Professional Documents
Culture Documents
'N'
FLUSH FOR
have been designed to minimise process fluid emissions when DUAL SEALS
selected, fitted and used correctly.
If the process fluid is toxic or hazardous, appropriate
Ø D26
precautions must be taken to contain any emissions.
Never burn any of the rubber or plastic parts of the
mechanical seal. Toxic fumes may be generated.
Attention: The machinery operating conditions must not exceed
Ø D1 SHAFT
Ø D4 BORE
the published operating limits of the mechanical seal.
Attention: Take care when handling the mechanical seal as it
contains precision lapped parts.
Note: Operating limits and all dimensions can be found at:
www.johncrane.com C heck ing T he Machine
The operating limits will depend on the
materials used. Fig 2 A Seal Size
B
E
0.2-0.5 μm Ra
Ta b l e 1 S o c ke t S e t S c r e w T i g h t e n i n g 8-20 μinch Ra
To r q u e – A l l E xc e p t 5 6 0 0 S e r i e s
C 1.6-3.2 μm
Ra 63-125 μinch Ra
Screw Torque Screw Torque
D 1 mm/0.040 inch
Size (Lubricated) Size (Lubricated)
Nm/lbf·ft Nm/lbf·ft E 1.5 mm/0.060 inch
Ta b l e 2 S o c ke t S e t S c r e w T i g h t e n i n g
To r q u e – 5 6 0 0 S e r i e s O n l y
1 2 3 4
Seal Size Screw Torque Screw Torque
Code Size Nm/lbf·ftt Size Nm/lbf·ft Squareness of shaft Concentricity seal Shaft runout Shaft end play
to seal chamber face chamber bore to shaft
Up to 0480 M5 3.5/2.6 #10-24 UNC 3/2.2
0500 to 1206 M6 7/5.2 1/4-20 UNC 8/5.9 0.001 mm/mm diameter <0.13 mm FIM <0.05 mm FM <0.13 mm FIM
1250 & above M8 15/11.1 5/16-18 UNC 15/11.1 0.001 inch/inch diameter <0.005 inch/FIM <0.002 inch/FIM <0.005 inch/FIM
Return
to suction
By-pass from
discharge
Flush outlet
Flush
Flush
Quench/Drain Flush outlet
Quench/Drain
Quench Quench
Drain Drain
TI
Flush inlet drain, plugged Flush outlet
shown for CW
Temperature shaft rotation
Pumping indicator
ring Quench/Drain Quench
10 13 12 2 1 3 4 5 6 7 8 9 14 15 11
25°
‘D’ – Drain `I’ – Buffer/Barrier Inlet As supplied, these gland plates have metal plugs fitted GLAND
2
`Q’ – Quench `V’ – Vent Inch sizes – see relevant clockwise ANSI pump illustrations BLANK PADS
3
All standard pipework connections are tapped 3/8 inch NPT. mm sizes – see relevant clockwise DIN pump illustrations
Special 5610 and 5615 seals may use a dual seal gland plate with a Remaining connections are fitted with temporary plastic blanking plugs that cannot
single seal, for conical seal chambers. All ports are plugged. Use no flush. hold pressure. All plugs should be left in place until connection of the pipework. Plastic
A quench bush allows a quench by piping ports 1 and 3 as shown for plugs must be replaced with metal plugs or appropriate fittings.
“Single Seal with Quench”. NOTE: Ensure the seal is correctly piped & plugged as shown in the relevant illustration
Seal sizes above 75 mm/3.000 inch use a fully machined gland plate for the particular application. Due to the wide variety of design of pumps & other
with radial drillings that allow bi-directional shaft rotation. Pipework machines the piping illustrations may not be valid in all cases. Consult John Crane if an
connections are tapped 1/2 inch NPT. alternative piping arrangement is required.
CLOCKWISE CLOCKWISE
NO OPTION AVAILABLE
CLOCKWISE ROTATION
ROTATION ROTATION
PLUGGED
PLUGGED
NOT NOT
NOT
NOT NOT NOT DRAIN DRILLED
DRILLED PLUGGED
DRILLED
DRILLED
DRILLED
DRILLED DRAIN PLUGGED
NOT
NOT NOT DRILLEDNOT PLUGGED OUTLET
DRILLEDDRILLED DRILLED PLUGGED OUTLET
FLUSH
FLUSH
FLUSH
FLUSH
INLET
INLET INLET
INLET
NOT NOT
DRILLED DRAIN
DRAIN PLUGGED
PLUGGED PLUGGED
PLUGGED
DRILLED
Sizes To 75 mm/3 inch DIN Pumps Counter Clockwise Rotation Sizes To 75 mm /3 inch ANSI Pumps Counter Clockwise Rotation
Single Seal Single Seal Dual Seal Single Seal with Flush Single Seal Dual Seal
with Flush with Quench with Quench
NOT
DRILLED
NOT
QUENCH OUTLET
NOT OUTLET DRILLED QUENCH OUTLET
FLUSH FLUSH
FLUSH
PLUGGED
OUTLET
NOT
DRILLED
NOT FLUSH
QUENCH
QUENCH
PLUGGED
DRILLED NOT
DRILLED
DRILLED PLUGGED
PLUGGED
NOT
DRILLED
COUNTER COUNTER COUNTER FLUSH
FLUSH COUNTER FLUSH
FLUSH COUNTER
NOT
DRILLED INLET COUNTER
CLOCKWISE CLOCKWISE CLOCKWISE CLOCKWISE CLOCKWISE
CLOCKWISE
ROTATION ROTATION ROTATION ROTATION ROTATION ROTATION
PLUGGED
NOT
NOT
DRILLED DRAIN
INLET
INLET PLUGGED
NOT NOT
DRILLED NOT
NOT
DRILLED DRILLED DRAIN PLUGGED NOT
arrangements.
7. For seals other than the 5600 series follow the installation guide on page 6.
TYPE
4610, 4620P, 5610, 5610Q, 5610P, 5610D, 5610VQ, 5611,
5611Q, 5615, 5615Q, 5620, 5620P, 5620D, 5620VP, 5620V,
5625, 5625P, EZ-1, FFET, SB1, SB1A, SB2, SB2A, SBW
5 valve manifold
Buffer [not illustrated]
outlet
2. For single seals on a vertical shaft the flush should be above the seal faces
to ensure self-venting.
Buffer
outlet Cooling water in 3. For dual seals on a horizontal shaft the barrier outlet should be at TDC to
Buffer liquid drain,
normally closed ensure self venting of the seal. If this is not practical then manually vent the
Buffer inlet seal if it is safe to do so. The seal chamber should be vented as described in
Note: Tangential porting
is uni-directional. Gland
Buffer inlet paragraph 1.
illustrated is for CCW Gland End View
Pumping ring ©2014 John Crane rotation from drive end. 4. For dual seals on a vertical shaft the barrier outlet should be above the upper
seal faces to ensure self-venting. The flush connection should be above the
level of the lower faces.
Plan 53A - Dual pressurized arrangement 5. For a thermosiphon system follow the piping layout in Fig 5. A pumping ring
is always recommended for use with a thermosiphon system.
Pressure source
Pressure transmitter
with local indicator Normally open
Note: A barrier fluid drain is
Orifice located on the low point of the
barrier inlet (not illustrated). Plan 52/53A
2 valve manifold Level gauge See Best Piping Practices.
N2 FOR P53A
Make-up barrier liquid fill, Piping layout VENT FOR P52
normally closed
Cooling coils
Barrier
outlet Cooling water in
FILL LINE
Barrier liquid drain,
Flush normally closed
(when NORMAL LIQUID LEVEL
Specified) Barrier inlet
Note: Tangential porting Barrier inlet LG
is uni-directional. Gland
illustrated is for CCW Gland End View
Pumping ring ©2014 John Crane rotation from drive end.
<=900mm
BARRIER/BUFFER
RETURN TO RESERVOIR
DPIT
305 TO 762mm
MECHANICAL
12 TO 30"
SEAL
Barrier inlet
DRAIN DRAIN VALVE
(RECOMMENDED - FURNISHED BY PURCHASER)
*SeaI cartridge is OD registered on the ** Seal cartridge is OD registered on the * Seal cartridge is OD registered on the
Turn Dia. of 4.125. Turn Dia. of 4.125. Turn Dia. of 4.125.
**SeaI cartridge is OD registered on the *** Seal cartridge is OD registered on the ** Seal cartridge is OD registered on the
Turn Dia. of 5.125. Turn Dia. of 5.125. Turn Dia. of 5.125.
4610, 4620P, 5610, 5610Q, 5610P, 5610D, 5610VQ, 5611,
5611Q, 5615, 5615Q, 5620, 5620P, 5620D, 5620VP, 5620V,
TYPE 5625, 5625P, EZ-1, FFET, SB1, SB1A, SB2, SB2A, SBW
*SeaI cartridge is OD registered on the Turn Dia.. of 4.125. ** Seal cartridge is OD registered on the Turn Dia. of 4.125.
**SeaI cartridge is OD registered on the Turn Dia. of 5.125. *** Seal cartridge is OD registered on the Turn Dia. of 5.125.
For your nearest John Crane facility, please contact one of the locations below.
If the products featured will be used in a potentially dangerous and/or
North America North America Europe Latin America Middle East & Africa Asia Pacific hazardous process, your John Crane representative should be consulted prior
Morton Grove, IL Houston, TX Slough, UK São Paulo, Brazil Dubai, United Arab Emirates Singapore to their selection and use. In the interest of continuous development, John
Tel: +1-847-967-2400 Tel: +1-713-944-6690 Tel: +44-1753-224000 Tel: +55-11-3371-2500 Tel: +971-481-27800 Tel: +65-6518-1800 Crane Companies reserve the right to alter designs and specifications without
Fax: +1-847-967-3915 Fax: +1-713-946-8552 Fax: +44-1753-224224 Fax: +55-11-3371-2599 Fax: +971-488-62830 Fax: +65-6518-1803 prior notice. It is dangerous to smoke while handling products made from
PTFE. Old and new PTFE products must not be incinerated.
©2016 John Crane Revised 08/16 www.johncrane.comI-IOMPCA/Eng