Professional Documents
Culture Documents
Acrylic
PRODUCT A single component, fast drying, modified acrylic finish.
DESCRIPTION
INTENDED USES As a sealer coat for single pack acrylic intumescent coating systems.
Theoretical Coverage 8.80 m²/litre at 40 microns d.f.t and stated volume solids
351 sq.ft/US gallon at 1.6 mils d.f.t and stated volume solids
Drying Time
Overcoating Interval with
recommended topcoats
Temperature Touch Dry Hard Dry Minimum Maximum
Protective Coatings
Page 1 of 4
Issue Date:28/06/2011
Ref:2403
Intersheen® 579
Acrylic
SURFACE Intumescent Coatings
PREPARATION
Intumescent coatings should be checked for required dry film thickness prior to application of
Intersheen 579 and should be clean, dry and free of loose material or other surface contamination.
Please see the Interchar Working Procedures for further information on optimum overcoating
intervals.
Primed Steelwork
Intersheen 579 can be applied over approved anti-corrosive primers. The primer surface should be
dry and free from all contamination and Intersheen 579 must be applied within the overcoating
intervals specified (consult the relevant product data sheet).
Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO
8501-1:2007) or SSPC-SP10 Abrasive Blasting, or SSPC-SP11, Power Tool Cleaning) and patch
primed prior to the application of Intersheen 579
APPLICATION Mixing This material is a one component coating and should always be mixed
thoroughly with a power agitator before application.
Clean Up Clean all equipment immediately after use with International GTA007. It is
good working practice to periodically flush out spray equipment during the
course of the working day. Frequency of cleaning will depend upon amount
sprayed, temperature and elapsed time, including any delays.
Page 2 of 4
Intersheen® 579
Acrylic
PRODUCT Surface temperature must always be a minimum of 3°C (5°F) above dew point. Ensure adequate
CHARACTERISTICS ventilation is provided throughout application and curing.
Intersheen 579 may also be used as a cosmetic finish over single pack primers and intermediates
Intersheen 579 should be protected from pooling or running water, condensation/high humidity and
chemical attack at all times.When Intersheen 579 is being used as a sealer coat for intumescent
coatings, the complete system is not suitable for exposure in environments more aggressive than
C3 (as defined in ISO 12944 Part 2). See the Acrylic Intumescent Working Procedures for further
information.
Level of sheen and surface finish are dependent on application method. Avoid using a mixture of
application methods whenever possible. Condensation occurring during or immediately after
application may result in a matt finish and an inferior film.
Intersheen 579 is certified as M1 according to Spanish standards UNE 23.727-90 (Reaction to fire)
and UNE 23721-90 (Radiation).
Note: VOC values are typical and are provided for guidance purpose only. These may be subject
to variation depending on factors such as differences in colour and normal manufacturing
tolerances.
Page 3 of 4
Intersheen® 579
Acrylic
D ADDITIONAL Further information regarding industry standards, terms and abbreviations used in this data sheet
et INFORMATION can be found in the following documents available at www.international-pc.com:
ail
T • Definitions & Abbreviations
o
p • Surface Preparation
• Paint Application
SAFETY This product is intended for use only by professional applicators in industrial situations in
PRECAUTIONS accordance with the advice given on this sheet, the Material Safety Data Sheet and the
container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS)
which International Protective Coatings has provided to its customers.
All work involving the application and use of this product should be performed in compliance with all
relevant national, Health, Safety & Environmental standards and regulations.
In the event welding or flame cutting is performed on metal coated with this product, dust and
fumes will be emitted which will require the use of appropriate personal protective equipment and
adequate local exhaust ventilation.
If in doubt regarding the suitability of use of this product, consult International Protective Coatings
for further advice.
Rect Top
PACK SIZE Unit Size
Vol Pack
20 litre 20 litre 20 litre
, International and all product names mentioned in this publication are trademarks of, or licensed to, AkzoNobel.
www.international-pc.com
Page 4 of 4