Professional Documents
Culture Documents
Catalogo Stud PDF
Catalogo Stud PDF
HEADED CONCRETE
ANCHOR – FULL WELD BASE
TYPE HCA STUD
TYPE FHD FERRULE SUPPLIED
Head Diameter (H) – 1/2” for all
1/4” Headed Concrete Anchors.
Head Height (A) – 3/16” for all
1/4” Headed Concrete Anchors. See page ( ) for ferrule specs
HEADED CONCRETE
ANCHOR – FULL WELD BASE
TYPE HCA STUD
TYPE FHD FERRULE SUPPLIED
Head Diameter (H) – 3/4” for all
3/8” Headed Concrete Anchors.
Head Height (A) – 9/32” for all
3/8” Headed Concrete Anchors. See page ( ) for ferrule specs
HEADED CONCRETE
ANCHOR – FULL WELD BASE
TYPE HCA STUD
TYPE FHD FERRULE SUPPLIED
Head Diameter (H) – 1” for all
1/2” Headed Concrete Anchors.
Head Height (A) – 5/16” for all
1/2” Headed Concrete Anchors. See page ( ) for ferrule specs
1/2 1-5/8 HCA 12 158 450 27 12,150 64 lbs. 1,728 lbs. 138 lbs.
1/2 2-1/8 HCA 12 218 400 27 10,800 67 lbs. 1,809 lbs. 166 lbs.
1/2 2-5/8 HCA 12 258 350 27 9,450 71 lbs. 1,917 lbs. 198 lbs.
1/2 3-1/8 HCA 12 318 300 27 8,100 68 lbs. 1,836 lbs. 223 lbs.
1/2 4-1/8 HCA 12 418 200 27 5,400 56 lbs. 1,512 lbs. 277 lbs.
1/2 5-5/16 HCA 12 5516 150 27 4,050 52 lbs. 1,404 lbs. 339 lbs.
1/2 6-1/8 HCA 12 618 125 27 3,375 49 lbs. 1,323 lbs. 388 lbs.
1/2 8-1/8 HCA 12 818 100 27 2,700 50 lbs. 1,350 lbs. 495 lbs.
1/2 10-1/8 HCA 12 1018 75 27 2,025 51 lbs. 1,377 lbs. 680 lbs.
1/2 12-1/8 HCA 12 1218 2000 1 2,000 1,434 lbs. 1,434 lbs. 717 lbs.
HEADED CONCRETE
ANCHOR – FULL WELD BASE
TYPE HCA STUD
TYPE FHD FERRULE SUPPLIED
Head Diameter (H) – 1-1/4” for all
5/8” Headed Concrete Anchors.
Head Height (A) – 5/16” for all
5/8” Headed Concrete Anchors. See page ( ) for ferrule specs
D L SWP B U FD FH Ferrule
1,000
Base Minimum Weld Fillet Weld Fillet Piece
Diameter Length Part# Diameter Base Length Diameter Height
Part Number
Weight
1/4-20 7/8 PCP 1420 78 .215 3/8 5/16 3/32 fer04-P 8.3 lbs.
1/4-20 1-1/8 PCP 1420 118 .215 3/8 5/16 3/32 fer04-P 13.8 lbs.
1/4-20 1-1/4 PCP 1420 114 .215 3/8 5/16 3/32 fer04-P 13.8 lbs.
1/4-20 1-3/8 PCP 1420 138 .215 3/8 5/16 3/32 fer04-P 16.5 lbs.
1/4-20 1-1/2 PCP 1420 112 .215 3/8 5/16 3/32 fer04-P 16.5 lbs.
1/4-20 1-5/8 PCP 1420 158 .215 3/8 5/16 3/32 fer04-P 19.3 lbs.
1/4-20 1-3/4 PCP 1420 134 .215 3/8 5/16 3/32 fer04-P 19.3 lbs.
1/4-20 2-1/8 PCP 1420 218 .215 3/8 5/16 3/32 fer04-P 24.8 lbs.
1/4-20 3-3/8 PCP 1420 338 .215 3/8 5/16 3/32 fer04-P 38.5 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Partial Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or
outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after welding. 5/8”
will be approx. 3/16” shorter after welding.
Material: Low carbon steel, ASTM A29, 1010 1020. PCP studs are also available in weld able stainless steel. Type
302 is the most commonly used, however other grades such as 302, 304, 316, 321, 310, and 430 are available when
required.
D L SWP B U FD FH Ferrule
1,000
Base Minimum Weld Fillet Weld Fillet Piece
Diameter Length Part# Diameter Base Length Diameter Height
Part Number
Weight
5/16-18 7/8 PCP 51618 78 .275 3/8 13/32 7/64 fer05-P 17 lbs.
D L SWP B U FD FH Ferrule
1,000
Base Minimum Weld Fillet Weld Fillet Piece
Diameter Length Part# Diameter Base Length Diameter Height
Part Number
Weight
3/8-16 7/8 PCP 3816 78 .330 13/32 7/16 7/64 fer06-P 25 lbs.
3/8-16 1 PCP 3816 1 .330 13/32 7/16 7/64 fer06-P 25 lbs.
3/8-16 1-1/8 PCP 3816 118 .330 13/32 7/16 7/64 fer06-P 31.3 lbs.
3/8-16 1-3/8 PCP 3816 138 .330 13/32 7/16 7/64 fer06-P 37.5 lbs.
3/8-16 1-1/2 PCP 3816 112 .330 13/32 7/16 7/64 fer06-P 37.5 lbs.
3/8-16 1-5/8 PCP 3816 158 .330 13/32 7/16 7/64 fer06-P 43.8 lbs.
3/8-16 1-3/4 PCP 3816 134 .330 13/32 7/16 7/64 fer06-P 43.8 lbs.
3/8-16 2 PCP 3816 2 .330 13/32 7/16 7/64 fer06-P 50 lbs.
3/8-16 2-1/8 PCP 3816 218 .330 13/32 7/16 7/64 fer06-P 56.3 lbs.
3/8-16 2-1/4 PCP 3816 214 .330 13/32 7/16 7/64 fer06-P 56.3 lbs.
3/8-16 2-3/8 PCP 3816 238 .330 13/32 7/16 7/64 fer06-P 62.5 lbs.
3/8-16 2-1/2 PCP 3816 212 .330 13/32 7/16 7/64 fer06-P 62.5 lbs.
3/8-16 2-5/8 PCP 3816 258 .330 13/32 7/16 7/64 fer06-P 68.8 lbs.
3/8-16 2-3/4 PCP 3816 234 .330 13/32 7/16 7/64 fer06-P 68.8 lbs.
3/8-16 2-7/8 PCP 3816 278 .330 13/32 7/16 7/64 fer06-P 75 lbs.
3/8-16 3 PCP 3816 3 .330 13/32 7/16 7/64 fer06-P 75 lbs.
3/8-16 3-1/8 PCP 3816 318 .330 13/32 7/16 7/64 fer06-P 81.3 lbs.
3/8-16 3-1/2 PCP 3816 312 .330 13/32 7/16 7/64 fer06-P 87.5 lbs.
3/8-16 4 PCP 3816 4 .330 13/32 7/16 7/64 fer06-P 100 lbs.
3/8-16 5 PCP 3816 5 .330 13/32 7/16 7/64 fer06-P 125 lbs.
3/8-16 6 PCP 3816 6 .330 13/32 7/16 7/64 fer06-P 150 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Partial Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or
outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after welding. 5/8”
will be approx. 3/16” shorter after welding.
Material: Low carbon steel, ASTM A29, 1010 1020. PCP studs are also available in weld able stainless steel. Type
302 is the most commonly used, however other grades such as 302, 304, 316, 321, 310, and 430 are available when
required.
Low Carbon Mechanical Property Requirements HOW TO ORDER
Specify diameter, thread size before weld (BW) length,
Tensile Strength 61,000 psi min. type of material.
Yield Strength 49,000 psi min. EXAMPLE
Elongation (% in 2 in.) 17% min. 1/2-13 x 1-1/8” (BW) partial thread (PT), mild steel
Elongation (% in 5x dia.) 14% min. When ordering Stainless Steel, SS will be added to the
Reduction of Area 50% min. part number. Example: Partial Thread Stainless Steel
1/4-20x1”= PCPSS 1420 1
D L SWP B U FD FH Ferrule
1,000
Base Minimum Weld Fillet Weld Fillet Piece
Diameter Length Part# Diameter Base Length Diameter Height
Part Number
Weight
1/2-13 1 PCP 1213 1 .448 1/2 19/32 5/32 fer08-P 46 lbs.
1/2-13 1-1/8 PCP 1213 118 .448 1/2 19/32 5/32 fer08-P 57.5 lbs.
1/2-13 1-1/2 PCP 1213 112 .448 1/2 19/32 5/32 fer08-P 69 lbs.
1/2-13 2-1/2 PCP 1213 212 .448 1/2 19/32 5/32 fer08-P 115 lbs.
1/2-13 3 PCP 1213 3 .448 1/2 19/32 5/32 fer08-P 138 lbs.
1/2-13 3-1/2 PCP 1213 312 .448 1/2 19/32 5/32 fer08-P 161 lbs.
1/2-13 4 PCP 1213 4 .448 1/2 19/32 5/32 fer08-P 184 lbs.
1/2-13 4-1/2 PCP 1213 4 .448 1/2 19/32 5/32 fer08-P 207 lbs.
1/2-13 5 PCP 1213 5 .448 1/2 19/32 5/32 fer08-P 230 lbs.
1/2-13 5-1/2 PCP 1213 512 .448 1/2 19/32 5/32 fer08-P 253 lbs.
1/2-13 6 PCP 1213 6 .448 1/2 19/32 5/32 fer08-P 276 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Partial Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or
outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after welding. 5/8”
will be approx. 3/16” shorter after welding.
Material: Low carbon steel, ASTM A29, 1010 1020. PCP studs are also available in weld able stainless steel. Type
302 is the most commonly used, however other grades such as 302, 304, 316, 321, 310, and 430 are available when
required.
Low Carbon Mechanical Property Requirements HOW TO ORDER
Tensile Strength 61,000 psi min. Specify diameter, thread size before weld (BW) length,
type of material.
Yield Strength 49,000 psi min. EXAMPLE
1/2-13 x 1-1/8” (BW) partial thread (PT), mild steel
Elongation (% in 2 in.) 17% min.
When ordering Stainless Steel, SS will be added to the
Elongation (% in 5x dia.) 14% min. part number. Example: Partial Thread Stainless Steel
1/4-20x1”= PCPSS 1420 1
Reduction of Area 50% min.
D L SWP B U FD FH Ferrule
1,000
Base Minimum Weld Fillet Weld Fillet Piece
Diameter Length Part# Diameter Base Length Diameter Height
Part Number
Weight
5/8-11 1-1/4 PCP 5811 114 .562 5/8 3/4 3/16 fer10-P 87.5 lbs.
5/8-11 1-1/2 PCP 5811 112 .562 5/8 3/4 3/16 fer10-P 105 lbs.
5/8-11 2 PCP 5811 2 .562 5/8 3/4 3/16 fer10-P 140 lbs.
5/8-11 2-1/2 PCP 5811 212 .562 5/8 3/4 3/16 fer10-P 175 lbs.
5/8-11 3 PCP 5811 3 .562 5/8 3/4 3/16 fer10-P 210 lbs.
5/8-11 3-1/2 PCP 5811 312 .562 5/8 3/4 3/16 fer10-P 245 lbs.
5/8-11 4 PCP 5811 4 .562 5/8 3/4 3/16 fer10-P 280 lbs.
5/8-11 5 PCP 5811 5 .562 5/8 3/4 3/16 fer10-P 350 lbs.
5/8-11 5-1/2 PCP 5811 512 .562 5/8 3/4 3/16 fer10-P 385 lbs.
5/8-11 6 PCP 5811 6 .562 5/8 3/4 3/16 fer10-P 420 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Partial Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or
outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after welding. 5/8”
will be approx. 3/16” shorter after welding.
Material: Low carbon steel, ASTM A29, 1010 1020. PCP studs are also available in weld able stainless steel. Type
302 is the most commonly used, however other grades such as 302, 304, 316, 321, 310, and 430 are available when
required.
HOW TO ORDER
Low Carbon Mechanical Property Requirements Specify diameter, thread size before weld (BW) length,
type of material.
Tensile Strength 61,000 psi min. EXAMPLE
Yield Strength 49,000 psi min. 1/2-13 x 1-1/8” (BW) partial thread (PT), mild steel
When ordering Stainless Steel, SS will be added to the
Elongation (% in 2 in.) 17% min.
part number. Example: Partial Thread Stainless Steel
Elongation (% in 5x dia.) 14% min. 1/4-20x1”= PCPSS 1420 1
D L SWP B U FD FH Ferrule
1,000
Base Minimum Weld Fillet Weld Fillet Piece
Diameter Length Part# Diameter Base Length Diameter Height
Part Number
Weight
3/4-10 1-1/2 PCP 3410 112 .680 13/16 7/8 1/4 fer12-P 160.5 lbs.
3/4-10 2 PCP 3410 2 .680 13/16 7/8 1/4 fer12-P 214 lbs.
3/4-10 2-1/2 PCP 3410 212 .680 13/16 7/8 1/4 fer12-P 267.5 lbs.
3/4-10 3 PCP 3410 3 .680 13/16 7/8 1/4 fer12-P 321 lbs.
3/4-10 3-1/2 PCP 3410 312 .680 13/16 7/8 1/4 fer12-P 374.5 lbs.
3/4-10 4 PCP 3410 4 .680 13/16 7/8 1/4 fer12-P 428 lbs.
3/4-10 4-1/2 PCP 3410 412 .680 13/16 7/8 1/4 fer12-P 481.5 lbs.
3/4-10 5 PCP 3410 5 .680 13/16 7/8 1/4 fer12-P 535 lbs.
3/4-10 5-1/2 PCP 3410 512 .680 13/16 7/8 1/4 fer12-P 588.5 lbs.
3/4-10 6 PCP 3410 6 .680 13/16 7/8 1/4 fer12-P 642 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Partial Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or
outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after welding. 5/8”
will be approx. 3/16” shorter after welding.
Material: Low carbon steel, ASTM A29, 1010 1020. PCP studs are also available in weld able stainless steel. Type
302 is the most commonly used, however other grades such as 302, 304, 316, 321, 310, and 430 are available when
required.
HOW TO ORDER
Low Carbon Mechanical Property Requirements
Specify diameter, thread size before weld (BW) length,
type of material.
Tensile Strength 61,000 psi min.
EXAMPLE
Yield Strength 49,000 psi min. 1/2-13 x 1-1/8” (BW) partial thread (PT), mild steel
When ordering Stainless Steel, SS will be added to the
Elongation (% in 2 in.) 17% min.
part number. Example: Partial Thread Stainless Steel
Elongation (% in 5x dia.) 14% min. 1/4-20x1”= PCPSS 1420 1
D L SWP B U FD FH Ferrule
1,000
Base Minimum Weld Fillet Weld Fillet Piece
Diameter Length Part# Diameter Base Length Diameter Height
Part Number
Weight
7/8-9 2 PCP 789 2 .798 7/8 1 5/16 fer14-P 325 lbs.
7/8-9 2-1/2 PCP 789 212 .798 7/8 1 5/16 fer14-P 406.3 lbs.
7/8-9 3-1/2 PCP 789 312 .798 7/8 1 5/16 fer14-P 568.8 lbs.
7/8-9 4-1/2 PCP 789 412 .798 7/8 1 5/16 fer14-P 731.3 lbs.
893.75
7/8-9 5-1/2 PCP 789 512 .798 7/8 1 5/16 fer14-P
lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Partial Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or
outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after welding. 5/8”
will be approx. 3/16” shorter after welding.
Material: Low carbon steel, ASTM A29, 1010 1020. PCP studs are also available in weld able stainless steel. Type
302 is the most commonly used, however other grades such as 302, 304, 316, 321, 310, and 430 are available when
required.
Elongation (% in 2 in.) 17% min. When ordering Stainless Steel, SS will be added to the
part number. Example: Partial Thread Stainless Steel
Elongation (% in 5x dia.) 14% min. 1/4-20x1”= PCPSS 1420 1
Reduction of Area 50% min.
D L SWP FD FH Ferrule
1,000
Weld Fillet Weld Fillet Piece
Diameter Length Part# Diameter Height
Part Number
Weight
*Also available in metric. See ferrule spec sheet for ferrule specs.
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the
inside or outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be
made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. PCF studs are also available in weldable stainless
steel. Type 302 is the most commonly used. Other grades of stainless steel (except Type 303) are
available when required.
Elongation (% in 2 in.) 17% min. When ordering Stainless Steel, SS will be added to the
part number. Example: Partial Thread Stainless Steel
Elongation (% in 5x dia.) 14% min. 1/4-20x1”= PCPSS 1420 1
Reduction of Area 50% min.
1/4-20 1-1/8 PCF 1420 118 23/64 7/64 fer04-FHD 13.8 lbs.
1/4-20 1-1/4 PCF 1420 114 23/64 7/64 fer04-FHD 13.8 lbs.
1/4-20 1-3/8 PCF 1420 138 23/64 7/64 fer04-FHD 16.5 lbs.
1/4-20 1-1/2 PCF 1420 112 23/64 7/64 fer04-FHD 16.5 lbs.
1/4-20 1-5/8 PCF 1420 158 23/64 7/64 fer04-FHD 19.3 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or
outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after welding. 5/8”
will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be made in any length above the
standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. PCF studs are also available in weldable stainless steel. Type
302 is the most commonly used. Other grades of stainless steel (except Type 303) are available when required.
HOW TO ORDER
Low Carbon Mechanical Property Requirements
Specify diameter, thread size before weld (BW) length,
type of material.
Tensile Strength 61,000 psi min.
EXAMPLE
Yield Strength 49,000 psi min. 1/2-13 x 1-1/8” (BW) partial thread (PT), mild steel
When ordering Stainless Steel, SS will be added to the
Elongation (% in 2 in.) 17% min.
part number. Example: Partial Thread Stainless Steel
Elongation (% in 5x dia.) 14% min. 1/4-20x1”= PCPSS 1420 1
5/16-18 1-1/8 PCF 51618 118 7/16 7/64 fer05-FHD 21.3 lbs.
5/16-18 1-1/4 PCF 51618 114 7/16 7/64 fer05-FHD 21.3 lbs.
5/16-18 1-3/8 PCF 51618 138 7/16 7/64 fer05-FHD 25.5 lbs.
5/16-18 1-1/2 PCF 51618 112 7/16 7/64 fer05-FHD 25.5 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the
inside or outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be
made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. PCF studs are also available in weldable stainless
steel. Type 302 is the most commonly used. Other grades of stainless steel (except Type 303) are
available when required.
3/8-16 1-1/8 PCF 3816 118 1/2 1/8 fer06-FHD 31.3 lbs.
3/8-16 1-1/4 PCF 3816 114 1/2 1/8 fer06-FHD 31.3 lbs.
3/8-16 1-3/8 PCF 3816 138 1/2 1/8 fer06-FHD 37.5 lbs.
3/8-16 1-1/2 PCF 3816 112 1/2 1/8 fer06-FHD 37.5 lbs.
3/8-16 1-3/4 PCF 3816 134 1/2 1/8 fer06-FHD 43.8 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the
inside or outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be
made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. PCF studs are also available in weldable stainless
steel. Type 302 is the most commonly used. Other grades of stainless steel (except Type 303) are
available when required.
1/2-13 1-1/8 PCF 1213 118 11/16 5/32 fer08-FHD 57.5 lbs.
1/2-13 1-1/4 PCF 1213 114 11/16 5/32 fer08-FHD 57.5 lbs.
1/2-13 1-5/8 PCF 1213 158 11/16 5/32 fer08-FHD 80.5 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the
inside or outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be
made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. PCF studs are also available in weldable stainless
steel. Type 302 is the most commonly used. Other grades of stainless steel (except Type 303) are
available when required.
HOW TO ORDER
Low Carbon Mechanical Property Requirements
Specify diameter, thread size before weld (BW) length,
type of material.
Tensile Strength 61,000 psi min.
EXAMPLE
Yield Strength 49,000 psi min. 1/2-13 x 1-1/8” (BW) partial thread (PT), mild steel
When ordering Stainless Steel, SS will be added to the
Elongation (% in 2 in.) 17% min.
part number. Example: Partial Thread Stainless Steel
Elongation (% in 5x dia.) 14% min. 1/4-20x1”= PCPSS 1420 1
5/8 1-1/4 PCF 5811 114 7/8 3/16 fer10-FHD 87.5 lbs.
5/8 1-1/2 PCF 5811 112 7/8 3/16 fer10-FHD 105 lbs.
5/8 2-1/4 PCF 5811 214 7/8 3/16 fer10-FHD 157.5 lbs.
5/8 2-1/2 PCF 5811 212 7/8 3/16 fer10-FHD 175 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the
inside or outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be
made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. PCF studs are also available in weldable stainless
steel. Type 302 is the most commonly used. Other grades of stainless steel (except Type 303) are
available when required.
3/4 1-1/4 PCF 3410 114 1-1/16 1/4 fer12-F 133.8 lbs.
3/4 1-1/2 PCF 3410 112 1-1/16 1/4 fer12-F 160.5 lbs.
3/4 1-3/4 PCF 3410 134 1-1/16 1/4 fer12-F 187.3 lbs.
3/4 2-1/4 PCF 3410 214 1-1/16 1/4 fer12-F 240.8 lbs.
3/4 2-1/2 PCF 3410 212 1-1/16 1/4 fer12-F 267.5 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the
inside or outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be
made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. PCF studs are also available in weldable stainless
steel. Type 302 is the most commonly used. Other grades of stainless steel (except Type 303) are
available when required.
Elongation (% in 2 in.) 17% min. When ordering Stainless Steel, SS will be added to the
part number. Example: Partial Thread Stainless Steel
Elongation (% in 5x dia.) 14% min. 1/4-20x1”= PCPSS 1420 1
Reduction of Area 50% min.
7/8 2-1/2 PCF 789 212 1-1/8 5/16 fer14-F 406.3 lbs.
7/8 3-1/2 PCF 789 312 1-1/8 5/16 fer14-F 568.8 lbs.
7/8 4-1/2 PCF 789 412 1-1/8 5/16 fer14-F 731.3 lbs.
*Also available in metric. See ferrule spec sheet for ferrule specs.
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the
inside or outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be
made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. PCF studs are also available in weldable stainless
steel. Type 302 is the most commonly used. Other grades of stainless steel (except Type 303) are
available when required.
Elongation (% in 2 in.) 17% min. When ordering Stainless Steel, SS will be added to the
part number. Example: Partial Thread Stainless Steel
Elongation (% in 5x dia.) 14% min. 1/4-20x1”= PCPSS 1420 1
D L SWP FD FH Ferrule
1,000
Weld Fillet Weld Fillet Piece
Diameter Length Part# Diameter Height
Part Number
Weight
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the
inside or outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be
made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. PCF studs are also available in weldable stainless
steel. Type 302 is the most commonly used. Other grades of stainless steel (except Type 303) are
available when required.
Elongation (% in 2 in.) 17% min. When ordering Stainless Steel, SS will be added to the
part number. Example: Partial Thread Stainless Steel
Elongation (% in 5x dia.) 14% min. 1/4-20x1”= PCPSS 1420 1
D L SWP B U FD FH Ferrule
Base Minimum Weld Fillet Weld Fillet
Diameter Length Part# Diameter Base Length Diameter Height
Part Number
RB Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or
outside of an angle.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products RB Studs can be made
in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. RB studs are also available in weldable stainless
steel. Type 302 is the most commonly used. Other grades of stainless steel (except Type 303) are
available when required.
D L SWP B U FD FH Ferrule
Base Minimum Weld Fillet Weld Fillet
Diameter Length Part# Diameter Base Length Diameter Height
Part Number
FB 51618
5/16-18 25/32 5/16 .250 7/16 7/64 fer05-FHD
2532
FB 71614
7/16-14 25/32 7/16 .281 19/32 9/64 fer07-FHD
2532
FB 3410
3/4-10 1-15/64 3/4 .500 1-1/16 1/4 fer12-F
11564
Full Base Studs are used where additional shear strength is required at the weld.
Length: Length is listed before weld. Studs diameters 1/2” and below will be approx. 1/8” shorter after
welding. 5/8” will be approx. 3/16” shorter after welding. Stud Welding Products PCF Studs can be
made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29 1010-1020. Stainless steel 18-8.
D T SWP B T Ferrule
Thread Thread Base Stud
Diameter Length
Part# Diameter Length
Part Number
HOW TO ORDER
Specify diameter, thread size before weld (BW) length, type of material.
EXAMPLE
1/2-13 x 1-1/8” (BW) partial thread (PT), mild steel
When ordering Stainless Steel, SS will be added to the part number.
Example: Partial Thread Stainless Steel 1/4-20x1”= PCPSS 1420 1
Diameters 9/16” and below will be 1/8” shorter AFTER weld
Diameters “ 5/8 - 7/8” will be 3/16” shorter AFTER weld
Diameters 1- 1 1/4” will be 1/4” shorter AFTER weld
Shoulder Studs are used where additional shear strength is required at the weld.
Material: Low carbon steel, ASTM A 108 1010-1020. Stainless steel 18-8.
*Also available in metric. Other sizes available. See ferrule spec sheet for ferrule specs.
HOW TO ORDER
Specify diameter, thread size before weld (BW) length, type of material.
EXAMPLE
CK .330 x 4 1/8 w/ 3/8-16 x 5/8
When ordering Stainless Steel, SS will be added to the part number.
Collar Studs are used to provide a spacer between the parent metal andthe part secured on threaded
extension.
Material: Low carbon steel, ASTM A 108 1010-1020. Stainless steel 18-8.
B E
H
C
SWP Min.
D B Part# C E H X
BL
3/8-16 1.375 BC 3816 138 .625 .331 5/8 .109 5/8
*Also available in metric. See ferrule spec sheet for ferrule specs.
HOW TO ORDER
Specify diameter, thread size before weld (BW) length,
type of material.
EXAMPLE
C x BLW D x B
When ordering Stainless Steel, SS will be added to the
part number.
Threads: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request.
Other diameters available upon request.
Material: Low carbon steel, C - 0.23% max., P - 0.04% max., Mn - 0.60% max., S - 0.05% max.
B D L T SWP Ferrule
Stud
Diameter
Tap Diameter Length (BW) Tap Depth Part# Part Number
HOW TO ORDER
Specify base diameter, finished length before weld (BW) length, tap
size, tap depth and type of material.
EXAMPLE
5/8 x 1-1/4” (BW) Tapped Stud (TS) with a 3/8-16 x 7/16 tap,
mild steel
When ordering Stainless Steel, SS will be added to the part number.
Diameters 9/16” and below will be 1/8” shorter AFTER weld
Diameters “ 5/8 - 7/8” will be 3/16” shorter AFTER weld
Diameters 1- 1 1/4” will be 1/4” shorter AFTER weld
Tapped Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or outside
of an angle.
Length: Length is listed before weld. Studs Welding Products TP Studs can be made in any length above the
standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. TP studs are also available in weldable stainless steel.
HOW TO ORDER
Specify base diameter, finished length before weld (BW) length, tap
size, tap depth and type of material.
EXAMPLE
5/8 x 1-1/4” (BW) Tapped Stud (TS) with a 3/8-16 x 7/16 tap,
mild steel
When ordering Stainless Steel, SS will be added to the part number.
Diameters 9/16” and below will be 1/8” shorter AFTER weld
Diameters “ 5/8 - 7/8” will be 3/16” shorter AFTER weld
Diameters 1- 1 1/4” will be 1/4” shorter AFTER weld
Tapped Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or outside
of an angle.
Length: Length is listed before weld. Studs Welding Products TP Studs can be made in any length above the
standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. TP studs are also available in weldable stainless steel.
D L SWP FD FH Ferrule
Weld Fillet Weld Fillet
Stud Diameter Length (BW) Part# Diameter Height
Part Number
*Also available in metric. See ferrule spec sheet for ferrule specs.
NT Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or
outside of an angle.
Length: Length is listed before weld. Stud Welding Products NT Studs can be made in any length above
the standard minimum.
Material: Low carbon steel, ASTM A29, 1010 1020. NT studs are also available in weldable stainless
steel.
HOW TO ORDER
Low Carbon Mechanical Property Requirements
Specify diameter, thread size before weld (BW) length,
type of material.
Tensile Strength 55,000 psi min.
EXAMPLE
Yield Strength 50,000 psi min. 1/2 x 1 No Thread Pin
When ordering Stainless Steel, SS will be added to the
Elongation (% in 2 in.) 17% min.
part number.
Elongation (% in 5x dia.) 14% min. Diameters 9/16” and below will be 1/8” shorter AFTER weld
Diameters “ 5/8 - 7/8” will be 3/16” shorter AFTER weld
Reduction of Area 50% min. Diameters 1- 1 1/4” will be 1/4” shorter AFTER weld
Boiler Tube Heat Transfer Pins are designed for power, or waste boiler/incinerator lining and re-lining.
Specify auto feed quality required.
Material: Low carbon steel, ASTM 108. Stainless steel 430, 302, 304, 310, 316 and 320.
D B L
SWP Ferrule
Part# Part Number
Rope hook studs are designed to be welded to trucks, trailers and other vehicles to provide a means
of securing tarpaulins with ropes. Studs can be rapidly applied, compared to manual welding of J-bent
rods, the Rope Hook studs are ideal in situations where large quantities of studs must be applied.
Rope Hook studs can be welded to the perimeter of multistory buildings to facilitate the securing of
ropes during building construction. Rope Hook studs meet OSHA regulations for such applications.
Material: Available in low carbon mild steel and stainless steel 302 and 306.
*Also available in metric. See ferrule spec sheet for ferrule specs.
A
D
Stud Max
Diameter Length Min Min Opening SWP Ferrule
D L R A O Part# Part Number
Eyebold studs are welded to a variety of parts or structures to provide a means of attachment to the
assembly or a means of lifting parts.
The length of the weld base portion of the stud is needed for the ferrule height and the burn off, or length
reduction, during the stud welding process.
Material: Available in low carbon mild steel and stainless steel 302 and 304.
D SWP HD HT FD FH Ferrule
Diameter
L Part# Head Head Fillet Fillet
Part Number
Diameter Height Diameter Height
1) Stud Welding Products studs are available in any length above the standard minimum.
2) Listed Ferrule above is for the standard flat down hand position.