Professional Documents
Culture Documents
Relé de Segurança Schneider PDF
Relé de Segurança Schneider PDF
com
FR EN DE
13 23 24 33
A1 S33 S34 S39
13 23 24 33
A1 S33 S34 S39
24 33
13 233 S34 S39
A1 S3
24 33
13 23 3 S34 S39 A«
A1 S3 »P RE
VE NT
AF
XP S -
TY PE A1/A2
Fuse
A« K1
VE NT
»P RE - AF
XP S K2
TY PE A1/A2
Fuse 33
13 23
K1
K1
K2
K2 34
33 14 24
13 23
1 S12
K1 A2 S11 S22 34
K2 34 14 S2
14 24
2
S1 1 S12 34
A2 1 S2
4 S2
XPS-AF.... XPS-AF....P
S1A28737.00
09 - 12 - 2009
1 / 12
XPS-AF / Series B
Module de surveillance pour circuits d'ARRET D'URGENCE
FRANÇAIS • Module de surveillance conformément à EN / IEC 60204-1, EN ISO /
ISO 13850 pour le contrôle de l’arrêt d’urgence.
ATTENTION
l’installation / de la machine selon les normes applicables.
• Le module contient des relais électromécaniques. Par conséquent le
DANGER À L´INSTALLATION niveau de performance déclaré et sa valeur MTTFd dépendent de la
Respectez les mesures de sécurité suivantes avant charge et de la fréquence de manœuvre dans le cas d’utilisation. Les
l’installation / le montage ou le démontage : valeurs niveau de performance et MTTFd mentionnées ci-dessus
sont valables pour charge nominale et maximum 6 336 manœuvres
1. Débranchez l’appareil / le système avant de commencer les travaux ! par an ou pour charge faible et maximum 316 800 manœuvres / an.
2. Protégez la machine / le système contre les redémarrages • Lorsque la charge électrique est connue, le diagramme de durée de
intempestifs ! vie électrique (voir pages 9/12) doit être utilisé pour calculer le
3. Assurez-vous que la machine est hors tension ! nombre de manœuvres maximum. Le niveau de performance
indiqué est uniquement garantit pour le nombre de manœuvres
4. Reliez les phases à la terre et court-circuitez les !
à déterminer. Après atteinte de ce nombre de manœuvres,
5. Couvrez et isolez les pièces voisines sous tension ! l'appareil doit être remplacé. La durée de vie de l’appareil ne
6. Le montage des appareils doit être effectué dans une armoire doit cependant pas être dépassée.
électrique avec une classe de protection min. IP 54. • L’utilisation de l’appareil non conforme aux spécifications peut
Le non-respect de cette directive peut entraîner des lésions provoquer des dysfonctionnements ou la destruction de l’appareil.
corporelles et/ou des dommages matériels. • L’entrée d’alimentation A1 constitue l’entrée de commande. Ainsi, de
brèves interruptions ou une baisse de la plage de tension de service
UB peut entraîner la commutation des contacts de sortie.
ATTENTION • Pour la duplication des contacts de sortie, il est possible d’utiliser
PROTECTION PARTIELLE CONTRE LES CONTACTS des blocs d’extension ou des contacteurs-disjoncteurs externes avec
ACCIDENTELS des contacts à guidage forcé.
• Classe de protection selon EN/IEC 60529. • Avant d’activer le poussoir de reset, la chaîne de l’arrêt d’urgence
doit être fermée.
• Boîtier / bornes : IP 40 / IP 20.
• Lors de la connexion de commutateurs magnétiques avec les
• Protection des doigts selon EN 50274. contacts reed ou de détecteurs avec les sorties de semi-
Le non-respect de cette directive peut entraîner des lésions conducteurs, faire attention au courant de pointe à l'entrée (voir
corporelles et/ou des dommages matériels. Caractéristiques techniques).
• Respecter le schéma des installation notes.
Application
Le module XPS-AF sert à interrompre en toute sécurité un ou plusieurs
circuits, et est conçu pour les applications suivantes: Note:
• Démarrage manuel ou automatique Observez également les informations de votre caisse de prévoyance
• 3 contacts de sortie, 1 contact de signalisation contre les accidents !
• Boucle de rétroaction pour le contrôle de contacteurs-disjoncteurs
externes
2 / 12
XPS-AF / Series B
Note:
Le module ne contient pas de composants soumis à maintenance par
CAUTION
l'utilisateur. Pour l'autorisation d'un circuit de sécurité selon RISKS ON INSTALLATION
EN / IEC 60204-1, EN ISO / ISO 13850 il est impératif d'utiliser Perform the following precautionary steps prior to installation, assembly,
seulement les circuits de sortie libres de potentiel entre les bornes or disassembly:
13-14, 23-24 et 33-34.
1. Disconnect supply voltage to the equipment / system prior to starting
any work!
3 / 12
XPS-AF / Series B
Proper Use
The device is for monitoring sensors (e.g. emergency stop buttons,
position switches) that are used as part of the safety equipment of WARNING
machines for the purpose of protecting people, material and machinery. IMPROPER CIRCUIT AND MAINTENANCE
• Wire safety relay using wiring diagram shown in following wiring
Note: diagram.
• The performance level and safety category in accordance with • Wire to meet applicable standards requirements.
EN ISO / ISO 13849-1 depends on the external wiring, the
application case, the choice of control station and how this is • K3 and K4 must have mechanically-linked contacts.
physically arranged on the machine. • Strictly follow prescribed maintenance schedule when making
• The user must carry out a risk assessment in accordance with adjustments to and maintenance of machine.
EN ISO / ISO 14121-1. Failure to follow this instruction can result in death, serious injury,
• The entire system/machine must undergo validation in accordance or equipment damage.
with the applicable standards on the basis of this.
• The module contains electro-mechanical relays. Therefore his
indicated performance level and his MTTFd value depend on the load DEUTSCH
and on the operating cycles in the application. The above mentioned
performance level and MTTFd values are suitable for nominal load
and maximum 6.336 switching cycles per year or for low load and
maximum 316.800 switching cycles per year. GEFAHR
GEFÄHRLICHE SPANNUNG
• If the current load is known, use the diagram for the electrical service
life (see page 9/12) to calculate the maximum number of switching Die Montage, Inbetriebnahme, Änderung und Nachrüstung darf nur von
cycles. The specified performance level can only be assured for einer Elektrofachkraft ausgeführt werden!
the number of switching cycles calculated using this method. Schalten Sie das Gerät/ die Anlage vor Beginn der Arbeiten
The device must be replaced on reaching this maximum figure. spannungsfrei!
Thereby the lifetime of the device must not be exceeded.
Bei Installations und Anlagenfehlern kann bei nicht galvanisch
• Operating the device not within the specifications may lead to getrennten Geräten auf dem Steuerkreis Netzpotential anliegen!
malfunctions or the destruction of the device.
Beachten Sie für die Installation der Geräte die Sicherheitsvorschriften
• The supply input A1 serves as a control input. This may lead to short der Elektrotechnik und der Berufsgenossenschaft.
disruptions or a lowering below the operating voltage UB in order to
switch to the release path. Durch Öffnen des Gehäuses oder sonstige Manipulation erlischt
jegliche Gewährleistung.
• Expansion devices or external contactors with positively driven
contacts can be used to duplicate the enabling current paths. Die Nichtbeachtung dieser Anweisung wird Tod oder schwere
Körperverletzung zur Folge haben.
• The emergency stop chain must be closed before the reset button is
activated.
• If magnetic switches with reed contacts or sensors with
semiconductor outputs are connected the switch ON peak current
VORSICHT
must be noticed (see Technical Data). UNSACHGEMÄSSER GEBRAUCH
• Please consult the installation notes. Bei unsachgemäßen Gebrauch oder nicht bestimmungsgemäßer
Verwendung darf das Gerät nicht mehr verwendet werden und es
erlischt jeglicher Gewährleistungsanspruch.
Note: Nicht zulässige Einwirkungen können sein:
Please observe instructions from safety authorities. starke mechanische Belastung des Gerätes, wie sie z.B. beim
Herunterfallen auftritt, Spannungen, Ströme, Temperaturen,
Feuchtigkeit außerhalb der Spezifikation.
Note: Bitte überprüfen Sie gemäß der geltenden Vorschriften bei
There are no user serviceable components in the module. For safety Erstinbetriebnahme Ihrer Maschine/ Anlage immer alle
circuits according to EN / IEC 60204-1, EN ISO / ISO 13850 safety Sicherheitsfunktionen und beachten Sie die vorgegebenen Prüfzyklen
devices must use only the hard contact outputs between terminals für Sicherheitseinrichtungen.
13-14, 23-24 and 33-34. Die Nichtbeachtung dieser Anweisung kann Körperverletzung
oder Materialschäden zur Folge haben.
CAUTION
RESIDUAL RISK (EN ISO / ISO 12100-1) VORSICHT
The following wiring diagrams have been tested under actual service GEFAHR BEI INSTALLATION
conditions. This module must be used for safety-related functions in Führen Sie vor Beginn der Installation/ Montage oder Demontage
conjunction with the connected safety equipment and devices that meet folgende Sicherheitsmaßnahmen durch:
applicable standard requirements. A residual risk will remain if:
1. Schalten Sie das Gerät/ die Anlage vor Beginn der Arbeiten
a) it is necessary to modify this recommended circuit and if the added/ spannungsfrei!
modified components are not properly integrated in the control
circuit. 2. Sichern Sie die Maschine/ Anlage gegen Wiedereinschalten!
b) the user does not follow the required standards applicable to the 3. Stellen Sie die Spannungsfreiheit fest!
operation of the machine, or if the adjustments to and maintenance 4. Erden Sie die Phasen und schließen Sie diese kurz!
of the machine are not properly made. It is essential to strictly follow 5. Decken und schranken Sie benachbarte, unter Spannung stehende
the prescribed machine maintenance schedule. Teile ab!
c) the devices connected to the safety outputs do not have 6. Der Einbau der Geräte muss in einem Schaltschrank mit einer
mechanically-linked contacts. Schutzart von mindestens IP 54 erfolgen.
Failure to follow this instruction can result in injury or equipment Die Nichtbeachtung dieser Anweisung kann Körperverletzung
damage. oder Materialschäden zur Folge haben.
4 / 12
XPS-AF / Series B
VORSICHT Hinweis:
• Der Performance-Level sowie die Sicherheits-Kategorie nach
EINGESCHRÄNKTER BERÜHRUNGSSCHUTZ EN ISO / ISO 13849-1 hängt von der Außenbeschaltung,dem
• Schutzart nach EN/IEC 60529. Einsatzfall, der Wahl der Befehlsgeber und deren örtlicher
Anordnung an der Maschine ab.
• Gehäuse/Klemmen: IP 40 / IP 20.
• Der Anwender muss eine Risikobeurteilung nach EN ISO /
• Fingersicher nach EN 50274. ISO 14121-1 durchführen.
Die Nichtbeachtung dieser Anweisung kann Körperverletzung • Auf dieser Basis muss eine Validierung der Gesamtanlage /
oder Materialschäden zur Folge haben. -maschine nach den einschlägigen Normen durchgeführt werden.
• Das Modul enthält elektromechanische Relais und somit ist sein
angegebener Performance-Level und sein MTTFd Wert abhängig
Anwendungsbereich von der Last und der Schalthäufigkeit im Anwendungsfall. Bei
Das Gerät XPS-AF dient dem sicherheitsgerichteten Unterbrechen Nennlast und maximal 6.336 Schaltungen pro Jahr oder bei geringer
eines oder mehrerer Stromkreise(s) und ist für folgende Anwendungen Last und maximal 316.800 Schaltungen pro Jahr ergeben sich die
bestimmt: obigen Werte für den Performance- Level und den MTTFd.
• Manueller oder automatischer Start • Bei bekannter Strombelastung ist das Diagramm für die elektrische
• 3 Freigabestrompfade, 1 Meldestrompfad Lebensdauer (siehe Seite 9/12) für die Berechnung der maximalen
Schaltspiele heranzuziehen. Der angegebene Performance-Level
• Rückführkreis zur Überwachung externer Schütze
ist nur für diese zu ermittelnden Schaltspiele gewährleistet.
Überwachungsbaustein für Not-Halt Kreise Nach Erreichen dieser Schaltspiele ist das Gerät
• Überwachungsbaustein nach EN / IEC 60204-1 und EN ISO / auszutauschen. Die Lebensdauer des Gerätes darf dabei nicht
ISO 13850 überschritten werden.
für Not - Halt - Überwachung • Das Betreiben des Gerätes außerhalb der Spezifikation kann zu
• Für Stop-Kategorie 0 gemäß EN / IEC 60204-1: Funktionsstörungen oder zur Zerstörung des Gerätes führen.
- PL e / Kategorie 4 • Der Eingang A1 ist der Steuereingang, deshalb können kurze
- MTTFd = 243 Jahre Unterbrechungen oder eine Absenkung unterhalb von UB zum
- PFHd = 4,62 x 10-9 1/h Schalten der Freigabepfade führen.
- SILCL 3
• Zur Vervielfältigung der Freigabestrompfade können
• Überwachung von Positionsschaltern an trennenden Erweiterungsgeräte oder externe Schütze mit zwangsgeführten
Schutzeinrichtungen. Kontakten eingesetzt werden.
Das Gerät ist für einkanalige und zweikanalige Eingangsbeschaltung • Bevor der Reset-Taster aktiviert wird, muss die Not-Halt-Kette
geeignet. Aufgrund der erweiterten Fehlerdetektionsmöglichkeiten und geschlossen sein.
des daraus resultierenden höheren Sicherheitsniveaus wird die
zweikanalige Eingangsbeschaltung empfohlen. In dieser Betriebsart • Beim Anschluss von Magnetschaltern mit Reedkontakten oder
werden ebenfalls die Anschlußleitungen in die Überwachung Sensoren mit Halbleiter-Ausgängen muss der Einschaltspitzenstrom
einbezogen. beachtet werden (siehe Technische Daten).
Die den jeweiligen Überwachungsfunktionen zugeordneten • Beachten Sie die Installationshinweise.
Anschlußbilder und Funktionsdiagramme sind den Seiten 6/12 - 8/12 zu
entnehmen.
Hinweis:
Eine eingebaute elektronische Sicherung schützt das Gerät XPS-AF vor
Zerstörung durch äußere Kurzschlüsse (z.B. bei Querschlüssen in der Bitte beachten Sie auch die Informationen Ihrer Berufsgenossenschaft!
Eingangsbeschaltung). Nach Beseitigung der Fehlerursache ist der
Baustein nach einigen Sekunden wieder betriebsbereit.
Hinweis:
Bestimmungsgemäße Verwendung
Das Gerät enthält keine vom Anwender zu wartenden Bauteile. Zur
Das Gerät dient der Überwachung von Signalgebern z.B. Not-Halt-
Freigabe eines Sicherheitsstromkreises gemäß EN / IEC 60204-1,
Tastern, Positionsschaltern, welche als Teil von Schutzeinrichtungen an
EN ISO / ISO 13850 sind ausschließlich die potentialfreien
Maschinen zum Zweck des Personen-, Material- und
Ausgangskreise zwischen den Klemmen 13-14, 23-24 und 33-34 zu
Maschinenschutzes eingesetzt werden.
verwenden.
VORSICHT
RESTRISIKEN (EN ISO / ISO 12100-1)
Der nachstehende Schaltungsvorschlag wurde mit größter Sorgfalt
unter Betriebsbedingungen geprüft und getestet. Er erfüllt mit der
angeschlossenen Peripherie sicherheitsgerichteter Einrichtungen und
Schaltgeräte insgesamt die einschlägigen Normen. Restrisiken
verbleiben wenn:
a) vom vorgeschlagenen Schaltungskonzept abgewichen wird und
dadurch die angeschlossenen sicherheitsrelevanten Geräte oder
Schutzeinrichtungen möglicherweise nicht oder nur unzureichend in
die Sicherheitsschaltung einbezogen werden.
b) vom Betreiber die einschlägigen Sicherheitsvorschriften für Betrieb,
Einstellung und Wartung der Maschine nicht eingehalten werden.
Hier sollte auf strenge Einhaltung der Intervalle zur Prüfung und
Wartung der Maschine geachtet werden.
Die Nichtbeachtung dieser Anweisung kann Körperverletzung
oder Materialschäden zur Folge haben.
5 / 12
XPS-AF / Series B
Schéma de raccordement pour le module XPS-AF
Wiring diagram for module XPS-AF
Anschlußschema für XPS-AF
L(+) F1 (1) =
Avec surveillance du bouton de démarrage
24V (3)
With monitoring of the start button
Mit Starttasterüberwachung
K3
S2 F2 F3 (2) =
(3) (3) Sans surveillance du bouton de démarrage
K4 Marche Without monitoring of the start button
Start Ohne Starttasterüberwachung
Start
(1) (2)
ESC
T K1 K3 K3 K3
XPS-AF LOGIC
K2 K4 K4 K4
S1 K3 K4
Arrêt
d'urgence (3) =
Emergency Voir caractéristiques techniques pour
Stop
Not-Halt le calibre maximal des fusibles
N(–) See Technical Data for maximum fuse sizes
3 sorties de sécurité, libres de potentiel Siehe technische Daten für max. Sicherung.
3 floating safety outputs
3 potentialfreie Sicherheitsausgänge
ESC =
Conditions externes de démarrage
External start conditions
Externe Start Bedingungen
DANGER
Raccordement
Raccordement dudubouton
boutonà àune
unevoie
voie, Catégorie 1
One channel connection
One channel connectionofofone
oneemergency
emergency stop
stop button, Category 1
button
Tasteranschluß einkanalig, Kategorie 1 HAZARDOUS VOLTAGE
Tasteranschluß einkanalig
Disconnect all power before working on equipment.
S1 Arrêt d'urgence Failure to follow this instruction will result in death or serious
Arrêt d'urgencestop
Emergency injury.
Emergency stop
Not-Halt
NOT-AUS
A1
Raccordement
Raccordementde deplusieurs
plusieursboutons
boutonsarrêt d'urgence
arrêt d'urgence, Catégorie 3
Connectionofofseveral
Connection several emergency
emergency stop
stop buttons, Category 3
buttons
A2 S11 S12 S21 S22 Anschlußmehrerer
mehrererNOT-AUS
Not-Halt Taster
Taster, Kategorie 3
Anschluß
6 / 12
XPS-AF / Series B
Schéma de raccordement pour le module XPS-AF
Wiring diagram for module XPS-AF
Anschlußschema für XPS-AF
Surveillance d'interrupteurs de position, avec détection des courts-circuits, Sans bouton de démarrage (démarrage automatique)
Surveillance
Catégorie 4 d'interrupteurs de position Without start button (automatic start)
Limit switch monitoring
Limit switch monitoring, with short circuit detection, Category 4
Positionsschalterüberwachung,
Ohne Start-Taster (automatischer Start)
Positionsschalterüberwachung mit Querschlusserkennung, Kategorie 4
Input A Input B
Protecteur (fermé)
Protective guard (closed) S2 Marche
Schutzgitter (geschlossen) Start
Start
Ouvrir le protecteur
Open the protective guard A1 S33 S34 S39 13 23 33
Schutzgitter öffnen
S2 Marche
Start
Start
1 A1/A2 - Fuse
7 / 12
XPS-AF / Series B
Diagrammes fonctionnels du XPS-AF
Functional diagrams XPS-AF
Funktionsdiagramme XPS-AF
Fonction
Fonction arrêt
arrêt d'urgence
d'urgence
Emergency
Emergency stop
stop function
function
Not-Aus Funktion
Not-Halt Funktion
TensionTension
d'alimentation
d'alimentation Marche Arrêt d'urgence non actionné
Marche Arrêt d'urgence actionné
Supply
Supply voltage
voltage Arrêt d'urgence
Start Emergency
Start nonactuated
stop not actionné Arrêt d'urgence
Emergency stopactionné
actuated
Spannung
SpannungEin Ein Start Not-
Start Halt unbetätigt
Emergency stop not actuated Not- Halt betätigt
Emergency stop actuated
NOT-AUS unbetätigt NOT-AUS betätigt
Entrée A (S11-S12)
Input A (S11-S12)
Eingang A (S11-S12)
Entrée B (S21-S22)
Input B (S21-S22)
Eingang B (S21-S22) ➀ Avec surveillance du bouton
Bouton de démarrage S33-S34 (F)
Start button S33-S34 (NO)
➀ de démarrage
With start button monitoring
Start-Taster S33-S34 (S) Mit Start-Tasterüberwachung
Bouton de démarrage S33-S39 (F) ➁
Start button S33-S39 (NO)
Start-Taster S33-S39 (S) ➁ Sans surveillance du bouton
de démarrage
Sortie 13-14 (F) Without start button monitoring
Output 13-14 (NO) Ohne Start-Tasterüberwachung
Ausgang 13-14 (S)
Sortie 23-24 (F)
Output 23-24 (NO)
Ausgang 23-24 (S)
Sortie 33-34 (F)
Output 33-34 (NO)
Ausgang 33-34 (S)
8 / 12
XPS-AF / Series B
Durée de vie électrique des contacts de sortie selon EN / IEC 60947-5-1 / Annexe C.3
Electrical life of the output contacts determined by EN / IEC 60947-5-1 / Annex C.3
Elektrische Lebensdauer der Ausgangskontakte gemäß EN / IEC 60947-5-1 / Anhang C.3
100
DC13: 24V
Schaltstrom x 0,1 A
10
1
104 105 106 107
Cycles de
Cycles de manoeuvre manoeuvre
/ Operation Cycles / Schaltspiele
Operation Cycles
- Données sur les bornes et les connexions - Terminals and connection - Klemmen- und Anschlussdaten
XPS-AF.... XPS-AF.... XPS-AF....
Connection un fil Single wire connection Einzelleiteranschluß
Sans embout: Without cable end: Ohne Aderendhülse:
rigide 0,14-2,5 mm2 solid 0.14-2.5 mm2 starr 0,14-2,5 mm2
flexible 0,14-2,5 mm2 stranded 0.14-2.5 mm2 flexibel 0,14-2,5 mm2
Longueur de dénudage: 7 mm AWG 26-14 Abisolierlänge: 7 mm
Flexible avec embout Stripping length: 7 mm (0.28 in.) Flexibel mit Aderendhülse
(sans colleret plastique): 0,25-2,5 mm2 Flexible with cable end (ohne Kunststoffhülse): 0,25-2,5 mm2
(avec colleret plastique): 0,25-1,5 mm2 (without plastic sleeve): 0.25-2.5 mm2 (mit Kunststoffhülse): 0,25-1,5 mm2
Couple de rotation min.: 0,5 Nm (24-14 AWG1)) Anzugsdrehmoment min.: 0,5 Nm
(with plastic sleeve): 0.25-1.5 mm2
Connection deux fils (24-16 AWG1)) Mehrleiteranschluß (2 Leiter max.)
Sans embout: Tightening torque, min.: 0,5 Nm (4.4 lb-in) Ohne Aderendhülse:
rigide 0,14-0,75 mm2 starr 0,14-0,75 mm2
flexible 0,14-0,75 mm2 Multiple-wire connection (2 wires max.) flexibel 0,14-0,75 mm2
Longueur de dénudage: 7 mm Without cable end: Abisolierlänge: 7 mm
solid 0.14-0.75 mm2
Flexible avec embout (26-20 AWG1)) Flexibel mit Aderendhülse
(sans colleret plastique): 0,25-1 mm2 stranded 0.14-0.75 mm2 (ohne Kunststoffhülse): 0,25-1 mm2
Flexible avec embout TWIN (26-20 AWG1)) Flexibel mit TWIN-Aderendhülse
(avec colleret plastique): 0,5-1,5 mm2 Stripping length: 7 mm (0.28 in.) (mit Kunststoffhülse): 0,5-1,5 mm2
Couple de rotation min.: 0,5 Nm Flexible with cable end Anzugsdrehmoment min.: 0,5 Nm
(without plastic sleeve): 0.25-1 mm2
(24-18 AWG1))
XPS-AF....P XPS-AF....P
Flexible with TWIN-cable end
Connection un fil (with plastic sleeve): 0.5-1.5 mm2 Einzelleiteranschluß
Sans embout: (22-14 AWG1)) Ohne Aderendhülse:
rigide 0,2-2,5 mm2 starr 0,2-2,5 mm2
Tightening torque, min.: 0,5 Nm (4.4 lb-in)
flexible 0,2-2,5 mm2 flexibel 0,2-2,5 mm2
Longueur de dénudage: 7 mm Abisolierlänge: 7 mm
XPS-AF....P
Flexible avec embout Flexibel mit Aderendhülse
(sans colleret plastique): 0,25-2,5 mm2 Single wire connection (ohne Kunststoffhülse): 0,25-2,5 mm2
(avec colleret plastique): 0,25-1,5 mm2 Without cable end: (mit Kunststoffhülse): 0,25-1,5 mm2
Couple de rotation min.: 0,5 Nm solid 0.2-2.5 mm2 Anzugsdrehmoment min.: 0,5 Nm
stranded 0.2-2.5 mm2
Connection deux fils Mehrleiteranschluß (2 Leiter max.)
AWG 24-12
Sans embout: Stripping length: 7 mm (0.28 in.) Ohne Aderendhülse:
rigide 0,2-1 mm2 starr 0,2-1 mm2
flexible 0,2-1,5 mm2 Flexible with cable end flexibel 0,2-1,5 mm2
(without plastic sleeve):
Longueur de dénudage: 7 mm Abisolierlänge: 7 mm
0.25-2.5 mm2 (22-14 AWG1))
Flexible avec embout (with plastic sleeve): Flexibel mit Aderendhülse
(sans colleret plastique): 0,25-1 mm2 0.25-1.5 mm2 (22-16 AWG1)) (ohne Kunststoffhülse): 0,25-1 mm2
Flexible avec embout TWIN Tightening torque, min.: 0,5 Nm (4.4 lb-in) Flexibel mit TWIN-Aderendhülse
(avec colleret plastique): 0,5-1,5 mm2 (mit Kunststoffhülse): 0,5-1,5 mm2
Couple de rotation min.: 0,5 Nm Anzugsdrehmoment min.: 0,5 Nm
9 / 12
XPS-AF / Series B
- Fixation du boîtier: Multiple-wire connection (2 wires max.) - Gehäusebefestigung:
Encliquetage sur profilé chapeau 35 mm Without cable end: Schnappbefestigung auf 35 mm
selon EN/IEC 60715 solid 0.2-1 mm2 (24-18 AWG1)) Normschiene nach EN/IEC 60715
- Degré de protection selon EN/IEC 60529: stranded 0.2-1.5 mm2 (24-16 AWG1)) - Schutzart gemäß EN/IEC 60529:
Bornes: IP20 Stripping length: 7 mm (0.28 in.) Klemmen: IP20
Boîtier: IP40 Gehäuse: IP40
Flexible with cable end
- Poids: 0,25 kg (without plastic sleeve): - Gewicht: 0,25 kg
- Position de montage: indifférente 0.25-1 mm2 (22-18 AWG1)) - Einbaulage: beliebig
- Température de fonctionnement: Flexible with TWIN-cable end - Umgebungstemperatur im Betrieb:
-25°C / +55°C (with plastic sleeve): -25°C / +55°C
- Catégorie de surtension III (4 kV) 0.5-1.5 mm2 (20-16 AWG1)) - Überspannungskategorie III (4 kV)
Degré de pollution 2 Tightening torque, min.: 0,5 Nm (4.4 lb-in) Verschmutzungsgrad 2
Tension assignée d’isolement 300Va 1) AWG indication according to Bemessungsisolationsspannung 300Va
selon EN/IEC 60664-1 EN/IEC 60947-1 / table 1 gemäß EN/IEC 60664-1
- Tension d’alimentation UE selon IEC 60038: - Anschlußspannung UE gemäß IEC 60038:
24V z (+10% / -15%) 24V z (+10% / -15%)
- Mounting:
(voir plaque signalétique) (Siehe Typenschild)
Mounting on 35 mm DIN rail
Protection max.: 4 A gL Absicherung max.: 4 A gL
according to EN/IEC 60715
- Puissance consommée: - Eigenverbrauch:
- Degree of protection according to
Version 24V z ≤ 5 VA Version 24V z ≤ 5 VA
EN/IEC 60529:
- Sorties de sécurité (libre de potentiel): Terminals: IP20 - Sicherheitsausgänge (potentialfrei):
13 - 14, 23 - 24, 33-34 Enclosure: IP40 13 - 14, 23 - 24, 33-34
- Capacité de coupure maxi des sorties: - Weight: 0.25 kg (8.8 oz) - Max. Schaltleistung der Ausgangskanäle:
AC-15: Ue = 240Va / le = 0.75A AC-15: Ue = 240Va / le = 0.75A
- Mounting position: Any plane
DC-13: Ue = 24Vc / le =1.5A DC-13: Ue = 24Vc / le =1.5A
- Ambient operating temperature:
- Durée de vie mécanique (Commutations): - Mechanische Lebensdauer (Schaltungen):
-25°C to +55°C (-13°F to +130°F)
10 * 106 10 *106
- Overvoltage category III (4 kV)
- Limite des courants cumulés (charge - Summenstrombegrenzung bei gleichzeitiger
Pollution degree 2
simultanée des plusieurs circuits de sortie): Belastung mehrerer Ausgangskreise:
Rated insulation voltage: 300Va
Σ Ith ≤ 18 A Σ Ith ≤ 18 A.
according to EN/IEC 60664-1
- Supply voltage UE according to IEC 60038:
24V z (+10% / -15%) 6A 6A 6A
6A 6A 6A
(Refer to device nameplate for supply
- Protection des sorties: - Absicherung der Ausgangskreise:
voltage)
(max.: 4 A gL ou 6A rapide max.: 4 A gL oder 6A Flink
Max. protection: 4 A fuse (gL)
- Temps de réponse, - Ansprechzeit,
- Power consumption:
≤ 20ms S11-S12, S21-S22: ≤ 20ms
S11-S12, S21-S22: Version 24V z ≤ 5 VA
A1 ou A2: ≤ 60ms A1 ou A2: ≤ 60ms
- Safety outputs:
- Temps de synchronisation entre entrée A et - Synchronisationszeit zwischen Input A und
13 - 14, 23 - 24, 33-34
entrée B à l'utilisation sans bouton de Input B bei Verwendung ohne Starttaster:
démarrage: t=∞ - Maximum switching capacity of outputs: t=∞
AC-15: Ue = 240Va / le = 0.75A Das Gerät ist ebenfalls zum Schalten von
L'appareil est aussi capable de commuter des DC-13: Ue = 24Vc / le =1.5A
charges faibles (17Vc / 10 mA minimum), à Kleinstlasten (min. 17Vc / 10 mA) geeignet.
- Mechanical service life (Switching Dies ist jedoch nur dann möglich, wenn bisher
condition que le contact n'ait jamais commuté
operations): 10 * 106 über diesen Kontakt keine höheren Lasten
de forte charge auparavant, car la couche d'or
revêtant le contact pourrait être altérée. - The sum of simultaneous currents on all of geschaltet wurden, da hierdurch die
the outputs is limited to : Kontaktvergoldung abgebrannt sein könnte.
- Résistivité dans l'alimentation des
Σ Ith ≤ 18 A. - Leitungswiderstand in der Spannungs-
actionneurs: max. 90 Ω
versorgung der Befehlsgeber: max. 90 Ω
6A 6A 6A
- Protections of outputs:
max.: 4 A fuse (gL) or 6A fastblow
- Response time,
S11-S12, S21-S22: ≤ 20ms
A1 ou A2: ≤ 60ms
- Synchronisation time between Input A and
Input B without use of start button (automatic
start): t=∞
Minimum switching ratings of outputs:
The device is capable to switch the low voltage
loads (min. 17Vc / 10 mA) provided that the
contact has never been used with higher loads.
- Resistance in the voltage supply to the
sensors: max. 90 Ω
10 / 12
XPS-AF / Series B
L'organisme agréé suivant a établi une déclaration positive selon le The following notified body has made a positive declaration in accordance to Folgende benannte Stelle hat eine positive Erklärung im Sinne des
Chapitre 7, phrase 2, 2004/108/EG: Chapter 7, Sentence 2, 2004/108/EG: Artikels 7, Satz 2, 2004/108/EG ausgestellt:
RÉFÉRENCE DE RÉFÉRENCE NOM, ADRESSE: NUMBER OF THE NUMBER OF NAME, ADDRESS: KENNNUMMER DER NUMMER DER NAME, ANSCHRIFT:
L'ORGANISME AGRÉÉ: DE LA DÉCLARATION: NOTIFIED BODY: DECLARATION: BENANNTEN STELLE: ERKLÄRUNG:
0044 4420509373024-001 TÜV NORD CERT GMBH 0044 4420509373024-001 TÜV NORD CERT GMBH 0044 4420509373024-001 TÜV NORD CERT GMBH
Langemarckstr. 20 Langemarckstr. 20 Langemarckstr. 20
D-45141 Essen D-45141 Essen D-45141 Essen
Sous réserve d’installation, d’entretien et d’utilisation conformes à sa It is important that the safety component is subject to correct installation, Falls es gemäß seiner Bestimmung, den geltenden Vorschriften, Normen und
destination, à la réglementation, aux normes en vigueur, aux instructions du maintenance and use conforming to its intended purpose, to the applicable Herstelleranweisungen entsprechend installiert, verwendet und gewartet
constructeur et aux règles de l’art. regulations and standards, to the supplier’s instructions and to accepted rules wird.
of the art.
Documentation autorité: Dokumentations Bevollmächtigter:
Eric Léon Barry / Schneider Electric Automation GmbH / Documentation authority: Eric Léon Barry / Schneider Electric Automation GmbH /
Steinheimer Straße 117 / 63500 Seligenstadt, Germany Eric Léon Barry / Schneider Electric Automation GmbH / Steinheimer Straße 117 / 63500 Seligenstadt, Germany
Steinheimer Straße 117 / 63500 Seligenstadt, Germany
France - Rueil Malmaison p. p. François Mondino Frankreich - Rueil Malmaison i. V. François Mondino
17 - Septembre - 2009 OEM R&D Vice-President France - Rueil Malmaison p. p. François Mondino 17 - September - 2009 OEM R&D Vice-President
17 - September - 2009 OEM R&D Vice-President
La Déclaration CE de Conformité d'origine est disponible sur notre site Web: Die original EG-Konformitätserklärung ist auf unserer Webseite erhältlich:
www.schneider-electric.com The original EC Declaration of Conformity is available on our website: www.schneider-electric.com
www.schneider-electric.com
11 / 12
XPS-AF / Series B
Schneider Electric Industries SAS / 35, rue Joseph Monier / 92506 Rueil-Malmaison, France 12 / 12