ly asz0 - 14
TABLE 9 Charpy V-Notch Test Acceptance Criteria for Various Sub-Size Specimons
FalSze 10by Tom —%Su0,10by7Smm See WyET am
80. 0b Sm
Te Ske, 10 oy 33mm Seo, THRE HA
bt bh br UL ‘Rr ul br wr Ret uw bt a
oe ise) 30 vet) 2 wy = 7 3 i18) 10 ia)
35 (23) 2 5] 2 iat) 18 4) 2 te ° 2
20 ist) 2 0) 2 cal 5 (20) 10 ta) 3 i
3 (4) 19 feo) 7 23) 2 16) 3 ina) 6 iB
20 fr 15 feo] 3 ta) 10 fn) 7 9) 8 a
6 22 2 fe) w 5) 8 in} 5 e 4 cl
6 (20) " 18] 0 ina) 8 i 5 a 4 ol
8 3) 10 fa) 8 12] ° i) 4 oI 3 a
2 (10) 8 112) 8 in 6 @ 4 ) 3 a
10 fa) 5 in) 7 £10) 5 my 3 @ 2 a
7 (10) 5 tu 5 tal 4 5) 2 a 2 3
‘Tables iid o 40 tb Because the rlaontip between spacinen size and es eels has been reported Tobe nornear er higher aes.
ANNEXES
(Mandatory Information)
AL. STEEL BAR PRODUCTS
ALA Scope
ALL This annex contains testing requirements for Steet
Bar Products that are specific to the product. The requirements.
contained inthis annex are supplementary to those found inthe
feneral section of this specification, Inthe case of conflict,
between requirements provide in this annex and those found
in the general section of this specification, the requirements of
this annex shall prevail, In the case of conflict between
requirements provided inthis annex and requirements found in
product specifications, the requirements found inthe product
Specification shall preva
A12 Orientation of Test Specimens
A1.2.1 Carbon and alloy steel bars and bar-size shapes, due
to their relatively small cross-sectional dimensions, are cus-
tomarily tested in the longitudinal direction. In special cases
where size permits and the fabrication or service of a part
justifies testing in a transverse direction, the selection and
location of test or fests are a matter of agreement between the
‘manufacturer and the purchaser.
AL3 Tension Test
13.1 Carbon Steel Bars—Carbon stee! bars are not com-
‘monly specified to tensile requirements in the as-rolled condi-
CCopyriht by ASTM I (a igh reserve; Fi Feb 13 09:38:36 EST 2015
Doenoadepriied by
25
tion for sizes of rounds, squares, hexagons, and octagons under
Yein. (13 mm) in diameter or distance between parallel faces
nor for other bar-size sections, other than flats, less than 1 in?
(G45 mm’) in cross-sectional area.
A132 Alloy Steel Bars—Alloy steel bars are usually not
tested in the as-rolled condition
A133 When tension tests are specified, the practice for
selecting test specimens for hot-rolled and cold-finished steel
bars of various sizes shall be in accordance with Table Al.1,
unless otherwise specified in the product specification.
ALA Bend Test
‘AL4.1 When bend tests are specified, the recommended
practice for hot-rolled and cold-finished steel bars shall be in
accordance with Table A1.2,
ALS Hardness Test
ALS.1 Hardness Tests on Bar Products—flats, rounds,
squares, hexagons and octagons—is conducted on the surface
after a minimum removal of 0.015 in. to provide for accurate
hhardness penetration,
(rivet of Witcosin- Madison) pursuant o Liens Agreement No further epedustionsauoried