Professional Documents
Culture Documents
PRINTER
Contents
(一)Hardware installation.................................................................................................4
(二)Software installation...................................................................................................5
三、 Operation instructions....................................................................................................7
1
5. The printer's power plug, power cord, network cable must be in
good contact, strong, to avoid frequent activities in place, so as to
avoid accidental loss caused by damage to system equipment.
6. Avoid exposing the printer to flammable liquids, gases, and
aerosols. Doing so may cause fire or electric shock.
7. When the printer power switch is off, plug the printer power cord
into a standard-compliant power outlet.
8. Do not remove any covers or screws other than those specified in
the instruction manual to avoid danger of electric shock or laser
radiation.
9. Before starting the machine must take away the irrelevant items on
the machine to avoid paper clips, staples, or other small metal into
the machine.
Do not reach into the printer while the printer is working.
11. Do not move the print head by hand as this may damage the
printer.
12. Do not allow to damage, cut or modify the power cord. Do not
place heavy objects on the power cord or pull or bend the power cord
unnecessarily.
13. If any of the following conditions occur, immediately turn off the
power switch and unplug the power plug (grasp the plug instead of
the cable when unplugging the power). (1) A foreign object is spilled
into the unit. (2) Suspected that the unit needs repair or repair. (3)
The machine case is damaged.
14. Do not touch the part marked with the "hot surface" label. Doing
so may result in personal injury.
15. Do not burn spilled toner or used toner. Toner dust may burn
when exposed to flames.
Before moving the printer, unplug the power cord from the wall
outlet; be careful not to damage the power cord under the body.
16. Turn off the power after the work.
二、Product installation
(一)Hardware installation
1.Products include accessories as shown:
2
Accessories
*1-Machine *2-USB line *3-Power cable *4-USBKEY *5-U disk
2. First, connect the machine with the host computer through the
USB cable (Figure No. 2), then insert the USBKEY (Figure No. 4)
into the host computer, and then pour the clean water into the cooling
water bottle (pay attention to add pure water , The bottle shown in
Figure NO. 1), the last ( Figure NO. 3) connected to the device power.
Picture. 1
(二)Software installation
1.Copy the print control software from the U disk (Figure NO.5)
3
to your computer and open the file. Find "Well Print Exp"
Double-click to launch the app.
2.(1)Connect the machine, open the software, wait for reset
(as shown below) :
Picture.2
(3).Ultra prin t operation description of image editing software
Double-click "Ultra Print -Setup " to run sharp color image editing, layout,
output software installation package, click "Next" and "Install" button
according to the software installation wizard until the software is installed
successfully.
4
Ultra print operation description - P icture 5
三、Operation instructions
(一)Ultra print operation description of image editing software
( 1) Double-click "Ultra Print." Open "Ultra print image editing software"
Click the "New " button in the "File" button in the upper left corner. Then
click "import image " button in the "File" button to select the image, the
image into the canvas.
Picture.6
5
(2)Modify the picture size: Select the picture, click the
right mouse button, select the output size, modify the picture
output size.
Picture. 7
( 3 ) Rotate Image: Select the image, right-click " Rotate " to
set the rotation angle and image mode of the image.
Picture.8
( 4 ) Copy, Paste Multiple: When you want to copy multiple copies of a picture
at the same time, select an image and click “ ” button on the toolbar, then
6
click “ ”button to make multiple paste settings.
Picture.9
(5) Image alignment and spacing
Picture.10
( 6) Color Manager: When the user has changed a new material or a new ink
or no corresponding curve, the user can enter the color manager interface in the
"Tools" menu to modify the relevant information of the curve.
7
Picture.11
( 7 ) White ink settings: The user can click “Option” in the
“ Setup” menu to select the white ink output mode for image
printing.
8
Picture. 12
(8)S ample print: This function is for the convenience of you want to preview
the output of the canvas before the canvas output, custom canvas for the current
sample. Choose "Samples" from Edit menu.
Picture.13
Picture.14
9
(10) Print Sure and parameter selection: After setting, click " " , please
make sure that the image to be printed is within the canvas. Here you can set the
material, resolution, color mode, PASS number, port, matching the
corresponding curve, finally click "Print" to output the image.
Picture.15
* Note: The default output port is to print to the file, the output PRN will be saved to the
selected folder. You can use the printer control software to print this file.
(10) Printing Progress Status: If you find the setting error, you can click
"Cancel" to print.
10
Picture.16
1. Select the corresponding print task from the task selection interface
11
Picture.18
(4)Task properties:① PASS MODE ② REPEAT PRINT (TIMES)③ INK
LIMITED。Then you can click “OK”.
12
Picture.20
Picture.21
Double click you choice the picture.
13
Picture.22
Ⅱ、Print control
Picture.23
14
Picture.24
1、X-margin width
Do not check the Y-Margin, the car will not move vertically when
printing, print directly in the current position.
Check Y-Margin , the car will first return to the origin of the Y-Margin position,
and then set Y-Margin start printing.
Do not tick the color bar , print out the image is the implementation of the print
command area, there will be no color bar edge.
Check the color bar , print out the image is the implementation of the print
command area plus color bar, color bar will only appear in the image edge. (The
color bar width and distance to image will be specified in the parameter settings)
15
Not checked white ink printing, only four-color printing (KCMY). If you print
five colors (KCMY + W), the alert bar at the bottom of the software reports that
the number of color channels in the print file is greater than the number of color
channels that can actually be printed at the moment.
In the current mode you want to print four colors, you can use the following
operations: 1, in the PS do not do spot channel. 2, select the spot color when
drawing in PIR software. (So sharp figure, the color channel is colored, but the
actual number of colors is four colors).
Do not check the queue printing, print the implementation of the currently
selected task.
Check the queue printing, will queue the task one by one to execute print
commands.
6、Material thickness
7、Print speed
10、Bi-tuning
16
III. PARAMETERS
Picture.25
1、White-Ink setting
Picture.26
2、White-Ink setting:Bottom ,Top , spot , Bottom +light ,light + top , only
light , only white. Bottom and Top are divided into two times print.
Bottom : firstly print white ink and then print colorful ink.
Top : firstly print colorful ink then white ink.
Spot :white and color at the same time print , if do not click the white ink back to
print the case, out of ink first out of white ink and then out of ink, over again. If
click the white ink back to print the case, the car first vertical movement to the
end of the image and then hit the first ink out of ink and then out of white ink,
over again.
3、Clean option
17
Picture 27
Cleaning settings are the cleaning settings during printing. Do not check the case
of automatic cleaning, the print process does not perform automatic cleaning
command. In the case of automatic cleaning checked, the machine will be based
on the number of settings interval and cleaning mode to complete the cleaning
action. Cleaning mode select Flash jet, print the appropriate number of times,
the car will stop at the cleaning bit flash cleaning, flashing flash intensity
depending on the frequency of cleaning flashing may be. Cleaning mode select
cleaning, print the appropriate number of times, the car will stop cleaning bits
for cleaning, cleaning intensity depending on the cleaning time may be.
Color bar width:The actual width of the printed color bar, the distance
from the screen is the distance between the color bar and the screen,
the position of the color bar can be selected as the left side of the
figure, the right side of the figure, and the two sides of the image.
4、 Flash setting (Don’t set)
18
4.Other setting
Feed rate: The speed of vertical movement during printing. The corresponding
speed of each speed gear should be changed in the system maintenance
movement setting.
In the check the case of automatic white jump, when printing to a blank area, the
car will not be horizontal movement, only vertical movement, until the blank
area to finish.
When you do not check the mirror printing, the printed image is the same as the
original image. When you check the mirror printing, the printed image is the
opposite of the original image
19
V.Maintenance
1.Bias calibration
(1 offset desplazamiento Bi-Dir
(1)Color offset
20
Picture 26
(2)Other setting
21
(1)X-Moto Configuration
Picture.27
(2)Y-Moto Configuration
22
Picture.28
(3)Z-Moto Configuration
Picture 29
Estado muestra la altura del coche del día.
23
La longitud del jog se refiere a cada punto de ascenso y descenso, el automóvil
sube y baja el movimiento de distancia.
La velocidad de la elevación frontal debe ajustarse de acuerdo con el interruptor
DIP de la placa base. Si la velocidad es demasiado alta, el eje Z puede estar
atascado. (No profesionales no transferidos)
Cuando el automóvil se eleva a cierta distancia, puede establecer la altura actual
como el grosor del material haciendo clic en Establecer grosor del material. El
software restará automáticamente el valor de Desfase del grosor del material de
la altura actual y mostrará el valor resultante en el material del grosor del
control de impresión.
En la parte delantera de la orientación del automóvil, haga clic en el automóvil se
moverá automáticamente a cero eje Z (esta operación no se puede realizar en la
plataforma)
Haga clic para mover a la altura de impresión.
4 option Opción de limpieza (No establecido)
Picture.30
(1)Cartridge (Don’t set )
Picture.31
(2)Wiper (Don’t set )
24
Picture.32
5、Voltage setting
Picture.33
6.Basic setting
Picture. 34
25
四、Description of the printer operation button
Operating mode
The machine has a switch, It is switch of the printer.
Instruction of Led light tank : LED brightness adjusting button is 42 ; Water
temperature adjusting button is 10°; The led light tank should add pure water.
Place the print material at the origin position of the platform, adjust the height
of the printer to the higher position, and then retract the platform to the lower
limit position. Click the printer down button. When you hear the beep, the
printer height is adjusted to the appropriate printing position. The print can be
executed normally.
26
1. Issued a print order, the ink jet printer without any response
In fact, the printer without any response is just an illusion. In the normal use
of the cable is connected properly, the printer is not out of paper, the printer is
not responding, mainly because there are many tasks in the printer's print queue
in the waiting state, that is, the printer's cache has many tasks in the queue. If
the print command is issued at this time, the print cache can not accept the new
print job, and finally show the phenomenon is the printer without any response.
Solution: Restart the printer, so that the contents of the printer cache is
automatically lost can solve the problem of no response.
2. nozzle clogging:
Sprinkler plug is generally divided into a soft plug plug and rigid plug plug
two cases.
Soft plug is blocked for some reason caused the ink viscosity in the nozzle
becomes larger due to disconnection failure. The general use of original ink can
be restored after repeated cleaning.
Rigid plug plugging refers to the nozzle has a chemical coagulant or impurities
caused by the plug. This troubleshooting is difficult. You can first remove the
nozzle, soak it in the Epson special cleaning solution with anti-wash pressure
cleaning method for cleaning. After washing and then washed with pure water on
the nozzle cleaning fluid, can be used after drying. As long as the hard objects do
not cause damage to the nozzle electrode, cleaning nozzle can continue to use. I
suggest that in the face of rigid plug plug, the best professional maintenance
personnel to check the maintenance, so as not to deal with improper cause
greater failure.
In addition, the use of refilling cartridges are also prone to nozzle clogging
failure, mainly for the following two reasons. First, Epson ink jet printer's ultra-
fine filter design in the ink cartridge outlet, and the nozzle and the ink cartridge
ink port interface is no filter. When the user in the ink cartridge to the ink
cartridge in the reverse direction of the ink, it is easy to make the dust and
impurities into the ink inlet, resulting in the printer plug. Second, the chemical
nature of refilling ink with the original ink cartridges are not the same as the
residual ink, between the different ink slow chemical reaction, it is extremely
difficult to observe with the naked eye. If the ink stays in the nozzle and react,
will have a devastating impact on the nozzle.
3. Printer cleaning nozzle failure:
Printer cleaning nozzle on the printer nozzle to play a decisive role in
protection, but also caused the plug is one of the main factors. Sprinkler car back
to the position, to be cleaned by the pump nozzle on the weak suction of the
nozzle, the seal from the nozzle protection. In the printer installation of new ink
cartridges or nozzles are disconnected, the suction pump at the bottom of the
machine to pump through its nozzle, the higher the accuracy of its work better.
However, in actual use, due to the extension of time, dust and ink residue Epson
large format ink jet printer use requirements are relatively high, once the
operation is not properly or can not meet the printing conditions, the printer is
27
prone to failure. This part of the maintenance method is: the printer cover
removed, remove the car, with pure water inhaled needle wash, in particular, to
the mouth of gasket mounted in the full cleaning. Note When cleaning this
component, do not use ethanol or methanol, this will cause this component in the
embedded gasket dissolved deformation. In addition, the ink jet printer to try to
stay away from high temperature and dust and more working environment, to
ensure long-term normal use of the machine.
4. Detection of normal ink and print accuracy decreased significantly:
Ink jet printer nozzle if the normal use, no failure, and only 20 to 40 ink
cartridges life. If the printer's printing accuracy drops, even if the replacement
cartridge does not help, then the printer's nozzle needs to be replaced.
For newly purchased printers, if the print line is often not clear, the text
graphics skew, text graphics outside the border blurred, print out the ink control
synchronization accuracy is poor, indicating the quality of the cartridge problem,
you should immediately replace the new cartridge.
5. Walking car dislocation collision:
Epson ink jet travel car track is composed of two alloy copper sleeve and a
round steel shaft precision sliding to complete, walking car design is equipped
with a piece of linoleum pad, from the supplementary shaft lubricating oil role.
There are two reasons for this failure: one is due to dust in the work environment
more than a long time, so that the surface of the shaft aging and failure of
lubricants, then if you continue to use the printer, it will be due to shaft and
copper sleeve Friction caused by increased mobility of the car dislocation, until
the collision head and can not be used; the other is due to damage caused by the
device. Printer car parking spaces above the photoelectric sensor, it is to the
printer board to provide an important component of the print car reset signal. If
the component is too large or damaged due to dust, the printer will not find the
car back to the car hit the head, which can not be used.
Once this failure should immediately turn off the printer power, hand to
return to the car back to the parking spaces. Find a small piece of sponge or felt
cloth, soaked in sewing machine oil, the tweezers grip back and forth on the
spindle back and forth. It is best to remove the spindle, wash oil. If the fault is
caused by the second cause, it is generally necessary to replace the device.
6. Print Break:
Printer installation of new ink cartridges, basically only need to clean one or
two times, print the ink line will be able to print, generally in use will not break.
There are two main reasons for the disconnection, first, the user does not set
the paper tray before printing, the paper caused by the process of paper, paper
and nozzle caused by disconnection after friction, the feed tray set Can be.
Second, when the original ink runs out, there is no timely replacement of the new
cartridge, and the printer working environment temperature is high, resulting in
print disconnection. General new cartridge installed after three months to run
out and immediately replaced, if the replacement of the ink cartridge is not often
used, will make the cartridge into the air lead to its air tight performance, easy to
28
make ink on the nozzle, the ink cartridge viscosity Becomes larger, resulting in
ink-jet printer failure. In addition, the use of other brands of cartridges will be
disconnected fault. At this time should replace the original cartridge, cleaning
nozzle.
7. The ink cartridge has failed after using the refill
If the physical and chemical properties of the ink into the original ink
cartridges and residual ink are basically similar, it can be used. Because the
operator manually add ink is done in the air under normal pressure, the amount
of ink can not be very consistent grasp of ink, the ink molecules will contain
more bubbles, do not rush to replace such a cartridge after use, but should be
cleaned 1 ~ 2 times after the nozzle shut down the printer, stop 2 to 6 hours and
then use the ink cartridge when the chemical automatically due to the exhaust,
the air bubbles and air to the top of the cartridge, use will reduce the failure.
Another common problem with replenishing ink is the color error. The
production of color materials due to the production of different batches of a
certain color, which is the production of the most difficult color off. Epson ink jet
printer to add ink, generally appear color deviation, as long as the adjustable
range in the Epson software can be set within the scope of the user's printer
settings in the property can be adjusted.
七、 Machine maintenance
In fact, UV printer nozzle maintenance is very critical, there are several UV
printers with automatic cleaning system, nozzle cleaning and UV printer nozzles
have ink compared to overnight shutdown, the nozzle life is very different.
Equipment in the shutdown before the nozzle must be cleaned, and the nozzle on
the moisture pad on the sea, so to ensure that the status of the UV printer nozzle
with the day before yesterday, the picture quality as one.
And relatively no cleaning system equipment (such as 3.2 m large-scale ink jet
machine), shut down when the nozzle surface must be coated with cleaning fluid,
and wrap with plastic wrap, cling film and nozzle tightly, thus reducing the
cleaning fluid, ink evaporation. To a certain extent, extended nozzle life.
If you do not use a long time (such as National Day, Spring Festival and other
long holidays), UV printer nozzle must be removed from the device, soaked with
cleaning fluid and wrap the container with plastic wrap to prevent dust
intrusion, cleaning fluid is volatile.
29