BS TECH PTELTD
Your Global Affianz
Calibration —— a
ceRTICATENO. 03651 PAGE: 1 OF 3
SALES ORDER NO. + BSB-17-0125489
cusromeR + PI-TRANGALINDO EKA PEREADA
JL KERAPU BATU AMPAR, BATA ISLAND
INDONESIA
instRUMENT + METAL HARONESS TESTER
MANUFACTURER + TIME:
uooet vo. SHA
SERALNO, crass
TAG NO, =
ance wun
are causRareo atta?
RECOMMENDED DUE DATE: 2llar18
2 @eaee
(65210) %rh
AMBIENT TEMPERATURE
RELATIVE HUMIDITY
{Tech's organisation and practices have been duly accreted and are compliant to the requirements of ISOMIEC 17025
the laboratory accreditation slandard. Our Quelty Management Sysiem ensures its compatibility withthe requirements of
180 9001:2008.
‘The reference measurement standerds used are traceable to Nallonal Meticlogy Centre (NUCSINGAPORE) andlor other
National standards.
MEASUREMENT TRACEABILITY
REFERENCE STANDARDS AGO. SERIAL NO. AL DATE DUE DATE
HARDNESS BLOCK HRC 701 BS 4411 : 2olun-2016 28-Jun-2017
HARNESS BLOCK HRB 84.6 Bs 1413 : 2tMay-2018——2A-May-2017
HARONESS BLOCK HV 60 Bs 1416 : 9.May-2016 9-May.2017
‘CALIBRATED BY : ‘APPROVED BY :
RISHNA NICHOLAS SHANE MISSON
beststandards@ymail.com
First City Komplek Block 2 #82-02, Batam Center, Batam, Indonesia Tel: 0778-463267, emailCERTIFICATENO. ; BMB 3651
PAGE: 2 OF 3
METHOD OF CALIBRATION
“The calibration certificate was produced in accordance to the instrument was calbted forthe pints specified inthe
relevant in-House Tectnical Procedure, BSE 01,28 defined forthe instrument
‘The decid instrument has been calibrated at BS Laboratory under the ambient conditions sald inthe first page,
[As Received Condon:
Inia esting found the instrument tobe in specifiation forthe parameters tested
‘As Retumed Condltion
[At the completion of the service, measured values were in specication forthe parameters tested
RESULTS OF CALIBRATION
+The expanded uncerainly of measurement associated withthe calibration is estimated al 2 confidence
level of epprosimately 96% wih a coverage factor of k= 2
REMARKS
{+The results of the calibration are given on the atached folowing pages.
{+The results and thr associated uncertainties ae applicable atthe time of calibration
|+Highighted values fll out ofthe manufacture’ specifications. Values not highlighted fall within the range alowed,
+ No agfustnent was done unless otherwise stated.
{+The user should determine the suitability ofthe instrument fr its intended use.
‘The reports shall not be reproduced except in fl, unless the management representatve of 8S TECH PTE LTO has given
‘approval in wetng and comply wth the requitements speci in ISOMEC 17025.
§
5
g
g
ie
a
Z
First City Komplek Block 2 #82-02, Batam Center, Batam, Indonesia Tel: 0778-463267, emailCalibration Certificate LAVA
CERTIFICATE NUMBER: BME 3651 PAGE: 30F 3
TEST RESULT FOR HARONESS TESTER
rds@ymail.com
HRC 70.1 HRC 69.7 04
HRB 04.6 HRB 94.5, oa
Hv 60.0 Hv 597 03
‘TEST RESULT FOR BLOCK CALIBRATOR
HLD 786 (¢ 6) HLD 791 5
First City Komplek Block 2 #B2-02, Batam Center, Batam, Indonesia Tel: 0778-463267, email: beststandar