Professional Documents
Culture Documents
Procedure:
Part I. Melting Point Determination of Alum
1. pulverize a small amount (about 0.5 g) of dry alum using a mortar and pestle
2. Pack the alum in a capillary tube to a depth of about 0.5 cm.
3. Turn the tube so the open end is up and bounce the bottom of the tube on the desk.
4. Fasten the capillary tube to the thermometer with a rubber band. Alum should be level with the
thermometer bulb
5. Using a thermometer clamp or a universal clamp and notched cork stopper (or split rubber stopper),
fasten the thermometer to a ring stand.
6. Immerse bottom of capillary and thermometer in a beaker of water and heat. Slow the heat of the
water bath as the temperature approaches the melting point of alum in order to get an accurate
temperature reading of the melting point.
Materials for Part 1
7. Record the temperature range.
-beaker, 150 mL / Thiele
8. Repeat again, using a new sample of alum and capillary tube.
-Capillary tubes, 22
Part II. Determination of the Water of Hydration in Alum Crystals. -mortar and pestle
1. Set up Bunsen burner on ring stand beneath ring clamp. -notched stopper to hold
2. Adjust height of ring clamp to 1 cm above the burner. thermometer
3. Place crucible with cover in clay triangle and heat over burner -rubber bands
until red hot. -thermometer
4. Turn off gas and remove burner -clamp
5. Remove crucible and place on wire gauze with crucible tongs. Materials for Part 2
6. Allow crucible and cover to cool for 10 mins minimum -balance
7. Find mass using balance scale. Handle with tongs -Crucible and cover 15-30 mL
-crucible tongs
8. Record mass
-ring support
9. Add 2g alum crystals to crucible. Weigh.
-triangle, pipe stem
10. Set crucible at an angle and heat gently to remove the water -wire gauze
of hydration. Materials for Both Part 1 and Part 2
11. After bubbling stops, heat strongly for 5 mins -gloves
12. Turn off gas and remove burner -apron
13. Remove crucible with tongs and place on gauze. -goggles
14. Let cool for 10 mins -Aluminum potassium sulfate,
15. Measure and record mass of crucible, cover, and anhydrous AlK(SO4)2*12H2O, 2.5g
alum -bunsen burner
16. Repeat drying it until a constant mass is obtained -ring stand
17. Record final mass
18. Dispose anhydrous alum and clean crucible.
Analysis and Calculations:
Result/Conclusion
The experiment, which consisted of finding the samples melting point and water of hydration, was conducted in
an effort to determine and analyze whether the sample given was indeed alum. Results of the experiment indicated that
the melting point was 91.4 C. Compared to the class average of 93.1 C our results were relatively accurate (the class
average includes the outlier from Group 6). Otherwise the average would be 92.23 C without the deviant. Compared to
the literature value of 92.5 C, our results would be considered accurate, although the class average would be accurate
and precise.
Our percent error (100 - [(Measured melting point) / (Literature melting point) * 100]) is 1.18% and the class average
percent error (with group 6) is 0.649% and without group 6 would be 0.292%. The results of the experiment also
indicated that the ratio of AlK(SO4)2 to water was 14.936. The literature value reveals that it is 12. Therefore our
percent error (100 * (((Mole ratio) - (actual mole ratio)) / (actual mole ratio))) is 24.46% and the class average of 14.032 has a
percent error of 16.93%. The outlier, 11.8 is surprisingly the closest one to the literature value with a percent error of 1.67%.
Although there was some margin of error, the experiment has generally proven that the sample was indeed alum.
Error Analysis
There were several possible sources of errors while performing the experiment. While figuring out the melting
point for the alum crystals, it was difficult to determine whether the alum crystals started to melt exactly due to the
boiling bubbles that obstructed the view of the capillary tube. Observing the melting point of alum in the experiment
was precise but not accurate since the exact point where the alum melts wasn’t really observable through the human
eye. During the process of melting the alum, we did not stir while it was heating, which may have caused some
unevenness in heat distribution. Also, the first trial we heated the sample too quickly which may have caused
inaccuracies in determining the melting point of the alum. Because it was hard to tell whether it melted or not, and
because we did not know what to expect when it should melt, our first trial was heated too quickly, and a lot of it
evaporated. The second trial revealed that we added 1 cm alum instead of 0.5 cm. Although I do not believe the
quanitity of alum would affect its melting point, it may have be altered the data slightly due to the different masses
between trial one and trial two.
The experiment may have had an error when dehydrating the alum. The alum may have not fully dehydrated,
therefore it would cause the mass of anhydrous alum to increase which lead to the increase of the mole ration. In order
to prevent this from happening again, the heating time should extend to at least 15 minutes. The mass of the crucible,
cover, and anhydrous alum may also have errors since the crucible wasn’t completely cool at room temperature due to
the time constraints of the class period. A way to resolve this issue is to use a fan to speed up the process of lowering
the temperature of the crucible to room temperature in order to reduce the error of the mass of the crucible, cover, and
anhydrous alum.