LIFTING EQUIPMENT ENGINEERS ASSOCIATION Candidate No
~ EXAMINATION FOR DIPLOMA - 10 SEPTEMBER 1999
Subject: PART 1 GROUP 1
All questions should be attempted
Time allowed: One hour
Place X in the box alongside the answer of your choice
1+ Miich section ofthe Health and Safety at Work Act 1974 deals with the duties of employers?
2
3
6
(yr
2 Tie parleular to be recorded following a thorough examination of iting equipment are given ia
The Examination of Lifting Equipment Regulations 1998
The Lifting Plant and Equipment (Records of Test and Examination ete) Regulations 1998
The Lifting Opecations and Lifting Equipment Regulations 1998
L_] The Provision and Use of Work Equipment Regulations 1998
3. ‘The maximum fixed period between thorough examin
3S for inservice Ting accessories i:
14 months
12 months
>] 6 months
weekly *
4, ‘The maximum fixed period between therough examinations for in-service:
accessories i:
‘equipment other than
}3 months
}6 months
9 months
12 months 7
5. Asan alternative to having in-servi
Only have it examined by a competent person when he needs to use it
Have it thoroughly examined in accordance with a written scheme of examination
Docs not have to have it exemined if he holds the EC Declaration of Conformity
6. The competent person discovering a serious defect affecting the safely during a thorough examination of a
hhand chain block is legally required to:
Send a copy of the report to the HSE
Enter details in the factory register
Take no ation ether than log his report
7 Toindieate compliance withthe Supply of Machinery (Safety) Regulations 1992 a manufietrer ie reqiced to
mark new lifting equipment with:
The date of test
The CE mack
[_] The name of the tester/examiner
[The date the next examination is due
cxamigelg 18. sept
1ifking equipment thoroughly examined at fixed periods, the user may:2
13,
14,
15,
In addition 10 marking 2 new item (as in 7) 0 show compliance with the Supply of Machinery (Safety)
Regulations, a manufacturer must also issue:
[| an F97 test certificate
[| An examination report
Ayan EC Declaration of Conformity
JA Declaration of Conformity with PUWER
In law the SWL of a two-legged sling may be certified with the angle of the legs:
Only at 0° tothe vertical
(Only at 45° to the vertical
Only at 90° included angle
‘Ataay included angle the user requires
A%BSW eyebolt, SWL I ton 8 om, isto be re-marked in SI units. The correct marking is:
Ra
1400
1400kg
1040kg,
108 is approximatel
2m
[_|2.5m
[3m
3.5m -
2000 ke is approximately:
ton
2,700 Tes
ton
5,500 Ibs
‘The American ton equals:
tonne.
1500 kg
1000 Ib
}2000 1b
‘The Newton is the Si untt for:
Mass
Force
Weight
Length
Hooke's law relates to:
Plasticity
Elasticity
Fatigue
Ductility
cxartg-p eT 9st16.
Ts
19,
20.
ai.
2.
23.
‘Stress
Load divided by area of eross section
Load mukiplied by area of cross section
Area of cross section divided by load
None of these
4.5 tonssq inch
6 tons/sq fach
X18 tons/sq inch
20 tonssq inch
‘what is the shear stress in the pin?
2sonvimm
25N/met
S0ON/mm*
|SON/mant
‘The basic formula for mechanical advantage is:
[7Jroadx etton °
[X] Load effort
Effon + load
Distance moved by effor
Stance moved by load
‘The basic formula for velocity ratio is:
Load x effort
Load + effort
Distance moved by effort + distance moved by load
L._} Distance moved by effort x distance moved by load
Efficiency defined asa percentage is:
X| Mechanical advantage + velocity ratio x 100
[_] Velocity ratio = mechaniea! advantage x 100
Velocity ratiox mechanical advantage x 100
Velocity ratio x mechanical edvantage + 100
A sheave pia in double shear.is subjected to a force of SKN. Ifthe
2s em en
S0kg
100% |
H
Ske,
50kg
78kg,
100Kg
g
examlg-pletonet
200% E fy
Jn the pulley system show, ignoring friction, what effort E is required to balance the load?
A bolt in tension suppor a oad of 6 tons and has across section of % sq inch. What is he eres nthe bolt?
has a cross section'area of 100mm’,
Jo the lever system shown, ignoring friction, what effort E is required to balance the load?