pe W 16 IR
Determination ofthe load resistance of
Introduction
“This Standard gives the principles of determining the lal resistance of plas.
‘The principles of determining the load resistance of glass are based on the sirecturl
[Eurocode EN 1990: Basis of structural design. The acions are determined in accordance
with the structural Eurocode series EN 1991: Basis of structural design ~ Actions on
structures, including the National annexes.
1 Scope
“This Standard gives the principles of determining the load resistance of glass. It gives:
‘the general method of calculation, and
‘determination of load resistance by testing for any application,
‘This Standard does not determine suitability for purpose. Resistance to applied loads is
only ne par ofthe design process, which may also need 1 tak into acount:
* eavioamental factors (@. sound insulation, thermal properties),
safety characteristics (e.g. fre performance, breakage characteristics in relation to
human safety, security)
2 Normative references
“The following referenced documents are indispensable forthe application ofthis docunent.
For dated references, only the edition cited applies. For undated references, the latest
ceton ofthe referenced document (including any amendments) applies.
[Ea ‘Gass in balding ~ Delerination of laninous and solar characterises
of glaring
ENS iiss in bllding - Base sod ime siete glass prods
ENSTDT ‘Gass in building - Basic soda lime silicate glass products ~ Par
Definitions and general physical and mechanical properties
ENG “Glas in building - Determination of thermal tansmitance (U value) =
Calculation method
EN TO Glass in building - Mirrors fom silver coaied oat glass Tor iaewmal
EN 1056 | Glass a building ~ Coated glass
EN 1279 ‘Gass in building sulting lass units
"EN 1748:1 | Glas in building - Basic borosiieate glass products
EN T748-1-1 [Glass in building ~ Basic boroslicae glass products ~ Pat T
Definitions and general physical and mechanical properties
ENTHE2 | Glass in building - Basic glass ceramies productsfENTaaT—]
]Giass in building - Basie glass ceramics products - Part I= Definitions
and general physical and mechanical properties
EN 1863 Giass in building - Heat strengthened soda lime siete glass
TEN 1863-1 lass in building - Heat strengthened soda lime slieate glass ~ Part:
Definition and description
TEN 1990;3000 | Euracode = Basie of srvesural design
EN 1991, ‘Actions om sivcures|
[EN 1991-14 | Wind actions.
EN 1997 ‘Geotechnical dex
EN 1998 Design of structures for eanhguake
EN 12150, ‘Gass in building - Thermally toughened soda Time silicate salty glass
EN 12150-1 [Glass in building - Thermally toughened sods lime silicate safety glass ~
Part 1: Definition and description
ENISS7 Giass in building - Chemically strengihened soda Tine scare glass
'EN 123371 | Glass in building - Chemically strengthened soda lime silicate gas =
Part 1: Definition and description
[EN 180 12543 —| Glas in building - Laminated and laminated iy glass
EN 180 125431 [Glass in building ~ Laminated and faminated safeyy glass ~ Part 1
Definitions and description of component parts
ENO Glass in building - Thermally toughened borosilicate safey glass
EN 130241 [Glass in building - Thermally toughened boroslicae safety gas
Part 1: Definition and description
ENA Glass in building - Basic alkaline earth Scale glass prodios
EN 141781 | Gass in building - Basic alkaline earth sia glass products ~ Par
efiniions and general physical and mechanical properties
EN TAT ‘Glass in building - Heat soaked thermally toughened soda line cate
safety glass
EN T4179 | Gass in bulding ~ Heat soaked thermally Toughened soda Time sca
safety glass - Part 1: Definition and description
EN T4321 | Glass in building - Thermally toughened alkaline ean slate wey
lass
EN 143211 | Glass in building ~ Thermally toughened alkaline ath oilcae saleiy
las - Part I: Definition and description |
EN Ta9 Glass in building ~ Laminated glass and laminated safety glass —
Evaluation of conformity/Product Standard
3 Terms and def
ions
For the purposes ofthis document, the following terms and definitions apply
3.1 annealed glass: Glass which has been treated during manufacture to minimise the
residual sess in the glass, allowing itt be cut by scoring and snapping.
[NOTE Fxamples are oat glass, drawn sheet las, patterned glass and wired gla.3.2 effective thickness (of laminated glass): A thickness calculated for laminated glass
‘hich, when used in place ofthe pass thickness in an engineering formula, wil result in 8
Teasonably accurate determination of the deflection of and /o stress in the laminated glass.
133 prestressed pass: Glass which has been subjected oa strengthening treatment, by heat
‘or chemicals, which induces a compressive surface stress into the whole surface ofthe
tlss, balanced by a tensile sre within the body ofthe glass.
NOTE Examples are thermally roughened safety glass, heat strengthened glass and
chemically stengthened gas.
‘34 main structure: The teams, the columns, the floor forming the main strscture of the
building (se figure 1).
[NOTE The main strctre is commonly class of consequence CC2 or CC3.
e-
@®-
@
Key
main structure
2 secondary structure
3 infil pane
Figure 1 — Identifiation of structure
[NOTE Elements of main structure are stritural in so far as they carry themselves and
secondary structures, and, in case of failure, endanger the fundamental stability of the
building. The main structural elements must have a safety and a ribilty appropriate 10
their design use and larger factor of safety than the one applicable to the secondary