T1823/T1479_ STRENGTH OF MATERIALS
Q. P. Code : 555000
ou) o9) 20r+
S.E. SEM - Ill / MECH / CBGS / MAY 2017
‘Time: 3hrs Marks: 80
Instructions 1. All questions carry equal marks
2 Assume suitable dat if necessary.
3. Figures wo the right inate full marks
3. Question No, | is compulsory & Attempt any three questions from remaining five questo
Qu Attempt any FOUR
a. What do you mean by Core of a section’? Obtain the core of a hollow
section.
b. Draw SFD and BMD for a simply supported beam carrying udl (w) Qyer the full
span (L).
¢. Derive flexural formula @
d. Establish the relationship between Young's modulus, Modulug of rigidity and Bulk
modulus,
€. Derive an expression for the elongation of bar having, wrsection due to its
self-weight.
f. A rectangular beam 300 mm deep is simply support es a span of 4 m, What udl
0 MPa.
the beam can carry if the bending stress is not to ex6e«
Take 1=8 x 10mm‘, a
Q2 a A beam has a cross section in the form les triangle with the base 90mm _— 8
and height 150 mm, If the maximum ¥ issible shear stress is 0.8 MPa,
what is the maximum value of ae ree the section can withstand? Also
fot
determine shearing stresses at 40) ‘apex and at centroid of the triangle.
b. Write the assumptions ma of torsion and derive torsional formula. 6
A rod of 16 mm «62 stretched by 4 mm under a steady axial load of 6
x
15 KN. What stresgswouléhbe induced in a bar by a 900 N weight falling through 60
mm, ifitis sive Take E=2x10° MPa,
3 a. A cylindrical shéll ig’3 m long, 1 m in diameter is subjected to an intemal pressure 10
ng, a pr
of 1 MPa. thickness of the shell is 12 mm, find the change in length,
diamet lume of the shell. Take I/m = 0.27 and E = 2.x 10° N/mm’,
b A
teh age overhead cable 100 m long consists of six strands of 3 mm diameter 10
%, eniclosed by 28 strands of 2 mm diameter aluminium wire. If the cable is
cted to a tensile force of 8 KN. Find the stresses in each material and extension
ie cable. Take Fs = 190 GPa, Ea = 68 GPa
[TURN OVER]
7879AB9R48BCA74B209B1S2BS010F2EA‘T1823 /T1479_ STRENGTH OF MATERIALS
Q. P. Code : 555000
Q4 a, Find slope and deflection at B, C, and D. for the beam shown in Figure 1. 10
Figure 1
b. A short column has « hollow circular cross section of outside diame 230% and 10
wall thickness 30 mm, An axial compressive load of 400 kN is i gether
with a parallel compressive load of 300 kN offset 100 mm fromthe axi!
i) Calculate the maximum tensile and maximum comy Messes in the
column,
ii) Determine the maximum eccentricity that the Joad can have for no
tension condition.
Q5 a. Determine the crippling load for a T section hi ensions 100 mm x 100mm 10
x 20 mm and length is 5 m, when it is used as" both the ends hinged. Take
E= 2x 10° MPa.
b. A bimetallic thermal contro! shows
‘mm and cross sectional area 100
ross sectional area 200 mm’,
made of brass bar of length 750 10
agnesium bar of length 1300 mm and
their free ends is 2 mm at rogmh tempigsatue, Calculate
i) The temperature 4 ich the two bars come in contact.
ii) The stress in thes Is when the temperature increase is 300°C.
take Es = = 65 GPa, an = 10x 10° °C, am = 14.5 x 10% °C.
= aos ot
[TURN OVER]
‘7879 AB9848BCA74B209B | S2BSOL0F2EAT1823 /T1479_ STRENGTH OF MATERIALS.
Q. P. Code : 555000
3
Q6 a. A beam simply supported at its ends has a span of 6 m. It is loaded with a gradually 6
varying load of zero from left hand support to 1500 N/m to the right hand support.
Draw SFD and BMD.
b. A beam 8.5 m Jong rests on the supports 5 m apart, the beam carries load as shown 10
in Figure 3. Draw SFD and BMD showing all the important points,
40KN SOKN. son
Figure 3
¢. Find the maximum power that can be transmitted by a SO myff'diameter shaft at 4
200 rpm, if the permissible shear stress for the shaft material i .
‘7879ABO848BCA74B209B S2BS010F2EA