CNC SYSTEMS
OSP-U100M
OSP-U10M
MX-V SERIES
MAINTENANCE MANUAL
(1st Edition)
Pub. No. 4194-E (ME34-040-R1) May 1998
OKUMAME00-001-R1 P-())
SAFETY PRECAUTIONS
SAFETY PRECAUTIONS
The machine is equipped with safety devices which serve to protect personnel and the machine itself
from hazards arising from unforeseen accidents, However, operators must not rely exclusively on these
safety devices: they must also become fully familiar with the safety guidelines presented below to ensure
accident-tree operation.
This instruction manual and the warning signs attached to the machine cover only those hazards which
(Okuma can predict. Be aware that they do not cover all possible hazards.
Precautions Relating to Machine Installation
(1) _ Install the machine at a site where the following conditions (the conditions for achievement of
the guaranteed accuracy) apply.
- Ambient temperature: 17 to 25°C.
+ Ambient humicity: 40% 10 75% at 20°C (no condensation)
- Site not subject to direct sunlight or excessive vibration; environment as free of dust, aci
corrosive gases, and salt spray as possible.
(2) Prepare a primary power supply that complies with the following requirements.
= Voltage: 200 V
~ Voltage fluctuation: 10% max.
- Power supply frequency: 50/60 Hz
- Do not draw the primary power supply from a distribution panel that also supplies a major noise
source (for example an electric welder or electric discharge machine) since this could cause
maifunction of the CNC unit.
- Ifpossible connect the machine to a ground not used by any other equipment. Ifthere is no choice
but to use 2 common ground, the other equipment must not generate a large amount of noise
(such as an electric welder or electric discharge machine).
(3) Installation Environment
Observe the following points when installing the control enclosure.
+ Make sure that the CNC unit wil not be subject fo direct sunlight.
~ Make sure that the control enclosure will not be splashed with chips, water, or ol
= Make sure that the control enclosure and operation panel are not subject to excessive vibrations
or shook.
- The permissible ambient temperature range for the control enclosure is 0 to 40°C.
- The permissible ambient humidity range for the control enclosure is 30 to 95% (no condensation)
- The maximum altitude at which the control enclosure can be used is 1000 m (3281 ft.).ME00-001-R1 P-(i)
SAFETY PRECAUTIONS
Points to Check before Turning on the Power
(1) Close all the doors of the control enclosure and ‘operation panel to prevent the entry of water,
chips, and dust.
(2) Make absolutely sure that there is nobody near the moving parts of the machine, and that there
are no obstacles around the machine, before starting machine operation
(3) When turning on the power, turn on the main power disconnect switch first, then the CONTROL
ON switch on the operation panel.
Precautions Relating to Operation
(1) After turning on the power, carry out inspection and adjustment in accordance with the daily
inspection procedure described in this instruction manual,
(2) Use tools whose dimensions and type are appropriate for the work undertaken and the machine
specifications. Do not use badly worn tools since they can cause accidents.
(8) _Donot for any reason touch the spindle or tool while spindle indexing is in progress since the
spindle could rotate: this is dangerous.
(4) Check that the workpiece and tool are properly secured,
(6) Never touch a workpiece or tool while itis rotating: this is extremely dangerous.
(8) Donot remove chips by hand while machining is in progress since this is dangerous. Always
stop the machine first, then remove the chips with a brush or broom,
(7) Donot operate the machine with any of the safety devices removed. Do not operate the
‘machine with any of the covers removed unless it is necessary to do so,
(®) Always stop the machine before mounting or removing a tool
(®) Donot approach or touch any moving part of the machine while it is operating,
(10) Donot touch any switch or button with wet hands. This is extremely dangerous,
(14) Before using any switch or button on the operation panel, check that it is the one intended.