Professional Documents
Culture Documents
Especifcaciones NISSAN TERRANO TD27 PDF
Especifcaciones NISSAN TERRANO TD27 PDF
Engine
Engine ID code TD27T
Number of cylinders R4 i
Number of valves 8, OHV
Capacity/ (bore/ stroke) 2663 cm³ (96,0/ 92,0)
Compression ratio 21,9 ± 0,2: 1
Max. output kW (din hp)/ rpm 73 (100)/ 4000
Max. torque NM/ rpm 220/ 2200
Engine code location Left side front on the edge at the cylinder head
Vehicle Identification Number location Under the right front door on the frame side rail
Vehicle identification plate location Left side engine bay on the scuttle panel
Valve clearance, inlet (cold/ hot) 0,25 warm i
Valve clearance, exhaust (cold/ hot) 0,25 warm i
Valve angle/ seat angle 45° - 45° 30'/ 45°
Piston height over block, mm Max. 0.368 = Head gasket 1.2 ± 0.05 mm i
Valve height in cylinder head, mm Intake ÷ 0.79 - ÷ 1.19 Exhaust ÷ 0.80 - ÷ 1.20 i
Compression pressure, bar 29.4 (Min. 24.5) Max. difference 2.9
Oil pressure/ rpm, bar Min. 0.78/ idle speed (Min. 2.94/ 3000)
Turbo boost pressure, bar Max. 0,84 - 0,89
Radiator cap, bar/ thermostat °C 0,78 - 0,98/ 82° C i
Clutch freeplay, mm 1.0 - 3.0/ 210 - 215 at pedal
Timing gear: (Gear wheel drive) i
Drive belt i
Engine management
Diagnostic connector Left side under dashboard at A - door post
Pump/ pump type Bosch VG distributor pump Kiki 16700-OF002
Crank position °/ engine piston, mm 0° ± 1° before TDC/
Pump position, mm 0,38 ± 0,02 i
Adjustment method Dial micrometer/ Notch i
Injector opening pressure, new, bar 103,0 - 122,8
Injector opening pressure, used, bar 98,1 - 103,0
Injection order 1 - 3 - 4 - 2 (Cylinder 1 at timing gear) i
Injection timing mark location Belt pulley
Electrical system
Battery 2 x 12 V/ 65 Ah
Starter motor current (cranking), A Mitsubishi/ 50 - 75 A/ 3000 - 4000 rpm i
Voltage relay, Volt at/ amp. 14,1 - 14,7/
Terminal definitions DIN 72 552
Alternator max, A 87 A/ 5000 rpm
Glow plug voltage/ drop resistor Approx. 0.65 ohm
Wheel alignment
Load Full tank
Toe-in, ° 0° 20' ± 05'
Camber° 0° 30' ± 30' i
Caster° 1° 35' ± 30' i
KPI/SAI° 12° 37'
Toe-out on turns, inner wheel° 34° 27'
Toe-out on turns, outer wheel° 33° 38'
Technical item Data
Wheel alignment
Rear camber° No factory setting
Rear toe-in ° No factory setting i
Tyre size 235/ 75 R 15
Tyre pressure, front/ rear, bar See sticker left B-doorpost
Free play in suspension parts Factory data i
Track-rod end ball joint, mm Axial 0 - 0,2/ radial 0
Tightening torques
Tightening, NM Torque standards
Cylinder head bolts, stage 1, Nm 39 - 44 Nm oiled i
Cylinder head bolts, stage 2, Nm 54 - 59 Nm
Cylinder head bolts, stage 3, Nm + 90° ± 10°
Cylinder head bolts, stage 4, Nm (Max. distortion 0.2 mm)
Cylinder head bolts, stage 5, Nm (No retightening) i
Main bearings, Nm 167 - 177 step-by-step
Connection rod bearings, Nm 78 - 83
Flywheel, Nm 147 - 167
Crankshaft pulley/ vibration damp. Nm 294 - 324/
Camshaft pulley/ bearings, Nm 44 - 49/ (Rocker arm assembly 20 - 25 Nm)
Pump pulley/ idle wheel, Nm 59 - 69/
Nozzle retainer/ Nozzle in cylinder head 29 - 49/ 54 - 64
Glow plug 15 - 20
Wheel nuts/ bolts, Nm 118 - 147
Wheel hub, front/ rear, Nm 78 - 98 + loosen bolts + 0.5 - 1.5/ i
Brakes
Front, min. thickness (new) 24,0 mm (26,0 mm)
Rear, min. thickness (new) 255,5 mm (254,0 mm)
Capacities
Engine oil/ - incl. filter, litre 6,5/ 7,4 (SAE 10W40)
Manual transmission, litre 3,5 (5 gear) (SAE 80W) i
Final drive, litre Front 1.3 (SAE 90) Rear 2.8 (SAE 80W/ 90) i
Power steering, litre 1,0 (Dexron)
Cooling system, litre 10,0
A/C fluid, type/ gram R134a/ 750 ± 50
A/C oil, type/ cm³ Nissan Type R PAG/ 200
Environmental parametres
Idle speed, rpm 750 ± 50
Max rpm (exhaust test) 5050 ± 100 i
Remarks
n Order No.:
n Mechanic
nn