You are on page 1of 41

"JOIST" --- STEEL JOIST ANALYSIS

Program Description:

"JOIST" is a spreadsheet program written in MS-Excel for the purpose of analysis of steel joists considered as
simple-span beams subjected to virtually any type of loading configuration. Specifically, beam end reactions as well
as the maximum moments and deflections are calculated. Plots of both the shear and moment diagrams are
produced, as well as a tabulation of the shear, moment, slope, and deflection for the joist span. There are two
worksheets for selecting K-series and LH-series joists, and 2 worksheets which are the SJI Standard Load Tables.

This program is a workbook consisting of eight (8) worksheets, described as follows:

Worksheet Name Description


Doc This documentation sheet
General Joist Analysis General standard joist analysis for steel joists for non-standard loads
K-Joist Analysis Analysis for typical, standard loaded, open-web K-series steel joists
K-Joist Table Standard (SJI) load table for open-web K-series steel joists
KCS-Joist Analysis Analysis for non-standard loaded, open-web KCS-series steel joists
KCS-Joist Table Load table for open-web KCS-series steel joists
LH-Joist Analysis Analysis for typical, standard loaded, longspan LH-series steel joists
LH-Joist Table Standard (SJI) load table for longspan LH-series steel joists

Program Assumptions and Limitations:

1. For the "General Joist Analysis" worksheet, the following reference was used in the development of this program:
"Modern Formulas for Statics and Dynamics, A Stress-and-Strain Approach"
by Walter D. Pilkey and Pin Yu Chang, McGraw-Hill Book Company (1978), pages 11 to 21.
2. The "General Joist Analysis" worksheet on the joist span will handle a full length uniform load and up to eight (8)
partial uniform, triangular, or trapezoidal loads, up to fifteen (15) point loads, and up to four (4) applied moments.
3. The "General Joist Analysis" worksheet will calculate the joist end vertical reactions, the maximum positive
moment and negative moment (if applicable), and the maximum negative deflection and positive deflection (if
applicable). The calculated values for the end reactions and maximum moments and deflections are determined
from dividing the joist into fifty (50) equal segments with fifty-one (51) points, and including all of the point load
and applied moment locations as well. (Note: the actual point of maximum moment occurs where the shear = 0,
or passes through zero, while the actual point of maximum deflection is where the slope = 0.)
4. In the "General Joist Analysis" worksheet the user is given the ability to input two (2) specific locations from the
left end of the joist to calculate the shear, moment, slope, deflection, as well as the stress ratios for shear and
moment. This should be utilized when the maximum moment does not occur at the start or end of a segment.
5. In the "General Joist Analysis" worksheet, the plots of the shear and moment diagrams as well as the displayed
tabulation of shear, moment, slope, and deflection are based on the joist span being divided up into fifty (50)
equal segments with-one (51) points.
6. The "General Joist Analysis" worksheet will enable the user to either analyze an existing joist for new loads or
determine the required total equivalent uniform load to be used to size a new joist.
7. The "General Joist Analysis" worksheet only analyzes the joist "as a whole" and does not perform checks on the
individual components.
8. In the "General Joist Analysis" worksheet, the deflections calculated include a 15% increase above the values
calculated using traditional "simple-beam" flexure to more closely match actual test results obtained by SJI.
9. For the "K-Joist Analysis" and "LH-Joist Analysis" worksheets, the Steel Joist Institute (SJI) Standard Load Table
as well the "Recommended Code of Standard Practice for Steel Joists and Joist Girders" are used. The
Standard Load Tables are built into each of these two analysis worksheets. The two worksheets will evaluate a
user selected joist size, as well as display up to a maximum of 15 of the lightest joist sizes that are satisfactory
for the loading and deflection criteria specified by the user. The bridging requirements are also determined.
10. This program contains numerous “comment boxes” which contain a wide variety of information including
explanations of input or output items, equations used, data tables, etc. (Note: presence of a “comment box”
is denoted by a “red triangle” in the upper right-hand corner of a cell. Merely move the mouse pointer to the
desired cell to view the contents of that particular "comment box".)
Formulas Used to Determine Shear, Moment, Slope, and Deflection in Simple-Span Joists

For Uniform or Distributed Loads:

Loading functions for each uniform or distributed load evaluated at distance x = L from left end of joist:
FvL = -wb*(L-b-(L-e)) + -1/2*(we-wb)/(e-b)*((L-b)^2-(L-e)^2)+(we-wb)*(L-e)
FmL = -wb/2*((L-b)^2-(L-e)^2) + -1/6*(we-wb)/(e-b)*((L-b)^3-(L-e)^3)+(we-wb)/2*(L-e)^2
FqL = -wb/(6*E*I)*((L-b)^3-(L-e)^3) + -1/(24*E*I)*(we-wb)/(e-b)*((L-b)^4-(L-e)^4)+(we-wb)/(6*E*I)*(L-e)^3
FDL = -wb/(24*E*I)*((L-b)^4-(L-e)^4) + -1/(120*E*I)*(we-wb)/(e-b)*((L-b)^5-(L-e)^5)+(we-wb)/(24*E*I)*(L-e)^4

Loading functions for each uniform or distributed load evaluated at distance = x from left end of joist:
If x >= e:
Fvx = -wb*(x-b-(x-e)) + -1/2*(we-wb)/(e-b)*((x-b)^2-(x-e)^2)+(we-wb)*(x-e)
Fmx = -wb/2*((x-b)^2-(x-e)^2) + -1/6*(we-wb)/(e-b)*((x-b)^3-(x-e)^3)+(we-wb)/2*(x-e)^2
Fqx = -wb/(6*E*I)*((x-b)^3-(x-e)^3) + -1/(24*E*I)*(we-wb)/(e-b)*((x-b)^4-(x-e)^4)+(we-wb)/(6*E*I)*(x-e)^3
FDx = -wb/(24*E*I)*((x-b)^4-(x-e)^4) + -1/(120*E*I)*(we-wb)/(e-b)*((x-b)^5-(x-e)^5)+(we-wb)/(24*E*I)*(x-e)^4
else if x >= b:
Fvx = -wb*(x-b) + -1/2*(we-wb)/(e-b)*(x-b)^2 else: Fvx = 0
Fmx = -wb/2*(x-b)^2 + -1/6*(we-wb)/(e-b)*(x-b)^3-(x-e)^3 else: Fmx = 0
Fqx = -wb/(6*E*I)*(x-b)^3 + -1/(24*E*I)*(we-wb)/(e-b)*(x-b)^4 else: Fqx = 0
FDx = -wb/(24*E*I)*(x-b)^4 + -1/(120*E*I)*(we-wb)/(e-b)*(x-b)^5 else: FDx = 0

For Point Loads:

Loading functions for each point load evaluated at distance x = L from left end of joist:
FvL = -P
FmL = -P*(L-a)
FqL = -P*(L-a)^2/(2*E*I)
FDL = P*(L-a)^3/(6*E*I)

Loading functions for each point load evaluated at distance = x from left end of beam:
If x > a:
Fvx = -P else: Fvx = 0
Fmx = -P*(x-a) else: Fmx = 0
Fqx = -P*(x-a)^2/(2*E*I) else: Fqx = 0
FDx = P*(x-a)^3/(6*E*I) else: FDx = 0

For Applied Moments:

Loading functions for each applied moment evaluated at distance x = L from left end of joist:
FvL = 0
FmL = -M
FqL = -M*(L-c)/(E*I)
FDL = M*(L-c)^2/(2*E*I)

Loading functions for each applied moment evaluated at distance = x from left end of joist:
If x >= c:
Fvx = 0 else: Fvx = 0
Fmx = -M else: Fmx = 0
Fqx = -M*(x-c)/(E*I) else: Fqx = 0
FDx = M*(x-c)^2/(2*E*I) else: FDx = 0

(continued)
Formulas Used to Determine Shear, Moment, Slope, and Deflection (continued)

Initial summation values at left end (x = 0) for shear, moment, slope, and deflection:

Simple beam:
Vo = -1/L*S(FmL)
Mo = 0
qo = 1/L*S(FDL)+L/(6*E*I)*S(FmL)
Do = 0

Summations of shear, moment, slope, and deflection at distance = x from left end of joist:

Shear: Vx = Vo+S(Fvx)
Moment: Mx = Mo+Vo*x+S(Fmx)
Slope: qx = qo+Mo*x/(E*I)+Vo*x^2/(2*E*I)+S(Fqx)
Deflection: Dx = -(Do-qo*x-Mo*x^2/(2*E*I)-Vo*x^3/(6*E*I)+S(FDx)

Reference:
"Modern Formulas for Statics and Dynamics, A Stress-and-Strain Approach"
by Walter D. Pilkey and Pin Yu Chang, McGraw-Hill Book Company (1978)
"JOIST.xls" Program
Version 1.6

GENERAL STANDARD JOIST ANALYSIS


For Steel Joists Considered as Simple-Span Beams
Subjected to Non-Standard Loads
Job Name: Subject: Loading Functions Evaluated
Job Number: Originator: Checker: Points:
###
Input Data: c ###
e ###
Joist Data: b ###
Designation = K-series a ###
Span, L = 40.0000 ft. +P +M we
Modulus, E = 29000000 psi +wb ###
Inertia, Ix = 526.40 in.^4 +w
###
Original Design or Capacity Loads: E,I L ###
Full Uniform: RL x RR ###
w= 373 plf Nomenclature ###
Start End ###
Distributed: b (ft.) wb (plf) e (ft.) we (plf) Point Loads: a (ft.) P (lbs.) ###
#1: #1: ###
#2: #2: ###
#3: #3: ###
#4: #4: ###
#5: #5: ###
#6: #6: ###
#7: #7: ###
#8: #8: ###
#9: ###
Moments: c (ft.) M (ft-lbs) #10: ###
#1: #11: ###
#2: #12: ###
#3: #13: ###
#4: #14: ###
#15: ###
New Design Loads: ###
Full Uniform: ###
w= 180 plf ###
Start End ###
Distributed: b (ft.) wb (plf) e (ft.) we (plf) Point Loads: a (ft.) P (lbs.) ###
#1: #1: 20.0000 2000 ###
#2: #2: ###
#3: #3: ###
#4: #4: ###
#5: #5: ###
#6: #6: ###
#7: #7: ###
#8: #8: ###
#9: ###
Moments: c (ft.) M (ft-lbs) #10: ###
#1: #11: ###
#2: #12: ###
#3: #13: ###
#4: #14: ###
#15: ###

5 of 41 03/19/2019 08:34:10
"JOIST.xls" Program
Version 1.6

###

6 of 41 03/19/2019 08:34:10
"JOIST.xls" Program
Version 1.6

###
Results of Joist Analysis: User x1
User x2
Original Design or Capacity Loads: x=a1 for P1
x=a2 for P2
End Reactions: x=a3 for P3
RL = 7460.0 lbs. RR = 7460.0 lbs. x=a4 for P4
x=a5 for P5
Minimum Design Web Member Shear: x=a6 for P6
Vw(min) = 1865 lbs. (25% of maximum end reaction for K-series and LH-series joists per SJI Spec's.) x=a7 for P7
x=a8 for P8
Maximum Moments: x=a9 for P9
+Mx(max) = 74600.0 ft-lbs @x= 20.00 ft. x=a10 for P10
-Mx(max) = 0.0 ft-lbs @x= 0.00 ft. x=a11 for P11
x=a12 for P12
*Maximum Deflections: x=a13 for P13
-D(max) = -1.619 in. @x= 20.00 ft. x=a14 for P14
+D(max) = 0.000 in. @x= 0.00 ft. x=a15 for P15
D(ratio) = L/297 x=c1 for M1
*Note: deflections shown above include a 15% increase above the values calculated using traditional x=c2 for M2
"simple-beam" flexure in order to more closely match actual test results obtained by SJI. x=c3 for M3
x=c4 for M4
x for Vx=0(1)
New Design Loads: x for qx=0(1)
x for Vx=0(2)
End Reactions: x for qx=0(2)
RL = 4600.0 lbs. RR = 4600.0 lbs.

Maximum Moments: K-series


+Mx(max) = 56000.0 ft-lbs @x= 20.00 ft. H-series
-Mx(max) = 0.0 ft-lbs @x= 0.00 ft. LH-series
-M(max) =
*Maximum Deflections:
-D(max) = -1.128 in. @x= 20.00 ft. -D(max) =
+D(max) = 0.000 in. @x= 0.00 ft. +D(max) =
D(ratio) = L/425
*Note: deflections shown above include a 15% increase above the values calculated using traditional M(max) =
"simple-beam" flexure in order to more closely match actual test results obtained by SJI.

Vx=0:
Maximum Stress Ratios: ###
###
S.R. = 0.999 for Shear @ x= 15.20 ft. Interpolatin
S.R. = 0.751 for Moment @ x= 20.00 ft. ###

qx=0:
Comments: ###
###

###

Vx(n)*Vx(n
###

7 of 41 03/19/2019 08:34:10
Moment (ft-lbs.) Shear (lbs.)

-10000.0
-8000.0
-6000.0
-4000.0
-2000.0
10000.0

0.0
2000.0
4000.0
6000.0
8000.0
0.0000

-10000.0
10000.0
20000.0
30000.0
40000.0
50000.0
60000.0
70000.0
80000.0

0.0
0.0000 0.8000
0.8000 1.6000
1.6000 2.4000
2.4000 3.2000
3.2000 4.0000
4.0000 4.8000
4.8000 5.6000
5.6000 6.4000
6.4000 7.2000
7.2000 8.0000
8.0000 8.8000
8.8000 9.6000
9.6000 10.4000
10.4000 11.2000
11.2000 12.0000
12.0000 12.8000
12.8000 13.6000
13.6000 14.4000
14.4000 15.2000
15.2000 16.0000
16.0000 16.8000
16.8000 17.6000
17.6000

8 of 41
18.4000
18.4000 19.2000
19.2000 20.0000

x (ft.)
20.0000 20.8000

x (ft.)
20.8000 21.6000
21.6000 22.4000
Shear Diagram

22.4000
23.2000

Moment Diagram
23.2000
24.0000
24.0000
24.8000
24.8000
25.6000 25.6000
26.4000 26.4000
27.2000 27.2000
28.0000 28.0000
28.8000 28.8000
29.6000 29.6000
30.4000 30.4000
31.2000 31.2000
32.0000 32.0000
32.8000 32.8000
33.6000 33.6000
34.4000 34.4000
35.2000 35.2000
36.0000 36.0000
36.8000 36.8000
37.6000 37.6000
38.4000 38.4000
39.2000 39.2000
40.0000 40.0000

03/19/2019 08:34:10
Version 1.6
"JOIST.xls" Program

###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###

Vx=0:
"JOIST.xls" Program
Version 1.6

= curves for original design or capacity loads = curves for new design loads ###

9 of 41 03/19/2019 08:34:10
"JOIST.xls" Program
Version 1.6

K-SERIES JOIST ANALYSIS


For Uniformly Loaded, Open-Web Steel Joists
Using Steel Joist Institute (SJI) Standard Load Tables
Job Name: Subject: Joist Designation
Job Number: Originator: Checker: Depth (in.)
Approx. Wt. (lbs./ft.)
Input Data: Span (ft.)
Joist Designation (Size) = 24K6 +W(TL)= 250.0 ###
Joist Span, L = 36.0 ft. ###
Joist Spacing, S = 5.0000 ft. ###
Unif. Dead Load, w(DL) = 20.00 psf ###
Unif. Live Load, w(LL) = 30.00 psf E,Ix L=36 ###
Deflect. Factor, DF(LL) = 360 ###
RL=4500 RR=4500 ###
Results: Nomenclature ###
Required Loads: ###
Dead Load, W(DL) = 100.0 plf W(DL) = w(DL)*S ###
Live Load, W(LL) = 150.0 plf W(LL) = w(LL)*S ###
Total Load, W(TL) = 250.0 plf W(TL) = W(DL)+W(LL) ###
Reactions, RL & RR = 4500.0 lbs. RL = RR = W(TL)*L/2 ###
###
###
For Joist Selected ###
Joist Joist Joist Allowable Loads and Stress Ratios # Rows ###
Size Weight Inertia, Ix W(TL) Flexure W(LL) Deflect. of ###
(plf) (in.^4) (plf) Ratio (plf) Ratio Bridging ###
24K6 9.7 222.3 281 0.890 183 0.820 3 ###
###
For 15 Lightest Acceptable K-series Joist Systems ###
Joist Joist Joist Allowable Loads and Stress Ratios # Rows ###
Sizes Weight Inertia, Ix W(TL) Flexure W(LL) Deflect. of ###
(plf) (in.^4) (plf) Ratio (plf) Ratio Bridging ###
1 22K6 9.2 185.9 257 0.973 153 0.980 **3 ###
2 24K5 9.3 205.3 258 0.969 169 0.888 3 ###
3 22K7 9.7 205.3 286 0.874 169 0.888 3 ###
4 24K6 9.7 222.3 281 0.890 183 0.820 3 ###
5 26K5 9.8 241.8 280 0.893 199 0.754 3 ###
6 24K7 10.1 246.6 313 0.799 203 0.739 3 ###
7 26K6 10.6 262.4 305 0.820 216 0.694 3 ###
8 20K9 10.8 199.2 311 0.804 164 0.915 3 ###
9 26K7 10.9 291.6 340 0.735 240 0.625 3 ###
10 22K9 11.3 244.2 344 0.727 201 0.746 3 ###
11 28K6 11.4 306.1 330 0.758 252 0.595 3 ###
12 24K8 11.5 269.7 346 0.723 222 0.676 3 ###
13 18K10 11.7 187.1 330 0.758 154 0.974 2 ###
14 28K7 11.8 340.2 367 0.681 280 0.536 3 ###
15 24K9 12.0 292.8 377 0.663 241 0.622 3 ###
**(1-5) Denotes row of bridging nearest mid-span required to be diagonal bridging. ###
###
Notes: 1. OSHA is interpreting Section 29CFR-1926.751(c)2 to mean all joists whose length ###
>= 40' require bolted diagonal bridging in place before slackening of hoisting lines. ###
2. For point loads on K-series joists, the magnitude and location of load should be ###
indicated on the design drawings and "SP" must be added to the joist designation. ###
###

10 of 41 03/19/2019 08:34:11
"JOIST.xls" Program
Version 1.6

###

11 of 41 03/19/2019 08:34:11
Joist Designation 8K1 10K1 12K1 12K3 12K5 14K1 14K3 14K4 14K6 16K2 16K3 16K4 16K5 16K6 16K7 16K9 18K3 18K4 18K5 18K6 18K7 18K9 18K10
Depth (in.) 8 10 12 12 12 14 14 14 14 16 16 16 16 16 16 16 18 18 18 18 18 18 18
Approx. Wt. (plf) 5.1 5.0 5.0 5.7 7.1 5.2 6.0 6.7 7.7 5.5 6.3 7.0 7.5 8.1 8.6 10.0 6.6 7.2 7.7 8.5 9.0 10.2 11.7
Span (ft.)
550
8
550
550
9
550
550 550
10
480 550
532 550
11
377 542
444 550 550 550 550
12
288 455 550 550 550
377 479 550 550 550
13
225 363 510 510 510
324 412 500 550 550 550 550 550 550
14
179 289 425 463 463 550 550 550 550
281 358 434 543 550 511 550 550 550
15
145 234 344 428 434 475 507 507 507
246 313 380 476 550 448 550 550 550 550 550 550 550 550 550 550
16
119 192 282 351 396 390 467 467 467 550 550 550 550 550 550 550
277 336 420 550 395 495 550 550 512 550 550 550 550 550 550
17
159 234 291 366 324 404 443 443 488 526 526 526 526 526 526
246 299 374 507 352 441 530 550 456 508 550 550 550 550 550 550 550 550 550 550 550 550
18
134 197 245 317 272 339 397 408 409 456 490 490 490 490 490 550 550 550 550 550 550 550
221 268 335 454 315 395 475 550 408 455 547 550 550 550 550 514 550 550 550 550 550 550
19
113 167 207 269 230 287 336 383 347 386 452 455 455 455 455 494 523 523 523 523 523 523
199 241 302 409 284 356 428 525 368 410 493 550 550 550 550 463 550 550 550 550 550 550
20
97 142 177 230 197 246 287 347 297 330 386 426 426 426 426 423 490 490 490 490 490 490
218 273 370 257 322 388 475 333 371 447 503 548 550 550 420 506 550 550 550 550 550
21
123 153 198 170 212 248 299 255 285 333 373 405 406 406 364 426 460 460 460 460 460
199 249 337 234 293 353 432 303 337 406 458 498 550 550 382 460 518 550 550 550 550
22
106 132 172 147 184 215 259 222 247 289 323 351 385 385 316 370 414 438 438 438 438
181 227 308 214 268 322 395 277 308 371 418 455 507 550 349 420 473 516 550 550 550
23
93 116 150 128 160 188 226 194 216 252 282 307 339 363 276 323 362 393 418 418 418
166 208 282 196 245 295 362 254 283 340 384 418 465 550 320 385 434 473 526 550 550
24
81 101 132 113 141 165 199 170 189 221 248 269 298 346 242 284 318 345 382 396 396
180 226 272 334 234 260 313 353 384 428 514 294 355 400 435 485 550 550
25
100 124 145 175 150 167 195 219 238 263 311 214 250 281 305 337 377 377
166 209 251 308 216 240 289 326 355 395 474 272 328 369 402 448 538 550
26
88 110 129 156 133 148 173 194 211 233 276 190 222 249 271 299 354 361
154 193 233 285 200 223 268 302 329 366 439 252 303 342 372 415 498 550
27
79 98 115 139 119 132 155 173 188 208 246 169 198 222 241 267 315 347
Joist Designation 8K1 10K1 12K1 12K3 12K5 14K1 14K3 14K4 14K6 16K2 16K3 16K4 16K5 16K6 16K7 16K9 18K3 18K4 18K5 18K6 18K7 18K9 18K10
Depth (in.) 8 10 12 12 12 14 14 14 14 16 16 16 16 16 16 16 18 18 18 18 18 18 18
Approx. Wt. (plf) 5.1 5.0 5.0 5.7 7.1 5.2 6.0 6.7 7.7 5.5 6.3 7.0 7.5 8.1 8.6 10.0 6.6 7.2 7.7 8.5 9.0 10.2 11.7
143 180 216 265 186 207 249 281 306 340 408 234 282 318 346 385 463 548
28
70 88 103 124 106 118 138 155 168 186 220 151 177 199 216 239 282 331
173 193 232 261 285 317 380 218 263 296 322 359 431 511
29
95 106 124 139 151 167 198 136 159 179 194 215 254 298
161 180 216 244 266 296 355 203 245 276 301 335 402 477
30
86 96 112 126 137 151 178 123 144 161 175 194 229 269
151 168 203 228 249 277 332 190 229 258 281 313 376 446
31
78 87 101 114 124 137 161 111 130 146 158 175 207 243
142 158 190 214 233 259 311 178 215 242 264 294 353 418
32
71 79 92 103 112 124 147 101 118 132 144 159 188 221
168 202 228 248 276 332 393
33
92 108 121 131 145 171 201
158 190 214 233 260 312 370
34
84 98 110 120 132 156 184
149 179 202 220 245 294 349
35
77 90 101 110 121 143 168
141 169 191 208 232 278 330
36
70 82 92 101 111 132 154
37

38

39

40

41

42

43

44

45

46

47
Joist Designation 8K1 10K1 12K1 12K3 12K5 14K1 14K3 14K4 14K6 16K2 16K3 16K4 16K5 16K6 16K7 16K9 18K3 18K4 18K5 18K6 18K7 18K9 18K10
Depth (in.) 8 10 12 12 12 14 14 14 14 16 16 16 16 16 16 16 18 18 18 18 18 18 18
Approx. Wt. (plf) 5.1 5.0 5.0 5.7 7.1 5.2 6.0 6.7 7.7 5.5 6.3 7.0 7.5 8.1 8.6 10.0 6.6 7.2 7.7 8.5 9.0 10.2 11.7

48

49

50

51

52

53

54

55

56

57

58

59

60

Notes:
1. BLUE figures in above Load Table give TOTAL safe uniformly distributed load-carrying capacities, in pounds per linear foot, of K-series joists.
2. Weight of DEAD loads, including joists, must be deducted to determine LIVE load-carrying capacities of joists.
3. Load Table above may be used for parallel chord joists installed to maximum of 1/2 per foot slope.
4. Figures shown in RED in above Load Table are LIVE loads per linear foot of joist which will produce approximate deflection of 1/360 of span.
5. Live loads which will produce deflection of 1/240 of span may be obtained by multiplying figures in RED by 1.5
6. In no case shall TOTAL load capacity of joists be exceeded.
7. Approximate joist weights per linear foot shown in above Load Table do NOT include accessories.
8. Approximate moment of inertia of joist, in in.^4 is: Ij = 26.767*W (LL)*L^3/1000000, where W(LL) = RED figure in Table and L = (Span-0.33) in feet.
9. For concentrated and/or varying loads, add an "SP" after joist designation on joist loading diagram on design drawings, and note that joist supplier
shall design joist to support loads as shown.
10. Where joist span exceeds shaded area of above Load Table, row of bridging nearest midspan shall be diagonal bridging with bolted connections at
chords and midspan.
Joist Designation 20K3 20K4 20K5 20K6 20K7 20K9 20K10 22K4 22K5 22K6 22K7 22K9 22K10 22K11 24K4 24K5 24K6 24K7 24K8 24K9 24K10 24K12
Depth (in.) 20 20 20 20 20 20 20 22 22 22 22 22 22 22 24 24 24 24 24 24 24 24
Approx. Wt. (plf) 6.7 7.6 8.2 8.9 9.3 10.8 12.2 8.0 8.8 9.2 9.7 11.3 12.6 13.8 8.4 9.3 9.7 10.1 11.5 12.0 13.1 16.0
Span (ft.)

10

11

12

13

14

15

16

17

18

19
517 550 550 550 550 550 550
20
517 550 550 550 550 550 550
468 550 550 550 550 550 550
21
453 520 520 520 520 520 520
426 514 550 550 550 550 550 550 550 550 550 550 550 550
22
393 461 490 490 490 490 490 548 548 548 548 548 548 548
389 469 529 550 550 550 550 518 550 550 550 550 550 550
23
344 402 451 468 468 468 468 491 518 518 518 518 518 518
357 430 485 528 550 550 550 475 536 550 550 550 550 550 520 550 550 550 550 550 550 550
24
302 353 396 430 448 448 448 431 483 495 495 495 495 495 516 544 544 544 544 544 544 544
329 396 446 486 541 550 550 438 493 537 550 550 550 550 479 540 550 550 550 550 550 550
25
266 312 350 380 421 426 426 381 427 464 474 474 474 474 456 511 520 520 520 520 520 520
304 366 412 449 500 550 550 404 455 496 550 550 550 550 442 499 543 550 550 550 550 550
26
236 277 310 337 373 405 405 338 379 411 454 454 454 454 405 453 493 499 499 499 499 499
281 339 382 416 463 550 550 374 422 459 512 550 550 550 410 462 503 550 550 550 550 550
27
211 247 277 301 333 389 389 301 337 367 406 432 432 432 361 404 439 479 479 479 479 479
Joist Designation 20K3 20K4 20K5 20K6 20K7 20K9 20K10 22K4 22K5 22K6 22K7 22K9 22K10 22K11 24K4 24K5 24K6 24K7 24K8 24K9 24K10 24K12
Depth (in.) 20 20 20 20 20 20 20 22 22 22 22 22 22 22 24 24 24 24 24 24 24 24
Approx. Wt. (plf) 6.7 7.6 8.2 8.9 9.3 10.8 12.2 8.0 8.8 9.2 9.7 11.3 12.6 13.8 8.4 9.3 9.7 10.1 11.5 12.0 13.1 16.0
261 315 355 386 430 517 550 348 392 427 475 550 550 550 381 429 467 521 550 550 550 550
28
189 221 248 269 298 353 375 270 302 328 364 413 413 413 323 362 393 436 456 456 456 456
243 293 330 360 401 482 550 324 365 398 443 532 550 550 354 400 435 485 536 550 550 550
29
170 199 223 242 268 317 359 242 272 295 327 387 399 399 290 325 354 392 429 436 436 436
227 274 308 336 374 450 533 302 341 371 413 497 550 550 331 373 406 453 500 544 550 550
30
153 179 201 218 242 286 336 219 245 266 295 349 385 385 262 293 319 353 387 419 422 422
212 256 289 314 350 421 499 283 319 347 387 465 550 550 310 349 380 424 468 510 550 550
31
138 162 182 198 219 259 304 198 222 241 267 316 369 369 237 266 289 320 350 379 410 410
199 240 271 295 328 395 468 265 299 326 363 436 517 549 290 327 357 397 439 478 549 549
32
126 147 165 179 199 235 276 180 201 219 242 287 337 355 215 241 262 290 318 344 393 393
187 226 254 277 309 371 440 249 281 306 341 410 486 532 273 308 335 373 413 449 532 532
33
114 134 150 163 181 214 251 164 183 199 221 261 307 334 196 220 239 265 289 313 368 368
176 212 239 261 290 349 414 235 265 288 321 386 458 516 257 290 315 351 388 423 502 516
34
105 122 137 149 165 195 229 149 167 182 202 239 280 314 179 201 218 242 264 286 337 344
166 200 226 246 274 329 390 221 249 272 303 364 432 494 242 273 297 331 366 399 473 501
35
96 112 126 137 151 179 210 137 153 167 185 219 257 292 164 184 200 221 242 262 308 324
157 189 213 232 259 311 369 209 236 257 286 344 408 467 229 258 281 313 346 377 447 487
36
88 103 115 125 139 164 193 126 141 153 169 201 236 269 150 169 183 203 222 241 283 306
148 179 202 220 245 294 349 198 223 243 271 325 386 442 216 244 266 296 327 356 423 474
37
81 95 106 115 128 151 178 116 130 141 156 185 217 247 138 155 169 187 205 222 260 290
141 170 191 208 232 279 331 187 211 230 256 308 366 419 205 231 252 281 310 338 401 461
38
74 87 98 106 118 139 164 107 119 130 144 170 200 228 128 143 156 172 189 204 240 275
133 161 181 198 220 265 314 178 200 218 243 292 347 397 195 219 239 266 294 320 380 449
39
69 81 90 98 109 129 151 98 110 120 133 157 185 211 118 132 144 159 174 189 222 261
127 153 172 188 209 251 298 169 190 207 231 278 330 377 185 208 227 253 280 304 361 438
40
64 75 84 91 101 119 140 91 102 111 123 146 171 195 109 122 133 148 161 175 206 247
161 181 197 220 264 314 359 176 198 216 241 266 290 344 427
41
85 95 103 114 135 159 181 101 114 124 137 150 162 191 235
153 173 188 209 252 299 342 168 189 206 229 253 276 327 417
42
79 88 96 106 126 148 168 94 106 115 127 139 151 177 224
146 165 179 200 240 285 326 160 180 196 219 242 263 312 406
43
73 82 89 99 117 138 157 88 98 107 118 130 140 165 213
139 157 171 191 229 272 311 153 172 187 209 231 251 298 387
44
68 76 83 92 109 128 146 82 92 100 110 121 131 154 199
146 164 179 199 220 240 285 370
45
76 86 93 103 113 122 144 185
139 157 171 191 211 230 272 354
46
71 80 87 97 106 114 135 174
133 150 164 183 202 220 261 339
47
67 75 82 90 99 107 126 163
Joist Designation 20K3 20K4 20K5 20K6 20K7 20K9 20K10 22K4 22K5 22K6 22K7 22K9 22K10 22K11 24K4 24K5 24K6 24K7 24K8 24K9 24K10 24K12
Depth (in.) 20 20 20 20 20 20 20 22 22 22 22 22 22 22 24 24 24 24 24 24 24 24
Approx. Wt. (plf) 6.7 7.6 8.2 8.9 9.3 10.8 12.2 8.0 8.8 9.2 9.7 11.3 12.6 13.8 8.4 9.3 9.7 10.1 11.5 12.0 13.1 16.0
128 144 157 175 194 211 250 325
48
63 70 77 85 93 101 118 153
49

50

51

52

53

54

55

56

57

58

59

60

in Table and L = (Span-0.33) in feet.


n drawings, and note that joist supplier

gonal bridging with bolted connections at


Joist Designation 26K5 26K6 26K7 26K8 26K9 26K10 26K12 28K6 28K7 28K8 28K9 28K1028K12 30K7 30K8 30K9 30K10 30K11 30K12
Depth (in.) 26 26 26 26 26 26 26 28 28 28 28 28 28 30 30 30 30 30 30
Approx. Wt. (plf) 9.8 10.6 10.9 12.1 12.2 13.8 16.6 11.4 11.8 12.7 13.0 14.3 17.1 12.3 13.2 13.4 15.0 16.4 17.6
Span (ft.)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
542 550 550 550 550 550 550
26
535 541 541 541 541 541 541
502 547 550 550 550 550 550
27
477 519 522 522 522 522 522
Joist Designation 26K5 26K6 26K7 26K8 26K9 26K10 26K12 28K6 28K7 28K8 28K9 28K1028K12 30K7 30K8 30K9 30K10 30K11 30K12
Depth (in.) 26 26 26 26 26 26 26 28 28 28 28 28 28 30 30 30 30 30 30
Approx. Wt. (plf) 9.8 10.6 10.9 12.1 12.2 13.8 16.6 11.4 11.8 12.7 13.0 14.3 17.1 12.3 13.2 13.4 15.0 16.4 17.6
466 508 550 550 550 550 550 548 550 550 550 550 550
28
427 464 501 501 501 501 501 541 543 543 543 543 543
434 473 527 550 550 550 550 511 550 550 550 550 550
29
384 417 463 479 479 479 479 486 522 522 522 522 522
405 441 492 544 550 550 550 477 531 550 550 550 550 550 550 550 550 550 550
30
346 377 417 457 459 459 459 439 486 500 500 500 500 543 543 543 543 543 543
379 413 460 509 550 550 550 446 497 550 550 550 550 534 550 550 550 550 550
31
314 341 378 413 444 444 444 397 440 480 480 480 480 508 520 520 520 520 520
356 387 432 477 519 549 549 418 466 515 549 549 549 501 549 549 549 549 549
32
285 309 343 375 407 431 431 361 400 438 463 463 463 461 500 500 500 500 500
334 364 406 448 488 532 532 393 438 484 527 532 532 471 520 532 532 532 532
33
259 282 312 342 370 404 404 329 364 399 432 435 435 420 460 468 468 468 468
315 343 382 422 459 516 516 370 412 456 496 516 516 443 490 516 516 516 516
34
237 257 285 312 338 378 378 300 333 364 395 410 410 384 420 441 441 441 441
297 323 360 398 433 501 501 349 389 430 468 501 501 418 462 501 501 501 501
35
217 236 261 286 310 356 356 275 305 333 361 389 389 351 384 415 415 415 415
280 305 340 376 409 486 487 330 367 406 442 487 487 395 436 475 487 487 487
36
199 216 240 263 284 334 334 252 280 306 332 366 366 323 353 383 392 392 392
265 289 322 356 387 460 474 312 348 384 418 474 474 373 413 449 474 474 474
37
183 199 221 242 262 308 315 232 257 282 305 344 344 297 325 352 374 374 374
251 274 305 337 367 436 461 296 329 364 396 461 461 354 391 426 461 461 461
38
169 184 204 223 241 284 299 214 237 260 282 325 325 274 300 325 353 353 353
238 260 289 320 348 413 449 280 313 346 376 447 449 336 371 404 449 449 449
39
156 170 188 206 223 262 283 198 219 240 260 306 308 253 277 300 333 333 333
227 247 275 304 331 393 438 266 297 328 357 424 438 319 353 384 438 438 438
40
145 157 174 191 207 243 269 183 203 222 241 284 291 234 256 278 315 315 315
215 235 262 289 315 374 427 253 283 312 340 404 427 303 335 365 427 427 427
41
134 146 162 177 192 225 256 170 189 206 224 263 277 217 238 258 300 300 300
205 224 249 275 300 356 417 241 269 297 324 384 417 289 320 348 413 417 417
42
125 136 150 164 178 210 244 158 175 192 208 245 264 202 221 240 282 284 284
196 213 238 263 286 339 407 230 257 284 309 367 407 276 305 332 394 407 407
43
116 126 140 153 166 195 232 147 163 179 194 228 252 188 206 223 263 270 270
187 204 227 251 273 324 398 220 245 271 295 350 398 263 291 317 376 398 398
44
108 118 131 143 155 182 222 137 152 167 181 212 240 176 192 208 245 258 258
179 194 217 240 261 310 389 210 234 259 282 334 389 251 278 303 359 389 389
45
101 110 122 133 145 170 212 128 142 156 169 198 229 164 179 195 229 246 246
171 186 207 229 250 296 380 201 224 248 270 320 380 241 266 290 344 380 380
46
95 103 114 125 135 159 203 120 133 146 158 186 219 153 168 182 214 236 236
164 178 199 219 239 284 369 192 214 237 258 306 372 230 255 277 329 372 372
47
89 96 107 117 127 149 192 112 125 136 148 174 210 144 157 171 201 226 226
Joist Designation 26K5 26K6 26K7 26K8 26K9 26K10 26K12 28K6 28K7 28K8 28K9 28K1028K12 30K7 30K8 30K9 30K10 30K11 30K12
Depth (in.) 26 26 26 26 26 26 26 28 28 28 28 28 28 30 30 30 30 30 30
Approx. Wt. (plf) 9.8 10.6 10.9 12.1 12.2 13.8 16.6 11.4 11.8 12.7 13.0 14.3 17.1 12.3 13.2 13.4 15.0 16.4 17.6
157 171 190 210 229 272 353 184 206 227 247 294 365 221 244 266 315 362 365
48
83 90 100 110 119 140 180 105 117 128 139 163 201 135 148 160 188 215 216
150 164 183 202 220 261 339 177 197 218 237 282 357 212 234 255 303 347 357
49
78 85 94 103 112 131 169 99 110 120 130 153 193 127 139 150 177 202 207
144 157 175 194 211 250 325 170 189 209 228 270 350 203 225 245 291 333 350
50
73 80 89 97 105 124 159 93 103 113 123 144 185 119 130 141 166 190 199
139 151 168 186 203 241 313 163 182 201 219 260 338 195 216 235 279 320 343
51
69 75 83 91 99 116 150 88 97 106 115 136 175 112 123 133 157 179 192
133 145 162 179 195 231 301 157 175 193 210 250 325 188 208 226 268 308 336
52
65 71 79 86 93 110 142 83 92 100 109 128 165 106 116 126 148 169 184
151 168 186 203 240 313 181 200 218 258 296 330
53
78 87 95 103 121 156 100 109 119 140 159 177
145 162 179 195 232 301 174 192 209 249 285 324
54
74 82 89 97 114 147 94 103 112 132 150 170
140 156 173 188 223 290 168 185 202 240 275 312
55
70 77 85 92 108 139 89 98 106 125 142 161
135 151 166 181 215 280 162 179 195 231 265 301
56
66 73 80 87 102 132 84 92 100 118 135 153
156 173 188 223 256 290
57
80 88 95 112 128 145
151 167 181 215 247 280
58
76 83 90 106 121 137
146 161 175 208 239 271
59
72 79 86 101 115 130
141 156 169 201 231 262
60
69 75 81 96 109 124
"JOIST.xls" Program
Version 1.6

KCS-SERIES JOIST ANALYSIS


For KCS-Series Steel Joists Considered as Simple-Span Beams
Subjected to Non-Standard Loads
Job Name: Subject: wm(allow) =
Job Number: Originator: Checker: V(allow) =
wv(allow) =
Input Data: c w(use) =
e D(max) =
Joist Data: b
Designation = 18KCS3 a
Span, L = 35.0000 ft. +P +M we
Modulus, E = 29000000 psi +wb Loading Functions Evaluated
Inertia, Ix = 164.00 in.^4 (from KCS Joists Load Table) +w
Depth, D = 18 in. (from KCS Joists Load Table) ###
Weight, w = 11.0 lbs./ft. (from KCS Joists Load Table) E,I L ###
RL x RR ###
Nomenclature ###
Allowable Capacity Loads: ###
M(allow) = 44333.3 ft-lbs M(allow) = (value from KCS Joists Load Table)*1000/12 ###
wm(allow) = 289.52 plf wm(allow) = 8*M(allow)/L^2 ###
V(allow) = 5200 lbs. V(allow) = value from KCS Joists Load Table ###
wv(allow) = 297.14 plf wv(allow) = 2*V(allow)/L ###
w(use) = 289.52 plf w(use) = Minimum of wm(allow) and wv(allow) ###
###
###
Actual Design Loads: ###
Full Uniform: ###
w= 200 plf ###
Start End ###
Distributed: b (ft.) wb (plf) e (ft.) we (plf) Point Loads: a (ft.) P (lbs.) ###
#1: 11.0000 0 15.0000 100 #1: 15.0000 500 ###
#2: 15.0000 80 20.0000 80 #2: 20.0000 500 ###
#3: 20.0000 100 24.0000 0 #3: ###
#4: #4: ###
#5: #5: ###
#6: #6: ###
#7: #7: ###
#8: #8: ###
#9: ###
Moments: c (ft.) M (ft-lbs) #10: ###
#1: #11: ###
#2: #12: ###
#3: #13: ###
#4: #14: ###
#15: ###
###
###
###
###
###
###
###
###
###

21 of 41 03/19/2019 08:34:11
"JOIST.xls" Program
Version 1.6

###

22 of 41 03/19/2019 08:34:11
"JOIST.xls" Program
Version 1.6

###
Results of Joist Analysis: ###
###
Allowable Capacity Loads: ###
###
End Reactions: ###
RL = 5200.0 lbs. RR = 5200.0 lbs. ###
###
Web Member Shear: ###
Vw = 5200 lbs. Note: all joist web members are designed for a vertical shear equal to this value User x1
User x2
Maximum Moments: x=a1 for P1
+Mx(max) = 44333.3 ft-lbs @ x= 17.50 ft. Note: moment is constant for distance = 2*D from eachx=a2
end for P2
-Mx(max) = 0.0 ft-lbs @ x= 0.00 ft. Note: moment is constant for distance = 2*D from eachx=a3
end for P3
x=a4 for P4
*Maximum Deflections: x=a5 for P5
-D(max) = -2.364 in. @x= 17.50 ft. x=a6 for P6
+D(max) = 0.000 in. @x= 0.00 ft. x=a7 for P7
D(ratio) = L/178 x=a8 for P8
*Note: deflections shown above include a 15% increase above the values calculated using traditional x=a9 for P9
"simple-beam" flexure in order to more closely match actual test results obtained by SJI. x=a10 for P10
x=a11 for P11
x=a12 for P12
Actual Design Loads: x=a13 for P13
x=a14 for P14
End Reactions: x=a15 for P15
RL = 4400.0 lbs. RR = 4400.0 lbs. x=c1 for M1
x=c2 for M2
Maximum Moments: x=c3 for M3
+Mx(max) = 44108.3 ft-lbs @x= 17.50 ft. x=c4 for M4
-Mx(max) = 0.0 ft-lbs @x= 0.00 ft. x for Vx=0(1)
x for qx=0(1)
*Maximum Deflections: x for Vx=0(2)
-D(max) = -2.282 in. @x= 17.50 ft. x for qx=0(2)
+D(max) = 0.000 in. @x= 0.00 ft.
D(ratio) = L/184
*Note: deflections shown above include a 15% increase above the values calculated using traditional KCS JOISTS LOAD TAB
"simple-beam" flexure in order to more closely match actual test results obtained by SJI. Gross
Joist
Designation
Maximum Stress Ratios: (in.-kips)
10KCS1
S.R. = 0.846 for Shear @ x= 35.00 ft. 10KCS2
S.R. = 0.995 for Moment @ x= 17.50 ft. 10KCS3
12KCS1
12KCS2
Comments: 12KCS3
14KCS1
14KCS2
14KCS3
16KCS2
16KCS3
16KCS4
16KCS5

23 of 41 03/19/2019 08:34:11
Moment (ft-lbs.) Shear (lbs.)

-6000.0
-4000.0
-2000.0
2000.0
4000.0
6000.0

0.0

0.0
5000.0
10000.0
15000.0
20000.0
25000.0
30000.0
35000.0
40000.0
45000.0
50000.0
0.0000 0.0000
0.7000 0.7000
1.4000 1.4000
2.1000 2.1000
2.8000 2.8000
3.5000 3.5000
4.2000 4.2000
4.9000 4.9000
5.6000 5.6000
6.3000 6.3000
7.0000 7.0000
7.7000 7.7000
8.4000 8.4000
9.1000 9.1000
9.8000 9.8000
10.5000 10.5000
11.2000 11.2000
11.9000 11.9000
12.6000 12.6000
13.3000 13.3000
14.0000 14.0000
14.7000 14.7000
15.4000 15.4000
16.1000 16.1000

24 of 41
16.8000 16.8000
17.5000 17.5000

x (ft.)
18.2000

x (ft.)
18.2000
18.9000 18.9000
19.6000 19.6000
Shear Diagram

20.3000 20.3000

Moment Diagram
21.0000 21.0000
21.7000 21.7000
22.4000 22.4000
23.1000 23.1000
23.8000 23.8000
24.5000 24.5000
25.2000 25.2000
25.9000 25.9000
26.6000 26.6000
27.3000 27.3000
28.0000 28.0000
28.7000 28.7000
29.4000 29.4000
30.1000 30.1000
30.8000 30.8000
31.5000 31.5000
32.2000 32.2000
32.9000 32.9000
33.6000 33.6000
34.3000 34.3000
35.0000 35.0000

03/19/2019 08:34:11
Version 1.6
"JOIST.xls" Program

###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
###
30KCS5
30KCS4
30KCS3
28KCS5
28KCS4
28KCS3
28KCS2
26KCS5
26KCS4
26KCS3
26KCS2
24KCS5
24KCS4
24KCS3
24KCS2
22KCS5
22KCS4
22KCS3
22KCS2
20KCS5
20KCS4
20KCS3
20KCS2
18KCS5
18KCS4
18KCS3
18KCS2

** Does no
load cann
* Maximum
"JOIST.xls" Program
Version 1.6

= curves for allowable capacity loads = curves for actual design loads ###
###

25 of 41 03/19/2019 08:34:11
KCS JOISTS LOAD TABLE
Gross Bridging
Joist Depth Moment Shear Approx. Moment Table
Designation (inches) Capacity* Capacity* Weight** of Inertia Section
(in.-kips) (lbs.) (plf) (in.^4) Number
10KCS1 10 172 2000 6.0 29 1
10KCS2 10 225 2500 7.5 37 1
10KCS3 10 296 3000 10.0 47 1
12KCS1 12 209 2400 6.0 43 3
12KCS2 12 274 3000 8.0 55 5
12KCS3 12 362 3500 10.0 71 5
14KCS1 14 247 2900 6.5 59 4
14KCS2 14 324 3400 8.0 77 6
14KCS3 14 428 3900 10.0 99 6
16KCS2 16 349 4000 8.5 99 6
16KCS3 16 470 4800 10.5 128 9
16KCS4 16 720 5300 14.5 192 9
16KCS5 16 934 5800 18.0 245 9
18KCS2 18 395 4700 9.0 127 6
18KCS3 18 532 5200 11.0 164 9
18KCS4 18 817 5700 15.0 247 10
18KCS5 18 1062 6200 18.5 316 10
20KCS2 20 442 5200 9.5 159 6
20KCS3 20 595 6000 11.5 205 9
20KCS4 20 914 7900 16.5 308 10
20KCS5 20 1191 8400 20.0 396 10
22KCS2 22 488 5900 10.0 194 6
22KCS3 22 658 6600 12.5 251 9
22KCS4 22 1012 7900 16.5 377 11
22KCS5 22 1319 8600 20.5 485 11
24KCS2 24 534 6300 10.0 232 6
24KCS3 24 720 7200 12.5 301 9
24KCS4 24 1108 8400 16.5 453 12
24KCS5 24 1448 8900 20.5 584 12
26KCS2 26 580 6600 10.0 274 6
26KCS3 26 783 7800 12.5 355 9
26KCS4 26 1206 8500 16.5 536 12
26KCS5 26 1576 9200 20.5 691 12
28KCS2 28 626 6900 10.5 320 6
28KCS3 28 846 8000 12.5 414 9
28KCS4 28 1303 8500 16.5 626 12
28KCS5 28 1704 9200 20.5 808 12
30KCS3 30 908 8000 13.0 478 9
30KCS4 30 1400 8500 16.5 722 12
30KCS5 30 1833 9200 21.0 934 12
* Maximum uniformly distributed load capacity is 550 plf and single
concentrated load cannot exceed shear capacity.
** Does not include accessories.
"JOIST.xls" Program
Version 1.6

LH-SERIES JOIST ANALYSIS


For Uniformly Loaded, Longspan Steel Joists
Using Steel Joist Institute (SJI) Standard Load Tables
Job Name: Subject:
Job Number: Originator: Checker:

Input Data:
Joist Designation (Size) = 32LH06 +W(TL)= 373.0
Joist Span, L = 40.0 ft.
Joist Spacing, S = 4.0000 ft.
Unif. Dead Load, w(DL) = 20.00 psf
Unif. Live Load, w(LL) = 73.25 psf E,Ix L=40
Deflect. Factor, DF(LL) = 360
RL=7460 RR=7460
Results: Nomenclature
Required Loads:
Dead Load, W(DL) = 80.0 plf W(DL) = w(DL)*S Joist Designation
Live Load, W(LL) = 293.0 plf W(LL) = w(LL)*S Depth (in.)
Total Load, W(TL) = 373.0 plf W(TL) = W(DL)+W(LL) Approx. Wt. (lbs./ft.)
Reactions, RL & RR = 7460.0 lbs. RL = RR = W(TL)*L/2 Span (ft.)
###
###
For Joist Selected ###
Joist Joist Joist Allowable Loads and Stress Ratios # Rows ###
Size Weight Inertia, Ix W(TL) Flexure W(LL) Deflect. of ###
(plf) (in.^4) (plf) Ratio (plf) Ratio Bridging ###
32LH06 14 526.4 411 0.908 315 0.930 **3 ###
###
15 Lightest Acceptable LH-series Joist Systems ###
Joist Joist Joist Allowable Loads and Stress Ratios # Rows ###
Sizes Weight Inertia, Ix W(TL) Flexure W(LL) Deflect. of ###
(plf) (in.^4) (plf) Ratio (plf) Ratio Bridging ###
1 32LH06 14 526.4 411 0.908 315 0.930 **3 ###
2 28LH06 16 506.3 457 0.816 303 0.967 **3 ###
3 32LH07 16 586.5 462 0.807 351 0.835 **3 ###
4 28LH07 17 571.5 516 0.723 342 0.857 **3 ###
5 32LH08 17 635.0 502 0.743 380 0.771 **3 ###
6 28LH08 18 609.9 553 0.675 365 0.803 **3 ###
7 24LH09 21 563.1 632 0.590 337 0.869 **2 ###
8 28LH09 21 750.3 681 0.548 449 0.653 **2 ###
9 32LH09 21 795.4 629 0.593 476 0.616 **2 ###
10 32LH10 21 877.3 696 0.536 525 0.558 **2 ###
11 24LH10 23 631.7 702 0.531 378 0.775 **2 ###
12 28LH10 23 817.1 745 0.501 489 0.599 **2 ###
13 32LH11 24 959.2 762 0.490 574 0.510 **2 ###
14 24LH11 25 698.5 768 0.486 418 0.701 **2 ###
15 28LH11 25 874.0 799 0.467 523 0.560 **2 ###
**(1-6) Denotes row of bridging nearest mid-span required to be diagonal bridging. ###
**(1-6)** Denotes all rows of bridging required to be diagonal bridging. ###
###
Notes: 1. OSHA is interpreting Section 29CFR-1926.751(c)2 to mean all joists whose length ###
>= 40' require bolted diagonal bridging in place before slackening of hoisting lines. ###
2. For point loads on LH-series joists, the magnitude and location of load should be ###
indicated on the design drawings and "SP" must be added to the joist designation. ###

27 of 41 03/19/2019 08:34:11
"JOIST.xls" Program
Version 1.6

###

28 of 41 03/19/2019 08:34:11
Joist Designation 18LH02 18LH03 18LH04 18LH05 18LH06 18LH07 18LH08 18LH09 20LH02 20LH03 20LH04 20LH05 20LH06 20LH07 20LH08 20LH09 20LH10 24LH03 24LH04 24LH05 24LH06 24LH07 24LH08 24LH09 24LH10 24LH11
Depth (in.) 18 18 18 18 18 18 18 18 20 20 20 20 20 20 20 20 20 24 24 24 24 24 24 24 24 24
Approx. Wt. (plf) 10 11 12 15 15 17 19 21 10 11 12 14 15 17 19 21 23 11 12 13 16 17 18 21 23 25
Span (ft.)
554 614 715 808 955 992 1034 1108
21
439 488 566 637 738 776 810 864
529 587 684 772 913 948 988 1059 498 529 648 697 931 993 1023 1120 1209
22
401 446 517 582 674 709 740 790 392 432 549 589 777 830 858 935 1008
507 562 655 739 875 908 946 1014 477 507 621 668 891 951 980 1073 1158
23
368 409 474 534 619 650 679 724 360 396 503 540 713 761 787 857 924
486 539 628 709 839 872 908 973 458 486 596 640 855 912 940 1030 1111
24
339 377 436 492 570 599 625 667 331 365 463 497 656 701 724 789 851
468 521 604 684 809 840 876 936 442 469 574 616 822 878 908 990 1068
25
313 348 403 454 526 553 577 616 306 337 428 459 606 647 669 729 786
442 493 571 648 749 809 843 901 437 463 566 609 791 845 873 953 1028
26
284 317 367 414 469 513 534 571 303 333 406 437 561 599 619 675 724
418 467 535 614 696 780 812 868 431 458 558 602 763 814 842 918 991
27
259 289 329 378 419 476 496 527 298 317 386 416 521 556 575 626 673
391 438 500 581 648 726 784 838 410 452 528 595 723 786 813 886 956 401 492 527 708 778 830 977 1032 1088
28
234 262 296 345 377 428 462 491 274 302 352 395 477 518 536 581 626 324 397 425 567 623 662 775 822 861
367 409 469 543 605 678 758 810 388 434 496 571 679 760 785 856 924 388 475 509 684 752 802 944 998 1052
29
212 236 266 311 340 386 427 458 250 280 320 366 427 484 500 542 585 303 371 397 529 582 618 724 768 804
345 382 440 508 566 635 717 783 365 414 467 544 635 711 760 828 894 375 460 492 662 727 776 913 965 1017
30
193 213 242 282 307 349 387 418 228 258 291 337 386 438 468 507 545 283 347 371 495 545 578 677 718 752
324 359 413 476 531 595 680 759 344 395 440 513 596 667 722 802 865 363 445 477 641 704 751 884 935 985
31
175 194 219 256 280 317 351 380 208 238 265 308 351 398 428 475 510 266 326 348 465 511 543 635 674 705
306 337 388 448 499 559 641 713 325 372 416 484 560 627 687 778 839 352 432 462 621 683 728 857 906 955
32
160 177 200 233 254 288 320 346 190 218 243 281 320 362 395 437 479 250 306 327 437 480 510 597 633 663
289 317 365 421 470 526 604 671 307 352 393 458 527 590 654 755 814 342 419 449 604 665 707 832 882 927
33
147 161 182 212 232 264 292 316 174 200 223 258 292 331 365 399 448 235 288 308 411 452 480 562 596 624
273 299 344 397 443 496 571 633 291 333 372 434 497 556 621 712 791 339 398 446 579 638 677 808 856 900
34
135 148 167 195 212 241 267 289 160 184 205 238 267 303 336 366 411 226 265 297 382 421 447 530 559 588
259 283 325 375 418 469 540 598 275 316 353 411 469 526 588 673 748 336 379 440 555 613 649 785 832 875
35
124 136 153 179 195 222 246 266 147 169 189 219 246 278 309 336 377 218 246 285 356 393 416 501 528 555
245 267 308 355 396 444 512 566 262 299 335 390 444 497 558 636 707 323 360 419 530 588 622 764 809 851
36
114 124 141 164 180 204 226 245 136 156 174 202 226 256 285 309 346 204 227 264 331 367 388 460 500 525
249 283 318 371 421 471 530 603 670 307 343 399 504 565 597 731 788 829
37
126 143 161 187 209 236 262 285 320 188 210 244 306 343 362 424 474 498
237 269 303 353 399 447 503 572 636 293 327 380 480 541 572 696 768 807
38
117 133 149 173 192 218 242 264 296 175 195 226 284 320 338 393 439 472
225 255 289 336 379 425 479 544 604 279 312 363 457 516 545 663 737 787
39
108 123 139 161 178 202 225 244 274 162 182 210 263 297 314 363 406 449
215 243 275 321 361 404 457 517 575 267 298 347 437 491 520 632 702 768
40
101 114 129 150 165 187 209 227 254 152 169 196 245 276 292 337 378 418
255 285 331 417 468 497 602 668 734
41
141 158 182 228 257 272 313 351 388
244 273 317 399 446 475 574 637 701
42
132 148 171 211 239 254 292 326 361
234 262 304 381 426 455 548 608 671
43
124 138 160 197 223 238 272 304 337
224 251 291 364 407 435 524 582 642
44
116 130 150 184 208 222 254 285 315
215 241 280 348 389 417 501 556 616
45
109 122 141 172 195 208 238 266 294
Joist Designation 18LH02 18LH03 18LH04 18LH05 18LH06 18LH07 18LH08 18LH09 20LH02 20LH03 20LH04 20LH05 20LH06 20LH07 20LH08 20LH09 20LH10 24LH03 24LH04 24LH05 24LH06 24LH07 24LH08 24LH09 24LH10 24LH11
Depth (in.) 18 18 18 18 18 18 18 18 20 20 20 20 20 20 20 20 20 24 24 24 24 24 24 24 24 24
Approx. Wt. (plf) 10 11 12 15 15 17 19 21 10 11 12 14 15 17 19 21 23 11 12 13 16 17 18 21 23 25
207 231 269 334 373 400 480 533 590
46
102 114 132 161 182 196 223 249 276
199 222 258 320 357 384 460 511 567
47
96 107 124 152 171 184 209 234 259
191 214 248 307 343 369 441 490 544
48
90 101 117 142 161 173 196 220 243

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70
Joist Designation 18LH02 18LH03 18LH04 18LH05 18LH06 18LH07 18LH08 18LH09 20LH02 20LH03 20LH04 20LH05 20LH06 20LH07 20LH08 20LH09 20LH10 24LH03 24LH04 24LH05 24LH06 24LH07 24LH08 24LH09 24LH10 24LH11
Depth (in.) 18 18 18 18 18 18 18 18 20 20 20 20 20 20 20 20 20 24 24 24 24 24 24 24 24 24
Approx. Wt. (plf) 10 11 12 15 15 17 19 21 10 11 12 14 15 17 19 21 23 11 12 13 16 17 18 21 23 25

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95
Joist Designation 18LH02 18LH03 18LH04 18LH05 18LH06 18LH07 18LH08 18LH09 20LH02 20LH03 20LH04 20LH05 20LH06 20LH07 20LH08 20LH09 20LH10 24LH03 24LH04 24LH05 24LH06 24LH07 24LH08 24LH09 24LH10 24LH11
Depth (in.) 18 18 18 18 18 18 18 18 20 20 20 20 20 20 20 20 20 24 24 24 24 24 24 24 24 24
Approx. Wt. (plf) 10 11 12 15 15 17 19 21 10 11 12 14 15 17 19 21 23 11 12 13 16 17 18 21 23 25

96
Joist Designation 18LH02 18LH03 18LH04 18LH05 18LH06 18LH07 18LH08 18LH09 20LH02 20LH03 20LH04 20LH05 20LH06 20LH07 20LH08 20LH09 20LH10 24LH03 24LH04 24LH05 24LH06 24LH07 24LH08 24LH09 24LH10 24LH11
Depth (in.) 18 18 18 18 18 18 18 18 20 20 20 20 20 20 20 20 20 24 24 24 24 24 24 24 24 24
Approx. Wt. (plf) 10 11 12 15 15 17 19 21 10 11 12 14 15 17 19 21 23 11 12 13 16 17 18 21 23 25

Notes:
1. BLUE figures in above Load Table give TOTAL safe uniformly distributed load-carrying capacities, in pounds per linear foot, of LH-series joists.
2. Weight of DEAD loads, including joists, must be deducted to determine LIVE load-carrying capacities of joists.
3. Figures shown in RED in above Load Table are LIVE loads per linear foot of joist which will produce approximate deflection of 1/360 of span.
4. Live loads which will produce deflection of 1/240 of span may be obtained by multiplying figures in RED by 1.5
5. In no case shall TOTAL load capacity of joists be exceeded.
6. Approximate joist weights per linear foot shown in above Load Table do NOT include accessories.
7. Load Table above applies to joists with either parallel chords or standard pitched top chords. When top chords are pitched, carrying capacities are
determined by nomonal depth of joists at center of span. Standard top chord pitch is 1/8" per foot. If pitch exceeds this standard, Load Table does not
apply. Load Table above may be used for parallel chord joists installed to maximum of 1/2 per foot slope.
8. Approximate moment of inertia of joist, in in.^4 is: Ij = 26.767*W (LL)*L^3/1000000, where W(LL) = RED figure in Table and L = (Span+0.67) in feet.
9. For concentrated and/or varying loads, add an "SP" after joist designation on joist loading diagram on design drawings, and note that joist supplier shall
design joist to support loads as shown.
10. Where joist span exceeds RED shaded area of above Load Table, row of bridging nearest midspan shall be diagonal bridging with bolted connections at
chords and intersection. Hoisting cables shall not be released until this row of bolted diagonal bridging is completely installed.
11. Where joist span exceeds BLUE shaded area of above Load Table, all rows of bridging shall be diagonal bridging with bolted connections at
chords and intersection. Hoisting cables shall not be released until two rows of bridging nearest third points are completely installed.
12. When holes are required in top or bottom chords, carrying capacities must be reduced inproportion to reduction of chord areas.
13. Top chords are considered as being stayed (braced) laterally by floor slab or roof deck.
Joist Designation 28LH05 28LH06 28LH07 28LH08 28LH09 28LH10 28LH11 28LH12 28LH13 32LH06 32LH07 32LH08 32LH09 32LH10 32LH11 32LH12 32LH13 32LH14 32LH15 36LH07 36LH08 36LH09 36LH10 36LH11 36LH12 36LH13 36LH14 36LH15
Depth (in.) 28 28 28 28 28 28 28 28 28 32 32 32 32 32 32 32 32 32 32 36 36 36 36 36 36 36 36 36
Approx. Wt. (plf) 13 16 17 18 21 23 25 27 30 14 16 17 21 21 24 27 30 33 35 16 18 21 21 23 25 30 36 36
Span (ft.)

21

22

23

24

25

26

27

28

29

30

31

32

416 552 624 668 823 900 965 1060 1105


33
335 443 499 533 656 714 763 835 872
404 536 606 649 799 874 937 1030 1073
34
316 417 471 503 618 673 719 787 822
392 521 589 631 777 849 911 1001 1043
35
299 394 445 475 584 636 680 744 777
382 507 573 614 755 826 886 974 1014
36
283 373 421 449 553 602 643 704 735
372 494 557 597 735 804 863 948 988
37
268 354 399 426 524 570 609 667 696
362 481 543 582 716 784 840 923 962 432 486 528 662 732 802 941 1050 1081 1117
38
254 336 379 404 497 541 578 633 661 348 388 421 526 581 635 742 825 850 878
353 469 529 567 698 764 819 900 938 421 474 514 645 713 781 918 1023 1054 1089
39
242 319 360 384 472 514 549 601 628 331 368 400 500 552 604 705 784 807 834
344 457 516 553 681 745 799 878 915 411 462 502 629 696 762 895 998 1028 1062
40
230 303 342 365 449 489 523 572 597 315 351 380 476 525 574 671 746 768 794
337 448 505 540 667 729 780 857 895 401 451 490 614 679 744 874 974 1003 1037
41
219 289 326 348 428 466 498 545 569 300 334 362 453 500 547 639 710 732 756
323 429 484 517 639 704 762 837 874 391 441 478 600 663 727 853 951 980 1012 394 434 555 612 668 799 940 1036 1092
42
205 270 305 325 400 439 475 520 543 286 318 346 432 477 522 610 678 698 721 323 354 451 499 543 647 758 833 877
310 412 464 496 612 679 736 818 854 382 431 467 586 648 710 834 930 957 989 385 424 543 598 653 781 918 1012 1067
43
192 253 285 305 375 414 448 496 518 273 304 330 413 455 498 582 647 666 688 309 338 431 476 518 617 724 795 837
297 395 445 475 586 651 711 800 835 374 421 457 573 634 694 815 909 936 967 376 414 531 584 638 763 898 989 1043
44
180 238 267 285 351 388 423 476 495 261 291 315 394 435 476 556 618 637 658 295 323 412 455 495 590 692 760 800
286 379 427 456 563 625 682 782 816 366 412 447 561 620 679 797 889 915 946 368 405 519 571 624 747 878 968 1020
45
169 223 251 268 329 364 397 454 472 250 278 302 377 416 455 532 591 609 629 282 309 394 435 474 564 662 727 765
Joist Designation 28LH05 28LH06 28LH07 28LH08 28LH09 28LH10 28LH11 28LH12 28LH13 32LH06 32LH07 32LH08 32LH09 32LH10 32LH11 32LH12 32LH13 32LH14 32LH15 36LH07 36LH08 36LH09 36LH10 36LH11 36LH12 36LH13 36LH14 36LH15
Depth (in.) 28 28 28 28 28 28 28 28 28 32 32 32 32 32 32 32 32 32 32 36 36 36 36 36 36 36 36 36
Approx. Wt. (plf) 13 16 17 18 21 23 25 27 30 14 16 17 21 21 24 27 30 33 35 16 18 21 21 23 25 30 36 36
275 364 410 438 540 600 655 766 799 358 403 437 549 606 664 780 870 896 926 360 396 508 559 611 731 859 947 999
46
159 209 236 252 309 342 373 435 452 239 266 289 361 399 436 510 566 583 603 270 296 377 417 454 541 634 696 733
265 350 394 420 519 576 629 737 782 350 394 428 537 594 650 764 852 877 906 352 388 497 548 598 715 841 927 978
47
150 197 222 236 291 322 351 408 433 229 255 277 346 382 418 489 543 559 578 259 284 361 400 435 518 607 667 703
255 337 379 403 499 554 605 709 766 343 386 419 526 581 637 748 834 859 888 345 380 487 536 586 701 824 908 957
48
142 186 209 222 274 303 331 383 415 220 245 266 332 367 401 469 521 536 554 249 272 347 383 417 497 583 640 674
245 324 365 387 481 533 582 682 751 338 379 411 516 571 625 734 817 843 870 338 372 477 525 574 687 807 890 938
49
133 175 197 209 258 285 312 361 396 211 235 255 319 352 385 450 500 515 532 239 262 333 368 400 477 559 615 647
237 313 352 371 463 513 561 656 722 326 366 397 498 550 602 712 801 826 853 332 365 468 515 562 673 791 872 920
50
126 166 186 196 243 269 294 340 373 199 223 242 302 332 363 428 480 495 511 229 251 320 354 385 459 538 591 622
228 301 339 357 446 495 540 632 694 315 353 383 480 531 580 688 785 810 837 325 358 459 505 552 660 776 855 902
51
119 156 176 185 228 255 278 321 352 189 211 229 285 315 343 406 461 476 492 220 242 308 340 370 441 517 568 598
220 291 327 344 430 477 521 609 668 304 341 369 463 512 560 664 771 795 821 319 351 450 496 541 647 761 839 885
52
113 148 166 175 216 241 263 303 332 179 200 216 270 297 325 384 444 458 473 212 233 296 327 356 424 498 547 575
213 281 316 331 415 460 502 587 643 294 329 357 447 495 541 641 742 780 805 313 345 442 486 531 635 747 824 868
53
107 140 158 165 204 228 249 285 314 169 189 205 256 282 308 364 420 440 454 204 224 285 315 343 409 479 527 554
206 271 305 319 401 444 485 566 620 284 318 345 432 478 522 619 715 766 791 307 338 434 477 521 624 733 808 852
54
102 133 150 156 193 215 236 270 297 161 179 194 243 267 292 345 397 417 438 197 216 275 304 330 394 462 507 534
199 262 295 308 387 429 468 546 598 275 308 333 418 462 505 598 690 738 776 302 332 426 469 512 613 720 794 837
55
97 126 142 148 183 204 223 256 281 153 170 184 230 254 277 327 376 395 422 190 208 265 293 319 380 445 489 515
193 253 285 297 374 415 453 527 577 266 298 322 404 445 488 578 666 713 763 296 326 418 461 503 602 708 780 822
56
92 120 135 140 173 193 212 243 266 145 162 175 219 240 263 311 354 374 407 183 201 256 283 308 367 430 472 497
257 288 312 391 430 473 559 643 688 750 292 321 411 454 495 593 697 768 809
57
138 154 167 208 228 251 295 336 355 393 177 194 247 273 297 354 415 456 480
249 279 302 379 416 458 541 621 665 725 283 311 398 440 480 575 675 755 795
58
131 146 159 198 217 239 281 319 337 374 168 185 235 260 283 338 395 434 464
242 271 293 367 402 443 524 600 643 701 274 302 386 426 465 557 654 729 781
59
125 140 151 189 206 227 267 304 321 355 160 176 224 248 269 322 376 412 448
234 262 284 356 389 429 508 581 622 678 266 293 374 413 451 540 634 706 769
60
119 133 144 180 196 216 255 288 304 338 153 168 214 236 257 307 359 392 434
227 254 275 345 376 416 492 562 602 656 258 284 363 401 438 523 615 683 744
61
114 127 137 172 186 206 243 275 290 322 146 160 204 225 246 292 342 373 413
220 247 267 335 364 403 477 544 583 635 251 276 352 389 425 508 596 661 721
62
108 121 131 164 178 196 232 262 276 306 140 153 195 215 234 279 327 356 394
214 240 259 325 353 390 463 527 564 616 244 268 342 378 412 493 579 641 698
63
104 116 125 157 169 187 221 249 264 292 134 146 186 206 224 267 312 339 375
208 233 252 315 342 378 449 511 547 597 237 260 333 367 401 478 562 621 677
64
99 111 120 149 162 179 211 238 251 279 128 140 179 197 214 255 298 323 358
230 253 323 357 389 464 546 602 656
65
122 134 171 188 205 243 285 309 342
224 246 314 347 378 450 531 584 637
66
117 128 163 180 196 232 273 295 327
218 239 306 338 368 437 516 567 618
67
112 123 157 173 188 222 262 283 312
212 233 297 328 358 424 502 551 600
68
107 118 150 165 180 213 251 270 299
207 227 289 320 348 412 488 535 583
69
103 113 144 159 173 204 240 259 286
201 221 282 311 339 400 475 520 567
70
99 109 138 152 166 195 231 247 274
Joist Designation 28LH05 28LH06 28LH07 28LH08 28LH09 28LH10 28LH11 28LH12 28LH13 32LH06 32LH07 32LH08 32LH09 32LH10 32LH11 32LH12 32LH13 32LH14 32LH15 36LH07 36LH08 36LH09 36LH10 36LH11 36LH12 36LH13 36LH14 36LH15
Depth (in.) 28 28 28 28 28 28 28 28 28 32 32 32 32 32 32 32 32 32 32 36 36 36 36 36 36 36 36 36
Approx. Wt. (plf) 13 16 17 18 21 23 25 27 30 14 16 17 21 21 24 27 30 33 35 16 18 21 21 23 25 30 36 36
196 215 275 303 330 389 463 505 551
71
95 104 133 146 159 187 222 237 263
191 209 267 295 322 378 451 492 536
72
91 100 127 140 153 179 213 228 252

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95
Joist Designation 28LH05 28LH06 28LH07 28LH08 28LH09 28LH10 28LH11 28LH12 28LH13 32LH06 32LH07 32LH08 32LH09 32LH10 32LH11 32LH12 32LH13 32LH14 32LH15 36LH07 36LH08 36LH09 36LH10 36LH11 36LH12 36LH13 36LH14 36LH15
Depth (in.) 28 28 28 28 28 28 28 28 28 32 32 32 32 32 32 32 32 32 32 36 36 36 36 36 36 36 36 36
Approx. Wt. (plf) 13 16 17 18 21 23 25 27 30 14 16 17 21 21 24 27 30 33 35 16 18 21 21 23 25 30 36 36

96
Joist Designation 40LH08 40LH09 40LH10 40LH11 40LH12 40LH13 40LH14 40LH15 40LH16 44LH09 44LH10 44LH11 44LH12 44LH13 44LH14 44LH15 44LH16 44LH17 48LH10 48LH11 48LH12 48LH13 48LH14 48LH15 48LH16 48LH17
Depth (in.) 40 40 40 40 40 40 40 40 40 44 44 44 44 44 44 44 44 44 48 48 48 48 48 48 48 48
Approx. Wt. (plf) 16 21 21 22 25 30 35 36 42 19 21 22 25 30 31 36 42 47 21 22 25 29 32 36 42 47
Span (ft.)

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45
Joist Designation 40LH08 40LH09 40LH10 40LH11 40LH12 40LH13 40LH14 40LH15 40LH16 44LH09 44LH10 44LH11 44LH12 44LH13 44LH14 44LH15 44LH16 44LH17 48LH10 48LH11 48LH12 48LH13 48LH14 48LH15 48LH16 48LH17
Depth (in.) 40 40 40 40 40 40 40 40 40 44 44 44 44 44 44 44 44 44 48 48 48 48 48 48 48 48
Approx. Wt. (plf) 16 21 21 22 25 30 35 36 42 19 21 22 25 30 31 36 42 47 21 22 25 29 32 36 42 47

46

348 457 503 550 669 789 902 1009 1112


47
285 372 410 444 541 634 727 810 890
341 448 493 538 655 773 884 988 1089
48
273 357 393 426 519 608 697 777 854
334 439 483 527 642 757 866 968 1067
49
262 343 378 409 498 584 669 746 820
328 430 474 517 630 742 849 949 1046
50
252 329 363 393 479 561 643 717 788
321 422 464 507 617 728 832 931 1026
51
242 317 349 378 460 540 619 690 758
315 414 456 497 606 714 816 913 1006 380 420 454 562 666 767 892 1029 1105
52
233 305 336 364 443 519 595 664 729 309 340 368 454 538 616 716 824 880
309 406 447 488 594 701 801 896 988 373 412 445 552 654 753 876 1010 1084
53
225 293 323 350 427 500 573 639 702 298 328 354 437 518 594 690 793 848
304 399 439 479 584 688 787 880 969 366 404 437 541 642 739 860 991 1065
54
216 283 312 338 411 482 553 616 677 287 316 341 421 499 572 665 764 817
298 392 431 471 573 675 772 864 952 359 397 429 532 631 726 844 974 1045
55
209 273 301 326 397 465 533 594 653 277 305 329 406 482 552 641 737 788
293 385 424 462 563 663 759 849 935 353 390 422 522 619 713 829 956 1027 353 383 484 579 683 785 905 1016
56
201 263 290 314 383 449 514 573 630 267 294 318 392 465 532 619 711 760 293 316 397 474 559 640 737 825
288 378 416 454 553 652 746 834 919 347 383 414 513 609 701 815 940 1009 347 376 475 569 671 772 890 999
57
195 254 280 303 370 433 497 554 608 258 284 307 379 449 514 597 687 734 283 305 383 457 539 618 712 796
283 372 409 447 544 641 733 820 903 341 377 407 505 598 689 801 924 992 341 370 467 559 660 758 874 982
58
188 246 271 293 357 418 480 535 588 249 274 296 366 434 497 577 664 710 273 295 370 442 521 597 688 769
278 365 402 439 535 630 721 806 888 335 370 401 496 588 677 788 908 975 335 364 459 550 649 746 860 965
59
182 237 262 283 345 405 464 517 568 241 265 287 354 419 480 558 642 686 264 285 358 427 504 577 665 744
274 359 396 432 526 620 709 793 874 330 364 394 488 579 666 775 893 959 330 358 452 541 638 733 846 949
60
176 230 253 274 334 391 449 500 549 233 257 277 342 405 464 540 621 664 256 275 346 413 487 558 643 719
269 353 389 425 517 610 697 780 859 324 358 388 480 569 655 762 879 944 324 352 444 532 628 722 832 934
61
170 222 245 265 323 379 434 484 532 225 248 268 331 392 450 522 601 642 247 267 335 400 472 540 623 696
265 348 383 418 509 600 686 768 846 319 353 381 472 560 645 750 865 929 319 346 437 523 618 710 819 919
62
165 215 237 257 313 367 421 469 515 218 240 260 321 380 435 506 582 622 239 258 324 387 457 523 603 674
261 342 377 411 501 591 675 755 832 314 347 375 465 551 635 738 851 914 314 341 430 515 608 699 806 905
63
160 209 230 249 303 355 407 454 499 212 233 252 311 368 422 490 564 602 232 250 314 375 443 507 584 653
257 337 371 405 493 581 665 744 820 309 342 370 458 543 625 727 838 900 309 336 424 507 598 688 793 891
64
155 202 223 241 294 344 395 440 484 205 226 244 301 357 409 475 546 584 225 242 305 364 429 491 566 633
254 332 367 399 486 573 656 734 808 305 337 364 451 534 615 716 825 886 305 330 417 499 589 678 781 877
65
150 196 216 234 285 334 383 427 469 199 219 237 292 346 396 461 530 566 218 235 295 353 416 476 549 614
247 323 357 388 472 557 638 712 796 300 331 358 444 526 606 705 813 873 300 325 411 492 580 667 769 864
66
144 188 207 224 273 320 367 408 455 193 212 230 283 336 385 447 514 549 212 228 287 342 404 462 533 596
241 315 347 378 459 542 620 691 784 296 327 353 437 519 597 695 801 860 296 321 405 485 572 658 758 851
67
138 180 198 215 261 307 351 390 441 187 206 223 275 326 373 434 499 533 205 221 278 332 392 449 517 578
234 306 338 368 447 528 603 671 772 291 322 348 431 511 588 684 789 848 291 316 399 478 564 648 747 839
68
132 173 190 207 251 295 336 373 428 182 200 216 267 317 363 421 485 518 199 215 270 322 380 436 502 562
228 298 329 358 435 514 587 652 761 287 317 343 425 504 580 675 778 835 287 311 393 471 555 639 736 827
69
127 166 183 198 241 283 323 357 416 177 195 210 259 307 352 409 471 503 194 209 262 313 370 423 488 546
222 291 321 349 424 500 571 633 751 283 313 338 419 497 572 665 767 824 283 307 388 464 548 630 726 815
70
122 160 176 190 231 271 309 342 404 172 189 204 252 299 342 398 458 489 188 203 255 305 359 411 474 530
Joist Designation 40LH08 40LH09 40LH10 40LH11 40LH12 40LH13 40LH14 40LH15 40LH16 44LH09 44LH10 44LH11 44LH12 44LH13 44LH14 44LH15 44LH16 44LH17 48LH10 48LH11 48LH12 48LH13 48LH14 48LH15 48LH16 48LH17
Depth (in.) 40 40 40 40 40 40 40 40 40 44 44 44 44 44 44 44 44 44 48 48 48 48 48 48 48 48
Approx. Wt. (plf) 16 21 21 22 25 30 35 36 42 19 21 22 25 30 31 36 42 47 21 22 25 29 32 36 42 47
217 282 313 340 413 487 556 616 730 279 308 333 413 490 564 656 756 812 279 303 382 458 540 621 716 804
71
117 153 169 183 222 260 297 328 387 167 184 199 245 291 333 387 445 475 183 197 248 296 349 400 461 516
211 276 305 332 402 475 542 599 710 275 304 329 407 483 556 647 746 801 275 299 377 451 533 612 706 793
72
112 147 162 176 213 250 285 315 371 162 179 193 238 283 324 376 433 462 178 192 241 288 340 389 448 501
206 269 297 323 392 463 528 583 691 272 300 325 402 477 549 639 737 790 271 295 372 445 525 604 696 782
73
108 141 156 169 205 241 273 302 356 158 174 188 232 275 315 366 421 450 173 187 235 280 331 379 436 488
201 263 290 315 382 451 515 567 673 265 293 317 393 466 534 623 719 780 268 291 367 439 518 596 687 771
74
104 136 150 163 197 231 263 290 342 152 168 181 224 265 302 352 405 438 169 182 228 273 322 368 425 475
196 256 283 308 373 440 502 552 655 259 286 310 383 454 520 608 701 769 264 287 362 433 511 588 678 761
75
100 131 144 157 189 223 252 279 329 146 162 175 215 254 291 339 390 426 164 177 222 266 313 359 414 462
192 250 276 300 364 429 490 538 638 253 279 302 374 444 506 593 684 759 261 283 357 428 505 580 669 751
76
97 126 139 151 182 214 243 268 316 141 155 168 207 246 279 326 375 415 160 172 217 259 305 349 403 450
187 244 269 293 355 419 478 524 622 247 272 295 365 433 493 579 668 750 257 279 353 422 498 573 660 742
77
93 122 134 145 176 207 233 258 304 136 150 162 200 236 268 314 362 405 156 168 211 252 297 341 393 439
183 239 262 286 346 409 466 511 606 242 266 289 356 423 481 565 652 732 254 276 348 417 492 566 652 732
78
90 118 129 140 169 199 225 248 292 131 144 157 192 228 259 303 348 390 152 164 206 246 290 332 383 428
178 233 255 279 338 399 455 498 591 236 260 282 347 413 469 551 637 715 251 272 344 412 486 559 644 723
79
86 113 124 135 163 192 216 239 282 127 139 151 185 220 249 292 336 376 148 160 201 240 283 324 373 417
174 228 249 273 330 390 444 486 576 231 254 276 339 404 457 537 622 699 248 269 340 407 480 552 636 714
80
83 109 119 130 157 185 209 230 271 122 134 146 179 212 240 281 324 363 145 156 196 234 276 316 364 407
226 249 269 331 395 446 524 608 683 246 266 336 402 475 545 629 706
81
118 130 140 172 205 231 271 313 351 141 152 191 228 269 308 355 397
221 243 264 323 386 436 512 594 667 241 260 329 393 464 533 615 690
82
114 125 136 166 198 223 261 302 338 136 147 185 221 260 298 343 383
216 238 258 315 377 425 500 580 652 236 255 322 384 454 521 601 675
83
110 121 131 160 191 215 252 291 327 132 142 179 213 251 287 331 371
211 233 252 308 369 415 488 568 638 231 249 315 376 444 510 588 660
84
106 117 127 155 185 207 243 282 316 127 137 173 206 243 278 320 358
207 228 247 300 361 406 476 555 624 226 244 308 368 434 499 576 646
85
103 113 123 149 179 200 234 272 305 123 133 167 199 234 269 310 346
202 223 242 293 353 396 466 543 610 221 239 301 360 425 488 563 632
86
99 110 119 144 173 193 227 263 295 119 129 161 193 227 260 299 335
198 218 236 287 346 387 455 531 597 217 234 295 353 416 478 551 619
87
96 106 115 139 167 187 219 255 285 116 125 156 187 220 252 289 324
194 214 232 280 338 379 445 520 584 212 229 289 345 407 468 540 606
88
93 103 111 134 161 181 211 246 276 112 120 151 180 212 244 280 314
208 225 283 338 399 458 528 593
89
108 117 147 175 206 236 271 304
204 220 277 332 390 448 518 581
90
105 113 142 170 199 228 263 294
200 216 272 325 383 439 507 569
91
102 110 138 164 193 221 255 285
196 212 266 318 375 430 497 558
92
99 106 133 159 187 214 247 276
192 208 261 312 367 422 487 547
93
96 103 129 154 181 208 239 268
188 204 256 306 360 413 477 536
94
93 100 126 150 176 201 232 260
185 200 251 300 353 405 468 525
95
90 97 122 145 171 195 225 252
Joist Designation 40LH08 40LH09 40LH10 40LH11 40LH12 40LH13 40LH14 40LH15 40LH16 44LH09 44LH10 44LH11 44LH12 44LH13 44LH14 44LH15 44LH16 44LH17 48LH10 48LH11 48LH12 48LH13 48LH14 48LH15 48LH16 48LH17
Depth (in.) 40 40 40 40 40 40 40 40 40 44 44 44 44 44 44 44 44 44 48 48 48 48 48 48 48 48
Approx. Wt. (plf) 16 21 21 22 25 30 35 36 42 19 21 22 25 30 31 36 42 47 21 22 25 29 32 36 42 47
181 196 246 294 346 397 459 515
96
87 94 118 141 165 189 218 245

You might also like