Professional Documents
Culture Documents
Solution Report For: Home My Test My Profile
Solution Report For: Home My Test My Profile
MY PROFILE Solution Report For ME : Demo Test
Represent whole test solution with correct and incorrect answers.
REPORTS
View Your Test Analysis
BUY PACKAGE
NEWS
Q. No Question Status
Ask an Expert
Q.1 In the sentence given below, there are a set of blanks. Out of the choices given
below, pick out the option that can fill in blanks so that we get a meaningful
sentence:
The interest has ________ innovation related to several sectors of ________
pharmaceutical business and industry.
a. accepted, skeletal
b. insured, fateful
c. accelerated, burgeoning
d. restricted, grown
Q.2 A sentence has been split into 4 parts labeled as (a) to (d). One of the parts
has some error(s) which need/s to be corrected. Identify the part that has an
error.
a. A group of youngsters
b. has lend financial assistant
c. to the flood affected
d. residents of the village
Q.3 Out of the given options, identify the set which has the words bearing the same
relationship as in the given set:
Tehsil : District : State : Country
a. Block : Colony : Zone : City
b. Metropolitan : Megalopolis : Town : City
c. Province : District : State : Country
d. Madhya Pradesh : Maharashtra : Mumbai : Victoria Terminus
Attempt Incorrect Your Ans. d Correct Ans. a
FAQ? Have any doubt? Solution
Q.4 Johnny has bought two candles of equal length but different diameters. One of
the candles will burn up completely in 10 hours, while the other candle
requires 40% more time to burn up completely. If the candles are lit at the
same time, approximately how long will they burn before one of the candles is
twice the length of the other?
a. 7.8 hours
b. 6.4 hours
c. 5.6 hours
d. 6 hours
Q.5
What is the value of 2x + 3y if x + y = 6 and x2 + 3xy + 2y2 = 60?
Q.6 In this question, a given statement is followed by 2 courses of action: C1 and
C2. A course of action is an administrative step or decision taken for
improvement or as a follow up action with regard to the problem. Assume
everything stated in the statement as well as courses of action to be true even
if they seem to be in variance with the common prevalent practice. Mark your
answer as:
Option (a) if only course of action C1 follows
Option (b) if only course of action C2 follows
Option (c) if either C1 follows or C2 follows
Option (d) if both C1 as well as C2 follow
Statement: The state government has decided to make available food grains
and clothes to flood affected people.
C1: The flood affected people should be identified by the state government
machinery and adequate relief should be provided to them.
C2: The state government machinery should collect sufficient quantity of food
grains and clothes to help the flood affected people.
a. a
b. b
c. c
d. d
Q.7 A dice is constructed such that an outcome = even numbers 2, 4 or 6 showing
up is twice as likely to show as each of the odd numbers 1, 3, and 5. What are
the odds in favour of 6 showing up when the dice is rolled?
a. 2 to 1
b. 2 to 7
c. 1 to 2
d. 1 in 3
Q.8 Radhika rides her bike around a course which is in the shape of an equilateral
triangle. She covers the first arm at an average speed of 10 Km per hour while
her average to cover the 2nd arm is 15 Km per hour. She covers the final leg of
her journey to reach the starting point at an average speed of 20 Km per hour.
What is the average speed of Radhika during the entire ride?
a. is less than 13 Km per hour.
b. is at least 13 but less than 14 Km per hour.
c. is at least 14 but less than 15 Km per hour.
d. is at least 15 Km per hour.
Q.9 Pipe A and Pipe B can fill an empty cistern in 12 and 15 hours respectively.
There is hole in the bottom of the cistern which can empty the filled up cistern
in 90 hours. At 9 AM, pipe B is opened to start the filling up of the empty
cistern. After 3 hours, pipe A is also opened, at what time will the cistern get
filled up?
a. 5:00 PM
b. 5:30 PM
c. 5:45 PM
d. 6:00 PM
Q.10 Sarika and Trishali are asked to multiply a positive integer x by a positive
integer y and then add a positive integer z to the result. By mistake, Sarika
first multiplies x by z and then adds y, while Trishali by mistake adds x and y
and then multiplies by z. The correct answer was 29 whereas Sarika got 59
and Trishali got 80. If the sum of x, y and z is a multiple of 9, then the value of x
+ y + z is _____________.
Q.11 In a fillet welded joint, the weakest area of the weld is
a. toe
b. root
c. throat
d. face
Attempt Correct Correct Ans. c
FAQ? Have any doubt? Solution
Q.12 A big casting is to have a hole, to be produced by using a core of 10 cm
diameter and 200 cm long. The density ρmetal is 0.077 N/cm3 and density ρcore
is 0.0165 N/cm3 . What is the upward force acting on the core prints?
a. 200.5 N
b. 1100.62 N
c. 950.33 N
d. 350.32 N
Q.13 If n = 0.5 and C = 300 for the cutting speed and the tool life relation, when
cutting speed is reduced by 25%, the tool life will be increased by
a. 100%
b. 95%
c. 78%
d. 50%
Q.14 Primary objective of full annealing is to
a. Increase toughness and yield point
b. Reduce ductility and resilience
c. Remove foreign impurities and improve surface finish
d. Increase ductility and mechanability
Q.15 Nozzle angle of 50% reaction tubine is 20°. Maximum possible efficiency of the
turbine is
a. 90.75
b. 91.75
c. 92.75
d. 93.75
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.16 If the optimistic time, most likely time and pessimistic time for an activity A
are 4, 6 and 8 days respectively and for an activity B are 5, 5.5 and 9 days
respectively, then
a. expected time of an activity A is greater than the expected time of an activity B
b. expected time of an activity B is greater than the expected time of an activity A
c. expected time of both activities A and B are the same
d. None of the above
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.17
The ratio of , i.e. the ratio of section modulus of two beams having the
same crosssectional area if the first beam has a solid circular crosssection
with diameter d1 and section modulus Z1 and the second beam has a hollow
circular crosssection of outer diameter ‘d2 ’ is
a.
b.
c.
d.
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.18 Figure shows a steel beam AB 1800 mm long fixed at A and supported at the
other end B, by the lower end of a vertical 6 mm diameter steel rod 900 mm
long. The beam carries a uniformly distributed load of 2500 N/m. The moment
a. 1.508 kN
b. 1.687 kN
c. 1.418 kN
d. 1.708 kN
Not Attempt Correct Ans. a
FAQ? Have any doubt? Solution
Q.19 This reversible cycle consist of constant volume heat addition, reversible
adiabatic expansion and constant pressure heat rejection
a. Otto cycle
b. Lenoir cycle
c. Atkinson cycle
d. Brayton cycle
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.20 If the force transmitted to its foundation by a machine shall not exceed one
fortieth of the applied force, then the frequency ratio when the damping is
neglected is
a. 2.316
b. 4.302
c. 6.403
d. 8.904
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.21
Helium gas is compressed from 27°C and 3.50 m3 /kg to 0.775 m3 /kg in a
reversible and adiabatic manner. The temperature of helium after
compression is [Take γHe = 1.667]
a. 74°C
b. 122°C
c. 547°C
d. 709°C
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.22 What are maximum possible effectivness for parallel flow and counter flow
heat exchangers?
a. 30%, 40%
b. 50%, 100%
c. 50%, 70%
d. 70%, 50%
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.23 Consider two infinitely long black body concentric cylinders with a diameter
ratio D2 /D1 = 5. The shape factor for the outer cylinder with itself will be
a.
b.
c.
d.
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.24
For which values of the constants ‘b’ and ‘c’ is a vector a linear
combination of
a. 9, 6
b. 6, 9
c. 6, 6
d. 9, 9
Not Attempt Correct Ans. a
FAQ? Have any doubt? Solution
Q.25 A spherical iron ball 10 cm in radius is coated with a layer of ice of uniform
thickness that melts at a rate of 50 cm3 /min. When the thickness of ice is 5
cm, then the rate at which the thickness of ice decreases is
a.
b.
c.
d.
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.26 A cup of 50 mm diameter and 20 mm height is to be produced by drawing from
a 1.5 mm thick steel metal. Assume ultimate strength of the sheet metal to be
650 MPa. The maximum drawing force is ________MN.
Q.27 An ice making plant produces ice at atmospheric pressure and at 0°C from
water. The mean temperature of cooling water circulating through the
condenser of the refrigerating machine is 18°C. The minimum electrical work
in kWh required to produce 1 tonne of ice is ___________ kWh.
[The enthalpy of fusion of ice at atmospheric pressure is 333.5 kJ/kg].
Q.28 If the completion time for a particular project is 20 weeks and its earliest
expected time is 22 weeks, then the slack time for the project is ________
weeks.
Not Attempt Correct Ans. 2
FAQ? Have any doubt? Solution
Q.29 A bolt is subjected to an axial pull of 8 kN and a transverse shear force of 3
kN. The area of the bolt based on maximum shear stress theory is
______________ mm2 .
(Take Elastic limit in simple tension equal to 270 N/mm2 , factor of safety = 3)
Q.30 The gross head available to a hydraulic power plant is 100 m. The utilised head
in the runner of the hydraulic turbine is 72 m. If the hydraulic efficiency of the
turbine is 90%, the pipe friction head is estimated to be _____________ m.
Q.31 Air flows steadily in a pipe at 300 kPa, 77°C and 25 m/s at a rate of 18 kg/min.
The diameter of the pipe will be ___________ cm.
Q.32
The ratio of radius of the Earth’s orbit to that of the sun is 216. The solar
insolation on the Earth is 1.4 kW/m2 . If the sun is assumed to be ideal radiator,
then surface temperature of the sun is _______ K.
Q.33 The 10 kg block is moving to the right at 6 m/s when the 360 N/m spring is
unstretched. If the horizontal plane is frictionless, the block will first come to
rest in _________m.
Q.34 The area enclosed between the curve y = loge (x + e) and the positive
coordinate axis is ________.
Not Attempt Correct Ans. 1
FAQ? Have any doubt? Solution
Q.35
The value of , where C is the = 1 is _________.
Not Attempt Correct Ans. 1
FAQ? Have any doubt? Solution
Q.36 Consider the following assumptions pertaining to ROLLING process:
P: The rolls are straight and rigid cylinders.
Q: Rolling strip is subjected to plane stress condition.
R: Coefficient of friction is constant over the entire roll job interface.
S: Yield stress remains constant for the entire operation.
Which of the above statements are correct?
a. P, Q and R
b. P, Q and S
c. P, R and S
d. Q, R and S
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.37 Aluminimum billet of 30 mm diameter is extruded with an extrusion ratio 16.
The ideal extrusion pressure, if the effective flow stress in compression is 250
MPa, is
a. 575 MPa
b. 635 MPa
c. 665 MPa
d. 693 MPa
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.38 What is the NC code for following cutting tool movement?
a. N01 G02 X7 Y2 I0.05 J2.0
b. N01 G01 X7 Y2 I0.0 J2.0 F6
c. N01 G03 X7 Y2 I0.0 J2.0
d. N01 G02 X7 Y2 I0.0 J2.0 F6
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.39 A through hole of diameter 30 mm has to be drilled in a lathe in a rectangular
plate of size 500 × 400 × 50 mm. Drills of diameter 10 mm, 20 mm and 30 mm
are available. Assuming that the cutting speed is 10 m/min. and the feed for
drill is 0.2 mm/rev., calculate the drilling time. Neglect approach and over
travel. Maximum material cut at a time cannot exceed 10 mm.
a. 1.6 min
b. 48 min.
c. 16 min.
d. 5.37 min.
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.40 What is the interplanar spacing between (200), (220), (111) planes in an FCC
crystal of atomic radius 1.246 Å?
a. d(200) = 1.762 Å, d(220) = 1.24 Å and d(111) = 2.034 Å
b. d(200) = 1.24 Å, d(220) = 1.762 Å and d(111) = 2.034 Å
c. d(200) = 2.034 Å, d(220) = 1.24 Å and d(111) = 1.762 Å
d. d(200) = 2.5 Å, d(220) = 4.2 Å and d(111) = 2.6 Å
Not Attempt Correct Ans. a
FAQ? Have any doubt? Solution
Q.41 For the network shown in the given figure, the earliest expected completion
time of the project is
a. 26 days
b. 27 days
c. 30 days
d. Indeterminable
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.42 Find the ratio of the values of torque that can be transmitted by the hollow
shaft to solid shaft of the same material, same length and equal weight. If one
is a solid shaft and the other a hollow one with the inside diameter being half of
the outside diameter
a. 1.44
b. 0.69
c. 2.20
d. 2.75
Not Attempt Correct Ans. a
FAQ? Have any doubt? Solution
Q.43 A symmetrical stationary vane experiences a force F of 100 N as shown in the
figure below, when the mass flow rate of water over the vane is 5 kg/s with a
velocity ‘v’ of 20 m/s without friction.
The angle α of the vane is
a. zero
b. 30°
c. 45°
d. 60°
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.44 The eye of a tornado has a radius of 40 m. If the maximum wind velocity is 50
m/s, the velocity at a distance of 80 m radius is
a. 100 m/s
b. 2500 m/s
c. 31.25 m/s
d. 25 m/s
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.45 A diesel engine has a compression ratio of 14 and cut off takes place at 6% of
the stroke. What is the value of cut off ratio ?
a. 1.25
b. 2
c. 2.15
d. 1.78
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.46 How many instantaneous centre(s) is/are located along fixed surface on which
the mechanisms rolls?
a. 2
b. 1
c. 3
d. None of these
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.47 Air enters a compressor at 1 bar, 30°C which is also the state of the
environment air leaves at 3.5 bar, 141°C and 90 m/s. Neglect inlet velocity and
P.E. effect. What will be the isothermal work?
a.
b.
c.
d.
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.48 For the following figure
What is the required value of “n”?
a.
b.
c. γ
d.
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.49 The filament of a 75 W light bulb may be considered a black body radiating into
a black enclosure at 70°C. The filament diameter is 0.10 mm and length is 50
mm. Considering radiation, the filament temperature will be
a. 2756 °C
b. 2566 °C
c. 5512 °C
d. 2120 °C
Not Attempt Correct Ans. a
FAQ? Have any doubt? Solution
Which of the following statement must be true?
a. f (x) has exactly one maxima.
b. f (x) has exactly one minima.
c. f (x) has one minima and one maxima.
d. Can’t be determined.
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.51 A 3 × 3 matrix is defined as
is found to be singular. Which of the following statement is true.
a. x, y & z are in harmonic progression
b. x, y & z are in arithmetic progression
c. either x = y or y = z or z = x
d. x, y & z are in geometric progression
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.52 A 50 mm diameter shaft is subjected to a pure torsion which induces a shear
stress at 70 N/mm2 . The yield strength of the material at the shaft is 440
N/mm2 . Then the ratio of factor at safety obtained by the maximum energy
theory to that of maximum shear stress theory is ________.
Q.53 When milling a shaft of 20 mm wide, 10 cm long with a rectangular plate of 10
cm × 20 cm, if cutting conditions are:
Cutting speed = 60 m/min,
Diameter of end mill = 20 mm,
Number of flute teeth = 8,
feed = 0.01 mm/tooth
Depth of cut = 3 mm
Then the milling cutter feed rate is ________ mm/min.
Q.54 A workpiece of 30 cm diameter is being turned on a lathe and the tangential
force on the cutting tool is estimated to be 100 N. When the turning operation
is executed for 10 minutes, the increase in the internal energy of the
workpiece works out 125 kJ. If workpiece turns at 180 rev/min, then the heat
transfer from the workpiece is _________ kJ.
The ratio of Brayton cycle efficiency corresponding to maximum work done
and carnot cycle efficiency is ________.
Q.56 Consider the following activity i – j of a certain network
Then the value of
Not Attempt Correct Ans. 1
FAQ? Have any doubt? Solution
Q.57 A metal rod 2.4 m long is placed between and perpendicular to two vertical
walls 2.43 m apart as shown in figure. The temperature of the rod is raised
until the rod is fixed between the walls and has a compressive stress of 21
MN/m2 . The rod is restrained from bending. The rise in temperature is
Q.58
A velocity potential for a twodimensional flow is given by φ = (x2 – y2 ) + 3xy.
Then the flow rate between the streamlines passing through points (1, 1) and
(1, 2) is __________ units.
Q.59 The torque developed by an engine is given by the following equation:
T = 14250 + 2200 sin 2θ – 1800 cos2θ
where T is the torque in Nm and θ is the crank angle from the inner dead
centre position. The resisting torque of the machine is constant throughout the
work cycle. The energy output from flywheel is _________kJ.
Q.60 A cam that is designed for cycloidal motion drives a flatfaced follower. During
the rise, the follower displaces 1 cm for 180° of cam rotation. If the cam
angular velocity is constant at 100 rpm the displacement of the follower at a
cam angle of 60°, will be _________ mm.
Q.61 A heat engine receiving heat 100 kJ from a thermal energy reservoir at a
temperature of 200°C and producing work ‘w’, and rejecting heat to another
T.E.R. at a temperature of 30°C. During the heat interaction it is found that
second law efficiency is 80%. The amount of work produced by the engine is
__________ kJ.
Q.62 Hot water flows with a velocity of 0.2 m/s in a 200 mm long, 0.2 m diameter
pipe. Heat lost from the pipe outer wall is uniform and equal to 430 kW/m2 . If
the inlet water temperature is 80°C, Cp(water) = 4.2 kJ/kgK and density of
water = 1000 kg/m3 , water temperature at the exit will be _____________K.
[Neglect effect of pipe wall thickness]
Q.63 A bullet of mass 1 kg if fired with a velocity of u m/s from a gun of mass 10 kg.
The ratio of kinetic energies of bullet and gun is ______________.
Not Attempt Correct Ans. 10
FAQ? Have any doubt? Solution
Q.64 Three companies X, Y and Z supplies computers to a university. The
percentage of computer supplied by them and the probability of those being
defective are tabulated below.
Given that the computer is defective, the probability that is was supplied by Y
is ___________.
Q.65 A horse runs along a circle with a speed of 20 km/hour. A lantern is at the
centre of the circle. A fence is along the tangent to the circle at the point at
which horse starts. The speed with which the shadow of the horse moves
along the fence at the moment when it has covered 1/8th part of the circle is
___________ km/hour.
Not Attempt Correct Ans. 40
FAQ? Have any doubt? Solution