Professional Documents
Culture Documents
Indicates one of the TXPWR ALM, ODU PS ALM, APC ALM, TPC ALM,
ODU ALM Alarm MJ
ODU SELF CHECK ALM occurrence
Highest
Indicates one of the TXPWR ALM, TX INPUT ALM, RX Level ALM, ODU
ODU TOTAL ALM Alarm severity will
CPU/CABLE OPEN ALM, LOREF, ODU ALM occurrence.
be displayed
ATPC Power ATPC control signal fault (90sec) as well as MAX Power continuation
Status -
Mode 90sec
ODU TYPE Indicate connected ODU type is not supported at iPASOLINK system, or
Alarm MJ
MISMATCH ODU type cannot use in provisioned modulation setting.
ODU PS ALM Alarm ALM in a case of Power supply interruption to ODU. MJ
ODUPS SET Status Status indication of the protection switch for ODU power supplies -
STATUS
0
Modem Alarm and Status
Indication Category Descriptions Severity
Unequipped (MODEM-A) Alarm Reserved and installed optional package is removed from optional slot. MJ
Type Mismatch(MODEM-A) Alarm The equipped type of interface is different from configured type. MJ
BUS ERROR TX Alarm Data communication BUS failure condition in TX direction from STM-1 Card. MJ
BUS ERROR RX Alarm Data communication BUS failure condition in RX direction from STM-1 Card. MJ
HIBER ALM Alarm Radio signal degradation (High BER threshold detection). (Threshold :1E-3/1E-4/1E-5) MJ
LOBER ALM Alarm Radio signal degradation (Low BER threshold detection). (Threshold. :1E-6/1E-7/1E-8/1E-9) MN
EARLY WARNING Alarm Radio signal degradation (Early Warning threshold detection). (Threshold :1E-9) MN
MOD Alarm Indicates the operating status of the MOD. When any failure occurs in the modulator section, “Alarm” is issued. MJ
INPHASE. Status In - Phase indicates the received signal DADE status between No.1 and No.2 MODEM interfaces are in Phase -
condition. In this condition, hitless switch over is available.
L2SYNC LOSS Alarm Loss of frame synchronization of GFP frames on MODEM port. MJ
TDM/AMR Range Mismatch Alarm Mismatch condition when the mapping number of E1 channels are different between TX and RX modem ports or MJ
mismatch condition of selected RX AMR modulation range and TX AMR modulation range.
TX SW Reverse Request Status TXSW request signal receiving condition from the opposite station: -
TX SW Lock in Status Status TXSW Lockin state -
MODEM PS OFF Status Indicate power off condition of power switch which is in front of MODEM-A card. -
1
STM-1 Alarm and Status
Indication Category Descriptions Severity
Unequipped (STM1-A) Alarm Reserved and installed optional package is removed from optional slot. MJ
Type Mismatch(STM1-A) Alarm The equipped type of interface is different from configured type. MJ
Communication
Alarm Communication failure of equipment internal control communication. MJ
FAIL(STM1-A)
Module(STM1-A) Alarm Equipment fault MJ
BUS ERROR TX Alarm Data communication BUS failure condition in TX direction from STM-1 Card. MJ
BUS ERROR RX Alarm Data communication BUS failure condition in RX direction from STM-1 Card. MJ
SNCP PPS-FAIL Alarm. SNCP Path Protection Failure MJ
SNCP Protection Status Status SNCP Path Protection Status indication which indicates [FS, SF, SD, MS, NR] condition. -
APS Protection Status Status APS Line Protection Status indication which indicates {FS,SF,SD,MS,NR} condition. -
RS LOF Alarm SDH Frame synchronization lost in RS (Regenerator Section) on STM-1 port. MJ
RS TIM Alarm Trace Identifier Mismatch detected in RS (Regenerator Section) on STM-1 port. MJ
RS DEG Alarm B1 byte error in RS (Regenerator Section) (RS - Degraded) on STM-1 port. MN
MS RDI Alarm Remote Defect Indication reception in MS (Multiplex Section) on STM-1 port. MJ
AU AIS Alarm AIS detection in AU (Administrative Unit) on STM-1 port. MJ
2
STM-1 Alarm and Status
Indication Category Descriptions Severity
HP UNEQ Alarm HOP (Higher Order Path) Unequipped occurrence on STM-1 port. MJ
HP TIM Alarm HOP (Higher Order Path) Trace Identifier mismatch occurrence on STM-1 port. MJ
HP-PLM Alarm Payload Label Mismatch occurrence in HOP (Higher Order Path) on STM-1 port. MJ
HP-RDI Alarm RDI (Remote Defect Indication) reception in HOP (Higher Order Path) on STM-1 port. MJ
LP – RDI Alarm Remote Defect Indicate reception by an LP (Lower Order Path) on STM-1 port. MJ
LP – PLM Alarm Payload Label Mismatch Failure occurrence by an LP (Lower Order Path) on STM-1 port. MJ
ALS Status Indication of automatic laser shutdown condition at STM-1 optical port. -
RS UAS Status Status UAS status indication on STM port (Repeater Section) -
3
16E1 alarm and Status
Unequipped (16E1) Alarm Reserved and installed optional package is removed from optional slot. MJ
Type Mismatch(16E1) Alarm The equipped type of interface is different from configured type. MJ
BUS ERROR TX Alarm Data communication BUS failure condition in TX direction from STM-1 Card. MJ
BUS ERROR RX Alarm Data communication BUS failure condition in RX direction from STM-1 Card. MJ
E1 AIS Status ALARM/Status category can change according to " AIS Received Condition MJ / -
Setting
4
AUX-A Option Card
Item Name (Input-x) Status/ HKA Status Indication {Alarm, Normal} for every - or
Item Name (Cluster-x) Alarm HKA input. Severity selectable
Item Name (Output-x) Status HKC Status {Alarm, Normal} for every HKC output. -
5
GbE-A option card
6
Equipment Common alarm and Status-1
Unequipped (PS) Alarm Installed Power Supply Module is removed from PS slot. MJ
Unequipped (FAN) Alarm Installed FAN Module is removed from FAN slot. MJ
Unequipped (CLK2M) Alarm Installed CLK2M Module is removed from Main Card. MJ
Type Mismatch (CLK2M) Alarm The equipped type of interface is different from configured type. MJ
Quality Level Status Received quality level condition of each timing source. -
7
Equipment common Alarm and Status -2
Indication Category Descriptions Severity
EXT CLK LOS Alarm Loss of Signal condition of External clock input. MN
EXT CLK AIS Alarm AIS (Alarm Indication Signal) condition of External Clock input. MN
EXT CLK LOF Alarm Loss of frame condition of External Clock input. MN
EXT CLK Loop Alarm Indication of EXTERNAL clock input is used as EXTERNAL clock output. MJ
Item Name (Input-x) Status/ - or Severity
Item Name (Cluster-x) Alarm HKA Status Indication {Alarm, Normal} for every HKA input. selectable
Item Name (Output-x) Status HKC Status {Alarm, Normal} for every HKC output. -
SFP_Type Mismatch (ETH) Alarm Mismatch between SFP on LCT and installed SFP. MJ
8
Equipment common Alarm and Status -3
Indication Category Descriptions Severity
RSTP New Root Bridge Detect Status The notice in which new RootBridge was detected at the time of SpanningTree processing -
RSTP Topology Changed Status The notice in which a Topology change was detected at the time of SpanningTree processing -
The notice which received a Bridge protocol Data Units different in classification of RSTP/STP at the
RSTP Protocol Migration Status time of SpanningTree processing -
RSTP Invalid BPDU Received Status Invalid BPDU message at the time of SpanningTree processing -
Loss of a conditional signaling in which the LLF control signal should be received continuously from
LLF Message Timeout Status the opposite radio equipment.
LLF Status LLF force a LINKDOWN status. The Ethernet port under "edge" mode becomes LINKDOWN. -
The highest
Severity will
IDU TOTAL ALM Alarm IDU TOTAL ALM be reported
Total FDB Full Status The number of DynamicEntryDynamic Entry in L2Switch has reached the maximum number.
FDB Full Status FDB Full indication specified per VLAN basis.
9
ABBREVIATIONS-1
ACAP Adjacent Channel Alternate CIR Committed Information Rate DMM Delay Measurement Message
Polarization CKT Circuit DMR Delay Measurement Reply
ACCP Adjacent Channel Co-Polarization CLK Clock DO Data-out
ACK Acknowledgement CMF Channel Mismatch Failure DSCP Differentiated Services Code Point
AGC Automatic Gain Control CMI Coded Mark Inversion DUP Duplexer
AIS Alarm Indication Signal CONV Converter DXC Digital Cross Connect
ALM Alarm CORBA Common Object Request Broker E1 E-carrier level 1
ALS Auto Laser Shutdown Architecture EBS Express Burst Size
AMR Adaptive Modulation Radio CoS Class of Service EIR Excess Information Rate
ANT, Ant. Antenna CPU Central Processing Unit EMC Electro Magnetic Compatibility
APS Automatic Protection Switch CR Critical EML Element Management Layer
ATT Attenuator CRC Cyclic Redundancy Check EMS Element Management System
ATPC Automatic Transmitter Power Control CS Channel Separation EOW C Order Wire
AU Administrative Unit CTRL Control EPS ETH-Protection Switch
AUX Auxiliary CV near end Code Violation EQL Equalizer
Ave Average CW Carrier Wave ERP ETH-Ring Protection Switch
BBE Background Block Error DA Destination Address ES Errored Seconds
BER Bit Error Rate DADE Differential Absolute Delay Equalizer ETH-CC ETH-Continuity Check function
BPF Band Pass Filter DB Database ETH-LB ETH-Loopback function
BS Base Station DC Direct Current ETH-LBM ETH-Loopback Message
BSC Base Station Controller DCN Data Communication Network ETH-LBR ETH-Loopback Reply
BTS Base Transceiver Station DEG Degraded ETH-LB ETH-Loopback function
CAPEX Capital Expenditure DEI Drop Eligible Indicator ETH-LT ETH- Link Trace function
CBS Committed Burst Size DEM Demodulator ETH-LTM ETH-Link Trace Message
CCDP Co-Channel Dual Polarization Des(Dest) Destination ETH-LTR ETH-Link Trace Reply
CCM Continuity Check Message DI Data-in ETH-OAM Ethernet Operations, Administration
CEPT Conference of European Postal & DL Download and Maintenance
Telecommunication Administration DM Delay Measurement
10
ABBREVIATIONS-2
ETH-OAM LB ETH-OAM Loopback ID Identification LMM Loss Measurement Message
ETH-OAM LT ETH-OAM Link Trace LNA Low Noise Amplifier
IDU Indoor Unit
ETH-RDI ETH-Remote Defect Indication function LO Local Oscillator
IE Internet Explorer
ETSI European Telecommunications LOC Loss of Continuity
IEC International Electro technical
Standards Institute LOF Loss of Frame
Commission
EXC Electrical Cross Connect LOM Loss of Multiframe
IEEE Institute of Electrical and Electronics
E-to-E. End-to-End LOP Loss of Pointer
Engineers
Fail Failure LO REF Local Reference Signal Loss
I/F Interface
F/B Front Back Ratio LOS Loss of Signal
IF Intermediate Frequency
FCS Frame Check Sequence LP Lower order Path
IHG iPASOLINK High Grade
FDB Forwarding Database LPM Link Performance Monitor
IN Input
FE Fast Ethernet LT Link Trace
INTFC Interface
FEC Forward Error Correction LTI Loss of incoming Timing Input
I/O Input/Output
FEBBE Far End Background Block Error LTM Link Trace Message
IP Internet Protocol
FEES Far End Errored Seconds MAC Media Access Control
ITU International Telecommunication Union
FESES Far End Severely Errored Seconds MAIN Main
ITU-R Radio Communication Sector of ITU
FEUAS Far End Unavailable Seconds MAINT Maintenance
ITU-T Telecommunication Sector of ITU
FPGA Field Programmable Gate Array MAX Maximum
L2SW Layer2-Switch
F/W Firmware Mdev Mean Deviation
LAN Local Area Network
GbE, GBE Gigabit Ethernet MDCPU MODEM CPU
LB Loopback
3GPP Third Generation Partnership Project MDI Medium Dependent Interface
LBM Loopback Message
GUI Graphical User Interface MDIX Medium Dependent Interface
LCD Loss of Cell Delineation
H Horizontal Crossover
LCT Local Craft Terminal
HDB High Density Bipolar MD4 Message Digest Algorithm 4
LDPC Low Density Parity Check
HK House Keeping MD5 Message Digest Algorithm 5
LED Light Emitting Diode
HP Higher order Path MEG Maintenance Entity Group
Lev. Level
HYB Hybrid MEM Memory
LLF Link Loss Forwarding
H/W Hardware MEP MEG End Point
LM Loss Measurement
11
ABBREVIATIONS-3
MIN Minimum Octs Octets PMC PASOLINK Management Card
MIP Maintenance Intermediate Point ODU Out-Door Unit PMON Performance Monitor
MIX Mixer OFS Out of Frame Second PNMSj PASOLINK Network Management
MJ Major OMT Ortho-Mode Transducer System Java Version
MMC Multi Media Card OPEX Operational expenditure PPI PDH PHY Interface
MME Mobility Management Entity OPP Opposite ppm parts per million
MMG Mismerge OPR Operation PPP Point-to-Point Protocol
MN Minor OPT Optical PPS Path Protection Switch
MOD Modulator OSPF Open Shortest Path First PQ Priority Queuing
MODEM Modulator Demodulator OSS Operation Support System PRM Parameter
MON Monitor OUT Output PROT Protection
MPX Multiplexer OW Oder Wire PS Power Supply
MS Multiplex Section PA Power Amplifier PSC Protection Switching Counts
MSC Mobile Switching Center PBR Pressurizable Type B, flange profile PSD Protection Switching Duration
MSDU MAC Service Data Unit square Rectangular PWR Power
MSP Multiplex Section Protection PCP Priority Code Point QAM Quadrature Amplitude Modulation
MTBF Mean Time Between Failure PDH Plesiochronous Digital Hierarchy QoS Quality of Service
MTPC Manual Transmitter Power Control PDU Protocol Data Unit QPSK Quadrature Phase Shift Keying
MUX Multiplexing Equipment PGM Program RCVR Recover
N/A Not Applicable PHY Physical REF Reference
NBI Northbound Interface PIR Peak Information Rate REM Remote
NE Network Element PJE Pointer Justification Event RDI Remote Defect Indication
NML Network Management Layer PJE-N Pointer Justification Event Negative Stuff RF Radio Frequency
NMS Network Management System PJE-P Pointer Justification Event Positive Stuff RFS Radio Frequency Systems
OAM Operation Administration and PKG Package RL Relay
Maintenance Pkts Packets RMON Remote Network Monitoring
OCR Occur PLM Payload Label Mismatch RNC Radio Network Controller
12
ABBREVIATIONS-4
RPL Ring Protection Link SUB Substitute UNEXP Unexpected
RS Regenerator Section SW Switch Unicast DMR Unicast Delay Measurement Reply
RS-232 Recommended Standard 232 S/W Software UNM Unexpected MEP
RSL Received Signal Level SWG Switch Group UNP Unexpected Period
RST Regenerator Section Termination SYNC Synchronous USB Universal Serial Bus
RSTP Rapid Spanning Tree Protocol TCI Tag Control Information V Vertical
RX Receiver TCN Threshold Crossing Notification V Volt
SC Service Channel TDM Time Division Multiplex VC Virtual Channel
SD Space Diversity TDMoP TDM over Packet VLAN Virtual LAN
SDH Synchronous Digital Hierarchy TEMP Temperature VP Virtual Path
SEG Segment TERM Terminal VPN Virtual Private Network
SEP Severely Errored Period TF Transmit Fail VSWR Voltage Standing Wave Ratio
SES Severely Errored Seconds TIM Trace Identifier Mismatch WDM Wavelength Division Multiplexing
SFP Small Form factor Pluggable TLV Type Length Value Web World Wide Web
SGMI Security Gateway Management TM Through Mode WG Waveguide
Interface TNC Threaded Neil Councilman WR Warning
SMS Synchronous Multiplexing System ToS Type of Service WRR Weighted Round Robin
SMU Source Measure Unit TPID Tag Protocol Identifier WS Wayside
SNCP Sub-network Connection Protection TQC Total Quality Control XCTRL XPIC Control
SNMP Simple Network Management Protocol TTL Time To Live X-DEM XPIC Demodulator
SP Strict Priority TU Tributary Unit XFP 10(X) Gigabit Small Form Factor
SPD Speed TX Transmitter Pluggable
SRC Source MAC Address UAE UAS Event XIF XPIC IF
STAT Status UAS Unavailable Seconds XPD Cross Polarization Discrimination Ratio
STD Standard UL Upload XPIC Cross Polarization Interference
STM Synchronous Transport Module UNEQ Unequipped Canceller
STP Spanning Tree Protocol XREF XPIC Reference
13