rat hp
Or
H
.
i
i
UDC 621.883.083 DEUTSCHE NORM November 1982
Wrench and socket openings
‘Schlisselweiten fir Schreubenschlisel ‘Supersedes March 1976 edition
{In keeping with current practice in standards published by the International Organization for Standardization (ISO),
{comma has been used throughout as the decimal marker.
For connection with international Standard 1SO 681 — 1983 published by the International Organization for Stand:
ardization (ISO), see Explanatory notes
Dimensions in mem
1 Field of application
This standard applies to all non-adjustable wrenches which are intended to grip the soraw head or the nut from the outside.
2 Dimension, designation
Ls. s
Designation of an opening having the nominal dimension s= 18 mm (SW 18), Sax complying with series 1 (1)
Opening DIN 475 — SW 18-1
Table,
‘Across flats (SW) ‘Across flats (SW)
Nominal | min, | mex Nominal min. oe
dimension | Series 1_| Series 21) dimension Series 1 | "Series 21)
2 202 2,08 23° 23.26 | 23.46 _|
24" 24,46
25
26°
_ 3,18,
10,24
1124
12,30
13,30
14,35
15,35
16,35
17,40 |—
18,40 7
19,46
19,06 .
20,06 20,46 700 * a
21° 21,06 21,46, 105 * 106.40,
22 22,06 722.46, 10° K 111,40
1) See page 2
Continued on page 2
‘Sen vovnn Gb Bevin 30, as azine sleigh for German Sandurds (OW Normen) DIN 475 Part 2 Engl. Price group 6Page 2 DIN 475 Part 2
Table, [eontinued)
Aeros fats SH) Aerossats SW)
Nominal jin Nominal | min i
dimension Series 2") dimension Series 1 ‘Serias 21)
115" 115,20 116,40 270 270,30 271,50,
[z0= [170,20 12140 "260 [280,90 | 281 50
30° | ta020 | 131,40 290 290,30 291,50
[135° 135,20 736,40_| ‘300 300,40 | 301.80 |
[145 * 145,20 146,40 [310 310,40 311,80
150" | 16028 329 | 3200 | 321,80,
ae5* 15528 0 | 3040 | 331,80
tes* | 165.25 340 | e040 | 341.80
[ova | 7025 350 | 360.40 | 351.80,
175°) 178.25 35 | 365.40” | 256.00
{180° 180,25 | (380 380,40 381,80 -
1657 | 105,25 395 | 306.40 | 39680
1907 | 190.25 a0 [#1050 | 412,10
200 * 200,25, ~ 425 425,50 427,10
“2107 210,25 440 440,50, 442,10
729 | 20:30] 55 [455,50 [467.10
230 | 230,30 470 470,50 472,10
736 | 795,30 aa | #9050 | 482,10,
[aus [248,30 | 705 [29550 | 097.10
255 255,30, [510 510,50 512,10
965 [20500 sas | 825.80 | 627.10
The widths across flats marked with an asterisk * comply with international standards, see also Explanatory notes.
Facer ironly oplcale to closed frged wrenches which have nt been finshed by chip removal
Standard referred to
1§0 691-1983 Wrench and socket openings - Metric series ~ Tolerances for general use
Previous editions
DIN 475: 12.21, 01.43xx; _ DIN 475 Part 1: 05.20, 04.28;
DIN 478 Part 2: 01.24, 01.42, 03.57, 06.63, 10.64, 04.71, 04.76
Amendments
Compared with the April 1976 edition, the following amendments have been made
4) Width across flats 34 (SW 34) has been included for the first tim
) The standard hes been revised editorially see also Explanatory notes.
Explanatory notes
This standard conforms to Standard ISO 691 ~ 1981 published by the Internetional Organization for Standardization
(1SO} as regards the tolerances for wrench and socket openings marked with an asterisk
The ISO Standard is obtainable from DIN Deutsches Institut fir Normung e.V., Berlin
{180 60! the widths across flats 6,9, 12, 14, 17, 19, 20, 2, 23, 25, 26, 28 and 32 are given in brackets as posibig
aeeecalate values, The widths across flats marked with an asterisk except for the intermediate values and dimensions
175 and 190 agree with the widths across flats for hoxagon head bolts and sorews specified in ISO 272 ~ 1979.
International Patent Classification
8.25 B 13/08