woo DIkeee ot | “sq “vey oveoer| "=o sod spews
‘any coo | v0 % ox | “eo sspureass foo “8d ovz-ose
oe qre-o'} zo loo |] st] og oo | comer-stjoxt-ost eon -v'8q spuewas | oca90N
m= wea] xe | seu | seu oe ae
wrest] feoo [roo [os | “od og oy sto stfore-oar bres “org sounwa | sesoon
+ [Sore “org coo evo Po | oy <= | ot | sor 2 | smmues puree -o'e9 ozs-our | susson
Seieesi| | coo | wo "Fy ed ot | “sod oxfore-oat fex-se] “O14 sopuwus | zo090n
oN
oa ru | oo oy ou | on
209 00 | soo Og aa ave | tod oo | auc | “om “ory spueuss | sso90n
of oe sto | ocao | “ced “os'd “oon ove | osod oFg xewonz | ~ovd=szeq sseueus | scooow
seu | | rau em] 22
vo | e+ | 200 | zoo |'seq "sq 2} coo er so] ove | “Fey “004 seumum | 220900
evo [ooo |'seq “of $4 ove | owogeroe] oor | “osy “Fr arueuss | eeotn
Soe
a vu mu yeu | seu ou on
00 08 tq — | stoo|ocoo] "seq “co aoe | “eo reuse | eeepeod wana | even
* wo |rewo of oro | ted ~~ | oes | “014 “09 sovmws | vesorn
“ vs) aoe [ae | = o-r9| . wo | 200 £3 <0 | 10 ooor | “gagetr9] snueue | sesorn
ae | seu | rw veu_[ seu wou | seu rd wu | sew eee
“og ed 2! ° + | “Seq ‘oza| ovo | ocoo 04 ovo | “tod oe oc-or | ouAreoy] uw ose | seoorw
wm oo ove |
evo | woo. of oe ore | “zoq + | ewoe | “09g " on} apuewe | soot
ro | wu | ee sm eee |
“Lode fees 0% osar | "e9q “63 spucuas | tooo
ma jepe|s| a |2|wlar]~ | a psa a f[ oo fewsl o fm | 2 fw fo] w
oh ” a
es
uy oH
‘SLNAW3INOSY IWOIW3HD
Ta1svL,
9312013 SECTION 1, PART B
626
‘seo “Sa] o> | 200 | 200 ove | sto cance | S59] Sote| oxe-ooe | exces
meaner
Site) “rr] o> [oroe |ezoo | e0 | Seon] cams | 59] S082] oze-00 | eso00n
-20%] ors] osu] “++ Jot | sto 9] co] “ord oro] eo) xewer | “oer] Cove] sameq | esovon
ea | on | a [aw vfa [2 [way [a fewsfewa] x fon] oo pesto tm |= )or |) w
ty ” caw
aa aoe
(@ANOD) SLNAWSUINDSY TWOIWSHD
TaTavL
9322013 SECTION Il, PART B
54.2 Class (see 4),
5.1.3 Quantity (feet or number of lengths),
5.1.4 Size (outside diameter and average wall
thickness),
5.1.5 Length (cut or random),
5.1.6 Certification —Certification and a report of test
results are required,
5.1.7 Purchaser Inspection — State which tests or
inspeotions are to be witnessed,
5.18 Ends — Plain ends cut and deburred will be
furnished, unless otherwise specified, and
5.1.9 Samples for Product (Check) Analysis — State
whether samples shall be furnished.
6. Materials and Manufacture
6.1 The tubes shall be made from flat-olled alloy by
‘an automatic welding process with no addition of filler
6.2. Subsequent to welding and prior to final heat treat-
ment, Class IT and Class Ill tubes shall be cold worked
cither in both weld and base metal or in weld metal only.
‘The method and amount of cold working may be specified
by the purchaser. When cold drawn, the purchaser may
specify the minimum amount of reduction in cross-sec-
tional area or wall thickness, or both.
6.3 All tubes shall be furnished in the solution annealed
and descaled condition, When atmosphere control is used,
descaling is not necessary.
7. Chemical Composition
TAL The material shall conform to the requirements for
chemical composition prescribed in Table 1. One test is
required for each lot as defined in Specification B 751
72. Ifa product (check) analysis is performed by the
purchaser, the material shall conform to the requirements
specified in Table 1 subject to permissible variations speci-
fied in Specification B 751
Mechanical Properties and Other Requirements
8.1 Mechanical Properties — The material shall con-
form to the mechanical properties prescribed in Table 2.
(One testis required for each lot as defined in Specification
BSL
8.2 Flaitening Test Requirements:
8.2.1 Evidence of laminated or unsound material
‘or of incomplete weld that is revealed during the entire
flattening test shall be cause for rejection.
933
8.626
TABLE 2
MECHANICAL PROPERTIES
Tensile Vield Strength Elongation in
Svenath, (02 Offset) 2 in. G08
rai ksi mi kat mm) or 40
Alloy (Opa) (MiPay__{AY, min, %
ime
UNS Na0001 200 (690) 45 (310) 40
UNS 10665 120 (760) 5150) 40
‘Uns ni0675 110 (760) $150) 40
UNS Wi0629 10760) 51.650) 40
UNS 10624 104 (720) 466320) 40
Ni-Mo-cr-Fe
‘UNS toz42 208725) 450310) 40
Low ¢ Ni-Cr-Mo
UNS N20276 100 (690) a1 (203) 40
UNS Nowoze 00 (90) 45510) 45
UNS No6035 5 ($86) 35(241) 30
UNS Nosass 100690) 80(278) 40
h-cr-FeMo-cu
UNS No6o07 g0te2n) asian) 35
UNS No6975 5586) 520221) 40
uns Noeses 90t623) 35 (261) a5
UNS 06030 50586) 35241) 30
NEFe-CrMa
UNS N08320 Tsis1) 29099) 38
NiceMo-re
UNS Noso02 100 1690) 40276) 38
Ni-Fe-cr-co
UNS R30556 200 (690) 456510) 40
NiCr MEMO
UNS Nose30 (6) «110(760) 45310) 40.
Low G-N-Cr-M
UNS No6o5e ano (760 52360) 40
UNS No6o59 00 (690) 45.310) 45
Low ¢-ni-cr-e-0u
‘UNS Nosz00 100 (690) 450310045
low-carbon Ni-Fe-CrMo-Cu
‘UNS 106032, 940450) 4027 40
Low C-NisCr Mos
UNS Noses 200 (690) 45310745
nico-crsi
UNS Nizi60 900620) 35040) 40
low Carbon Cr-eFe-N
‘UNS 20033 109750) $8380) «0
Lowe NiMo-CreTa
UNS Noseza 300 690) 45(310) 45
ores:
(A) Deters tothe dameter ofthe tension specimen.
(B) Soliton annealed ata minim temperature of 2200°F(1204" C)
fellowed by a water querch or rapidly cooled by oter means.
8.2.2 Surface imperfections in the test specimens
before flattening, but revealed during the flatening test,
shall be judged in accordance withthe finish requirements
8.2.3. Superficial ruptures resulting from surface
imperfections shall not be cause for rejection,
8.24. One testis required for each lot as defined in
‘Specification B 751.sn-626
83 Flange Test Requirements:
8.3.1. Flange test specimens shall show no cracking
‘or flaws, Superficial ruptures resulting from surface imper-
fections shall not be cause for rejection
8.3.2. For tube less than 0.093 in. (2.36 mm) in inside
diameter and tube having a wall thickness equal to of
greater than the inside diameter, the flange test shall not
be required.
8.33. One testis required for each lot as defined in
Specification B 751
84 Hydrostatic Test — When tested by the manufac-
turer, each tube shall be subjected to the hydrostatic test
per Specification B 751
88 Pnewmatic Test —When tested by the manufacturer,
each tube shall be subjected to the pneumatic test per
Specification B 751.
8.6 Eddy Current Test — When tested by the manufac-
turer, each tube shall be subjected to an electromagnetic
(eddy current) test per Specification B 751
934
2013 SECTION 1, PART B
Certification
9.1 A manufacturer's certification shall be furnished
to the purchaser stating that che material has been manufac-
tured, ested, and inspected in accordance with this specifi-
cation, and that the test results on representative samples
‘meet specification requirements, A report ofthe test results
shall be furnished,
10, Keywords
10.1 UNS N10001; UNS N10242; UNS N10665; UNS
1N12160; UNS N10629; UNS N10624; UNS N10675; UNS
1N10276; UNS N06455; UNS NO6007; UNS NO6975; UNS
08320; UNS N06985; UNS N06002; UNS NO6022;
UNS NO6030; UNS NO603S; UNS NO6058; UNS NO6059:,
‘UNS NO6200; UNS N062i 08031; UNS N06230;
UNS N06686; UNS R30556; UNS R20033; welded tube