EUROPEAN STANDARD EN 10248-1
NORME EUROPEENNE
EUROPAISCHE NORM une 1895
Ics 77,149.70
Descriptors: tron -and ste] products, hot rolled products, sheet pilings, steels, unalloyed steels, chemical compostion, grades
‘quality, cessiicstions, designation, mechanicel properties, weldabilty, suvece condition, tests, inspection, marking
English version
Hot rolled sheet piling of non alloy steels - Part 1:
Technical delivery conditions
Pyiplanchet laninges a chaud en acters non armagewa lz
aitige = Partie Tz Congivions
Tivrasso
Spundbohien aus untegiersen
fechnsques “ee Stunien = Tes) Tr Techmisene Lieferbeatngungen
‘This European Standard was approved by CEN on 1995-05-19. CEN menbers are bound to comply with the CEN/CENELEC Interna
Regulations which stipulate ehe condisions for giving this European Standard the status of @ national standard without
ary alteration.
Usctovdate Tists and biblfagrashical references concerning such nacional standards may be obtained on appTicatian to
the central Secretariat or to any CEN menber: :
‘The European Standards exist in three official versions (English, French, Garman). A version tn any other language
rete Uy ranstotion under she renponsibi lity of 2 CEN merber Ynta sts own language and notified to the Cent
Stcretariat has the same status as the official versions.
NN nenbers are the nationa) standards bodies of Austria, Belgium, Oearark, Fiolana, France, Gamsany, Gresce, Iceland,
Grelana. Italy, Lonenbourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and Unites Kyngson.
CEN
European Committee for Standardization
Conste Européen de Normalisation
Europaisches Kanitee fur Koreung
Central Secretariat: rue de Stassart,36 B-1050 Brussels
= 1998 An rights of reproduction and communication yn any form and By any nears
reserved in all countries to CEN ang s# nenbers.
Ref. No. EN 10289-1:1995 €Page
EN So248-2:2995
Foreword...
Ba conn
Danone
10
Annex A (normative) Location of samples.
Contents
Scope.
Normative references
Definitions
Information to be supplied by the purchaser.
Classification and designatio
Classification
Designation
Technical requirements...
Steel manufacturing process...
Delivery condition
Chemical composi
Mechanical properties.
Technological properes.
Surface finish........
Inspection and testing...
General.
Specific inspection and testing
Inspection units.
Tensile testing .
Verification of the chemical composition,
Internal defects.
Verification of dimensional tolerances...
Inspection documents.
Marking
Options
Lb biotic boom WNaaoom Wink & HHH dd Dw
oe
Annex B (informative) List of national standards which correspond to referenced
Annex C (informative) List of corresponding former national designations
Euronorm:Page 3
EN 10248-1:1995
Foreword
This European Standard was prepared by SC4 "Sheet piling” of Technical Committee
ECISS/TC10 “Structural steels - Qualities” the secretariat of which is held by NNI.
EN 10248 is composed of two parts :
Part 1 : Technical delivery conditions,
Part 2 : Tolerances on shape and dimensions.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 1995, and conflicting national standards shall
be withdrawn at the latest by December 1995.
According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this
European Staridard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom.