Professional Documents
Culture Documents
www.uninetimaging.com
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com
XEROX WORKCENTRE 4150 • TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
First released in September 2008, the Xerox WorkCentre 4150 is a 45 ppm fax engine that runs at 1200 dpi. The Xerox toner
cartridge #006R01275 is rated for 20,000 pages, and has a list price of $124.99 USD. There is a separate toner and drum
cartridge used in these machines. The drum unit part #013R00623 is rated for 55,000 pages and will be covered in separate
instructions. A new machine ships with a starter cartridge which only has a 10,000 page yield.
The toner cartridges are regional. The #006R01275 is made to work in the US, Europe, Australia, and New Zealand. Part
#006R01276 is made to work in Latin America, Asia, India and Africa. Chips for both regions are available. The chips on these
cartridges need to be replaced each cycle.
There are two versions of these cartridges: the old and new style. The difference is basically the location of the fill plug and a
slightly different internal gear train. The instructions have been split to keeps things clearer.
These are extremely easy cartridges to do. They are fast, and really don’t need to be tested as there is nothing to wear out. All the
normal wear parts like the PCR, developer roller, etc. are in the drum unit. These cartridges are just a supply hopper with a waste
chamber.
SUPPLIES REQUIRED
1. 560g dedicated WC 4150 toner
2. Replacement chip
TOOLS REQUIRED
1. Phillips head screwdriver
2. Small common screwdriver
3. Spring hook
4. Vacuum approved for toner
www.uninetimaging.com
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com
XEROX WORKCENTRE 4150 • TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
1. Remove the two screws located on the waste chamber. 2. Remove the screw located under the colored plastic handle.
OLD STYLE
www.uninetimaging.com
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com
XEROX WORKCENTRE 4150 • TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
4. On the opposite side of the cartridge there is a cover held in place by three plastic tabs.
5. Remove the large drive gear. 6. Remove the toner fill plug. Dump the bulk of the remaining
toner out of the cartridge. Vacuum/blow out the toner supply
chamber clean. It is not necessary to get the cartridge
completely clean now, as the developer roller needs to come
out so the doctor blade can be cleaned. You will have easy
access to clean out the hopper then.
www.uninetimaging.com
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com
XEROX WORKCENTRE 4150 • TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
7. Fill the cartridge with 4150 toner. Replace the fill plug. 8. Angle the top tabs in first and snap the cover back in place.
www.uninetimaging.com
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com
XEROX WORKCENTRE 4150 • TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
10. Replace the chip on the cartridge. Note that the OEM chip is an RF type chip built on a flexible label.
The aftermarket is also an RF type but is built on a solid board. Though physically different from the OEM, it works just fine.
NEW STYLE
11. Remove the waste chamber. There are two small gears that will come loose.
Be careful not to lose them. Slide the cover open and vacuum/blow the waste chamber clean.
www.uninetimaging.com
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com
XEROX WORKCENTRE 4150 • TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
12. Remove the toner fill plug. Dump the bulk of the remaining 13. Fill the cartridge with 4150 toner. Replace the fill plug.
toner out of the cartridge. Vacuum/blow out the toner supply
chamber clean.
14. Install the two gears on the hopper. Install the waste chamber and three screws.
www.uninetimaging.com
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com
XEROX WORKCENTRE 4150 • TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
15. Replace the chip on the cartridge. Note that the OEM chip is an RF type chip built on a flexible label.
The aftermarket is also an RF type but is built on a solid board. Though physically different from the OEM, it works just fine!
CARTRIDGE TROUBLESHOOTING
There is really not much that can go wrong with these cartridges.
From our experience, it is a safe bet that most of the problems will come from the drum unit.
DEFECT CHART
PCR 38mm
Developer roller 44mm
Transfer roller 57mm
OPC Drum 94mm
Upper Fuser roller 126mm
Lower Pressure roller 155mm
www.uninetimaging.com
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com