Professional Documents
Culture Documents
Install Guide For CR QS3.5.463SP2 PDF
Install Guide For CR QS3.5.463SP2 PDF
5
Healthcare – IT R&D Install Guide
8/10/2008
FOR:
Agfa-Gevaert NV CR QS Verification team & Service documentation writer
General
This Install Guide is intended to be used during installation of a CR QS 3.5 system.
First Check the Prerequisites before starting any install work (Section 1)
According to your situation, select one of the scenario’s in the QS Installation section.
(Section 2).
This is a document you can use to work on. Print it for every system you install.
…⌧ Use the squares to mark and check your steps.
Use the Installation Information forms (Section 4) to write down your values.
1
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Table of Content
Install Guide for CR QS 3.5 ___________________________________________________________ 1
1 Prerequisites ______________________________________________________________________ 4
1.1. Check hardware to see if it is supported for CR QS OS XP _______________________________ 4
1.2. Use the correct set of the OS CD’s ____________________________________________________ 4
1.3. Windows License Key ______________________________________________________________ 4
1.4. Network connected ________________________________________________________________ 4
1.5. Change the keyboard to a QWERTY (US international) keyboard. ________________________ 5
1.6. Adapt Boot Sequence before inserting the OS Installation CD_____________________________ 5
1.6.1 On a Dell WS650/WS670: ________________________________________________________________ 5
1.6.2 On a Dell PE700:________________________________________________________________________ 5
1.6.3 On a Dell Optiplex GX260/GX270: _________________________________________________________ 5
1.6.4 On a Dell Optiplex GX620 ________________________________________________________________ 6
2 QS Installation ____________________________________________________________________ 7
2.1. CR QS 3.5 New Installation _________________________________________________________ 7
2.1.1 New CR QS 3.5 on server _________________________________________________________________ 7
2.1.2 New CR QS 3.5 on Client _________________________________________________________________ 7
2.2. Upgrade from a previous CR QS 3.5 __________________________________________________ 8
2.2.1 CR QS 3.5 Upgrade on server ______________________________________________________________ 8
2.2.2 CR QS 3.5 Upgrade on client ______________________________________________________________ 8
2.3. Upgrade CR QS 3.0 MR2 to CR QS 3.5 _______________________________________________ 9
2.3.1 CR QS 3.0 MR2 to CR QS 3.5 on Server _____________________________________________________ 9
2.3.2 CR QS 3.0 MR2 to CR QS 3.5 on Client _____________________________________________________ 9
2.4. Upgrade CR QS 3.0.210 to CR QS 3.5________________________________________________ 11
2.4.1 CR QS 3.0.210 to CR QS 3.5 on Server _____________________________________________________ 11
2.4.2 CR QS 3.0.210 to CR QS 3.5 on Client _____________________________________________________ 12
2.5. Upgrade ADC-QS 2.1.xxx to CR QS 3.5 ______________________________________________ 13
2.5.1 ADC-QS 2.1.xxx to CR QS 3.5 on Server____________________________________________________ 13
2.5.2 ADC-QS 2.1.xxx to CR QS 3.5 on Client ____________________________________________________ 14
3 Operating system Install ___________________________________________________________ 15
3.1. Booting the OS CD _______________________________________________________________ 15
3.1.1 On a Dell WS650 and Dell OptiPlex GX260/GX270: __________________________________________ 15
3.1.2 On a Dell WS670: ______________________________________________________________________ 15
3.1.3 On a Dell PE700:_______________________________________________________________________ 17
3.1.4 On a Dell GX620: ______________________________________________________________________ 17
3.2. Installation Type _________________________________________________________________ 18
3.2.1 Server Installation ______________________________________________________________________ 18
3.2.2 Client Installation ______________________________________________________________________ 20
3.3. Unattended install (similar for Server an Client) _______________________________________ 21
3.3.1 On a Dell PE700:_______________________________________________________________________ 21
3.3.2 On a Dell WS650/WS670 and Dell Optiplex GX260/GX270/GX620 ______________________________ 21
3.4. Operating system Settings _________________________________________________________ 22
3.4.1 Log on as Administrator _________________________________________________________________ 22
3.4.2 Provide the correct Product ID ____________________________________________________________ 22
3.4.3 Install additional languages (Optional) ______________________________________________________ 24
3.4.4 Install Hot Fixes and Updates(Recommended) ________________________________________________ 27
2
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
3.4.5 Change TCP/IP Settings _________________________________________________________________ 28
3.4.6 Change Computer/Host Name and Workgroup________________________________________________ 29
3.4.7 Date & Time __________________________________________________________________________ 31
3.4.8 Unicode / Language Settings______________________________________________________________ 32
3.4.9 Create Users __________________________________________________________________________ 35
3.5. Back to QS Install ________________________________________________________________ 36
4 Installation Information Forms _____________________________________________________ 37
4.1. Server Installation Information form ________________________________________________ 37
4.2. Client Installation Information form_________________________________________________ 38
3
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
1 Prerequisites
1.1. Check hardware to see if it is supported for CR QS OS XP
Install the CR QS Windows XP Server OS only on machines that are on the supported
HW list.
CR QS OS Languages CD’s
If you need to install additional languages (languages other than English)
“Western Europe” - “Asian” – “Nordic & Portuguese” – “Eastern Europe & Middle East”
4
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
1.5. Change the keyboard to a QWERTY (US international) keyboard.
When you log on as administrator you will always have the English version of Windows
XP. Therefore it is easier working with a QWERTY keyboard (US international) attached
when you have to type something.
5
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
<Esc>
<Esc>
<Enter>Save and exit Setup.
REBOOT
6
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
2 QS Installation
2.1. CR QS 3.5 New Installation
2.1.1 New CR QS 3.5 on server
Before starting, fill in the Server Installation Information Form (Section 4.1)
Install the CR QS Server Operating System. Jump to Section 3 (Operating System
Install)
Back from OS Installation
Insert the Application CD
Run K:\CR QS 3.5.msi
Click <Next>, <Accept License>, <Next>, <Next>, check Server radiobutton , <Next>,
<Install>
When Secset II pops up, check the values, and if needed, change them. Press OK
button.
Click <Finish>
Click <Yes> to reboot
Before starting, fill in the Client Installation Information Form (Section 4.2) for every
Client system.
Install the CR QS Client Operating System. Jump to Section 3 (Operating System
Install)
Back from OS Installation
Insert the Application CD
Run K:\CR QS 3.5.msi
Click <Next>, <Accept License>, <Next>, <Next>, check Client radiobutton, <Next>,
Fill in the hostname of the QS Server, <Next>, <Install>
When Secset II pops up, check the values, and if needed, change them. Press OK
button.
Click <Finish>
Click <Yes> to reboot
7
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
8
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
When Secset II pops up, check the values, and if needed, change them. Press OK
button.
Click <Finish>
Do not reboot yet when the installer asks you to.
First run D:\Agfa\ADC-QS\Config\RestoreFrom3.5.js.
The script will end with a “done” message.
Click <Yes> to reboot.
9
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Reboot
Open Windows Explorer and remove the following maps on D:
\Agfa
Insert the CR QS 3.5 application CD
Run K:\CR QS 3.5.msi
Click <Next>, <Accept License>, <Next>
Check the Client radio button, <Next>
Fill in the hostname of the QS Server, <Next>, <Install>
When Secset II pops up, check the values, and if needed, change them. Press OK
button.
Click <Finish>
Do not reboot yet when the installer asks you to.
First run D:\Agfa\ADC-QS\Config\ RestoreFrom3.0.MR2.js.
The script will end with a “done” message.
Click <Yes> to reboot.
10
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
11
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Open “ConfigView – File – Import XML – Full Configuration.
Open “Selector – File – Import study to import saved studies again.
12
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
13
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
14
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
When the system reboots and when the Dell logo screen appears, press the <F12> key
to enter the Boot Menu. If you miss the Dell logo screen, reboot again.
You’ll get following Menu:
6. System Setup
7. IDE Drive Diagnostics
8. Boot to Utility Partition
Enter a choice:_
When the system reboots and when the Dell logo screen appears, press the <F12> key
to enter the Boot Menu. If you miss the Dell logo screen, reboot again.
You’ll get following Menu:
15
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Boot Device Menu
==============
* System Setup
* Hard Drive Diagnostics
* Boot to Utility Partition
Remark:
On a WS 670, when the drivers for the Matrox card are installed, following screen can
appear :
Do NOT click any of the buttons. This screen will disappear on next reboot.
16
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
The boot sequence is set to CD, so the system will boot from the CR QS OS CD.
When the system reboots and when the Dell logo screen appears, press the <F12> key
to enter the Boot Menu. If you miss the Dell logo screen, reboot again.
You’ll get following Menu:
* System Setup
* Hard Drive Diagnostics
* Boot to Utility Partition
17
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
+-------------------------------------------------------------+
! AGFA CR QS Server XP !
! Multi Language !
! SERVER XP !
+-------------------------------------------------------------+
! !
! Detected an upgradable NT4 system. !
! !
! Perform an NT Server upgrade Installation ? !
! !
! (Y) Upgrade from NT4 !
! (N) Other Choice !
+-------------------------------------------------------------+
18
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
+-------------------------------------------------------------+
! AGFA CR QS Server XP !
! Multi Language !
! SERVER XP !
+-------------------------------------------------------------+
! !
! Detected an upgradable 2003/XP system. !
! !
! Perform a 2003/XP Server upgrade Installation ? !
! !
! (Y) Upgrade from 2003/XP Server !
! (N) Other Choice !
+-------------------------------------------------------------+
If you had the proposal for an upgrade (NT4 or 2003/XP) and you select “N” the script
will jump to the NEW Installation proposal
+-------------------------------------------------------------+
! AGFA CR QS Server XP !
! Multi Language !
! SERVER XP !
+-------------------------------------------------------------+
! !
! New SERVER Installation. !
! !
! (Y) This machine will be reinstalled totally !
! (N) Exit to Operating system !
+-------------------------------------------------------------+
If you answer “N” on the NEW Installation screen, the installation exits to DOS.
To Continue, Press Y
19
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
The installation procedure will check which scenario is the most logical.
This OS CD is developed to be used for other products too.
If you see following screen, Press (N)
+-------------------------------------------------------------+
! AGFA CR QS XP Client !
! Multi Language !
+-------------------------------------------------------------+
! !
! Detected an upgradable NT4 system. !
! !
! Perform an NT upgrade Installation ? !
! !
! (Y) Upgrade from NT4 !
! (N) Other Choice !
+-------------------------------------------------------------+
+-------------------------------------------------------------+
! AGFA CR QS XP Client !
! Multi Language !
+-------------------------------------------------------------+
! !
! Detected an upgradable XP system. !
! !
! Perform an XP upgrade Installation ? !
! !
! (Y) Upgrade from XP !
! (N) Other Choice !
+-------------------------------------------------------------+
If you had the proposal for an upgrade (NT4 or 2003/XP) and you select “N” the script
will jump to the NEW Installation proposal.
20
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
+-------------------------------------------------------------+
! AGFA CR QS Client XP !
! Multi Language !
+-------------------------------------------------------------+
! !
! New CLIENT Installation. !
! !
! (Y) This machine will be totally reinstalled !
! (N) Exit to Operating system !
+-------------------------------------------------------------+
If you answer “N” on the NEW Installation screen, the installation exits to DOS.
To Continue, Press Y
During the installation you’ll see a lot of screens of the Windows XP Setup. Don’t worry,
the installation runs in the background. Don’t click anything on these screens until you
get the log on screen described in 3.4. It could interrupt the installation.
21
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
3.4. Operating system Settings
3.4.1 Log on as Administrator
Approximately 45 minutes later: the log on screen stays on after the reboot.
Change the default license owner data and provide the correct Product ID (Windows
License Key)
22
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
After providing the correct Product ID you will get the following message:
23
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
To install additional languages you have to insert the appropriate CR QS Language CD and
launch MUISETUP.EXE from the CD. This will start the additional language installation:
Remark:
If you need another language click cancel and insert the other CD as requested.
English is the default language; you don’t have to install it.
24
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Select the option “Match the language for non-Unicode programs with the default user
language.
Remarks:
Keep the language for default user to English until the entire system is installed (including QS
software). Install scripts depend on English as default language. The Administrator can define
another language during the setup of the account. Changing the default language for new users
will set the logon screen in this language.
Click OK to start the installation. The installation of the languages takes up to 5 minutes
per selected language.
At the end of the installation you get a confirmation that the installation is completed.
Click OK to finish the installation of the languages that are on this CD.
Click Cancel
25
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Click Yes.
Click OK to finish the installation of the languages that are on this CD.
Repeat Step 3.4.3 if you want to install languages from other Language CD’s.
26
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
To install Hot Fixes an Updates you have to insert the CR QS OS XP Hotfix CD.
Start cd:\hfinst.bat
The installation will take a few minutes (depending on the number of Hotfixes that are
released by Microsoft). Your presence is not required at this moment.
Remark:
If you get the message: “Sorry but we are unable to detect your system type…”
“Would you like a Server, client or NO update?”
You need to select manually what type of update you want:
Type “S” if you want a Server update (for Windows 2003)
Type “C” if you want a Client update (for Windows XP)
Type “N” if you want no updates at all
Click OK to finish the installation. The PC will shut down and restart automatically.
Remark:
If the PC doesn’t shut down automatically, restart the PC manually. Click Start Click Turn off
Computer Click Restart
27
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
28
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
3.4.6 Change Computer/Host Name and Workgroup
Here you can enter the new Computer/Host Name and the Workgroup. After entering
the correct names click OK. If you changed the Workgroup you will get the following
Welcome message:
Click OK here. Next you will get a message that tells you you have to reboot:
29
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Click OK here and then click OK to close the System Properties. Now you will be asked
if you want to reboot the system. Click Yes.
30
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Click OK.
31
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
3.4.8 Unicode / Language Settings
Click OK
Click Apply
32
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Click Yes
Click Yes
Click Start if you want to apply these regional settings to the Default user and all other
QS-users.
33
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
The program keeps you up to date with a progress bar.
Click Close.
Affected users :
Users that will be created in the future
Users that already have been logged on to the system.
Not Affected users :
SYSTEM, LocalService, NetworkService, Administrator and CRService
REMARK: If you are logged on as CRService account to do this, be sure to open \Control
Panel\Regional & Language Settings again and reset it to English. Uncheck the Default user
box again.
34
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Click Create.
A new “New User” dialog will appear. You can keep creating user accounts until you
click the Close button.
click on “Groups”
Double-click on the QSUsers group.
Click the Add button.
Enter the User Names you want to add, separated by a semicolon (;).
Click OK
Click OK
NOTE : This has to be done on every system of the QS cluster. User names and passwords
have to be the same on every system.
35
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
36
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Computer Name
WorkGroup Name
IP Addres
Subnet Mask
Default Gateway
Preferred DNS Server
Alternate DNS Server
37
CR QS 3.5
Healthcare – IT R&D Install Guide
8/10/2008
Computer Name
WorkGroup Name
IP Addres
Subnet Mask
Default Gateway
Preferred DNS Server
Alternate DNS Server
QS Server Name
38