Professional Documents
Culture Documents
Es 13 Prob Set 2
Es 13 Prob Set 2
P
θ B
800 mm
A
C
800 mm 600 mm
2. Bar ABCD is subjected to the following loads as shown. Determine the maximum
value of force P that can be applied to the bar if σallow used for design is based on
ultimate strength and δallow (of bar ABCD) = ±1.2 mm.
Note: Member AB at inner diameter is hollow.
Aluminum Steel
Copper
Properties Aluminum Copper Steel
E (GPa) 70 120 200
σyp (MPa) 180 200 300
σult (MPa) 310 400 580
FS 2 4 3
Bar AC:
E = 200 GPa
A = 200 mm2
Determine
a. σavg in each bar (AB, AC, and AD)
b. Force in the strut AE
2. In the figure shown below, each of the two vertical steel posts (E = 200 GPa, α =
12×10-6/°C) has a height of 300 mm and a diameter of 50 mm. If the springs each has a
stiffness of 0.5 kN/m, determine the resulting stress in the steel posts if the temperature
is raised by 70°C. Assume that springs are initially unstretched. Neglect the masses of
the rigid members.
3. The respective ends of three wires are joined together as shown. Each wire has a cross-
sectional area of 3 mm2 and E=200 GPa. The lengths of the wires are 4 m, 4.002 m, and
4.003 m. The three wires carry a total load of 1000 N.
•
P
Determine:
a. The deformation of the shortest wire
b. The tension in the most stressed wire
c. The tension in the least stressed wire
4. An aluminum cylinder and a bronze cylinder are centered and secured between two rigid
slabs by tightening two steel bolts as shown below.
Hint: Though slabs are rigid, please take note that they are free to move (or be
displaced).
At 10°C no axial loads exist in the assembly. The weight of all components in the
assembly can be assumed negligible. The geometric and material properties of the
different bars are given in the table below:
If the temperature of the entire assembly is increased to 90°C, and the internal force and
deformation in the two steel bars are the same due to symmetry, determine the following:
i. Given that the force in each of the steel bars is the same, what is the degree of static
indeterminacy of the assembly? Explain why.
a. 0
b. 1
c. 2
d. 3
ii. If the force in each of the steel bars is PS , the force in the aluminum bar is PA , and the
force in the bronze bar is PB , which of the following statements is false? Explain your
answer.
a. 2 PS + PA = 0
b. 2 PS + PB = 0
c. PA = PB
d. PA + PB − 2 PS = 0
iii. If δ A , δ B ,and δ S are the change in length in the aluminum, brass and steel bar due to
internal forces PA , PB and PS respectively, and δ TA| , δ TB ,and δ TS are the change in
length in the aluminum, brass and steel bar respectively due to the increase in
temperature from 10°C to 90°C, which of the following statements false? Explain each
choice and why it is true/false.
a. δ TA| , δ TB , and δ TS will always be positive, since all bars will expand due to an
increase in temperature.
b. δTA = α A LAΔT where α A is the coefficient of thermal expansion of aluminum, LA is
equal to the initial length of the aluminum bar before the temperature was
increased, and ΔT is the increase in temperature which in this case is equal to 80
C°.
PL
c. δ s = s s , where Ps is the internal force in each of the steel bars, LS is equal to the
As Es
initial length of the steel bar before the temperature was increased, and As is the
cross sectional area of the steel bar, and Es is the modulus of elasticity of the steel
bar.
d. 2 (δTS + δ S ) = (δTA + δTB ) − (δ A + δ B )
iv. Which force given below is closest to the internal force in the steel bar after the
temperature is increased from 10°C to 90°C? Show your solution to support your
answer.
a. 8.3 kN c. 33.2 kN
b. 16.6 kN d. 66.4 kN
v. Which stress is closest to the stress in the bronze bar after the temperature is increased
from 10°C to 90°C? Show your solution to support your answer.
a. 16.6 MPa compressive c. 33.2 MPa compressive
b. 27.66 MPa compressive d. 66.4 MPa compressive
2. A hollow rod (G = 80 GPa) is bent as shown in figure below to support a homogeneous plate
weighing 300 N. If the rod has an outer diameter of 50 mm, an inner diameter of 40 mm and
a linear mass density of 9 kg/m, determine:
a. The maximum shear stress due to torsion at a section through a.
b. The maximum angle-of-twist for segment AB of the rod.
Fixed
support
3. Hibbeler, RC. Mechanics of Materials. International Edition, 4th Ed. Problem 5-56. Use G =
85 GPa.
*Please take the problem from the edition specified since numbering may vary for different
editions.
Bonus:
1. Determine the moment of inertia Ix and Iy at the centroidal axes of the section. (2 pts)
x
2. Draw the shear and bending moment diagram of the figure below. (3 pts)
25 kN·m 10 kN/m
∙
A B C D E
1m 1m 3m 1m
a.
b.
"What else does this craving, and this helplessness, proclaim but that there was once in man a
true happiness, of which all that now remains is the empty print and trace? This he tries in vain
to fill with everything around him, seeking in things that are not there the help he cannot find in
those that are, though none can help, since this infinite abyss can be filled only with an infinite
and immutable object; in other words by God himself."