You are on page 1of 24
aq SERVICE MANUAL AM/FM STEREO RECEIVER SANSUI 441 Sansui. SANSUI ELECTRIC CO., LTD. This service manual is designed for service engineers to repair, adjust, maintain and order the replacement parts of the 441 correctly. When ordering the parts, use the stock number and parts name specifically referring to the Parts Locations & Parts List. For general usage and maintenance of the unit, please refer to the Operating Instructions attached with the unit TABLE OF CONTENTS. Section Title Page J. SPECIFICATIONS ....... wee 2 2. BLOCK DIAGRAM AND LEVEL DIAGRAM a4 3. THREADING OF DIAL CORD 4 341. Threading of Dial Cord 4 3:2. Attachment of Dial Pointer ess... sss : 4 4. ALIGNMENTS AND ADJUSTMENTS ........ : 5 41, FMIF Alignment 5 4-2, FM Dial Calibration, MONO Distortion and RF Alignment... 6 43, MPX Alignment 7 4-4, AMIF, Dial Calibration, RF Alignment 8 ‘TROUBLESHOOTING CHART ...... 9 1. Troubleshooting on Power Supply Section 9 2. Troubleshooting on Audio Section 9 5:3. Troubleshooting on Tuner Section 9 6. PARTS LOCATIONS AND PARTS LIST fees 10 6-1. F-1506F Tuner Circuit Board 10, 11, 12 6-2. F-1508 Pre-Main Amp & Power Circuit Board: 13,14 63. Other Parts (Top Side) ... St 15 6-4, Other Parts (Bottom Side) —— 15 65. _ Other Parts (Front Side) 16 7. SCHEMATIC DIAGRAM ee eee eee i7) 8. PACKING LIST ...... a) 18 9. ACCESSORY PARTS LIST 20... ees, 1. SPECIFICATIONS AUDIO SECTION CONTINUOUS RMS POWER OUTPUT «<1 Watts per channel x2 (both channels driven) LOAD IMPEDANCE 8a POWER BAND 40 to 18,000Hz TOTAL HARMONIC DISTORTION less than 1.0% (from AUX) ‘continuous rms power output «12+ 12W (8G 1,000Hs) INTERMODULATION DISTORTION {at rated power output, 70Hz : 7,000Hz=4:1 SMPTE method! OVERALL (from AUX) «less than 0.8% FREQUENCY RESPONSE (at 1 Watt power output) OVERALL (from AUX) ....25 to 30,000Hz *33dB EQUALIZATION (at TAPE REC output) RIAA Curve (30 to 15,000Hz ++1.5dB) DAMPING FACTOR 20 (82) CHANNEL SEPARATION (1,000H2, at rated power output) ipower (i) PHONO better than 4508 AUX better than 45dB HUM AND NOISE (IHF) PHONO Detter than 70d AUX better than 80d3 INPUT SENSITIVITY AND IMPEDANCE (0004, for rated power output) PHONO, 25m’ 50k (Max. input capability: 90mV at 05% distortion) AUX 150mV 50K TAPE PLAY Pin Jacks REC/PLAY DIN Socket, RECORDING OUTPUT TAPE REC Pin Jacks 150mV REC/PLAY DIN Socket .-30mV SWITCHES AND CONTROLS 150mV 50k 150mV 50k BASS 10dB, ~10dB at SoHz TREBLE 10dB, —10d8 at 10,000Hz LOUDNESS ‘ode’ at SoH #808 at 10000H2 TUNER SECTION FM> TUNING RANGE 188 to 108MH2 SENSITIVITY (IHF) 25nV TOTAL HARMONIC DISTORTION MONO as STEREO, 07% SIGNAL TO NOISE RATIO’ -hetter than 6548 SELECTIVITY better than 60d8 CAPTURE RATIO. 2.508 IMAGE REJECTION better than 55dB at 98MHz IE REJECTION better than 75d8 at 98MHz ‘SPURIOUS RESPONSE REJECTION better than 65d8 at 98MHz SPURIOUS RADIATION less than 34d STEREO SEPARATION .... better than 40d0 at TkH2 FREQUENCY RESPONSE... «30 to 15,000H2 ANTENNA INPUT IMPEDANCE 7 3000 balanced, 750, unbalanced

You might also like