Specification 2001-11
‘Class: Plastics Class No.:25
VWABCO | Thermoplastic Polymer on the Basis of
Polyamide 6.6 (PA 6.6), toughness modified JED
326
Prev Eaton | Abbreviated Te
1989-08 | PAB.6, toughned 852.003 260 4
1 Scope
This specification deals with polymers increased impact resistance.
There are the following types:
JED-326-0 with very high impact resistance in wet and dry condition, for parts that are not exposed
to the outside atmosphere, colour natural (if not indicated on the drawing);
JED-326-1_with very high impact resistance in wet and dry condition, for parts that are exposed to
the outside atmosphere, UV-r tant, colour black;
JED-326-2 with improved impact resistance in dry condition, for parts that are not exposed to the
outside atmosphere, colour natural (if not indicated on the drawing);
JED-326-3 with improved impact resistance in dry condition, for parts that are exposed to the
‘outside atmosphere, UV-resistant, colour black.
If JED-326 is indicated on the drawing, JED-326-0 shall be applied
2 General requirements
The finished parts shall be homogeneous and free from pores, blisters, and other defects. The parts
must not show any defects such as cracks, voids etc. within their structure.
The requirements for finished parts can be taken from the drawing, the corresponding part specification]
and the technical conditions of delivery JED-367 established by WABCO.
All materials, even ingredients in small quantities (e. g. cadmium), which are detrimental to health or to
the environment are banned from being used.
3 Thermal range of application
Continuous operational temperature range:
JED-326-0a.-1: -40°C to +90°C
JED-326-2a.-3: 40°C to +100 °C
Short-term exposure to heat: that+120°C
Continuation page 2 to 4
Aporoved Grou Stndards Responsible for ho Ganiaris TR 002
by du Us Doc. Gree iJED-326 : 2001-11 Page 2
4 Physical properties
The nominal values given on the following sheets are to be determined according to the test methods
specified. They refer to materials of equilibrium moisture content at 23 °C and 50 % relative humidity.
5 Initial sampling
‘At new presentation of a material according to this specification, its technical data must be indicated
(range and mean values according to ISO 2602)
20 test samples (type 1, ISO 527) have to be made available. Whenever possible, these test samples
should be produced by injection moulding into a tool of the appropriate shape.
The supplier guarantees the customer the indicated technical data for all deliveries according to this
specification.
6 Release of a material
After positive result of the test sample inspection, finished parts are ordered extra for the validation
tests (life tests). The release — which only refers to parts coming from this particular mould — is made in
case of positive result of these tests.
‘Any modification of the material, ofits ingredients or of the manufacturing process parameters of
material or finished parts — no matter of which kind or for which reason — is only permissible after
previous release by the department which is responsible for the technical design.
7 Conditions of delivery
The material and the finished parts must correspond to the technical conditions of delivery specified in
JED-367.
WABCO SpecificationJED-326 : 2001-11 Page 3
Properties Test Method Unit
Tastics acc. to ISO 1043,
feinforcement, nature F = =
einforcement, average size F - um
einforcement, content E = %
olour: ‘according 10 type. =
Infrared spectrum FE ‘according to diagram to be S
delivered with samples
[Content of regenerated material F 0 %
Density iSO 1783 7,08 £0.02 | 4,1020,02 | glom*
[Ball indentation hardness ISO 20307 50 £10 7oz10 | Nimmé
ISO 868 = = Shore D
felting point ISO 3146 25525 °C
|Mett flow index (230/2,16) Iso 1133 = .g/10 min
[10.1 Temperature of deflection under load [iSO 75-2
thod A (1,85 Nimm?) 260 °C
thod B (0,45 Nimm*) > 180 °c
|10.2 Vicat softening temperature ISO 306
lethod A = °c
lethod B = °c
l17 (Coefficient of finear thermal expansion, [ASTM D 696
Wverage value between
°C and +80 °C
|14.1 lirection of reinforcement or flow 910 12 405K1
[11.2 perpendicular to direction of 91012 105K"
einforcement or flow
[12 Shrinkage at moulding JASTM D 955,
}12.1 jn direction of flow 1102 %
}12.2 perpendicular to direction of flow to2 %
[12.3 postshrinkage after moulding %
11000 h at 80 °C
[13.1 Water content at delivery TMD 570 52 =2 %
[13.2 water absorption in air at TMD 570 | 2.2405) | 252059 | %
23 *CI50 % relative humidity
[13.3 Water absorption at 23 °C Iso 62 674057 | 8+0,5° %
[14 Yield stress \so527 235 250 Nim?
Stress at break = 7 Nim
test speed - - mm/min
[i Strain at yield 1SO.527 235 215 %
‘Strain at break = - %
fest speed 7 = mm/min
[16 E-Modulus (bending test) 1SO.176 = = Ninm?
17 E-Modulus (tensile test), ISO 527 = 800 = 1300 Nimm?
test speed = = mm/min
[18 zod impact strength (notched) ISO 180
fat +23 °C > 100 213 kim?
at o°C - 7 kim?
30°C 215 = kim?
[iS Flammability test iL-94 HB
saturation
WABCO Specification