You are on page 1of 9
raisro%e ‘TS LTE | Sunil Bhargav - Academia.edu TS LTE ‘Sunil Bhargav 18118 G or download with emai ERICSSON Z Ericsson Internal DOCUMENT LIST Pred Spe) os Lilia Yvette Leon. Uen Rowers Decne a) Toes oa TR Fae 2012-07-16 PAT READ PAPER Trouhleshootina Parameter Chanae htphwww academia. edu/29698964/TS, LTE 19 raisro%e hp academia edu20598364/TS_LTE ‘TS LTE | Sunil Bhargav - Academia.edu Objective. Parameter Change.. 2.1 Non Service Impacting 2.2 Service Impacting Precheck before Trouble shootin: Troubleshooting Most common EnodeB Alanm: 4.1 Disk Volume... 42 ResourceAllocationFailure EUtranCellF OL frequency:.... out of band). 4.3. Remote IP Address Unreachable. 44 InconsistentConfiguration AntennaUnitGroup=...,Anten =...,RetSubUnit= (Tilt value out of range)... 4.5 ExternalAlarm AuxPluginUnit=RRU..., DeviceGroup=ruAlarmPort=... (RBS LTE RRU SQUID (Carrie 48 HUD FaUbuHeSs Sie rela Shar are war Ranch onal, A” 47 LinkFailure Subrack=...,Slot=....PlugInUnit=..., RiPort=C signal detected, port 4, cascadeNo 0, ruPortNo 0) 4.8 _ InconsistentConfiguration Sector quipmentFunction=. power limited by RU capabilities)... 4.9 __ InconsistentConfiguration ‘SectorEquipmentFunct (Output power limited by license OMF_LICENSE_CAPACITY_OUTPUT_POWER). 4410 NoContact AntennaUnitGroup=3,AntennaNearUnit=1 (Timeout: Fa anuComnectindication)...... 4.11 ServiceUnavailable EUtranCellF DD: PLMN mec:310 mne:410 duld: 1) (S1 Connector 29 raisro%e ‘TS LTE | Sunil Bhargav - Academia.edu DOCUMENT LIST Lilia Yvette Leon Uen Towrered Deca a) Tear a Tie Taare 2012-07-16 PAT 24 22 htp:nwww academia edu20598364/TS_LTE Objective This document is a guide to perform troubleshooting for LTE EnodeB alarms. Parameter Change Change Parameters in eNodeB is performed for post- optimization improvement or prior Launch activities to optimize network performance. the Region and the market are the values to be set. Temporary service interruption while performing the activity / change. This can be performed with written approval from customer. The activity is divided into different Stages (After performing respective Pre-c + Non Service Impacting (eNodeB PC) * Service Impacting (eNodeB PC) Non Service Impacting In this part of the Activity parameters that don't affect directly the netw in the eNodeB. Scripts included in the MOP must be followed depen: Region to perform corresponding Prechecks & Postchecks Service Impacting In this part of the Activity, parameters that affect directly the network ar eNodeB, Sites must be LOCKED before setting the parameters, maki previous state of every eutrancell is saved in order to retum to that s after the parameters are set. Scripts included in the MOP must E depending on the Region to perform corresponding activity NOTE: For further information regarding Parameter Change please corresponding MOP (Pre-Launch sites / Post-Launch sites) Ee] Method of Procedure Method of Procedure = ATET eNedeB Paral- ATST eNodeB Paran Precheck before Trouble shooting Before performing troubleshooting check the basic parameters. Don't forg a log. 39

You might also like