INSTRUCTION MANUAL
FOR
SINGER
MACHINES
THE SINGER COMPANYCONTENTS
1 Application
2.Notes on safety
3.Commissioning
4.Instaling the belt quaré
5 Lubrication
8 Neale and thread
T.inseriing the needle
8.To remove the bobbin case
9.To wind the bobbin
10. Threading the boats
11.To replace tne bobbin case
12. Threaging the needle
13. To adjust st
length
14. To adjust aresser foot pressure
15, To adjust neeaie shred tension
16. Regulating the cake-vo sping
To adjust bobbin thread tension
18, Needie gosition selector
18, Stitch with regulator
20. How to contral the wieth of 2
3
21. Nadle bar frame clamaing device
22. Fittings for straight and zigzag stizehing
23. Cnanging the throat plate ana feed dog
24.0 mount thread unwinder
25. To use are spas! cae
26, To use the anvi-sail sieeve
27. Knee lifter
To mount knee itter
Knee operating nresser fect if
Knee operating stitch width contral
ing 120U51/83/631
29, Fittings for hem sewing (20U51/53/631
30.F
ngs for buttonrole st
ings for zipper and cord sewing (20U51/83/63)
31, Caring for your machine
32, Troubleshooting chart
33. Specifications1. APPLICATION
This SINGER Arisan Zigzag Machine is for
of width
Zigzag and ornamental stitching in a varie:
‘and stitch length
Perfect straight stitching
Superfine control of stitch length insures oer
stitching
satin
Mode! 20U §1 iSmm Bight, for Treadle)
53 (Gmm Bight)
62 (12mm Sight, for Embroidery)
63 (12mm Bight)
This machine is manufactured for artisan zigzag sewing
and 's sulted for sewing light weight and medium weight
materials
2. NOTES ON SAFETY
‘The machine must only be commissioned in fui
knowledge of the instruction manual and operated by
ersons with appropriate training
Betore putting into service, also read the safety notes:
ana the instruction manual of the motor supplies
The machine must be used only for tne purpose
intended, Use of the mactine without ihe safety devices:
belonging tot
ren gauge parts are excranged ie g. need! presser
foot, needle plate, feec dog and baboin-. during
threading, when the workplace is left uratterded, anc
during service work, the machine must be sso'sted from
the mains by swit off t witeh oF
disconnecting the mains plug,
(On mechanically operated clutch motors without start
inbisitor, it 8 necessary to wait until the mator nas
stoped
Gereral servicing work must be carried out oniy by
apercoriate’ dpersors
sonversion ard soat'e
maienarce
rican or perscns with
ervice of repair work on oneuratic systems the
ine must oe isolated from the compressed air
supply system, Exceptions to ‘his ate ony adjustments
ang function checks made by appropriately trained
technicians
Work on the electrical equipment must be carried out
only ay electhcians or appreorately tained persons.
Work on parts and systems under electric current is not
permitted, except as specifiec in regulations ENSO110,
Conversions or changes to the machine must oe mace
oniy on acherence to al satety regulations
For repairs, only reolecement parts approved by us must
2 used
‘~mssioning of the seving head 's pronibited unt
ume as the entire sews ng unit is found to comply
C regulations
jngs of the symbols:
Danger spot!
Items requiring special attention
Danger of imury to operative or service
staf.
Be sure to observe and adhere to these
safety notes!
Earth
3. COMMISSIONING
To avoid disturbances or damages, 1's
gosolute'y Necessary fo opserve the
‘owing instructions:
Before you put the machine into operation for the first
time, clean thoroughly and oll't well see page 2
Have the mechanic check whether the motor can oe
Used with existing mains voltage or not, and that junction
‘box is correctly connected. Co not start she machine f
the voltage 's not correct!
When the machine runs, the balance wheel must rotate
towerd the operator. ift does not, have the electrican
‘change the wares on the motor.