Professional Documents
Culture Documents
Dwa 6 PDF
Dwa 6 PDF
BMW Motorrad
The Ultimate
Riding Machine
*01417714371*
BMW Motorrad.
General instructions
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1
3
Abbreviations and symbols . . . . . . . . . . 4
Currency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Technical data . . . . . . . . . . . . . . . . . . . . . . . 4
General instructions
z
Overview
General information about the anti-
2
theft alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Overview
z
trigger the alarm. The sensitivity as the remote control of the anti-
of the system is parameterised theft alarm can interfere with op-
so that slight vibrations will not eration of the system. If prob-
trigger the alarm. Once the sys- lems of this nature occur, point 1 Left button (ribbed) ( 8)
z the remote control toward the
tem has been activated, any at- 2 Right button ( 9)
tempt to tamper with the motor- motorcycle from another direc- 3 LED
cycle is indicated acoustically by tion.
the siren and visually by all four See your Rider's Manual
turn indicators flashing in unison. for details of the position of
the status-indicator LED on the
You can change some of your
motorcycle.
alarm system's parameters to suit
your personal preferences.
Operation
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3
7
Alarm function . . . . . . . . . . . . . . . . . . . . . . . 9
Deactivation . . . . . . . . . . . . . . . . . . . . . . . . 10
Programming . . . . . . . . . . . . . . . . . . . . . . . 11
Operation
Registration of the remote con-
trol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Synchronisation . . . . . . . . . . . . . . . . . . . . . 14
z
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operation
an attempt to disconnect the
anti-theft alarm from the starter
battery (the built-in battery in
the anti-theft alarm automatic- An alarm lasts for 26 seconds.
Press button 1 on the remote ally cuts in to provide power) The system is active again an- z
control a second time during other 12 seconds later. You can
the activation phase. interrupt an alarm at any time by
Turn indicators flash three pressing button 2 on the remote
times. control. This function does not
Alarm tone sounds three times. change the status of the anti-
Motion sensor is deactivated. theft alarm.
While an alarm is in progress an
alarm tone sounds and the turn
indicators flash. You can program
the type of alarm tone.
Operation
alarm: Programming anti-theft three times.
Confirmation alarm tone after alarm
activation/deactivation of the The programming function is
anti-theft alarm in addition to active.
Programming is a sequence of
visual confirmation by turn in-
four steps, although no function
z
dicators flashing
Rising and falling or intermittent is assigned to step No. 2. The
alarm tone number of times the anti-theft
alarm telltale light on the mo-
Automatic activation of the
torcycle flashes indicates which
alarm function after the ignition
step in the programming se-
is switched off
quence is active. An alarm tone
Default settings Deactivate the alarm function. sounds as confirmation when
Switch on the ignition. you press button 1; an acknow-
The anti-theft alarm ships with
ledgement tone sounds when
the following default settings: Press button 1 three times.
you press button 2.
Acknowledgement tone sounds
once.
or automatically 30 seconds
Press button 2. programming aborted?
after completion of the last
Step 2: Programming is aborted step in the programming se-
There is no function assigned to if the ignition is switched off quence
before completion of the last
z this step.
step in the programming se- The anti-theft alarm telltale light
Press button 1 or button 2.
quence stops flashing and four acknow-
Step 3: Which alarm tone do or automatically, if more than ledgement tones sound.
you want to use? 30 seconds elapse between
Rising and falling: any two steps in the program- Registration of the
Press button 1. ming sequence. remote control
Intermittent: The new settings are not saved if When is it necessary to
Press button 2. programming is aborted. register a remote control?
If you want to register an addi-
Step 4: Do you want to have tional remote control or register
the alarm function activated a remote control as a replace-
automatically after the ignition ment for one that has been mis-
is switched off? laid, you must always register all
Operation
button being pressed after the
the anti-theft alarm. Registration ignition has been switched off
is a three-step process for each
30 seconds elapse without a
remote control.
button being pressed after a
Press and hold down button 1
and button 2.
remote control unit has been z
registered
LED flashes for ten seconds.
As soon as the LED goes out, When registration terminates the
release button 1 and button 2. LED flashes and the acknow-
Deactivate the alarm function. LED lights up. ledgement tone sounds three
Switch on the ignition. Press button 1 or button 2. times.
Press button 2 three times. Alarm tone sounds once.
Acknowledgement tone sounds LED goes out.
once. Remote control has been re-
Within ten seconds, switch off gistered.
the ignition. Repeat this three-step proced-
Press button 2 three times. ure for each additional remote
control.
pressed more than 256 times LED does not light up or lights
outside the receiver's range. up only briefly when a button is
Once this limit has been reached, pressed.
the receiver on the motorcycle
z will no longer react to the signals Press and hold down button 1 Changing battery
from the remote control. and button 2.
LED flashes for ten seconds.
As soon as the LED goes out,
release button 1 and button 2.
LED lights up.
Press button 1 or button 2.
LED goes out.
Remote control has been syn-
chronised.
Remove screw 4 and remove
bottom part of housing 5.
Slide old battery 8 forward
from under retainer 6.
Operation
always make sure polarity is
correct. To synchronise the remote
Slip the new battery into posi- control, make sure that it is
tion, making sure that the pos- within range of the receiver and z
itive terminal of the battery is press button 1 twice.
facing up. LED 3 starts flashing and then
Position the bottom part of the goes out after a few seconds.
housing at projection 9 of the The remote control is again
front edge and close the hous- ready for use.
ing, noting two guide pins 7.
Install screw 4.
The LED on the remote con-
trol lights up, indicating that the
remote control has to be syn-
chronised.
Technical data
Anti-theft alarm . . . . . . . . . . . . . . . . . . . . . 18
4
17
Remote control . . . . . . . . . . . . . . . . . . . . . 18
Technical data
z
Remote control
Range of the remote control 10 m
Reception standby for signal from remote control 1 h, After ignition off
z Signal frequency 25 kHz, Broadband
Transmission frequency 433.92 MHz
Operating voltage 3V
Battery type CR 2032
Battery type Lithium
B T
Index
Battery Technical data
changing, 14 Standards, 4
z
C
Currency, 4
D
Deactivating
Alarm, 10
Motion sensor, 9
Default settings, 11
M
Motion sensor
Deactivating, 9
P
Programming, 11