Professional Documents
Culture Documents
PDS - M-Series - Traditional - IO EMERSON PDF
PDS - M-Series - Traditional - IO EMERSON PDF
www.DeltaV.com
DeltaV Product Data Sheet
October 2014 – Page 2 M-series Traditional I/O
Benefits
Decreases capital equipment costs
Full system modularity. The Traditional I/O
subsystem was designed with your investment in mind. All
components are fully modular and may be installable
under power.1 You add I/O interface carriers and I/O
interfaces in groups of 4, 8, 16, or 32 channels as you
need them. The modular design enables you to purchase
the exact amount of I/O cards, 8-wide carriers,
power/controllers, and 2-wide carriers you need and add
more DeltaV I/O as your system grows.
Product Description A Traditional I/O card easily plugs into an I/O carrier
The Traditional I/O subsystem includes:
I/O interface carrier (a DIN rail surface mounted) on I/O Cards
which all I/O related components are installed. A variety of analog and discrete I/O cards are available to
meet your specific requirements. The following cards
Bulk AC to 24 VDC power supply for field devices. support simplex or redundant installation:
Hardware Specifications
Category Specifications:
Operating temperature -40 to 70 C (-40 to 158 F)
Storage temperature -40 to 85 C (-40 to 185 F)
Relative humidity 5 to 95% , non-condensing
2 Non-incendive field circuits are designed such that under normal operating conditions energy is limited.
DeltaV Product Data Sheet
October 2014 – Page 7 M-series Traditional I/O
Specifications for HART AI-Card 16 Channel, 4 to 20 mA
Number of channels 16
LocalBus current (12 VDC nominal) per Card 85 mA typical, 150 mA maximum
Resolution 16 bits
Repeatability 0.05% of span
Roll off frequency -3 dB at 2.7 Hz;
-20.5 dB at ½ the sampling frequency
Calibration None required
Optional fuse None
Communications support HART pass-through request/response
HART variable reporting
Field device status reporting
Hart Scan Time 600 – 800 ms (typical) per enabled channel
Field wiring 2-wire—non-incendive3
4-wire—non-arcing
2-wire—–nL or ic
4-wire—-nA
3 Non-incendive field circuits are designed such that under normal operating conditions energy is limited.
DeltaV Product Data Sheet
October 2014 – Page 8 M-series Traditional I/O
Specifications for RTD Input Card, 8 channel
RTD channels per card 8
Sensor types 2 wire, 3 wire, or 4 wire
Sensor Configuration Resistance, Pt100, Pt200, Pt500, Ni120, Cu10, User Defined
Full Scale signal range See Table next page
Accuracy See Table next page
Repeatability 0.05% of span
A/D Resolution 16 bit
Calibration None required
Units Degrees C, Degrees F
Sensor excitation current 100 µA
Common mode rejection 120 dB at 50/60 Hz
Common mode impedance > 10 megohms
Roll off Frequency -3db at 3 Hz, -25 db at 30 Hz
LocalBus current (12 VDC nominal) 160 mA
Open sensor detection time 1 second
Open mV Lead detection time 15 second
6 Non-arcing field circuits are designed so that ignition does not occur during normal operation.
7 Non-sparking circuits (-nA) are designed to minimize the risk of occurrence of arcs, sparks, or hot spots capable of creating
ignition hazards during normal operation. Normal operation excludes the removal or insertion of field wiring with circuits
energized.
DeltaV Product Data Sheet
October 2014 – Page 17 M-series Traditional I/O
Specifications for DI Card, 8 channel, 120 VAC, Dry Contact
Number of channels 8
Isolation Each channel is optically isolated from the system at 250
VAC
Detection level for On 1.4 mA
Detection level for Off 0.56 mA
Input Impedance 60 K
LocalBus current (12 VDC 75 mA typical,
nominal) per card 100 mA maximum
Field circuit power per card 15 mA at 120 VAC
Optional fuse 2.0 A
Field wiring 2-wire—non-arcing
Number of channels 4
8Refer to Sequence of Event Product Data Sheet for more information on System capabilities and Sequence of Event data
collection.
DeltaV Product Data Sheet
October 2014 – Page 19 M-series Traditional I/O
9High-side means the output signal is switched on the positive leg. Switching on the positive leg avoids current in field wiring
when there is no output signal.
DeltaV Product Data Sheet
October 2014 – Page 23 M-series Traditional I/O
Fused 8-Channel Terminal Block
The keying mechanism consists of two keying posts that Redundant AO 8-Channel Terminal Block
rotate and lock into the terminal block base. Each post
has 6 positions: A-F and 1-6. Each card is assigned a Redundant Discrete 8-Channel Terminal Block
unique key which is marked on the side of the I/O card:
The table on the following page lists the compatible
terminal blocks for each card, along with the cards unique
key positions. The first terminal block listed is the
recommended terminal block.
I/O Card I/O Card Traditional I/O Terminal Blocks Mass Terminal Blocks
Keying
AI, 8-channel, 4–20 mA, A1 I/O Terminal Block 16-pin Mass Termination Block
HART Fused I/O Terminal Block (Supports 2-wire Devices)
4-wire I/O terminal Block 24-pin Mass Termination Block
(Supports 4-wire Devices)
AI, 16-channel, 4-20 mA A2 AI 16-Channel Terminal Block NA
HART (Simplex mode) 4-wire AI 16-Channel Terminal Block
AO, 8-channel,4–20 mA, A4 I/O Terminal Block 16-pin Mass Termination Block
HART Fused Terminal Block
Thermocouple, mV C1 I/O Terminal Block NA
Cold Junction Compensated (CJC)
Termination Block
RTD, 8-channel C3 Resistant Temperature Device (RTD) NA
Termination Block
Isolated Input Card C2 Isolated Input Terminal Block NA
DI, 8-channel, 24 VDC, B1 I/O Terminal Block 16-pin Mass Termination Block
dry contact Fused Terminal Block
DI, 8-channel, 24 VDC, B2 I/O Terminal Block 16-pin Mass Termination Block
Isolated Fused Terminal Block
DI, 32-channel, 24 VDC B3 32-Channel Terminal Block 40-pin Mass Termination Block
dry contact
PCI, 4-channel C6 32-Channel Terminal Block NA
SOE, 16-channel,24 C5 32-Channel Terminal Block 40-pin Mass Termination Block
VDC
DO, 8-channel, 24 VDC, B6 I/O Terminal Block 10-pin Mass Termination Block
High Side Fused Terminal Block 16-pin Mass Termination Block
DO, 8-channel, 24 VDC, B5 I/O Terminal Block 16-pin Mass Termination Block
isolated Fused Terminal Block
DO, 32-channel, 24 VDC B4 32-Channel Terminal Block 40-pin Mass Termination Block
high-side
DI, 8-channel, 120 VAC, E1 I/O Terminal Block NA
dry contact Fused Terminal Block
DI, 8-channel, 120 VAC, E4 I/O Terminal Block NA
isolated Fused Terminal Block
DO, 8-channel, 120 F1 I/O Terminal Block NA
VAC/ 230 VAC, high side Fused Terminal Block
DO, 8-channel, 120 F4 I/O Terminal Block NA
VAC/ 230 VAC, isolated Fused Terminal Block
DeltaV Product Data Sheet
October 2014 – Page 25 M-series Traditional I/O
Certifications
The following certifications are available for M-series Traditional I/O:
CE:
- EMC- EN 61326-3-1:2006
- LVD: Directive 2006/95/EC Aug 2007
FM:
CSA:
ATEX:
- ATEX 94/9/EC
- EN60079-0: 2009
- EN60079-15:2005
- EN60079-15:2010
IEC-Ex:
- IEC60079-0:2007
- IEC60079-15:2005
- IEC60079-15:2010
Marine Certifications:
- POCC US.ГБ05.B03564
DeltaV Product Data Sheet
October 2014 – Page 26 M-series Traditional I/O
Certifications
M-series Traditional I/O Cards will be submitted for the following certifications:
FM (USA):
cFM (Canada):
ATEX:
IEC-Ex:
Ordering Information
Analog Input Cards and Termination Blocks
Description Model Number
8 Channels 4-20 mA, HART
Standard I/O Termination Block VE4003S2B1
Redundant Standard I/O Termination Block VE4033S2B1
Fused I/O Termination Block VE4003S2B2
4-wire I/O Termination Block VE4003S2B3
16-Pin Mass Termination Block VE4003S2B4
24-Pin Mass Termination Block VE4003S2B5
16 Channels 4-20 mA, HART
Standard I/O Termination Block VE4003S2B6
4-wire I/O Termination Block VE4003S2B7
8 Channels Thermocouple,mV
Standard I/O Termination Block VE4003S4B1
Cold Junction Compensated (CJC) Termination Block VE4003S5B1
Analog Input Card: 8 Channels RTD
Resistant Temperature Device (RTD) Termination Block VE4003S6B1
Isolated Input Card
Isolated Input terminal Block VE4003S7B1
* For more Details on the DI Mass Connection Board and Connection cables, please refere to the PDS M-series Mass
Connection Solution
DeltaV Product Data Sheet
October 2014 – Page 31 M-series Traditional I/O
Discrete Output Cards and Termination Blocks
Description Model Number
Discrete Output Card: 8 Channels 24Vdc, Isolated
Standard I/O Termination Block VE4002S1T1B1
Fused I/O Termination Block VE4002S1T1B2
16-Pin Mass Termination Block VE4002S1T1B3
Discrete Output Card: 8 Channels 24Vdc, High Side
Standard I/O Termination Block VE4002S1T2B1
Redundant Standard I/O Termination Block VE4032S1T2B1
Fused I/O Termination Block VE4002S1T2B2
16-Pin Mass Termination Block VE4002S1T2B3
10-Pin Mass Termination Block VE4002S1T2B4
Discrete Output Card, 32 Channels, 24Vdc, High Side
Standard I/O Termination Block VE4002S1T2B5
40-Pin Mass Termination Block VE4002S1T2B6
40-pin Mass Termination Block and 2 x 16 Channel DO MASS CONNECTION VE4052S1T2B6
BOARDs*
Discrete Output Card: 8 Channels 115/230Vac, Isolated
Standard I/O Termination Block VE4002S2T1B1
Fused I/O Termination Block VE4002S2T1B2
Discrete Output Card: 8 Channels 115/230Vac, High Side
Standard I/O Termination Block VE4002S2T2B1
Fused I/O Termination Block VE4002S2T2B2
* For more Details on the DO Mass Connection Board and Connection cables, please refere to the PDS M-series Mass
Connection Solution
DeltaV Product Data Sheet
October 2014 – Page 32 M-series Traditional I/O
Spare part ordering Information
Spare Parts
Description Model Number
250V 2A Fuse for Fused Terminal Block; Box of 20 KJ4010X1-BC1
To locate a sales office near you, visit our website at: For large power, water, and wastewater applications
www.EmersonProcess.com/DeltaV contact Power and Water Solutions at:
Or call us at: www.EmersonProcess-powerwater.com
Asia Pacific: 65.6777.8211 Or call us at:
Europe, Middle East: 41.41.768.6111 Asia Pacific: 65.6777.8211
North America, Latin America: +1 800.833.8314 or Europe, Middle East, Africa: 48.22.630.2443
+1 512.832.3774 North America, Latin America: +1 412.963.4000
© Emerson Process Management 2013. All rights reserved. For Emerson Process Management trademarks and service marks, go to:
http://www.emersonprocess.com/home/news/resources/marks.pdf.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be
construed as warrantees or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed
by our terms and conditions, which are available on request. We reserve the right to modify or improve the design or specification of such products at any time
without notice.
www.DeltaV.com