ae
AKAT Service manuat
MODEL AM-27
STEREO INTEGRATED AMPLIFIER
move. AM-17
move. AM-27
SPECIFICATIONS
Power output (OIN) 7 Wratio (HFA)
‘AMAT 35W + 35W (@ ohms, tkH2 1%) | Phono (MM) aus 700
aM-27 GOW + B0W (Bonms,tkHe.1%) | Others 9008
Total harmonic eistoron.. 0.05% Crosstalk
Frequency response... 20 He to 20 kHe (0.5 dB) Phono 6048 (IkHz, 5.0 mV input evel
Tone control co 60 dB (1kH2, SOOM input evel)
Bass £10 68 (100 He) Required speaker impedance
Trebie 10-08 (10 KH2), ‘Aor "Bo 16 ohms
Loudness (AM27 only)» 6.68 (100 Hz) 448 (HO kH2) | and Bovvsnsns-s B10 16 08ms
Input sensitivity / impedance | Power requirement’. AC220 V to 290 V, SOH2 for
Phono (MM) nnunsnn 25 mV / 47 k ohms | Europe excopt UK
Others 450m) 47 k ohms | {AC240 V, 50 Ha for UK and
Maximum input level | Australia| |
Phono toomv Dimensions ssnsnnnn 425 QH) x135 (H) x 285 (0) mm
others 60v Weight |
Output evel |" aMa7 64 ko
Tape REC oUt oon» 150m aw27 eaKg
‘Damping factor 27 (50 Hz, 8 ohms) ,_ Satepenenenes|
| Residal noise O5mv Standerd accessories
|__ Operators manual 1
“ For improvement purposes, specifications and design are subject to change without notice,* SAFETY INSTRUCTIONS
PRECAUTIONS DURING SERVICING
1. Parts indented by the 1 (#) symbol are cortical for
safety. Replace only with parts number specified.
2. In addition to safety, other parts and assemblies are
‘specified for conformance with such regulations as those
‘applying to spurious radiation.
These must also be replaced only with speciied re-
placements.
Examples: RF converters, tuner units, antenna selector
switches, AF cables, noise blocking capacitors, noise
blocking filters, et.
8. Use specified internal wiring, Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
4, Use spectied insulating materials for hazardous live
parts, Note especially:
41) Insulation Tape
2) PVC tubing
3) Spacers (Insulating barriers)
4) Insulation sheets for transistors
5) Plastic screws for fixing microswitch (especially in
turntable)
5. When replacing AC primary side components (trans:
formers, power cords, noise blocking capacitors, etc.)
wrap ends of wires securely about the terminals before
soldering
poke
6. Observe that wires do not contact heat producing parts
(heatsinks, oxide metal fm resistors, fusible resistors,
etc)
* INFORMATION
7. Check that replaced wires do not contact sharp edged
oF pointed pars.
8. Also check areas surrounding repaired locations.
9, Use care that foreign objects (screws, solder droplets,
etc.) do not remain inside the set.
SAFETY CHECK AFTER SERVICING
Ater servicing, make measurements of leakage-current or
resistance in order to determine that exposed parts are
acceptably insulated from the supply citcutt.
The leakage-current measurement should be done be.
tween accessible metal parts (such as chassis, ground
terminal, microphone jacks, signal inpuvloutput connec:
tors, ete.) and the earth ground through a resister of 1500
ohms paralleled with a 0.15 uF capacitor, under the unit's
normal working conditions. The leakage-curent should be
less than 0.5 mA rms AC.
The resistance measurement should be done between
accessible exposed metal parts and power cord plug prongs
with the power switch (if included) "ON". The resistance
should be more than 2.2 Mohms.
SYMBOLS FOR PRIMARY DESTINATION
Alphabet indicates the destination of the units as listed
below.
———
bs Pring
‘Symbols i Destinations
a
Europe (except UK)
s ‘Australia
S| Germany = 7
[U —[-Unwversal Area
(WT [ Custom version ——
SERVICE MANUAL|. DISASSEMBLY
In case of trouble. etc. necessitating dismanting, please dismantle in the order shown in the illustrations
Reassemble in reverse order
1 Removal of the UPPER COVER 2. Removal of the FRONT PANEL BLOCK
fi UPPER COVER
I. PRINCIPAL PARTS LOCATION
SPEAKER TERMINAL PCB MAIN PCB.
SS
|
|
ULC
[rss = 1
POWER SW PCB POWER TRANSFORMER VOLUME PCB TONE CONTROL PCB
Fig. 2-4 Top view