DEUTSCHE NORM December 1999 Steel hexagon nuts with large width across flats for high-strength structural bolting les 21,080.20 Supersedes October 1989 edition Sechskantmuttern mit groen Schldsselweiten fdr Verbindungen mit HV-Schrauben in Stahlkonstruktionen Inkesping with current practice in standerds published by the International Organization for Standerdization 180), @ comma has been used throughout as the decimal marker. Foreword This standard has been prepared by Technical Committee Schraubenverbindungen fir den Stahibau of the Nermentusschub Mechenische Verbindungselemente (Fasteners Standards Committee) Amendments This standard differs from the October 1089 edition in that the nut height is now to be 20 mm (instead of 49 mm) for M24 nuts and references have been updated Previous editions DIN 6918: 1962-08, 1971-01, 1979-03, 1989-10, All dimensions are in milimetres. 1 Scope This standard epecities dimensions and technical delivery conditions for steel hexagon nut with large width across flats for use with DIN 6914 high-strength bolting in friction grip and shear bolt connections (of. DIN 18800-1) in structural steelwork. 2 Normative references This standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the titles of the publications are listed below. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it by amendment or revision, For undated references, the latest edition of the publication referred to applies. DIN 13-12 General purpose ISO metric screw threads ~ Coarse and fine pitch threads with diameters from 1 mm to 300 mm - Selected diameters and pitches DIN 19-15 !SOmetric serew threads ~ Fundamental deviation and tolerances for screw treads of mm ameter and larger DIN 267-02 Fasteners - Technical delivery conditions - Product grades and tolerances DIN 267-10 Fasteners - Technical delivery conditions ~ Hot-dip galvanized components, DIN 4000-2 Tabular layouts of article characteristics for bolts, screws and nuts DIN6914 —_High-strength hexagon head bolts with large widths across flats for structural steel bolting DIN 18800-1 Structural steelwork ~ Design and construction DINEN 499 Fasteners ~ Surface discontinuities ~ Nute Continued on pages 2 and 3. Translation by DIN-Sprachendienst. case of dou, the German tnguage cial should be conated athe author tx {© Naps ofthe vanninn nay bo enodanna Wiha ea pea Feet. No. DIN 6015; 1009-12 cer ag nt 1 Bets a a pt efor Gaman Sand oma. erg prs popes Sane or Deutsches Instat Pur Normang BV ‘20085Page? DIN 6915 ; 1999- DIN EN 20898-2 Mechanical properties of fasteners - Part 2: Nuts with specitied proof load values — Coarse thread DIN EN 1$0.4269 Fasteners - Acceptance inspection (ISO/DIS $269 : 1998)") DIN EN ISO 4042 Fasteners — Electroplated coatings (SO 4042 : 1988) DIN EN ISO 4759-1 Tolerances for fasteners ~ Part 1: Bolts, screws, studs and nuts ~ Product grades A, B and C (ISO/DIS 4759-1 : 1997)") DIN EN ISO 10683 Fasteners - Non-slactrically applied zinc flake coatings (/SO/DIS 10683: 1999)) 1S0 8992 :1986 Fasteners - General requirements for bolts, screws, studs and nuts 3 Dimer Nut dimensions shall be as given in figure 1 and table 1, The nuts shall be countersunk at an angle of 120” on both sides to diameter d. Detail X 90 ‘m,,~ minimum wrenching height (equal to 0,8 mq) Table 1: Nut dimensions Thread size (d) wiz [mie [ mao | mez | wes | mer | mao | mse 7 Ws | 2 25 zs |S 3 a | 4 a) 20 25 | 30 Ee EJ es | 7s | 7 7 an Baa | 256 | sa | Gass | 500] s0as | Sear | 6eae ‘sax (nominal a) | 10 1s 76 7 | we 28 3 i aes | 129 | 149 eo | ta7 [27 [ 227 | 277 ma 77 | 984 Tae | i496 | tase] i016 | 20,16 ed a] ae 36 a 6 EJ 0 a zite | 2616 | at 5 o 3 @ Bae AeproumatemassASOer | 23 | 44a | 73a [ior | ts | 224 | 300 | sis ") The maximum of d, shall not exceed the actual width across flats. 5) Currently at draft stage. ‘opyright bythe DIN Deutsches Institut ur Normang FV Tue Aug 19 16:30:04 2008‘opyright by the Bl Tue Aug 160 Pages DIN 6915: 1988-12 4 Technical delivery conditions Material Stel General requirements ‘Aa specie in 1S0 8902. Tolerance on Thread fs specied in DIN 18-19 and DIN 3.15, Property clase 0 Mechanical properties) As specified in DIN EN a0608-2 Imit deviations and Product grade 8 eometca feieranc ‘As specified in DIN EN ISO #7604 Ae processed DIN EN 80 4042 apples wi regara to electropiatng DIN EN ISO 10688 applies wth regard to zinc fake ‘Surface finish eatinas DIN 287 10 applise wih regard t het dip galvanizing IN 207-2 epplice with regard to surface roughness. DIN EN 493 applies with regard to the widening test and permissible surface discontinuities. Acceptance inspection DIN EN SO 3269 apples with regard To accoplance inspection 1) Stee! boltinut assemblies using DIN 6844 bolts and DIN 6945 nuts are designed to comply with the requirement that ifan adequately lubricated assembly [ails due Lo overtightening, slipping ofthe Uitead ‘enue rather than fracture of the bolt 5 Designation Dasignation of an M20 steel hexagon nut with large width across flats, of property class 10: Nut DIN 6915 -M20 ‘The DIN 4000-2-7-1 tabular layout of article characteristics shall apply to nuts covered in this standard. 6 Marking Nuts shall be marked in accordance with DIN EN 20808. . and the symbol HV imprinted on the side face. Deutsches Institat Pur Normang FV 2085